diff mbox series

[v3,06/11] migration/docs: Update postcopy recover session for SETUP phase

Message ID 20240619223046.1798968-7-peterx@redhat.com
State New
Headers show
Series migration: New postcopy state, and some cleanups | expand

Commit Message

Peter Xu June 19, 2024, 10:30 p.m. UTC 
Firstly, the "Paused" state was added in the wrong place before. The state
machine section was describing PostcopyState, rather than MigrationStatus.
Drop the Paused state descriptions.

Then in the postcopy recover session, add more information on the state
machine for MigrationStatus in the lines.  Add the new RECOVER_SETUP phase.

Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Peter Xu <peterx@redhat.com>
---
 docs/devel/migration/postcopy.rst | 31 ++++++++++++++++---------------
 1 file changed, 16 insertions(+), 15 deletions(-)
diff mbox series

Patch

diff --git a/docs/devel/migration/postcopy.rst b/docs/devel/migration/postcopy.rst
index 6c51e96d79..a15594e11f 100644
--- a/docs/devel/migration/postcopy.rst
+++ b/docs/devel/migration/postcopy.rst
@@ -99,17 +99,6 @@  ADVISE->DISCARD->LISTEN->RUNNING->END
     (although it can't do the cleanup it would do as it
     finishes a normal migration).
 
- - Paused
-
-    Postcopy can run into a paused state (normally on both sides when
-    happens), where all threads will be temporarily halted mostly due to
-    network errors.  When reaching paused state, migration will make sure
-    the qemu binary on both sides maintain the data without corrupting
-    the VM.  To continue the migration, the admin needs to fix the
-    migration channel using the QMP command 'migrate-recover' on the
-    destination node, then resume the migration using QMP command 'migrate'
-    again on source node, with resume=true flag set.
-
  - End
 
     The listen thread can now quit, and perform the cleanup of migration
@@ -221,7 +210,8 @@  paused postcopy migration.
 
 The recovery phase normally contains a few steps:
 
-  - When network issue occurs, both QEMU will go into PAUSED state
+  - When network issue occurs, both QEMU will go into **POSTCOPY_PAUSED**
+    migration state.
 
   - When the network is recovered (or a new network is provided), the admin
     can setup the new channel for migration using QMP command
@@ -229,9 +219,20 @@  The recovery phase normally contains a few steps:
 
   - On source host, the admin can continue the interrupted postcopy
     migration using QMP command 'migrate' with resume=true flag set.
-
-  - After the connection is re-established, QEMU will continue the postcopy
-    migration on both sides.
+    Source QEMU will go into **POSTCOPY_RECOVER_SETUP** state trying to
+    re-establish the channels.
+
+  - When both sides of QEMU successfully reconnects using a new or fixed up
+    channel, they will go into **POSTCOPY_RECOVER** state, some handshake
+    procedure will be needed to properly synchronize the VM states between
+    the two QEMUs to continue the postcopy migration.  For example, there
+    can be pages sent right during the window when the network is
+    interrupted, then the handshake will guarantee pages lost in-flight
+    will be resent again.
+
+  - After a proper handshake synchronization, QEMU will continue the
+    postcopy migration on both sides and go back to **POSTCOPY_ACTIVE**
+    state.  Postcopy migration will continue.
 
 During a paused postcopy migration, the VM can logically still continue
 running, and it will not be impacted from any page access to pages that