@@ -969,8 +969,6 @@ dtb-$(CONFIG_ARCH_IMX8M) += \
imx8mp-dhcom-pdk-overlay-eth2xfast.dtbo \
imx8mp-debix-model-a.dtb \
imx8mp-dhcom-drc02.dtb \
- imx8mp-dhcom-pdk2.dtb \
- imx8mp-dhcom-pdk3.dtb \
imx8mp-dhcom-pdk3-overlay-rev100.dtbo \
imx8mp-dhcom-picoitx.dtb \
imx8mp-icore-mx8mp-edimm2.2.dtb \
deleted file mode 100644
@@ -1,158 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (C) 2022 Marek Vasut <marex@denx.de>
- *
- * DHCOM iMX8MP variant:
- * DHCM-iMX8ML8-C160-R409-F1638-SPI16-GE-CAN2-SD-RTC-WBTA-ADC-T-RGB-CSI2-HS-I-01D2
- * DHCOM PCB number: 660-100 or newer
- * PDK2 PCB number: 516-400 or newer
- */
-
-/dts-v1/;
-
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/phy/phy-imx8-pcie.h>
-#include "imx8mp-dhcom-som.dtsi"
-
-/ {
- model = "DH electronics i.MX8M Plus DHCOM Premium Developer Kit (2)";
- compatible = "dh,imx8mp-dhcom-pdk2", "dh,imx8mp-dhcom-som",
- "fsl,imx8mp";
-
- chosen {
- stdout-path = &uart1;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- button-0 {
- gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; /* GPIO A */
- label = "TA1-GPIO-A";
- linux,code = <KEY_A>;
- pinctrl-0 = <&pinctrl_dhcom_a>;
- pinctrl-names = "default";
- wakeup-source;
- };
-
- button-1 {
- gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; /* GPIO B */
- label = "TA2-GPIO-B";
- linux,code = <KEY_B>;
- pinctrl-0 = <&pinctrl_dhcom_b>;
- pinctrl-names = "default";
- wakeup-source;
- };
-
- button-2 {
- gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; /* GPIO C */
- label = "TA3-GPIO-C";
- linux,code = <KEY_C>;
- pinctrl-0 = <&pinctrl_dhcom_c>;
- pinctrl-names = "default";
- wakeup-source;
- };
-
- button-3 {
- gpios = <&gpio4 27 GPIO_ACTIVE_LOW>; /* GPIO D */
- label = "TA4-GPIO-D";
- linux,code = <KEY_D>;
- pinctrl-0 = <&pinctrl_dhcom_d>;
- pinctrl-names = "default";
- wakeup-source;
- };
- };
-
- led {
- compatible = "gpio-leds";
-
- led-0 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* GPIO E */
- pinctrl-0 = <&pinctrl_dhcom_e>;
- pinctrl-names = "default";
- };
-
- led-1 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* GPIO F */
- pinctrl-0 = <&pinctrl_dhcom_f>;
- pinctrl-names = "default";
- };
-
- led-2 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; /* GPIO H */
- pinctrl-0 = <&pinctrl_dhcom_h>;
- pinctrl-names = "default";
- };
-
- led-3 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; /* GPIO I */
- pinctrl-0 = <&pinctrl_dhcom_i>;
- pinctrl-names = "default";
- };
- };
-};
-
-&fec { /* Second ethernet */
- pinctrl-0 = <&pinctrl_fec_rgmii>;
- phy-handle = <ðphypdk>;
- phy-mode = "rgmii";
-
- mdio {
- ethphypdk: ethernet-phy@7 { /* KSZ 9021 */
- compatible = "ethernet-phy-ieee802.3-c22";
- pinctrl-0 = <&pinctrl_ethphy1>;
- pinctrl-names = "default";
- interrupt-parent = <&gpio4>;
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
- max-speed = <100>;
- reg = <7>;
- reset-assert-us = <1000>;
- reset-deassert-us = <1000>;
- reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
- rxc-skew-ps = <3000>;
- rxd0-skew-ps = <0>;
- rxd1-skew-ps = <0>;
- rxd2-skew-ps = <0>;
- rxd3-skew-ps = <0>;
- rxdv-skew-ps = <0>;
- txc-skew-ps = <3000>;
- txd0-skew-ps = <0>;
- txd1-skew-ps = <0>;
- txd2-skew-ps = <0>;
- txd3-skew-ps = <0>;
- txen-skew-ps = <0>;
- };
- };
-};
-
-&flexcan1 {
- status = "okay";
-};
-
-&usb3_1 {
- fsl,over-current-active-low;
-};
-
-&iomuxc {
- /*
- * GPIO_A,B,C,D are connected to buttons.
- * GPIO_E,F,H,I are connected to LEDs.
- * GPIO_M is connected to CLKOUT2.
- */
- pinctrl-0 = <&pinctrl_hog_base
- &pinctrl_dhcom_g &pinctrl_dhcom_j
- &pinctrl_dhcom_k &pinctrl_dhcom_l
- &pinctrl_dhcom_int>;
-};
deleted file mode 100644
@@ -1,317 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (C) 2023 Marek Vasut <marex@denx.de>
- *
- * DHCOM iMX8MP variant:
- * DHCM-iMX8ML8-C160-R409-F1638-SPI16-GE-CAN2-SD-RTC-WBTA-ADC-T-RGB-CSI2-HS-I-01D2
- * DHCOM PCB number: 660-100 or newer
- * PDK3 PCB number: 669-100 or newer
- */
-
-/dts-v1/;
-
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/phy/phy-imx8-pcie.h>
-#include "imx8mp-dhcom-som.dtsi"
-
-/ {
- model = "DH electronics i.MX8M Plus DHCOM Premium Developer Kit (3)";
- compatible = "dh,imx8mp-dhcom-pdk3", "dh,imx8mp-dhcom-som",
- "fsl,imx8mp";
-
- chosen {
- stdout-path = &uart1;
- };
-
- clk_ext_audio_codec: clock-codec {
- #clock-cells = <0>;
- clock-frequency = <24000000>;
- compatible = "fixed-clock";
- };
-
- clk_xtal25: clk-xtal25 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-
- connector {
- compatible = "usb-c-connector";
- label = "USB-C";
- data-role = "dual";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- usb_c_0_hs_ep: endpoint {
- remote-endpoint = <&dwc3_0_hs_ep>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- usb_c_0_ss_ep: endpoint {
- remote-endpoint = <&ptn5150_in_ep>;
- };
- };
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
-
- button-0 {
- gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; /* GPIO A */
- label = "TA1-GPIO-A";
- linux,code = <KEY_A>;
- pinctrl-0 = <&pinctrl_dhcom_a>;
- pinctrl-names = "default";
- wakeup-source;
- };
-
- button-1 {
- gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; /* GPIO B */
- label = "TA2-GPIO-B";
- linux,code = <KEY_B>;
- pinctrl-0 = <&pinctrl_dhcom_b>;
- pinctrl-names = "default";
- wakeup-source;
- };
-
- button-2 {
- gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; /* GPIO C */
- label = "TA3-GPIO-C";
- linux,code = <KEY_C>;
- pinctrl-0 = <&pinctrl_dhcom_c>;
- pinctrl-names = "default";
- wakeup-source;
- };
-
- button-3 {
- gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; /* GPIO E */
- label = "TA4-GPIO-E";
- linux,code = <KEY_E>;
- pinctrl-0 = <&pinctrl_dhcom_e>;
- pinctrl-names = "default";
- wakeup-source;
- };
- };
-
- led {
- compatible = "gpio-leds";
-
- led-0 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- function-enumerator = <0>;
- gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>; /* GPIO D */
- pinctrl-0 = <&pinctrl_dhcom_d>;
- pinctrl-names = "default";
- };
-
- led-1 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- function-enumerator = <1>;
- gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* GPIO F */
- pinctrl-0 = <&pinctrl_dhcom_f>;
- pinctrl-names = "default";
- };
-
- led-2 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- function-enumerator = <2>;
- gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; /* GPIO G */
- pinctrl-0 = <&pinctrl_dhcom_g>;
- pinctrl-names = "default";
- };
-
- led-3 {
- color = <LED_COLOR_ID_GREEN>;
- default-state = "off";
- function = LED_FUNCTION_INDICATOR;
- function-enumerator = <3>;
- gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; /* GPIO I */
- pinctrl-0 = <&pinctrl_dhcom_i>;
- pinctrl-names = "default";
- };
- };
-
- reg_avdd: regulator-avdd { /* AUDIO_VDD */
- compatible = "regulator-fixed";
- regulator-always-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "AUDIO_VDD";
- };
-};
-
-&i2c5 {
- i2cmux@70 {
- compatible = "nxp,pca9540";
- reg = <0x70>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- i2cmuxed0: i2c@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- typec@3d {
- compatible = "nxp,ptn5150";
- reg = <0x3d>;
- interrupt-parent = <&gpio4>;
- interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ptn5150>;
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
-
- ptn5150_in_ep: endpoint {
- remote-endpoint = <&usb_c_0_ss_ep>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- ptn5150_out_ep: endpoint {
- remote-endpoint = <&dwc3_0_ss_ep>;
- };
- };
- };
- };
-
- power-sensor@40 {
- compatible = "ti,ina238";
- reg = <0x40>;
- shunt-resistor = <20000>; /* 0.02 R */
- ti,shunt-gain = <1>; /* Drop cca. 40mV */
- };
-
- eeprom_board: eeprom@54 {
- compatible = "atmel,24c04";
- pagesize = <16>;
- reg = <0x54>;
- };
-
- pcieclk: clk@6b {
- compatible = "skyworks,si52144";
- reg = <0x6b>;
- clocks = <&clk_xtal25>;
- #clock-cells = <1>;
- };
- };
-
- i2cmuxed1: i2c@1 { /* HDMI DDC I2C */
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
- };
- };
-};
-
-&fec { /* Second ethernet */
- pinctrl-0 = <&pinctrl_fec_rgmii>;
- phy-handle = <ðphypdk>;
- phy-mode = "rgmii-id";
-
- mdio {
- ethphypdk: ethernet-phy@7 { /* Micrel KSZ9131RNXI */
- compatible = "ethernet-phy-id0022.1642",
- "ethernet-phy-ieee802.3-c22";
- interrupt-parent = <&gpio4>;
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-0 = <&pinctrl_ethphy1>;
- pinctrl-names = "default";
- reg = <7>;
- reset-assert-us = <1000>;
- /* RESET_N signal rise time ~100ms */
- reset-deassert-us = <120000>;
- reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
- status = "okay";
- };
- };
-};
-
-&flexcan1 {
- status = "okay";
-};
-
-&pcie_phy {
- clocks = <&pcieclk 1>;
- clock-names = "ref";
- fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
- status = "okay";
-};
-
-&pcie {
- fsl,max-link-speed = <3>;
- reset-gpio = <&gpio1 6 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&usb_dwc3_0 {
- usb-role-switch;
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- dwc3_0_hs_ep: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&usb_c_0_hs_ep>;
- };
-
- dwc3_0_ss_ep: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&ptn5150_out_ep>;
- };
- };
-};
-
-&usb3_1 {
- fsl,disable-port-power-control;
- fsl,permanently-attached;
-};
-
-&usb_dwc3_1 {
- /* This port has USB5734 Hub connected to it, PWR/OC pins are unused */
- /delete-property/ pinctrl-names;
- /delete-property/ pinctrl-0;
-};
-
-&iomuxc {
- /*
- * GPIO_A,B,C,E are connected to buttons.
- * GPIO_D,F,G,I are connected to LEDs.
- * GPIO_H is connected to USB Hub RESET_N.
- * GPIO_M is connected to CLKOUT2.
- */
- pinctrl-0 = <&pinctrl_hog_base
- &pinctrl_dhcom_h &pinctrl_dhcom_j &pinctrl_dhcom_k
- &pinctrl_dhcom_l
- &pinctrl_dhcom_int>;
-
- pinctrl_ptn5150: ptn5150grp {
- fsl,pins = <
- MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25 0x40000000
- >;
- };
-};
@@ -12,7 +12,7 @@ CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_OFFSET=0xFE0000
CONFIG_ENV_SECT_SIZE=0x1000
CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="imx8mp-dhcom-pdk2"
+CONFIG_DEFAULT_DEVICE_TREE="freescale/imx8mp-dhcom-pdk2"
CONFIG_SPL_TEXT_BASE=0x920000
CONFIG_TARGET_IMX8MP_DH_DHCOM_PDK2=y
CONFIG_DM_RESET=y
@@ -48,7 +48,7 @@ CONFIG_USE_BOOTARGS=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run dh_update_env distro_bootcmd ; reset"
CONFIG_USE_PREBOOT=y
-CONFIG_DEFAULT_FDT_FILE="imx8mp-dhcom-pdk2.dtb"
+CONFIG_DEFAULT_FDT_FILE="freescale/imx8mp-dhcom-pdk2.dtb"
CONFIG_SYS_CBSIZE=2048
CONFIG_SYS_PBSIZE=2081
CONFIG_CONSOLE_MUX=y
@@ -144,6 +144,8 @@ CONFIG_MMC_SPEED_MODE_SET=y
CONFIG_PARTITION_TYPE_GUID=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_UPSTREAM=y
+CONFIG_OF_UPSTREAM_INCLUDE_LOCAL_FALLBACK_DTBOS=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_NOWHERE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
@@ -12,7 +12,7 @@ CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_OFFSET=0xFE0000
CONFIG_ENV_SECT_SIZE=0x1000
CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="imx8mp-dhcom-pdk3"
+CONFIG_DEFAULT_DEVICE_TREE="freescale/imx8mp-dhcom-pdk3"
CONFIG_SPL_TEXT_BASE=0x920000
CONFIG_TARGET_IMX8MP_DH_DHCOM_PDK2=y
CONFIG_DM_RESET=y
@@ -50,7 +50,7 @@ CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run dh_update_env distro_bootcmd ; reset"
CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="gpio clear GPIO1_11 ; sleep 0.1 ; gpio set GPIO1_11 ; sleep 0.1 ; i2c dev 4 && i2c mw 0x70 0 4 && i2c probe 0x2d && i2c mw 0x2d 0xaa55.2 0"
-CONFIG_DEFAULT_FDT_FILE="imx8mp-dhcom-pdk3.dtb"
+CONFIG_DEFAULT_FDT_FILE="freescale/imx8mp-dhcom-pdk3.dtb"
CONFIG_SYS_CBSIZE=2048
CONFIG_SYS_PBSIZE=2081
CONFIG_CONSOLE_MUX=y
@@ -147,6 +147,8 @@ CONFIG_MMC_SPEED_MODE_SET=y
CONFIG_PARTITION_TYPE_GUID=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_UPSTREAM=y
+CONFIG_OF_UPSTREAM_INCLUDE_LOCAL_FALLBACK_DTBOS=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_NOWHERE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
Enable OF_UPSTREAM to use upstream DT and add freescale/ prefix to the DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/ including *-u-boot.dtsi and DTBOs from arch/$(ARCH)/dts/ directory. Signed-off-by: Marek Vasut <marex@denx.de> --- Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Caleb Connolly <caleb.connolly@linaro.org> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Lothar Rubusch <l.rubusch@gmail.com> Cc: Michal Simek <michal.simek@amd.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Sumit Garg <sumit.garg@linaro.org> Cc: Tom Rini <trini@konsulko.com> Cc: u-boot@dh-electronics.com Cc: u-boot@lists.denx.de --- V2: Enable CONFIG_OF_UPSTREAM_INCLUDE_LOCAL_FALLBACK_DTBOS --- arch/arm/dts/Makefile | 2 - arch/arm/dts/imx8mp-dhcom-pdk2.dts | 158 -------------- arch/arm/dts/imx8mp-dhcom-pdk3.dts | 317 ---------------------------- configs/imx8mp_dhcom_pdk2_defconfig | 6 +- configs/imx8mp_dhcom_pdk3_defconfig | 6 +- 5 files changed, 8 insertions(+), 481 deletions(-) delete mode 100644 arch/arm/dts/imx8mp-dhcom-pdk2.dts delete mode 100644 arch/arm/dts/imx8mp-dhcom-pdk3.dts