| Message ID | 20240409175700.27535-4-chalapathi.v@linux.ibm.com |
|---|---|
| State | New |
| Headers | show |
| Series | hw/ppc: SPI model | expand |
Hello, Please rephrase the subject to something like: "ppc/pnv: Extend SPI model ..." Using a verb is preferable. On 4/9/24 19:56, Chalapathi V wrote: > In this commit SPI shift engine and sequencer logic is implemented. > Shift engine performs serialization and de-serialization according to the > control by the sequencer and according to the setup defined in the > configuration registers. Sequencer implements the main control logic and > FSM to handle data transmit and data receive control of the shift engine. > > Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com> > --- > include/hw/ppc/pnv_spi_controller.h | 72 ++ > hw/ppc/pnv_spi_controller.c | 1311 ++++++++++++++++++++++++++- > 2 files changed, 1382 insertions(+), 1 deletion(-) > > diff --git a/include/hw/ppc/pnv_spi_controller.h b/include/hw/ppc/pnv_spi_controller.h > index 5ec50fb14c..ee8e7a17da 100644 > --- a/include/hw/ppc/pnv_spi_controller.h > +++ b/include/hw/ppc/pnv_spi_controller.h > @@ -8,6 +8,14 @@ > * This model Supports a connection to a single SPI responder. > * Introduced for P10 to provide access to SPI seeproms, TPM, flash device > * and an ADC controller. > + * > + * All SPI function control is mapped into the SPI register space to enable > + * full control by firmware. > + * > + * SPI Controller has sequencer and shift engine. The SPI shift engine > + * performs serialization and de-serialization according to the control by > + * the sequencer and according to the setup defined in the configuration > + * registers and the SPI sequencer implements the main control logic. > */ > #include "hw/ssi/ssi.h" > > @@ -21,6 +29,7 @@ > #define SPI_CONTROLLER_REG_SIZE 8 > > typedef struct SSIBus SSIBus; > +typedef struct xfer_buffer xfer_buffer; Please use CamelCase names for typedef. The forward declaration doesn't seem useful. > #define TYPE_PNV_SPI_BUS "pnv-spi-bus" > OBJECT_DECLARE_SIMPLE_TYPE(PnvSPIBus, PNV_SPI_BUS) > @@ -33,6 +42,21 @@ typedef struct PnvSPIBus { > uint32_t id; > } PnvSPIBus; > > +/* xfer_buffer */ > +typedef struct xfer_buffer { > + > + uint32_t len; > + uint8_t *data; > + > +} xfer_buffer; > + > +uint8_t *xfer_buffer_write_ptr(xfer_buffer *payload, uint32_t offset, > + uint32_t length); > +void xfer_buffer_read_ptr(xfer_buffer *payload, uint8_t **read_buf, > + uint32_t offset, uint32_t length); > +xfer_buffer *xfer_buffer_new(void); > +void xfer_buffer_free(xfer_buffer *payload); > + I don't think these helper routines need to be defined in the header file of the PnvPsi model. They look internal to me. > typedef struct PnvSpiController { > DeviceState parent; > > @@ -40,6 +64,39 @@ typedef struct PnvSpiController { > MemoryRegion xscom_spic_regs; > /* SPI controller object number */ > uint32_t spic_num; > + uint8_t responder_select; > + /* To verify if shift_n1 happens prior to shift_n2 */ > + bool shift_n1_done; > + /* > + * Internal flags for the first and last indicators for the SPI > + * interface methods > + */ > + uint8_t first; > + uint8_t last; > + /* Loop counter for branch operation opcode Ex/Fx */ > + uint8_t loop_counter_1; > + uint8_t loop_counter_2; > + /* N1/N2_bits specifies the size of the N1/N2 segment of a frame in bits.*/ > + uint8_t N1_bits; > + uint8_t N2_bits; > + /* Number of bytes in a payload for the N1/N2 frame segment.*/ > + uint8_t N1_bytes; > + uint8_t N2_bytes; > + /* Number of N1/N2 bytes marked for transmit */ > + uint8_t N1_tx; > + uint8_t N2_tx; > + /* Number of N1/N2 bytes marked for receive */ > + uint8_t N1_rx; > + uint8_t N2_rx; > + /* > + * Setting this attribute to true will cause the engine to reverse the > + * bit order of each byte it appends to a payload before sending the > + * payload to a device. There may be cases where an end device expects > + * a reversed order, like in the case of the Nuvoton TPM device. The > + * order of bytes in the payload is not reversed, only the order of the > + * 8 bits in each payload byte. > + */ > + bool reverse_bits; > > /* SPI Controller registers */ > uint64_t error_reg; > @@ -52,4 +109,19 @@ typedef struct PnvSpiController { > uint8_t sequencer_operation_reg[SPI_CONTROLLER_REG_SIZE]; > uint64_t status_reg; > } PnvSpiController; > + > +void log_all_N_counts(PnvSpiController *spi_controller); > +void spi_response(PnvSpiController *spi_controller, int bits, > + xfer_buffer *rsp_payload); > +void operation_sequencer(PnvSpiController *spi_controller); > +bool operation_shiftn1(PnvSpiController *spi_controller, uint8_t opcode, > + xfer_buffer **payload, bool send_n1_alone); > +bool operation_shiftn2(PnvSpiController *spi_controller, uint8_t opcode, > + xfer_buffer **payload); > +bool does_rdr_match(PnvSpiController *spi_controller); > +uint8_t get_from_offset(PnvSpiController *spi_controller, uint8_t offset); > +void shift_byte_in(PnvSpiController *spi_controller, uint8_t byte); > +void calculate_N1(PnvSpiController *spi_controller, uint8_t opcode); > +void calculate_N2(PnvSpiController *spi_controller, uint8_t opcode); > +uint8_t reverse_bits8(uint8_t x); These routines are internal and belong to hw/ppc/pnv_spi_controller.c. Please don't export them. Also, adding a pnv_psi_ prefix would be a plus to identify the sympbols. > #endif /* PPC_PNV_SPI_CONTROLLER_H */ > diff --git a/hw/ppc/pnv_spi_controller.c b/hw/ppc/pnv_spi_controller.c > index e2478a47f2..afe7f17565 100644 > --- a/hw/ppc/pnv_spi_controller.c > +++ b/hw/ppc/pnv_spi_controller.c > @@ -52,6 +52,11 @@ static uint64_t pnv_spi_controller_read(void *opaque, hwaddr addr, > val)); > sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, sc->status_reg, 0); > SPI_DEBUG(qemu_log("RDR being read, RDR_full set to 0\n")); > + if (GETFIELD(STATUS_REG_SHIFTER_FSM, sc->status_reg) == FSM_WAIT) { > + SPI_DEBUG(qemu_log("RDR being read while shifter is waiting, " > + "starting sequencer\n")); Please use trace events instead. > + operation_sequencer(sc); > + } > break; > case SEQUENCER_OPERATION_REG: > val = 0; > @@ -124,13 +129,15 @@ static void pnv_spi_controller_write(void *opaque, hwaddr addr, > sc->status_reg = SETFIELD(STATUS_REG_TDR_UNDERRUN, sc->status_reg, 0); > SPI_DEBUG(qemu_log("TDR being written, TDR_underrun set to 0\n")); > SPI_DEBUG(qemu_log("TDR being written, starting sequencer\n")); > + operation_sequencer(sc); > + > break; > case RECEIVE_DATA_REG: > sc->receive_data_reg = val; > break; > case SEQUENCER_OPERATION_REG: > for (int i = 0; i < SPI_CONTROLLER_REG_SIZE; i++) { > - sc->sequencer_operation_reg[i] = (val >> (56 - i * 8)) & 0xFF; > + sc->sequencer_operation_reg[i] = (val >> (56 - i * 8)) & 0xFF; This change belongs to the previous patch. > } > break; > case STATUS_REG: > @@ -157,6 +164,1306 @@ static const MemoryRegionOps pnv_spi_controller_xscom_ops = { > .endianness = DEVICE_BIG_ENDIAN, > }; > > +/* xfer_buffer_methods */ > +xfer_buffer *xfer_buffer_new(void) > +{ > + xfer_buffer *payload = g_malloc0(sizeof(*payload)); > + > + payload->data = g_malloc0(payload->len); euh. payload->len is 0. This allocation is pointless. > + return payload; > +} > + > +void xfer_buffer_free(xfer_buffer *payload) > +{ > + free(payload->data); > + free(payload); > +} > + > +uint8_t *xfer_buffer_write_ptr(xfer_buffer *payload, uint32_t offset, > + uint32_t length) > +{ > + if (payload->len < (offset + length)) { > + payload->len = offset + length; > + payload->data = g_realloc(payload->data, payload->len); > + } > + return &payload->data[offset]; > +} > + > +void xfer_buffer_read_ptr(xfer_buffer *payload, uint8_t **read_buf, > + uint32_t offset, uint32_t length) > +{ > + static uint32_t prev_len; > + if ((prev_len != length) || (*read_buf == NULL)) { > + *read_buf = g_realloc(*read_buf, length); > + prev_len = length; > + } > + if (offset > payload->len) { > + /* Reading outside payload, just return */ > + return; > + } > + *read_buf = &payload->data[offset]; > +} Isn't there a maximum buffer size ? It would simplify the implementation and avoid all these alloc/realloc/free calls. > +uint8_t reverse_bits8(uint8_t x) > +{ > + x = (x << 4) | (x >> 4); > + x = ((x & 0x33) << 2) | ((x & 0xcc) >> 2); > + x = ((x & 0x55) << 1) | ((x & 0xaa) >> 1); > + return x; > +} revbit8() in qemu/host-utils.h should do the same. The rest is difficult to comment on without an intimitate knowledge of the controller and the datasheet. Can teammates help ? Thanks, C. > +bool does_rdr_match(PnvSpiController *sc) > +{ > + /* > + * According to spec, the mask bits that are 0 are compared and the > + * bits that are 1 are ignored. > + */ > + uint16_t rdr_match_mask = GETFIELD(MEMORY_MAPPING_REG_RDR_MATCH_MASK, > + sc->memory_mapping_reg); > + uint16_t rdr_match_val = GETFIELD(MEMORY_MAPPING_REG_RDR_MATCH_VAL, > + sc->memory_mapping_reg); > + if ((~rdr_match_mask & rdr_match_val) == ((~rdr_match_mask) & > + GETFIELD(PPC_BITMASK(48, 63), sc->receive_data_reg))) { > + SPI_DEBUG(qemu_log("RDR match successful, match=0x%4.4x, " > + "mask=0x%4.4x, RDR[48:63]=0x%4.4llx\n", > + rdr_match_val, rdr_match_mask, > + GETFIELD(PPC_BITMASK(48, 63), > + sc->receive_data_reg))); > + return true; > + } else { > + SPI_DEBUG(qemu_log("RDR match failed, match=0x%4.4x, mask=0x%4.4x, " > + "RDR[48:63]=0x%4.4llx\n", rdr_match_val, rdr_match_mask, > + GETFIELD(PPC_BITMASK(48, 63), sc->receive_data_reg))); > + return false; > + } > +} > + > +uint8_t get_from_offset(PnvSpiController *sc, uint8_t offset) > +{ > + uint8_t byte; > + > + /* > + * Offset is an index between 0 and SPI_CONTROLLER_REG_SIZE - 1 > + * Check the offset before using it. > + */ > + if (offset < SPI_CONTROLLER_REG_SIZE) { > + byte = (sc->transmit_data_reg >> (56 - offset * 8)) & 0xFF; > + } else { > + /* > + * Log an error and return a 0xFF since we have to assign something > + * to byte before returning. > + */ > + qemu_log_mask(LOG_GUEST_ERROR, "Invalid offset = %d used to get byte " > + "from TDR\n", offset); > + byte = 0xff; > + } > + return byte; > +} > + > +void shift_byte_in(PnvSpiController *sc, uint8_t byte) > +{ > + sc->receive_data_reg = (sc->receive_data_reg << 8) | byte; > + SPI_DEBUG(qemu_log("0x%2.2x shifted in, RDR now = 0x%16.16lx\n", byte, > + sc->receive_data_reg)); > +} > + > +void spi_response(PnvSpiController *sc, int bits, xfer_buffer *rsp_payload) > +{ > + uint8_t *read_buf = NULL; > + uint8_t ecc_count; > + uint8_t shift_in_count; > + > + /* > + * Processing here must handle: > + * - Which bytes in the payload we should move to the RDR > + * - Explicit mode counter configuration settings > + * - RDR full and RDR overrun status > + */ > + > + /* > + * First check that the response payload is the exact same > + * number of bytes as the request payload was > + */ > + if (rsp_payload->len != (sc->N1_bytes + sc->N2_bytes)) { > + qemu_log_mask(LOG_GUEST_ERROR, "Invalid response payload size in " > + "bytes, expected %d, got %d\n", > + (sc->N1_bytes + sc->N2_bytes), rsp_payload->len); > + } else { > + uint8_t ecc_control; > + SPI_DEBUG(qemu_log("SPI response received, payload len = %d\n", > + rsp_payload->len)); > + log_all_N_counts(sc); > + /* > + * Adding an ECC count let's us know when we have found a payload byte > + * that was shifted in but cannot be loaded into RDR. Bits 29-30 > + * equal to either 0b00 or 0b10 indicate that we are taking in data > + * with ECC and either applying the ECC or discarding it. > + */ > + ecc_count = 0; > + ecc_control = GETFIELD(PPC_BITMASK(29, 30), > + sc->clock_config_reset_control); > + if (ecc_control == 0 || ecc_control == 2) { > + ecc_count = 1; > + } > + /* > + * Use the N1_rx and N2_rx counts to control shifting data from the > + * payload into the RDR. Keep an overall count of the number of bytes > + * shifted into RDR so we can discard every 9th byte when ECC is > + * enabled. > + */ > + shift_in_count = 0; > + /* Handle the N1 portion of the frame first */ > + if (sc->N1_rx != 0) { > + uint8_t n1_count = 0; > + while (n1_count < sc->N1_bytes) { > + shift_in_count++; > + xfer_buffer_read_ptr(rsp_payload, &read_buf, n1_count, 1); > + if ((ecc_count != 0) && > + (shift_in_count == (SPI_CONTROLLER_REG_SIZE + ecc_count))) { > + SPI_DEBUG(qemu_log("Discarding rx N1 ECC byte = 0x%2.2x at " > + "payload index = %d\n", read_buf[0], n1_count)); > + shift_in_count = 0; > + } else { > + uint8_t n1_byte = 0x00; > + n1_byte = read_buf[0]; > + SPI_DEBUG(qemu_log("Extracting rx n1_byte = 0x%2.2x from " > + "payload at index = %d\n", n1_byte, n1_count)); > + if (sc->reverse_bits) { > + SPI_DEBUG(qemu_log("Reversing bit order of rx " > + "n1_byte\n")); > + n1_byte = reverse_bits8(n1_byte); > + } > + SPI_DEBUG(qemu_log("Shifting rx N1 byte = 0x%2.2x into " > + "RDR\n", n1_byte)); > + shift_byte_in(sc, n1_byte); > + } > + n1_count++; > + } /* end of while */ > + } > + /* Handle the N2 portion of the frame */ > + if (sc->N2_rx != 0) { > + uint8_t n2_count = 0; > + while (n2_count < sc->N2_bytes) { > + shift_in_count++; > + xfer_buffer_read_ptr(rsp_payload, &read_buf, > + (sc->N1_bytes + n2_count), 1); > + if ((ecc_count != 0) && > + (shift_in_count == (SPI_CONTROLLER_REG_SIZE + ecc_count))) { > + SPI_DEBUG(qemu_log("Discarding rx N1 ECC byte = 0x%2.2x at " > + "payload index = %d\n", read_buf[0], > + (sc->N1_bytes + n2_count))); > + shift_in_count = 0; > + } else { > + /* > + * The code handles shifting data from the payload received > + * from the responder into the responder's RDR. Since this > + * is an N2 frame segment it is safe to assume that there > + * was a preceding N1 segment which was combined with an N2 > + * segment to create a single frame. The response data will > + * then have N1_bytes of data in the payload representing a > + * responder response to the N1 section of the frame. If N2 > + * is set to receive the shifting for N2 data begins after > + * the N1 bytes regardless of whether or not N1 was marked > + * for transmit or receive. > + */ > + uint8_t n2_byte = 0x00; > + n2_byte = read_buf[0]; > + SPI_DEBUG(qemu_log("Extracting rx n2_byte = 0x%2.2x from " > + "payload at index = %d\n", n2_byte, > + (sc->N1_bytes + n2_count))); > + if (sc->reverse_bits) { > + SPI_DEBUG(qemu_log("Reversing bit order of rx " > + "n2_byte\n")); > + n2_byte = reverse_bits8(n2_byte); > + } > + SPI_DEBUG(qemu_log("Shifting rx N2 byte = 0x%2.2x into " > + "RDR\n", n2_byte)); > + shift_byte_in(sc, n2_byte); > + } > + n2_count++; > + } > + } > + if ((sc->N1_rx + sc->N2_rx) > 0) { > + /* > + * Data was received so handle RDR status. > + * It is easier to handle RDR_full and RDR_overrun status here > + * since the RDR register's shift_byte_in method is called > + * multiple times in a row. Controlling RDR status is done here > + * instead of in the RDR scoped methods for that reason. > + */ > + if (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1) { > + /* > + * Data was shifted into the RDR before having been read > + * causing previous data to have been overrun. > + */ > + sc->status_reg = SETFIELD(STATUS_REG_RDR_OVERRUN, > + sc->status_reg, 1); > + } else { > + /* > + * Set status to indicate that the received data register is > + * full. This flag is only cleared once the RDR is unloaded. > + */ > + sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, > + sc->status_reg, 1); > + SPI_DEBUG(qemu_log("RDR_full set to 1\n")); > + } > + } > + } /* end of else */ > +} /* end of spi_response() */ > + > +void log_all_N_counts(PnvSpiController *sc) > +{ > + SPI_DEBUG(qemu_log("N1_bits = %d, N1_bytes = %d, N1_tx = %d, N1_rx = %d, " > + "N2_bits = %d, N2_bytes = %d, N2_tx = %d, N2_rx = %d\n", > + sc->N1_bits, sc->N1_bytes, sc->N1_tx, sc->N1_rx, sc->N2_bits, > + sc->N2_bytes, sc->N2_tx, sc->N2_rx)); > +} > + > +static inline void next_sequencer_fsm(PnvSpiController *sc) > +{ > + uint8_t seq_index = GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg); > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg, > + (seq_index + 1)); > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg, > + SEQ_STATE_INDEX_INCREMENT); > +} > + > +void operation_sequencer(PnvSpiController *sc) > +{ > + /* > + * Loop through each sequencer operation ID and perform the requested > + * operations. > + * Flag for indicating if we should send the N1 frame or wait to combine > + * it with a preceding N2 frame. > + */ > + bool send_n1_alone = true; > + bool stop = false; /* Flag to stop the sequencer */ > + uint8_t opcode = 0; > + uint8_t masked_opcode = 0; > + > + /* > + * xfer_buffer for containing the payload of the SPI frame. > + * This is a static because there are cases where a sequence has to stop > + * and wait for the target application to unload the RDR. If this occurs > + * during a sequence where N1 is not sent alone and instead combined with > + * N2 since the N1 tx length + the N2 tx length is less than the size of > + * the TDR. > + */ > + static xfer_buffer *payload; > + > + if (payload == NULL) { > + payload = xfer_buffer_new(); > + } > + /* > + * Clear the sequencer FSM error bit - general_SPI_status[3] > + * before starting a sequence. > + */ > + sc->status_reg = SETFIELD(PPC_BIT(35), sc->status_reg, 0); > + /* > + * If the FSM is idle set the sequencer index to 0 > + * (new/restarted sequence) > + */ > + if (GETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg) == > + SEQ_STATE_IDLE) { > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg, 0); > + } > + /* > + * There are only 8 possible operation IDs to iterate through though > + * some operations may cause more than one frame to be sequenced. > + */ > + while (GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg) < 8) { > + opcode = sc->sequencer_operation_reg[GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, sc->status_reg)]; > + /* Set sequencer state to decode */ > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg, > + SEQ_STATE_DECODE); > + /* > + * Only the upper nibble of the operation ID is needed to know what > + * kind of operation is requested. > + */ > + masked_opcode = opcode & 0xF0; > + switch (masked_opcode) { > + /* > + * Increment the operation index in each case instead of just > + * once at the end in case an operation like the branch > + * operation needs to change the index. > + */ > + case SEQ_OP_STOP: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + /* A stop operation in any position stops the sequencer */ > + SPI_DEBUG(qemu_log("Sequencer STOP at index = 0x%llx, sequencer " > + "idling\n", GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg))); > + stop = true; > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, sc->status_reg, > + FSM_IDLE); > + sc->loop_counter_1 = 0; > + sc->loop_counter_2 = 0; > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_IDLE); > + break; > + > + case SEQ_OP_SELECT_SLAVE: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + SPI_DEBUG(qemu_log("Sequencer SELECT_SLAVE at index = 0x%llx\n", > + GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); > + /* > + * This device currently only supports a single responder > + * connection at position 0. De-selecting a responder is fine > + * and expected at the end of a sequence but selecting any > + * responder other than 0 should cause an error. > + */ > + sc->responder_select = opcode & 0x0F; > + if (sc->responder_select == 0) { > + SPI_DEBUG(qemu_log("Shifter done, pull the CS line high\n")); > + qemu_set_irq((sc->bus).cs_line[0], 1); > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg, > + (GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg) + 1)); > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_DONE); > + } else if (sc->responder_select != 1) { > + qemu_log_mask(LOG_GUEST_ERROR, "Slave selection other than 1 " > + "not supported, select = 0x%x\n", > + sc->responder_select); > + SPI_DEBUG(qemu_log("Sequencer stop requested due to invalid " > + "responder select at index = 0x%llx, " > + "shifter idling\n", GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg))); > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_IDLE); > + stop = true; > + } else { > + /* > + * Only allow an FSM_START state when a responder is > + * selected > + */ > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_START); > + SPI_DEBUG(qemu_log("shifter starting, pull CS line low\n")); > + qemu_set_irq((sc->bus).cs_line[0], 0); > + sc->first = 1; > + sc->last = 0; > + /* > + * A Shift_N2 operation is only valid after a Shift_N1 > + * according to the spec. The spec doesn't say if that means > + * immediately after or just after at any point. We will track > + * the occurrence of a Shift_N1 to enforce this requirement in > + * the most generic way possible by assuming that the rule > + * applies once a valid responder select has occurred. > + */ > + sc->shift_n1_done = false; > + next_sequencer_fsm(sc); > + } > + break; > + > + case SEQ_OP_SHIFT_N1: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + SPI_DEBUG(qemu_log("Sequencer SHIFT_N1 at index = 0x%llx\n", > + GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); > + /* > + * Only allow a shift_n1 when the state is not IDLE or DONE. > + * In either of those two cases the sequencer is not in a proper > + * state to perform shift operations because the sequencer has: > + * - processed a responder deselect (DONE) > + * - processed a stop opcode (IDLE) > + * - encountered an error (IDLE) > + */ > + if ((GETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg) == FSM_IDLE) || > + (GETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg) == FSM_DONE)) { > + qemu_log_mask(LOG_GUEST_ERROR, "Shift_N1 not allowed in " > + "shifter state = 0x%llx", GETFIELD( > + STATUS_REG_SHIFTER_FSM, sc->status_reg)); > + /* > + * Set sequencer FSM error bit 3 (general_SPI_status[3]) > + * in status reg. > + */ > + sc->status_reg = SETFIELD(PPC_BIT(35), sc->status_reg, 1); > + SPI_DEBUG(qemu_log("Sequencer stop requested due to invalid " > + "shifter state at index = 0x%llx\n", GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); > + stop = true; > + } else { > + /* > + * Look for the special case where there is a shift_n1 set for > + * transmit and it is followed by a shift_n2 set for transmit > + * AND the combined transmit length of the two operations is > + * less than or equal to the size of the TDR register. In this > + * case we want to use both this current shift_n1 opcode and the > + * following shift_n2 opcode to assemble the frame for > + * transmission to the responder without requiring a refill of > + * the TDR between the two operations. > + */ > + if ((sc->sequencer_operation_reg[GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, sc->status_reg) + 1] & 0xF0) > + == SEQ_OP_SHIFT_N2) { > + SPI_DEBUG(qemu_log("Not sending N1 alone\n")); > + send_n1_alone = false; > + } > + /* > + * If the next opcode is 0x10, which deselects the SPI device > + * then this is the last shift > + */ > + if (sc->sequencer_operation_reg[GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, sc->status_reg) + 1] == > + SEQ_OP_SELECT_SLAVE) { > + sc->last = 1; > + } > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_SHIFT_N1); > + stop = operation_shiftn1(sc, opcode, &payload, send_n1_alone); > + if (stop) { > + /* > + * The operation code says to stop, this can occur if: > + * (1) RDR is full and the N1 shift is set for receive > + * (2) TDR was empty at the time of the N1 shift so we need > + * to wait for data. > + * (3) Neither 1 nor 2 are occurring and we aren't sending > + * N1 alone and N2 counter reload is set (bit 0 of the N2 > + * counter reload field). In this case TDR_underrun will > + * will be set and the Payload has been loaded so it is > + * ok to advance the sequencer. > + */ > + if (GETFIELD(STATUS_REG_TDR_UNDERRUN, sc->status_reg)) { > + SPI_DEBUG(qemu_log("Sequencer stop requested due to N2 " > + "counter reload active.\n")); > + sc->shift_n1_done = true; > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, > + FSM_SHIFT_N2); > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg, > + (GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg) + 1)); > + SPI_DEBUG(qemu_log("Set new sequencer index to = " > + "0x%llx\n", GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg))); > + } else { > + /* > + * This is case (1) or (2) so the sequencer needs to > + * wait and NOT go to the next sequence yet. > + */ > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_WAIT); > + } > + } else { > + /* Ok to move on to the next index */ > + sc->shift_n1_done = true; > + next_sequencer_fsm(sc); > + } > + } > + break; > + > + case SEQ_OP_SHIFT_N2: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + SPI_DEBUG(qemu_log("Sequencer SHIFT_N2 at index = %lld\n", > + GETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg))); > + if (!sc->shift_n1_done) { > + qemu_log_mask(LOG_GUEST_ERROR, "Shift_N2 is not allowed if a " > + "Shift_N1 is not done, shifter state = 0x%llx", > + GETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg)); > + /* > + * In case the sequencer actually stops if an N2 shift is > + * requested before any N1 shift is done. Set sequencer FSM > + * error bit 3 (general_SPI_status[3]) in status reg. > + */ > + sc->status_reg = SETFIELD(PPC_BIT(35), sc->status_reg, 1); > + SPI_DEBUG(qemu_log("Sequencer stop requested due to shift_n2 " > + "w/no shift_n1 done at index = 0x%llx\n", > + GETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg))); > + stop = true; > + } else { > + /* > + * If the next opcode is 0x10, which deselects the SPI device > + * then this is the last shift > + */ > + if (sc->sequencer_operation_reg[GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg) + 1] == SEQ_OP_SELECT_SLAVE) { > + sc->last = 1; > + } > + /* Ok to do a Shift_N2 */ > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_SHIFT_N2); > + stop = operation_shiftn2(sc, opcode, &payload); > + /* > + * If the operation code says to stop set the shifter state to > + * wait and stop > + */ > + if (stop) { > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_WAIT); > + } else { > + /* Ok to move on to the next index */ > + next_sequencer_fsm(sc); > + } > + } > + break; > + > + case SEQ_OP_BRANCH_IFNEQ_RDR: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_RDR at " > + "index = 0x%llx\n", GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); > + /* > + * The memory mapping register RDR match value is compared against > + * the 16 rightmost bytes of the RDR (potentially with masking). > + * Since this comparison is performed against the contents of the > + * RDR then a receive must have previously occurred otherwise > + * there is no data to compare and the operation cannot be > + * completed and will stop the sequencer until RDR full is set to > + * 1. > + */ > + if (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1) { > + bool rdr_matched = false; > + rdr_matched = does_rdr_match(sc); > + if (rdr_matched) { > + SPI_DEBUG(qemu_log("Proceed to next sequencer index " > + "(increment on RDR match)\n")); > + /* A match occurred, increment the sequencer index. */ > + next_sequencer_fsm(sc); > + } else { > + SPI_DEBUG(qemu_log("Proceed to sequencer index=0x%x " > + "(branch on RDR match fail)\n", (opcode & 0x7))); > + /* > + * Branch the sequencer to the index coded into the op > + * code. > + */ > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg, (opcode & 0x7)); > + } > + /* > + * Regardless of where the branch ended up we want the > + * sequencer to continue shifting so we have to clear > + * RDR_full. > + */ > + sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, > + sc->status_reg, 0); > + } else { > + SPI_DEBUG(qemu_log("RDR not full for 0x6x opcode! Stopping " > + "sequencer.\n")); > + stop = true; > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, > + sc->status_reg, FSM_WAIT); > + } > + break; > + > + case SEQ_OP_TRANSFER_TDR: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + qemu_log_mask(LOG_GUEST_ERROR, "Transfer TDR is not supported\n"); > + next_sequencer_fsm(sc); > + break; > + > + case SEQ_OP_BRANCH_IFNEQ_INC_1: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_INC_1 at index = " > + "0x%llx, next index = %d, count_compare_1 = " > + "0x%llx, loop_counter_1 = %d\n", GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, sc->status_reg), > + (opcode & 0x07), > + GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, > + sc->status_reg), sc->loop_counter_1)); > + /* > + * The spec says the loop should execute count compare + 1 times. > + * However we learned from engineering that we really only loop > + * count_compare times, count compare = 0 makes this op code a > + * no-op > + */ > + if (sc->loop_counter_1 != > + GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, > + sc->counter_config_reg)) { > + /* > + * If the next opcode is 0x10, which deselects the SPI device > + * and we know that the next opcode is the last one in the > + * loop then the next shift is the last shift > + */ > + uint8_t condition1 = sc->sequencer_operation_reg[ > + GETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg) + 1]; > + uint8_t condition2 = GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, > + sc->counter_config_reg); > + > + if ((condition1 == SEQ_OP_SELECT_SLAVE) && > + ((sc->loop_counter_1 + 1) == condition2)) { > + sc->last = 1; > + } > + /* > + * Next index is the lower nibble of the branch operation ID, > + * mask off all but the first three bits so we don't try to > + * access beyond the sequencer_operation_reg boundary. > + */ > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg, (opcode & 0x7)); > + sc->loop_counter_1++; > + SPI_DEBUG(qemu_log("Branching to index = %d, loop_counter_1 = " > + "%d\n", (opcode & 0x7), sc->loop_counter_1)); > + } else { > + /* Continue to next index if loop counter is reached */ > + next_sequencer_fsm(sc); > + SPI_DEBUG(qemu_log("loop counter 1 achieved, next sequencer " > + "index = 0x%llx\n", GETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg))); > + } > + break; > + > + case SEQ_OP_BRANCH_IFNEQ_INC_2: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_INC_2 at index = " > + "0x%llx, next index = %d, count_compare_2 = " > + "0x%llx, loop_counter_2 = %d\n", GETFIELD( > + STATUS_REG_SEQUENCER_INDEX, sc->status_reg), > + (opcode & 0x07), GETFIELD( > + COUNTER_CONFIG_REG_COUNT_COMPARE2, > + sc->status_reg), sc->loop_counter_2)); > + /* > + * If the next opcode is 0x10, which deselects the SPI device > + * and we know that the next opcode is the last one in the > + * loop then the next shift is the last shift > + */ > + uint8_t condition1 = sc->sequencer_operation_reg[ > + GETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg) + 1]; > + uint8_t condition2 = GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE2, > + sc->counter_config_reg); > + > + if ((condition1 == SEQ_OP_SELECT_SLAVE) && > + ((sc->loop_counter_2 + 1) == condition2)) { > + sc->last = 1; > + } > + /* > + * The spec says the loop should execute count compare + 1 times. > + * However we learned from engineering that we really only loop > + * count_compare times, count compare = 0 makes this op code a > + * no-op > + */ > + if (sc->loop_counter_2 != condition2) { > + /* > + * Next index is the lower nibble of the branch operation ID, > + * mask off all but the first three bits so we don't try to > + * access beyond the sequencer_operation_reg boundary. > + */ > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg, > + (opcode & 0x7)); > + sc->loop_counter_2++; > + SPI_DEBUG(qemu_log("Branching to index = %d, loop_counter_2 " > + "= %d", (opcode & 0x7), > + sc->loop_counter_2)); > + } else { > + /* Continue to next index if loop counter is reached */ > + next_sequencer_fsm(sc); > + SPI_DEBUG(qemu_log("loop counter 2 achieved, next sequencer " > + "index = 0x%llx\n", GETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg))); > + } > + break; > + > + default: > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_EXECUTE); > + qemu_log_mask(LOG_GUEST_ERROR, "Sequencer opcode 0x%x is not " > + "supported\n", opcode); > + /* Ignore unsupported operations. */ > + next_sequencer_fsm(sc); > + break; > + } /* end of switch */ > + /* > + * If we used all 8 opcodes without seeing a 00 - STOP in the sequence > + * we need to go ahead and end things as if there was a STOP at the > + * end. > + */ > + if (GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg) == 8) { > + SPI_DEBUG(qemu_log("All 8 opcodes completed, sequencer " > + "idling\n")); > + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, sc->status_reg, > + FSM_IDLE); > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, > + sc->status_reg, 0); > + sc->loop_counter_1 = 0; > + sc->loop_counter_2 = 0; > + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, > + sc->status_reg, SEQ_STATE_IDLE); > + break; > + } > + /* Break the loop if a stop was requested */ > + if (stop) { > + break; > + } > + } /* end of while */ > + return; > +} /* end of operation_sequencer() */ > + > +/* > + * Calculate the N1 counters based on passed in opcode and > + * internal register values. > + * The method assumes that the opcode is a Shift_N1 opcode > + * and doesn't test it. > + * The counters returned are: > + * N1 bits: Number of bits in the payload data that are significant > + * to the responder. > + * N1_bytes: Total count of payload bytes for the N1 (portion of the) frame. > + * N1_tx: Total number of bytes taken from TDR for N1 > + * N1_rx: Total number of bytes taken from the payload for N1 > + */ > +void calculate_N1(PnvSpiController *sc, uint8_t opcode) > +{ > + /* > + * Shift_N1 opcode form: 0x3M > + * Implicit mode: > + * If M != 0 the shift count is M bytes and M is the number of tx bytes. > + * Forced Implicit mode: > + * M is the shift count but tx and rx is determined by the count control > + * register fields. Note that we only check for forced Implicit mode when > + * M != 0 since the mode doesn't make sense when M = 0. > + * Explicit mode: > + * If M == 0 then shift count is number of bits defined in the > + * Counter Configuration Register's shift_count_N1 field. > + */ > + if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) { > + /* Explicit mode */ > + sc->N1_bits = GETFIELD(COUNTER_CONFIG_REG_SHIFT_COUNT_N1, > + sc->counter_config_reg); > + sc->N1_bytes = ceil(sc->N1_bits / 8); > + sc->N1_tx = 0; > + sc->N1_rx = 0; > + /* If tx count control for N1 is set, load the tx value */ > + if (GETFIELD(PPC_BIT(50), sc->counter_config_reg) == 1) { > + sc->N1_tx = sc->N1_bytes; > + } > + /* If rx count control for N1 is set, load the rx value */ > + if (GETFIELD(PPC_BIT(51), sc->counter_config_reg) == 1) { > + sc->N1_rx = sc->N1_bytes; > + } > + } else { > + /* Implicit mode/Forced Implicit mode, use M field from opcode */ > + sc->N1_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode); > + sc->N1_bits = sc->N1_bytes * 8; > + /* > + * Assume that we are going to transmit the count > + * (pure Implicit only) > + */ > + sc->N1_tx = sc->N1_bytes; > + sc->N1_rx = 0; > + /* Let Forced Implicit mode have an effect on the counts */ > + if (GETFIELD(PPC_BIT(49), sc->counter_config_reg) == 1) { > + /* > + * If Forced Implicit mode and count control doesn't > + * indicate transmit then reset the tx count to 0 > + */ > + if (GETFIELD(PPC_BIT(50), sc->counter_config_reg) == 0) { > + sc->N1_tx = 0; > + } > + /* If rx count control for N1 is set, load the rx value */ > + if (GETFIELD(PPC_BIT(51), sc->counter_config_reg) == 1) { > + sc->N1_rx = sc->N1_bytes; > + } > + } > + } > + /* > + * Enforce an upper limit on the size of N1 that is equal to the known size > + * of the shift register, 64 bits or 72 bits if ECC is enabled. > + * If the size exceeds 72 bits it is a user error so log an error, > + * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM > + * error bit. > + */ > + uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30), > + sc->clock_config_reset_control); > + if (ecc_control == 0 || ecc_control == 2) { > + if (sc->N1_bytes > (SPI_CONTROLLER_REG_SIZE + 1)) { > + qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size when " > + "ECC enabled, bytes = 0x%x, bits = 0x%x\n", > + sc->N1_bytes, sc->N1_bits); > + sc->N1_bytes = SPI_CONTROLLER_REG_SIZE + 1; > + sc->N1_bits = sc->N1_bytes * 8; > + } > + } else if (sc->N1_bytes > SPI_CONTROLLER_REG_SIZE) { > + qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size, " > + "bytes = 0x%x, bits = 0x%x\n", > + sc->N1_bytes, sc->N1_bits); > + sc->N1_bytes = SPI_CONTROLLER_REG_SIZE; > + sc->N1_bits = sc->N1_bytes * 8; > + } > +} /* end of calculate_N1 */ > + > +/* > + * Shift_N1 operation handler method > + */ > +bool operation_shiftn1(PnvSpiController *sc, uint8_t opcode, > + xfer_buffer **payload, bool send_n1_alone) > +{ > + uint8_t n1_count; > + bool stop = false; > + > + /* > + * If there isn't a current payload left over from a stopped sequence > + * create a new one. > + */ > + if (*payload == NULL) { > + SPI_DEBUG(qemu_log("Creating new payload xfer_buffer\n")); > + *payload = xfer_buffer_new(); > + } > + /* > + * Use a combination of N1 counters to build the N1 portion of the > + * transmit payload. > + * We only care about transmit at this time since the request payload > + * only represents data going out on the controller output line. > + * Leave mode specific considerations in the calculate function since > + * all we really care about are counters that tell use exactly how > + * many bytes are in the payload and how many of those bytes to > + * include from the TDR into the payload. > + */ > + calculate_N1(sc, opcode); > + SPI_DEBUG(qemu_log("Shift N1 started..\n")); > + log_all_N_counts(sc); > + /* > + * Zero out the N2 counters here in case there is no N2 operation following > + * the N1 operation in the sequencer. This keeps leftover N2 information > + * from interfering with spi_response logic. > + */ > + sc->N2_bits = 0; > + sc->N2_bytes = 0; > + sc->N2_tx = 0; > + sc->N2_rx = 0; > + /* > + * N1_bytes is the overall size of the N1 portion of the frame regardless of > + * whether N1 is used for tx, rx or both. Loop over the size to build a > + * payload that is N1_bytes long. > + * N1_tx is the count of bytes to take from the TDR and "shift" into the > + * frame which means append those bytes to the payload for the N1 portion > + * of the frame. > + * If N1_tx is 0 or if the count exceeds the size of the TDR append 0xFF to > + * the frame until the overall N1 count is reached. > + */ > + n1_count = 0; > + while (n1_count < sc->N1_bytes) { > + /* > + * Assuming that if N1_tx is not equal to 0 then it is the same as > + * N1_bytes. > + */ > + if ((sc->N1_tx != 0) && (n1_count < SPI_CONTROLLER_REG_SIZE)) { > + > + if (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1) { > + /* > + * Note that we are only appending to the payload IF the TDR > + * is full otherwise we don't touch the payload because we are > + * going to NOT send the payload and instead tell the sequencer > + * that called us to stop and wait for a TDR write so we have > + * data to load into the payload. > + */ > + uint8_t n1_byte = 0x00; > + n1_byte = get_from_offset(sc, n1_count); > + SPI_DEBUG(qemu_log("Extracting tx n1_byte = 0x%2.2x at index " > + "%d from TDR\n", n1_byte, n1_count)); > + if (sc->reverse_bits) { > + SPI_DEBUG(qemu_log("Reversing bit order of tx n1_byte\n")); > + n1_byte = reverse_bits8(n1_byte); > + } > + SPI_DEBUG(qemu_log("Appending tx n1_byte = 0x%2.2x to " > + "Payload\n", n1_byte)); > + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = > + n1_byte; > + } else { > + /* > + * We hit a shift_n1 opcode TX but the TDR is empty, tell the > + * sequencer to stop and break this loop. > + */ > + SPI_DEBUG(qemu_log("Shift N1 set for transmit but TDR is empty," > + " requesting sequencer stop\n")); > + stop = true; > + break; > + } > + } else { > + /* > + * Cases here: > + * - we are receiving during the N1 frame segment and the RDR > + * is full so we need to stop until the RDR is read > + * - we are transmitting and we don't care about RDR status > + * since we won't be loading RDR during the frame segment. > + * - we are receiving and the RDR is empty so we allow the operation > + * to proceed. > + */ > + if ((sc->N1_rx != 0) && (GETFIELD(STATUS_REG_RDR_FULL, > + sc->status_reg) == 1)) { > + SPI_DEBUG(qemu_log("Shift N1 set for receive but RDR is full, " > + "requesting sequencer stop\n")); > + stop = true; > + break; > + } else { > + SPI_DEBUG(qemu_log("Appending tx n1_byte = 0xFF to Payload\n")); > + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = 0xff; > + } > + } > + n1_count++; > + } /* end of while */ > + /* > + * If we are not stopping due to an empty TDR and we are doing an N1 TX > + * and the TDR is full we need to clear the TDR_full status. > + * Do this here instead of up in the loop above so we don't log the message > + * in every loop iteration. > + * Ignore the send_n1_alone flag, all that does is defer the TX until the N2 > + * operation, which was found immediately after the current opcode. The TDR > + * was unloaded and will be shifted so we have to clear the TDR_full status. > + */ > + if (!stop && (sc->N1_tx != 0) && > + (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1)) { > + > + sc->status_reg = SETFIELD(STATUS_REG_TDR_FULL, sc->status_reg, 0); > + SPI_DEBUG(qemu_log("TDR_full set to 0\n")); > + } > + /* > + * There are other reasons why the shifter would stop, such as a TDR empty > + * or RDR full condition with N1 set to receive. If we haven't stopped due > + * to either one of those conditions then check if the send_n1_alone flag is > + * equal to False, indicating the next opcode is an N2 operation, AND if > + * the N2 counter reload switch (bit 0 of the N2 count control field) is > + * set. This condition requires a pacing write to "kick" off the N2 > + * shift which includes the N1 shift as well when send_n1_alone is False. > + */ > + if (!stop && !send_n1_alone && > + (GETFIELD(PPC_BIT(52), sc->counter_config_reg) == 1)) { > + SPI_DEBUG(qemu_log("N2 counter reload active, stop N1 shift, " > + "TDR_underrun set to 1\n")); > + stop = true; > + sc->status_reg = SETFIELD(STATUS_REG_TDR_UNDERRUN, sc->status_reg, 1); > + } > + /* > + * If send_n1_alone is set AND we have a full TDR then this is the first and > + * last payload to send and we don't have an N2 frame segment to add to the > + * payload. > + */ > + if (send_n1_alone && !stop) { > + uint32_t tx; > + uint32_t rx; > + uint8_t *read_buf = NULL; > + xfer_buffer *rsp_payload = NULL; > + > + /* We have a TX and a full TDR or an RX and an empty RDR */ > + SPI_DEBUG(qemu_log("Shifting N1 frame: first = %d, last = %d, " > + "n1 bits = %d\n", sc->first, sc->last, > + sc->N1_bits)); > + rsp_payload = xfer_buffer_new(); > + for (int offset = 0; offset < (*payload)->len; offset = offset + 4) { > + xfer_buffer_read_ptr(*payload, &read_buf, offset, 4); > + tx = 0; > + for (int i = 0; i < 4; i++) { > + if ((offset + i) >= (*payload)->len) { > + break; > + } > + tx = (tx << 8) | read_buf[i]; > + } > + rx = ssi_transfer((sc->bus).ssi_bus, tx); > + for (int i = 0; i < 4; i++) { > + if ((offset + i) >= (*payload)->len) { > + break; > + } > + *(xfer_buffer_write_ptr(rsp_payload, rsp_payload->len, 1)) = > + (rx >> (24 - i * 8)) & 0xFF; > + } > + } > + if (rsp_payload != NULL) { > + spi_response(sc, sc->N1_bits, rsp_payload); > + } > + sc->first = 0; > + sc->last = 0; > + /* The N1 frame shift is complete so reset the N1 counters */ > + sc->N2_bits = 0; > + sc->N2_bytes = 0; > + sc->N2_tx = 0; > + sc->N2_rx = 0; > + xfer_buffer_free(*payload); > + *payload = NULL; > + SPI_DEBUG(qemu_log("Payload buffer freed\n")); > + } else { > + SPI_DEBUG(qemu_log("Not shifting N1, send_n1_alone = %d, stop = %d\n", > + send_n1_alone, stop)); > + } > + return stop; > +} /* end of operation_shiftn1() */ > + > +/* > + * Calculate the N2 counters based on passed in opcode and > + * internal register values. > + * The method assumes that the opcode is a Shift_N2 opcode > + * and doesn't test it. > + * The counters returned are: > + * N2 bits: Number of bits in the payload data that are significant > + * to the responder. > + * N2_bytes: Total count of payload bytes for the N2 frame. > + * N2_tx: Total number of bytes taken from TDR for N2 > + * N2_rx: Total number of bytes taken from the payload for N2 > + */ > +void calculate_N2(PnvSpiController *sc, uint8_t opcode) > +{ > + /* > + * Shift_N2 opcode form: 0x4M > + * Implicit mode: > + * If M!=0 the shift count is M bytes and M is the number of rx bytes. > + * Forced Implicit mode: > + * M is the shift count but tx and rx is determined by the count control > + * register fields. Note that we only check for Forced Implicit mode when > + * M != 0 since the mode doesn't make sense when M = 0. > + * Explicit mode: > + * If M==0 then shift count is number of bits defined in the > + * Counter Configuration Register's shift_count_N1 field. > + */ > + if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) { > + /* Explicit mode */ > + sc->N2_bits = GETFIELD(COUNTER_CONFIG_REG_SHIFT_COUNT_N2, > + sc->counter_config_reg); > + sc->N2_bytes = ceil(sc->N2_bits / 8); > + sc->N2_tx = 0; > + sc->N2_rx = 0; > + /* If tx count control for N2 is set, load the tx value */ > + if (GETFIELD(PPC_BIT(54), sc->counter_config_reg) == 1) { > + sc->N2_tx = sc->N2_bytes; > + } > + /* If rx count control for N2 is set, load the rx value */ > + if (GETFIELD(PPC_BIT(55), sc->counter_config_reg) == 1) { > + sc->N2_rx = sc->N2_bytes; > + } > + } else { > + /* Implicit mode/Forced Implicit mode, use M field from opcode */ > + sc->N2_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode); > + sc->N2_bits = sc->N2_bytes * 8; > + /* Assume that we are going to receive the count */ > + sc->N2_rx = sc->N2_bytes; > + sc->N2_tx = 0; > + /* Let Forced Implicit mode have an effect on the counts */ > + if (GETFIELD(PPC_BIT(53), sc->counter_config_reg) == 1) { > + /* > + * If Forced Implicit mode and count control doesn't > + * indicate a receive then reset the rx count to 0 > + */ > + if (GETFIELD(PPC_BIT(55), sc->counter_config_reg) == 0) { > + sc->N2_rx = 0; > + } > + /* If tx count control for N2 is set, load the tx value */ > + if (GETFIELD(PPC_BIT(54), sc->counter_config_reg) == 1) { > + sc->N2_tx = sc->N2_bytes; > + } > + } > + } > + /* > + * Enforce an upper limit on the size of N1 that is equal to the > + * known size of the shift register, 64 bits or 72 bits if ECC > + * is enabled. > + * If the size exceeds 72 bits it is a user error so log an error, > + * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM > + * error bit. > + */ > + uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30), > + sc->clock_config_reset_control); > + if (ecc_control == 0 || ecc_control == 2) { > + if (sc->N2_bytes > (SPI_CONTROLLER_REG_SIZE + 1)) { > + SPI_DEBUG(qemu_log("Unsupported N2 shift size when ECC enabled, " > + "bytes = 0x%x, bits = 0x%x\n", > + sc->N2_bytes, sc->N2_bits)); > + sc->N2_bytes = SPI_CONTROLLER_REG_SIZE + 1; > + sc->N2_bits = sc->N2_bytes * 8; > + } > + } else if (sc->N2_bytes > SPI_CONTROLLER_REG_SIZE) { > + SPI_DEBUG(qemu_log("Unsupported N2 shift size, bytes = 0x%x, " > + "bits = 0x%x\n", sc->N2_bytes, sc->N2_bits)); > + sc->N2_bytes = SPI_CONTROLLER_REG_SIZE; > + sc->N2_bits = sc->N2_bytes * 8; > + } > +} /* end of calculate_N2 */ > + > +/* > + * Shift_N2 operation handler method > + */ > + > +bool operation_shiftn2(PnvSpiController *sc, uint8_t opcode, > + xfer_buffer **payload) > +{ > + uint8_t n2_count; > + bool stop = false; > + > + /* > + * If there isn't a current payload left over from a stopped sequence > + * create a new one. > + */ > + if (*payload == NULL) { > + SPI_DEBUG(qemu_log("Creating new payload xfer_buffer\n")); > + *payload = xfer_buffer_new(); > + } > + /* > + * Use a combination of N2 counters to build the N2 portion of the > + * transmit payload. > + */ > + calculate_N2(sc, opcode); > + SPI_DEBUG(qemu_log("Shift N2 started\n")); > + log_all_N_counts(sc); > + /* > + * The only difference between this code and the code for shift N1 is > + * that this code has to account for the possible presence of N1 transmit > + * bytes already taken from the TDR. > + * If there are bytes to be transmitted for the N2 portion of the frame > + * and there are still bytes in TDR that have not been copied into the > + * TX data of the payload, this code will handle transmitting those > + * remaining bytes. > + * If for some reason the transmit count(s) add up to more than the size > + * of the TDR we will just append 0xFF to the transmit payload data until > + * the payload is N1 + N2 bytes long. > + */ > + n2_count = 0; > + while (n2_count < sc->N2_bytes) { > + /* > + * If the RDR is full and we need to RX just bail out, letting the > + * code continue will end up building the payload twice in the same > + * buffer since RDR full causes a sequence stop and restart. > + */ > + if ((sc->N2_rx != 0) && > + (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1)) { > + SPI_DEBUG(qemu_log("Shift N2 set for receive but RDR is full, " > + "requesting sequencer stop\n")); > + stop = true; > + break; > + } > + if ((sc->N2_tx != 0) && ((sc->N1_tx + n2_count) < > + SPI_CONTROLLER_REG_SIZE)) { > + /* Always append data for the N2 segment if it is set for TX */ > + uint8_t n2_byte = 0x00; > + n2_byte = get_from_offset(sc, (sc->N1_tx + n2_count)); > + SPI_DEBUG(qemu_log("Extracting tx n2_byte = 0x%2.2x at index %d " > + "from TDR\n", n2_byte, (sc->N1_tx + n2_count))); > + if (sc->reverse_bits) { > + SPI_DEBUG(qemu_log("Reversing bit order of tx n2_byte\n")); > + n2_byte = reverse_bits8(n2_byte); > + } > + SPI_DEBUG(qemu_log("Appending tx n2_byte = 0x%2.2x to Payload\n", > + n2_byte)); > + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = n2_byte; > + } else { > + /* > + * Regardless of whether or not N2 is set for TX or RX, we need > + * the number of bytes in the payload to match the overall length > + * of the operation. > + */ > + SPI_DEBUG(qemu_log("Appending tx n2_byte = 0xFF to Payload\n")); > + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = 0xff; > + } > + n2_count++; > + } /* end of while */ > + if (!stop) { > + uint32_t tx; > + uint32_t rx; > + uint8_t *read_buf = NULL; > + xfer_buffer *rsp_payload = NULL; > + > + /* We have a TX and a full TDR or an RX and an empty RDR */ > + SPI_DEBUG(qemu_log("Shifting N2 frame: first = %d, last = %d, " > + "n1+n2 bits = %d\n", sc->first, sc->last, > + (sc->N1_bits + sc->N2_bits))); > + rsp_payload = xfer_buffer_new(); > + for (int offset = 0; offset < (*payload)->len; offset = offset + 4) { > + xfer_buffer_read_ptr(*payload, &read_buf, offset, 4); > + tx = 0; > + for (int i = 0; i < 4; i++) { > + if ((offset + i) >= (*payload)->len) { > + break; > + } > + tx = (tx << 8) | read_buf[i]; > + } > + rx = ssi_transfer((sc->bus).ssi_bus, tx); > + for (int i = 0; i < 4; i++) { > + if ((offset + i) >= (*payload)->len) { > + break; > + } > + *(xfer_buffer_write_ptr(rsp_payload, rsp_payload->len, 1)) = > + (rx >> (24 - i * 8)) & 0xFF; > + } > + } > + if (rsp_payload != NULL) { > + spi_response(sc, (sc->N1_bits + sc->N2_bits), rsp_payload); > + } > + sc->first = 0; > + sc->last = 0; > + /* > + * If we are doing an N2 TX and the TDR is full we need to clear the > + * TDR_full status. Do this here instead of up in the loop above so we > + * don't log the message in every loop iteration. > + */ > + if ((sc->N2_tx != 0) && > + (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1)) { > + sc->status_reg = SETFIELD(STATUS_REG_TDR_FULL, sc->status_reg, 0); > + SPI_DEBUG(qemu_log("TDR_full set to 0\n")); > + } > + /* > + * The N2 frame shift is complete so reset the N2 counters. > + * Reset the N1 counters also in case the frame was a combination of > + * N1 and N2 segments. > + */ > + sc->N2_bits = 0; > + sc->N2_bytes = 0; > + sc->N2_tx = 0; > + sc->N2_rx = 0; > + sc->N1_bits = 0; > + sc->N1_bytes = 0; > + sc->N1_tx = 0; > + sc->N1_rx = 0; > + xfer_buffer_free(*payload); > + *payload = NULL; > + SPI_DEBUG(qemu_log("Payload buffer freed\n")); > + } else { > + SPI_DEBUG(qemu_log("Not shifting N2, stop = %d\n", stop)); > + } > + return stop; > +} /* end of operation_shiftn2()*/ > + > +/* > + * The SPIC engine and its internal sequencer can be interrupted and reset by > + * a hardware signal, the sbe_spicst_hard_reset bits from Pervasive > + * Miscellaneous Register of sbe_register_bo device. > + * Reset immediately aborts any SPI transaction in progress and returns the > + * sequencer and state machines to idle state. > + * The configuration register values are not changed. The status register is > + * not reset. The engine registers are not reset. > + * The SPIC engine reset does not have any affect on the attached devices. > + * Reset handling of any attached devices is beyond the scope of the engine. > + */ > +static void do_reset(DeviceState *dev) > +{ > + PnvSpiController *sc = PNV_SPICONTROLLER(dev); > + SPI_DEBUG(qemu_log("Resetting spic engine sequencer configuration and spi " > + "communication\n")); > + /* Reset all N1 and N2 counters, and other constants */ > + sc->first = 0; > + sc->last = 0; > + sc->N2_bits = 0; > + sc->N2_bytes = 0; > + sc->N2_tx = 0; > + sc->N2_rx = 0; > + sc->N1_bits = 0; > + sc->N1_bytes = 0; > + sc->N1_tx = 0; > + sc->N1_rx = 0; > + sc->loop_counter_1 = 0; > + sc->loop_counter_2 = 0; > + SPI_DEBUG(qemu_log("Disconnected from responder\n")); > + qemu_set_irq((sc->bus).cs_line[0], 1); > +} > + > static void pnv_spi_bus_realize(DeviceState *dev, Error **errp) > { > PnvSPIBus *s = PNV_SPI_BUS(dev); > @@ -191,6 +1498,7 @@ static const TypeInfo pnv_spi_bus_info = { > > static Property pnv_spi_controller_properties[] = { > DEFINE_PROP_UINT32("spic_num", PnvSpiController, spic_num, 0), > + DEFINE_PROP_BOOL("reverse_bits", PnvSpiController, reverse_bits, false), > DEFINE_PROP_END_OF_LIST(), > }; > > @@ -254,6 +1562,7 @@ static void pnv_spi_controller_class_init(ObjectClass *klass, void *data) > > dc->desc = "PowerNV SPI Controller"; > dc->realize = pnv_spi_controller_realize; > + dc->reset = do_reset; > device_class_set_props(dc, pnv_spi_controller_properties); > } >
On 16-04-2024 15:09, Cédric Le Goater wrote: > Hello, > > Please rephrase the subject to something like: > > "ppc/pnv: Extend SPI model ..." > > Using a verb is preferable. Sure. Will update. Thank You. > > On 4/9/24 19:56, Chalapathi V wrote: >> In this commit SPI shift engine and sequencer logic is implemented. >> Shift engine performs serialization and de-serialization according to >> the >> control by the sequencer and according to the setup defined in the >> configuration registers. Sequencer implements the main control logic and >> FSM to handle data transmit and data receive control of the shift >> engine. >> >> Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com> >> --- >> include/hw/ppc/pnv_spi_controller.h | 72 ++ >> hw/ppc/pnv_spi_controller.c | 1311 ++++++++++++++++++++++++++- >> 2 files changed, 1382 insertions(+), 1 deletion(-) >> >> diff --git a/include/hw/ppc/pnv_spi_controller.h >> b/include/hw/ppc/pnv_spi_controller.h >> index 5ec50fb14c..ee8e7a17da 100644 >> --- a/include/hw/ppc/pnv_spi_controller.h >> +++ b/include/hw/ppc/pnv_spi_controller.h >> @@ -8,6 +8,14 @@ >> * This model Supports a connection to a single SPI responder. >> * Introduced for P10 to provide access to SPI seeproms, TPM, flash >> device >> * and an ADC controller. >> + * >> + * All SPI function control is mapped into the SPI register space to >> enable >> + * full control by firmware. >> + * >> + * SPI Controller has sequencer and shift engine. The SPI shift engine >> + * performs serialization and de-serialization according to the >> control by >> + * the sequencer and according to the setup defined in the >> configuration >> + * registers and the SPI sequencer implements the main control logic. >> */ >> #include "hw/ssi/ssi.h" >> @@ -21,6 +29,7 @@ >> #define SPI_CONTROLLER_REG_SIZE 8 >> typedef struct SSIBus SSIBus; >> +typedef struct xfer_buffer xfer_buffer; > > Please use CamelCase names for typedef. The forward declaration doesn't > seem useful. Sure. Will remove and test. > >> #define TYPE_PNV_SPI_BUS "pnv-spi-bus" >> OBJECT_DECLARE_SIMPLE_TYPE(PnvSPIBus, PNV_SPI_BUS) >> @@ -33,6 +42,21 @@ typedef struct PnvSPIBus { >> uint32_t id; >> } PnvSPIBus; >> +/* xfer_buffer */ >> +typedef struct xfer_buffer { >> + >> + uint32_t len; >> + uint8_t *data; >> + >> +} xfer_buffer; >> + >> +uint8_t *xfer_buffer_write_ptr(xfer_buffer *payload, uint32_t offset, >> + uint32_t length); >> +void xfer_buffer_read_ptr(xfer_buffer *payload, uint8_t **read_buf, >> + uint32_t offset, uint32_t length); >> +xfer_buffer *xfer_buffer_new(void); >> +void xfer_buffer_free(xfer_buffer *payload); >> + > > I don't think these helper routines need to be defined in the header file > of the PnvPsi model. They look internal to me. Sure. Will move them. > >> typedef struct PnvSpiController { >> DeviceState parent; >> @@ -40,6 +64,39 @@ typedef struct PnvSpiController { >> MemoryRegion xscom_spic_regs; >> /* SPI controller object number */ >> uint32_t spic_num; >> + uint8_t responder_select; >> + /* To verify if shift_n1 happens prior to shift_n2 */ >> + bool shift_n1_done; >> + /* >> + * Internal flags for the first and last indicators for the SPI >> + * interface methods >> + */ >> + uint8_t first; >> + uint8_t last; >> + /* Loop counter for branch operation opcode Ex/Fx */ >> + uint8_t loop_counter_1; >> + uint8_t loop_counter_2; >> + /* N1/N2_bits specifies the size of the N1/N2 segment of a frame >> in bits.*/ >> + uint8_t N1_bits; >> + uint8_t N2_bits; >> + /* Number of bytes in a payload for the N1/N2 frame segment.*/ >> + uint8_t N1_bytes; >> + uint8_t N2_bytes; >> + /* Number of N1/N2 bytes marked for transmit */ >> + uint8_t N1_tx; >> + uint8_t N2_tx; >> + /* Number of N1/N2 bytes marked for receive */ >> + uint8_t N1_rx; >> + uint8_t N2_rx; >> + /* >> + * Setting this attribute to true will cause the engine to >> reverse the >> + * bit order of each byte it appends to a payload before sending >> the >> + * payload to a device. There may be cases where an end device >> expects >> + * a reversed order, like in the case of the Nuvoton TPM device. >> The >> + * order of bytes in the payload is not reversed, only the order >> of the >> + * 8 bits in each payload byte. >> + */ >> + bool reverse_bits; >> /* SPI Controller registers */ >> uint64_t error_reg; >> @@ -52,4 +109,19 @@ typedef struct PnvSpiController { >> uint8_t sequencer_operation_reg[SPI_CONTROLLER_REG_SIZE]; >> uint64_t status_reg; >> } PnvSpiController; >> + >> +void log_all_N_counts(PnvSpiController *spi_controller); >> +void spi_response(PnvSpiController *spi_controller, int bits, >> + xfer_buffer *rsp_payload); >> +void operation_sequencer(PnvSpiController *spi_controller); >> +bool operation_shiftn1(PnvSpiController *spi_controller, uint8_t >> opcode, >> + xfer_buffer **payload, bool send_n1_alone); >> +bool operation_shiftn2(PnvSpiController *spi_controller, uint8_t >> opcode, >> + xfer_buffer **payload); >> +bool does_rdr_match(PnvSpiController *spi_controller); >> +uint8_t get_from_offset(PnvSpiController *spi_controller, uint8_t >> offset); >> +void shift_byte_in(PnvSpiController *spi_controller, uint8_t byte); >> +void calculate_N1(PnvSpiController *spi_controller, uint8_t opcode); >> +void calculate_N2(PnvSpiController *spi_controller, uint8_t opcode); >> +uint8_t reverse_bits8(uint8_t x); > > These routines are internal and belong to hw/ppc/pnv_spi_controller.c. > Please > don't export them. Also, adding a pnv_psi_ prefix would be a plus to > identify > the sympbols. Will move them to pnv_spi_controller.c. Thank You. > > >> #endif /* PPC_PNV_SPI_CONTROLLER_H */ >> diff --git a/hw/ppc/pnv_spi_controller.c b/hw/ppc/pnv_spi_controller.c >> index e2478a47f2..afe7f17565 100644 >> --- a/hw/ppc/pnv_spi_controller.c >> +++ b/hw/ppc/pnv_spi_controller.c >> @@ -52,6 +52,11 @@ static uint64_t pnv_spi_controller_read(void >> *opaque, hwaddr addr, >> val)); >> sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, >> sc->status_reg, 0); >> SPI_DEBUG(qemu_log("RDR being read, RDR_full set to 0\n")); >> + if (GETFIELD(STATUS_REG_SHIFTER_FSM, sc->status_reg) == >> FSM_WAIT) { >> + SPI_DEBUG(qemu_log("RDR being read while shifter is >> waiting, " >> + "starting sequencer\n")); > > Please use trace events instead. Sure, will update. > >> + operation_sequencer(sc); >> + } >> break; >> case SEQUENCER_OPERATION_REG: >> val = 0; >> @@ -124,13 +129,15 @@ static void pnv_spi_controller_write(void >> *opaque, hwaddr addr, >> sc->status_reg = SETFIELD(STATUS_REG_TDR_UNDERRUN, >> sc->status_reg, 0); >> SPI_DEBUG(qemu_log("TDR being written, TDR_underrun set to >> 0\n")); >> SPI_DEBUG(qemu_log("TDR being written, starting >> sequencer\n")); >> + operation_sequencer(sc); >> + >> break; >> case RECEIVE_DATA_REG: >> sc->receive_data_reg = val; >> break; >> case SEQUENCER_OPERATION_REG: >> for (int i = 0; i < SPI_CONTROLLER_REG_SIZE; i++) { >> - sc->sequencer_operation_reg[i] = (val >> (56 - i * 8)) & 0xFF; >> + sc->sequencer_operation_reg[i] = (val >> (56 - i * 8)) & >> 0xFF; > > This change belongs to the previous patch. Yes, Thank you for catching. will update in v3. > >> } >> break; >> case STATUS_REG: >> @@ -157,6 +164,1306 @@ static const MemoryRegionOps >> pnv_spi_controller_xscom_ops = { >> .endianness = DEVICE_BIG_ENDIAN, >> }; >> +/* xfer_buffer_methods */ >> +xfer_buffer *xfer_buffer_new(void) >> +{ >> + xfer_buffer *payload = g_malloc0(sizeof(*payload)); >> + >> + payload->data = g_malloc0(payload->len); > > euh. payload->len is 0. This allocation is pointless. > >> + return payload; >> +} >> + >> +void xfer_buffer_free(xfer_buffer *payload) >> +{ >> + free(payload->data); >> + free(payload); >> +} >> + >> +uint8_t *xfer_buffer_write_ptr(xfer_buffer *payload, uint32_t offset, >> + uint32_t length) >> +{ >> + if (payload->len < (offset + length)) { >> + payload->len = offset + length; >> + payload->data = g_realloc(payload->data, payload->len); >> + } >> + return &payload->data[offset]; >> +} >> + >> +void xfer_buffer_read_ptr(xfer_buffer *payload, uint8_t **read_buf, >> + uint32_t offset, uint32_t length) >> +{ >> + static uint32_t prev_len; >> + if ((prev_len != length) || (*read_buf == NULL)) { >> + *read_buf = g_realloc(*read_buf, length); >> + prev_len = length; >> + } >> + if (offset > payload->len) { >> + /* Reading outside payload, just return */ >> + return; >> + } >> + *read_buf = &payload->data[offset]; >> +} > > Isn't there a maximum buffer size ? It would simplify the implementation > and avoid all these alloc/realloc/free calls. Will check and rework on this. Thank You. > >> +uint8_t reverse_bits8(uint8_t x) >> +{ >> + x = (x << 4) | (x >> 4); >> + x = ((x & 0x33) << 2) | ((x & 0xcc) >> 2); >> + x = ((x & 0x55) << 1) | ((x & 0xaa) >> 1); >> + return x; >> +} > > revbit8() in qemu/host-utils.h should do the same. > > The rest is difficult to comment on without an intimitate knowledge of > the controller and the datasheet. Can teammates help ? > > Thanks, > > C. > > > >> +bool does_rdr_match(PnvSpiController *sc) >> +{ >> + /* >> + * According to spec, the mask bits that are 0 are compared and the >> + * bits that are 1 are ignored. >> + */ >> + uint16_t rdr_match_mask = >> GETFIELD(MEMORY_MAPPING_REG_RDR_MATCH_MASK, >> + sc->memory_mapping_reg); >> + uint16_t rdr_match_val = GETFIELD(MEMORY_MAPPING_REG_RDR_MATCH_VAL, >> + sc->memory_mapping_reg); >> + if ((~rdr_match_mask & rdr_match_val) == ((~rdr_match_mask) & >> + GETFIELD(PPC_BITMASK(48, 63), sc->receive_data_reg))) { >> + SPI_DEBUG(qemu_log("RDR match successful, match=0x%4.4x, " >> + "mask=0x%4.4x, >> RDR[48:63]=0x%4.4llx\n", >> + rdr_match_val, rdr_match_mask, >> + GETFIELD(PPC_BITMASK(48, 63), >> + sc->receive_data_reg))); >> + return true; >> + } else { >> + SPI_DEBUG(qemu_log("RDR match failed, match=0x%4.4x, >> mask=0x%4.4x, " >> + "RDR[48:63]=0x%4.4llx\n", rdr_match_val, rdr_match_mask, >> + GETFIELD(PPC_BITMASK(48, 63), sc->receive_data_reg))); >> + return false; >> + } >> +} >> + >> +uint8_t get_from_offset(PnvSpiController *sc, uint8_t offset) >> +{ >> + uint8_t byte; >> + >> + /* >> + * Offset is an index between 0 and SPI_CONTROLLER_REG_SIZE - 1 >> + * Check the offset before using it. >> + */ >> + if (offset < SPI_CONTROLLER_REG_SIZE) { >> + byte = (sc->transmit_data_reg >> (56 - offset * 8)) & 0xFF; >> + } else { >> + /* >> + * Log an error and return a 0xFF since we have to assign >> something >> + * to byte before returning. >> + */ >> + qemu_log_mask(LOG_GUEST_ERROR, "Invalid offset = %d used to >> get byte " >> + "from TDR\n", offset); >> + byte = 0xff; >> + } >> + return byte; >> +} >> + >> +void shift_byte_in(PnvSpiController *sc, uint8_t byte) >> +{ >> + sc->receive_data_reg = (sc->receive_data_reg << 8) | byte; >> + SPI_DEBUG(qemu_log("0x%2.2x shifted in, RDR now = 0x%16.16lx\n", >> byte, >> + sc->receive_data_reg)); >> +} >> + >> +void spi_response(PnvSpiController *sc, int bits, xfer_buffer >> *rsp_payload) >> +{ >> + uint8_t *read_buf = NULL; >> + uint8_t ecc_count; >> + uint8_t shift_in_count; >> + >> + /* >> + * Processing here must handle: >> + * - Which bytes in the payload we should move to the RDR >> + * - Explicit mode counter configuration settings >> + * - RDR full and RDR overrun status >> + */ >> + >> + /* >> + * First check that the response payload is the exact same >> + * number of bytes as the request payload was >> + */ >> + if (rsp_payload->len != (sc->N1_bytes + sc->N2_bytes)) { >> + qemu_log_mask(LOG_GUEST_ERROR, "Invalid response payload >> size in " >> + "bytes, expected %d, got %d\n", >> + (sc->N1_bytes + sc->N2_bytes), >> rsp_payload->len); >> + } else { >> + uint8_t ecc_control; >> + SPI_DEBUG(qemu_log("SPI response received, payload len = %d\n", >> + rsp_payload->len)); >> + log_all_N_counts(sc); >> + /* >> + * Adding an ECC count let's us know when we have found a >> payload byte >> + * that was shifted in but cannot be loaded into RDR. Bits >> 29-30 >> + * equal to either 0b00 or 0b10 indicate that we are taking >> in data >> + * with ECC and either applying the ECC or discarding it. >> + */ >> + ecc_count = 0; >> + ecc_control = GETFIELD(PPC_BITMASK(29, 30), >> + sc->clock_config_reset_control); >> + if (ecc_control == 0 || ecc_control == 2) { >> + ecc_count = 1; >> + } >> + /* >> + * Use the N1_rx and N2_rx counts to control shifting data >> from the >> + * payload into the RDR. Keep an overall count of the >> number of bytes >> + * shifted into RDR so we can discard every 9th byte when >> ECC is >> + * enabled. >> + */ >> + shift_in_count = 0; >> + /* Handle the N1 portion of the frame first */ >> + if (sc->N1_rx != 0) { >> + uint8_t n1_count = 0; >> + while (n1_count < sc->N1_bytes) { >> + shift_in_count++; >> + xfer_buffer_read_ptr(rsp_payload, &read_buf, >> n1_count, 1); >> + if ((ecc_count != 0) && >> + (shift_in_count == (SPI_CONTROLLER_REG_SIZE + >> ecc_count))) { >> + SPI_DEBUG(qemu_log("Discarding rx N1 ECC byte = >> 0x%2.2x at " >> + "payload index = %d\n", read_buf[0], >> n1_count)); >> + shift_in_count = 0; >> + } else { >> + uint8_t n1_byte = 0x00; >> + n1_byte = read_buf[0]; >> + SPI_DEBUG(qemu_log("Extracting rx n1_byte = >> 0x%2.2x from " >> + "payload at index = %d\n", n1_byte, >> n1_count)); >> + if (sc->reverse_bits) { >> + SPI_DEBUG(qemu_log("Reversing bit order of rx " >> + "n1_byte\n")); >> + n1_byte = reverse_bits8(n1_byte); >> + } >> + SPI_DEBUG(qemu_log("Shifting rx N1 byte = >> 0x%2.2x into " >> + "RDR\n", n1_byte)); >> + shift_byte_in(sc, n1_byte); >> + } >> + n1_count++; >> + } /* end of while */ >> + } >> + /* Handle the N2 portion of the frame */ >> + if (sc->N2_rx != 0) { >> + uint8_t n2_count = 0; >> + while (n2_count < sc->N2_bytes) { >> + shift_in_count++; >> + xfer_buffer_read_ptr(rsp_payload, &read_buf, >> + (sc->N1_bytes + n2_count), 1); >> + if ((ecc_count != 0) && >> + (shift_in_count == (SPI_CONTROLLER_REG_SIZE + >> ecc_count))) { >> + SPI_DEBUG(qemu_log("Discarding rx N1 ECC byte = >> 0x%2.2x at " >> + "payload index = %d\n", read_buf[0], >> + (sc->N1_bytes + n2_count))); >> + shift_in_count = 0; >> + } else { >> + /* >> + * The code handles shifting data from the >> payload received >> + * from the responder into the responder's RDR. >> Since this >> + * is an N2 frame segment it is safe to assume >> that there >> + * was a preceding N1 segment which was combined >> with an N2 >> + * segment to create a single frame. The >> response data will >> + * then have N1_bytes of data in the payload >> representing a >> + * responder response to the N1 section of the >> frame. If N2 >> + * is set to receive the shifting for N2 data >> begins after >> + * the N1 bytes regardless of whether or not N1 >> was marked >> + * for transmit or receive. >> + */ >> + uint8_t n2_byte = 0x00; >> + n2_byte = read_buf[0]; >> + SPI_DEBUG(qemu_log("Extracting rx n2_byte = >> 0x%2.2x from " >> + "payload at index = %d\n", n2_byte, >> + (sc->N1_bytes + n2_count))); >> + if (sc->reverse_bits) { >> + SPI_DEBUG(qemu_log("Reversing bit order of rx " >> + "n2_byte\n")); >> + n2_byte = reverse_bits8(n2_byte); >> + } >> + SPI_DEBUG(qemu_log("Shifting rx N2 byte = >> 0x%2.2x into " >> + "RDR\n", n2_byte)); >> + shift_byte_in(sc, n2_byte); >> + } >> + n2_count++; >> + } >> + } >> + if ((sc->N1_rx + sc->N2_rx) > 0) { >> + /* >> + * Data was received so handle RDR status. >> + * It is easier to handle RDR_full and RDR_overrun >> status here >> + * since the RDR register's shift_byte_in method is called >> + * multiple times in a row. Controlling RDR status is >> done here >> + * instead of in the RDR scoped methods for that reason. >> + */ >> + if (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1) { >> + /* >> + * Data was shifted into the RDR before having been >> read >> + * causing previous data to have been overrun. >> + */ >> + sc->status_reg = SETFIELD(STATUS_REG_RDR_OVERRUN, >> + sc->status_reg, 1); >> + } else { >> + /* >> + * Set status to indicate that the received data >> register is >> + * full. This flag is only cleared once the RDR is >> unloaded. >> + */ >> + sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, >> + sc->status_reg, 1); >> + SPI_DEBUG(qemu_log("RDR_full set to 1\n")); >> + } >> + } >> + } /* end of else */ >> +} /* end of spi_response() */ >> + >> +void log_all_N_counts(PnvSpiController *sc) >> +{ >> + SPI_DEBUG(qemu_log("N1_bits = %d, N1_bytes = %d, N1_tx = %d, >> N1_rx = %d, " >> + "N2_bits = %d, N2_bytes = %d, N2_tx = %d, N2_rx = %d\n", >> + sc->N1_bits, sc->N1_bytes, sc->N1_tx, sc->N1_rx, >> sc->N2_bits, >> + sc->N2_bytes, sc->N2_tx, sc->N2_rx)); >> +} >> + >> +static inline void next_sequencer_fsm(PnvSpiController *sc) >> +{ >> + uint8_t seq_index = GETFIELD(STATUS_REG_SEQUENCER_INDEX, >> sc->status_reg); >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> sc->status_reg, >> + (seq_index + 1)); >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg, >> + SEQ_STATE_INDEX_INCREMENT); >> +} >> + >> +void operation_sequencer(PnvSpiController *sc) >> +{ >> + /* >> + * Loop through each sequencer operation ID and perform the >> requested >> + * operations. >> + * Flag for indicating if we should send the N1 frame or wait to >> combine >> + * it with a preceding N2 frame. >> + */ >> + bool send_n1_alone = true; >> + bool stop = false; /* Flag to stop the sequencer */ >> + uint8_t opcode = 0; >> + uint8_t masked_opcode = 0; >> + >> + /* >> + * xfer_buffer for containing the payload of the SPI frame. >> + * This is a static because there are cases where a sequence has >> to stop >> + * and wait for the target application to unload the RDR. If >> this occurs >> + * during a sequence where N1 is not sent alone and instead >> combined with >> + * N2 since the N1 tx length + the N2 tx length is less than the >> size of >> + * the TDR. >> + */ >> + static xfer_buffer *payload; >> + >> + if (payload == NULL) { >> + payload = xfer_buffer_new(); >> + } >> + /* >> + * Clear the sequencer FSM error bit - general_SPI_status[3] >> + * before starting a sequence. >> + */ >> + sc->status_reg = SETFIELD(PPC_BIT(35), sc->status_reg, 0); >> + /* >> + * If the FSM is idle set the sequencer index to 0 >> + * (new/restarted sequence) >> + */ >> + if (GETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg) == >> + SEQ_STATE_IDLE) { >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg, 0); >> + } >> + /* >> + * There are only 8 possible operation IDs to iterate through >> though >> + * some operations may cause more than one frame to be sequenced. >> + */ >> + while (GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg) < 8) { >> + opcode = sc->sequencer_operation_reg[GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, sc->status_reg)]; >> + /* Set sequencer state to decode */ >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> sc->status_reg, >> + SEQ_STATE_DECODE); >> + /* >> + * Only the upper nibble of the operation ID is needed to >> know what >> + * kind of operation is requested. >> + */ >> + masked_opcode = opcode & 0xF0; >> + switch (masked_opcode) { >> + /* >> + * Increment the operation index in each case instead of just >> + * once at the end in case an operation like the branch >> + * operation needs to change the index. >> + */ >> + case SEQ_OP_STOP: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + /* A stop operation in any position stops the sequencer */ >> + SPI_DEBUG(qemu_log("Sequencer STOP at index = 0x%llx, >> sequencer " >> + "idling\n", GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg))); >> + stop = true; >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> sc->status_reg, >> + FSM_IDLE); >> + sc->loop_counter_1 = 0; >> + sc->loop_counter_2 = 0; >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, SEQ_STATE_IDLE); >> + break; >> + >> + case SEQ_OP_SELECT_SLAVE: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + SPI_DEBUG(qemu_log("Sequencer SELECT_SLAVE at index = >> 0x%llx\n", >> + GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); >> + /* >> + * This device currently only supports a single responder >> + * connection at position 0. De-selecting a responder >> is fine >> + * and expected at the end of a sequence but selecting any >> + * responder other than 0 should cause an error. >> + */ >> + sc->responder_select = opcode & 0x0F; >> + if (sc->responder_select == 0) { >> + SPI_DEBUG(qemu_log("Shifter done, pull the CS line >> high\n")); >> + qemu_set_irq((sc->bus).cs_line[0], 1); >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg, >> + (GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg) + 1)); >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, FSM_DONE); >> + } else if (sc->responder_select != 1) { >> + qemu_log_mask(LOG_GUEST_ERROR, "Slave selection >> other than 1 " >> + "not supported, select = 0x%x\n", >> + sc->responder_select); >> + SPI_DEBUG(qemu_log("Sequencer stop requested due to >> invalid " >> + "responder select at index = >> 0x%llx, " >> + "shifter idling\n", GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg))); >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, FSM_IDLE); >> + stop = true; >> + } else { >> + /* >> + * Only allow an FSM_START state when a responder is >> + * selected >> + */ >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, FSM_START); >> + SPI_DEBUG(qemu_log("shifter starting, pull CS line >> low\n")); >> + qemu_set_irq((sc->bus).cs_line[0], 0); >> + sc->first = 1; >> + sc->last = 0; >> + /* >> + * A Shift_N2 operation is only valid after a Shift_N1 >> + * according to the spec. The spec doesn't say if >> that means >> + * immediately after or just after at any point. We >> will track >> + * the occurrence of a Shift_N1 to enforce this >> requirement in >> + * the most generic way possible by assuming that >> the rule >> + * applies once a valid responder select has occurred. >> + */ >> + sc->shift_n1_done = false; >> + next_sequencer_fsm(sc); >> + } >> + break; >> + >> + case SEQ_OP_SHIFT_N1: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + SPI_DEBUG(qemu_log("Sequencer SHIFT_N1 at index = >> 0x%llx\n", >> + GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); >> + /* >> + * Only allow a shift_n1 when the state is not IDLE or >> DONE. >> + * In either of those two cases the sequencer is not in >> a proper >> + * state to perform shift operations because the >> sequencer has: >> + * - processed a responder deselect (DONE) >> + * - processed a stop opcode (IDLE) >> + * - encountered an error (IDLE) >> + */ >> + if ((GETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg) == FSM_IDLE) || >> + (GETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg) == FSM_DONE)) { >> + qemu_log_mask(LOG_GUEST_ERROR, "Shift_N1 not allowed >> in " >> + "shifter state = 0x%llx", GETFIELD( >> + STATUS_REG_SHIFTER_FSM, sc->status_reg)); >> + /* >> + * Set sequencer FSM error bit 3 >> (general_SPI_status[3]) >> + * in status reg. >> + */ >> + sc->status_reg = SETFIELD(PPC_BIT(35), >> sc->status_reg, 1); >> + SPI_DEBUG(qemu_log("Sequencer stop requested due to >> invalid " >> + "shifter state at index = 0x%llx\n", GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); >> + stop = true; >> + } else { >> + /* >> + * Look for the special case where there is a >> shift_n1 set for >> + * transmit and it is followed by a shift_n2 set for >> transmit >> + * AND the combined transmit length of the two >> operations is >> + * less than or equal to the size of the TDR >> register. In this >> + * case we want to use both this current shift_n1 >> opcode and the >> + * following shift_n2 opcode to assemble the frame for >> + * transmission to the responder without requiring a >> refill of >> + * the TDR between the two operations. >> + */ >> + if ((sc->sequencer_operation_reg[GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, sc->status_reg) + >> 1] & 0xF0) >> + == SEQ_OP_SHIFT_N2) { >> + SPI_DEBUG(qemu_log("Not sending N1 alone\n")); >> + send_n1_alone = false; >> + } >> + /* >> + * If the next opcode is 0x10, which deselects the >> SPI device >> + * then this is the last shift >> + */ >> + if (sc->sequencer_operation_reg[GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, sc->status_reg) + 1] == >> + SEQ_OP_SELECT_SLAVE) { >> + sc->last = 1; >> + } >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, FSM_SHIFT_N1); >> + stop = operation_shiftn1(sc, opcode, &payload, >> send_n1_alone); >> + if (stop) { >> + /* >> + * The operation code says to stop, this can >> occur if: >> + * (1) RDR is full and the N1 shift is set for >> receive >> + * (2) TDR was empty at the time of the N1 shift >> so we need >> + * to wait for data. >> + * (3) Neither 1 nor 2 are occurring and we >> aren't sending >> + * N1 alone and N2 counter reload is set (bit 0 >> of the N2 >> + * counter reload field). In this case >> TDR_underrun will >> + * will be set and the Payload has been loaded >> so it is >> + * ok to advance the sequencer. >> + */ >> + if (GETFIELD(STATUS_REG_TDR_UNDERRUN, >> sc->status_reg)) { >> + SPI_DEBUG(qemu_log("Sequencer stop requested >> due to N2 " >> + "counter reload active.\n")); >> + sc->shift_n1_done = true; >> + sc->status_reg = >> SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, >> + FSM_SHIFT_N2); >> + sc->status_reg = >> SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg, >> + (GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg) + 1)); >> + SPI_DEBUG(qemu_log("Set new sequencer index >> to = " >> + "0x%llx\n", GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg))); >> + } else { >> + /* >> + * This is case (1) or (2) so the sequencer >> needs to >> + * wait and NOT go to the next sequence yet. >> + */ >> + sc->status_reg = >> SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, FSM_WAIT); >> + } >> + } else { >> + /* Ok to move on to the next index */ >> + sc->shift_n1_done = true; >> + next_sequencer_fsm(sc); >> + } >> + } >> + break; >> + >> + case SEQ_OP_SHIFT_N2: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + SPI_DEBUG(qemu_log("Sequencer SHIFT_N2 at index = %lld\n", >> + GETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg))); >> + if (!sc->shift_n1_done) { >> + qemu_log_mask(LOG_GUEST_ERROR, "Shift_N2 is not >> allowed if a " >> + "Shift_N1 is not done, shifter state = >> 0x%llx", >> + GETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg)); >> + /* >> + * In case the sequencer actually stops if an N2 >> shift is >> + * requested before any N1 shift is done. Set >> sequencer FSM >> + * error bit 3 (general_SPI_status[3]) in status reg. >> + */ >> + sc->status_reg = SETFIELD(PPC_BIT(35), >> sc->status_reg, 1); >> + SPI_DEBUG(qemu_log("Sequencer stop requested due to >> shift_n2 " >> + "w/no shift_n1 done at index = >> 0x%llx\n", >> + GETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg))); >> + stop = true; >> + } else { >> + /* >> + * If the next opcode is 0x10, which deselects the >> SPI device >> + * then this is the last shift >> + */ >> + if (sc->sequencer_operation_reg[GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg) + 1] == SEQ_OP_SELECT_SLAVE) { >> + sc->last = 1; >> + } >> + /* Ok to do a Shift_N2 */ >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, >> FSM_SHIFT_N2); >> + stop = operation_shiftn2(sc, opcode, &payload); >> + /* >> + * If the operation code says to stop set the >> shifter state to >> + * wait and stop >> + */ >> + if (stop) { >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, FSM_WAIT); >> + } else { >> + /* Ok to move on to the next index */ >> + next_sequencer_fsm(sc); >> + } >> + } >> + break; >> + >> + case SEQ_OP_BRANCH_IFNEQ_RDR: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_RDR at " >> + "index = 0x%llx\n", GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> sc->status_reg))); >> + /* >> + * The memory mapping register RDR match value is >> compared against >> + * the 16 rightmost bytes of the RDR (potentially with >> masking). >> + * Since this comparison is performed against the >> contents of the >> + * RDR then a receive must have previously occurred >> otherwise >> + * there is no data to compare and the operation cannot be >> + * completed and will stop the sequencer until RDR full >> is set to >> + * 1. >> + */ >> + if (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1) { >> + bool rdr_matched = false; >> + rdr_matched = does_rdr_match(sc); >> + if (rdr_matched) { >> + SPI_DEBUG(qemu_log("Proceed to next sequencer >> index " >> + "(increment on RDR match)\n")); >> + /* A match occurred, increment the sequencer >> index. */ >> + next_sequencer_fsm(sc); >> + } else { >> + SPI_DEBUG(qemu_log("Proceed to sequencer >> index=0x%x " >> + "(branch on RDR match fail)\n", (opcode & >> 0x7))); >> + /* >> + * Branch the sequencer to the index coded into >> the op >> + * code. >> + */ >> + sc->status_reg = >> SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg, (opcode & 0x7)); >> + } >> + /* >> + * Regardless of where the branch ended up we want the >> + * sequencer to continue shifting so we have to clear >> + * RDR_full. >> + */ >> + sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, >> + sc->status_reg, 0); >> + } else { >> + SPI_DEBUG(qemu_log("RDR not full for 0x6x opcode! >> Stopping " >> + "sequencer.\n")); >> + stop = true; >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> + sc->status_reg, FSM_WAIT); >> + } >> + break; >> + >> + case SEQ_OP_TRANSFER_TDR: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + qemu_log_mask(LOG_GUEST_ERROR, "Transfer TDR is not >> supported\n"); >> + next_sequencer_fsm(sc); >> + break; >> + >> + case SEQ_OP_BRANCH_IFNEQ_INC_1: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_INC_1 at >> index = " >> + "0x%llx, next index = %d, >> count_compare_1 = " >> + "0x%llx, loop_counter_1 = %d\n", >> GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> sc->status_reg), >> + (opcode & 0x07), >> + GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, >> + sc->status_reg), sc->loop_counter_1)); >> + /* >> + * The spec says the loop should execute count compare + >> 1 times. >> + * However we learned from engineering that we really >> only loop >> + * count_compare times, count compare = 0 makes this op >> code a >> + * no-op >> + */ >> + if (sc->loop_counter_1 != >> + GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, >> + sc->counter_config_reg)) { >> + /* >> + * If the next opcode is 0x10, which deselects the >> SPI device >> + * and we know that the next opcode is the last one >> in the >> + * loop then the next shift is the last shift >> + */ >> + uint8_t condition1 = sc->sequencer_operation_reg[ >> + GETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg) + 1]; >> + uint8_t condition2 = >> GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, >> + sc->counter_config_reg); >> + >> + if ((condition1 == SEQ_OP_SELECT_SLAVE) && >> + ((sc->loop_counter_1 + 1) == condition2)) { >> + sc->last = 1; >> + } >> + /* >> + * Next index is the lower nibble of the branch >> operation ID, >> + * mask off all but the first three bits so we don't >> try to >> + * access beyond the sequencer_operation_reg boundary. >> + */ >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg, (opcode & >> 0x7)); >> + sc->loop_counter_1++; >> + SPI_DEBUG(qemu_log("Branching to index = %d, >> loop_counter_1 = " >> + "%d\n", (opcode & 0x7), sc->loop_counter_1)); >> + } else { >> + /* Continue to next index if loop counter is reached */ >> + next_sequencer_fsm(sc); >> + SPI_DEBUG(qemu_log("loop counter 1 achieved, next >> sequencer " >> + "index = 0x%llx\n", >> GETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg))); >> + } >> + break; >> + >> + case SEQ_OP_BRANCH_IFNEQ_INC_2: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_INC_2 at >> index = " >> + "0x%llx, next index = %d, >> count_compare_2 = " >> + "0x%llx, loop_counter_2 = %d\n", >> GETFIELD( >> + STATUS_REG_SEQUENCER_INDEX, >> sc->status_reg), >> + (opcode & 0x07), GETFIELD( >> + COUNTER_CONFIG_REG_COUNT_COMPARE2, >> + sc->status_reg), sc->loop_counter_2)); >> + /* >> + * If the next opcode is 0x10, which deselects the SPI >> device >> + * and we know that the next opcode is the last one in the >> + * loop then the next shift is the last shift >> + */ >> + uint8_t condition1 = sc->sequencer_operation_reg[ >> + GETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg) + 1]; >> + uint8_t condition2 = >> GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE2, >> + sc->counter_config_reg); >> + >> + if ((condition1 == SEQ_OP_SELECT_SLAVE) && >> + ((sc->loop_counter_2 + 1) == condition2)) { >> + sc->last = 1; >> + } >> + /* >> + * The spec says the loop should execute count compare + >> 1 times. >> + * However we learned from engineering that we really >> only loop >> + * count_compare times, count compare = 0 makes this op >> code a >> + * no-op >> + */ >> + if (sc->loop_counter_2 != condition2) { >> + /* >> + * Next index is the lower nibble of the branch >> operation ID, >> + * mask off all but the first three bits so we don't >> try to >> + * access beyond the sequencer_operation_reg boundary. >> + */ >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg, >> + (opcode & 0x7)); >> + sc->loop_counter_2++; >> + SPI_DEBUG(qemu_log("Branching to index = %d, >> loop_counter_2 " >> + "= %d", (opcode & 0x7), >> + sc->loop_counter_2)); >> + } else { >> + /* Continue to next index if loop counter is reached */ >> + next_sequencer_fsm(sc); >> + SPI_DEBUG(qemu_log("loop counter 2 achieved, next >> sequencer " >> + "index = 0x%llx\n", >> GETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg))); >> + } >> + break; >> + >> + default: >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, >> SEQ_STATE_EXECUTE); >> + qemu_log_mask(LOG_GUEST_ERROR, "Sequencer opcode 0x%x is >> not " >> + "supported\n", opcode); >> + /* Ignore unsupported operations. */ >> + next_sequencer_fsm(sc); >> + break; >> + } /* end of switch */ >> + /* >> + * If we used all 8 opcodes without seeing a 00 - STOP in >> the sequence >> + * we need to go ahead and end things as if there was a STOP >> at the >> + * end. >> + */ >> + if (GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg) == >> 8) { >> + SPI_DEBUG(qemu_log("All 8 opcodes completed, sequencer " >> + "idling\n")); >> + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, >> sc->status_reg, >> + FSM_IDLE); >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, >> + sc->status_reg, 0); >> + sc->loop_counter_1 = 0; >> + sc->loop_counter_2 = 0; >> + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, >> + sc->status_reg, SEQ_STATE_IDLE); >> + break; >> + } >> + /* Break the loop if a stop was requested */ >> + if (stop) { >> + break; >> + } >> + } /* end of while */ >> + return; >> +} /* end of operation_sequencer() */ >> + >> +/* >> + * Calculate the N1 counters based on passed in opcode and >> + * internal register values. >> + * The method assumes that the opcode is a Shift_N1 opcode >> + * and doesn't test it. >> + * The counters returned are: >> + * N1 bits: Number of bits in the payload data that are significant >> + * to the responder. >> + * N1_bytes: Total count of payload bytes for the N1 (portion of >> the) frame. >> + * N1_tx: Total number of bytes taken from TDR for N1 >> + * N1_rx: Total number of bytes taken from the payload for N1 >> + */ >> +void calculate_N1(PnvSpiController *sc, uint8_t opcode) >> +{ >> + /* >> + * Shift_N1 opcode form: 0x3M >> + * Implicit mode: >> + * If M != 0 the shift count is M bytes and M is the number of >> tx bytes. >> + * Forced Implicit mode: >> + * M is the shift count but tx and rx is determined by the count >> control >> + * register fields. Note that we only check for forced Implicit >> mode when >> + * M != 0 since the mode doesn't make sense when M = 0. >> + * Explicit mode: >> + * If M == 0 then shift count is number of bits defined in the >> + * Counter Configuration Register's shift_count_N1 field. >> + */ >> + if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) { >> + /* Explicit mode */ >> + sc->N1_bits = GETFIELD(COUNTER_CONFIG_REG_SHIFT_COUNT_N1, >> + sc->counter_config_reg); >> + sc->N1_bytes = ceil(sc->N1_bits / 8); >> + sc->N1_tx = 0; >> + sc->N1_rx = 0; >> + /* If tx count control for N1 is set, load the tx value */ >> + if (GETFIELD(PPC_BIT(50), sc->counter_config_reg) == 1) { >> + sc->N1_tx = sc->N1_bytes; >> + } >> + /* If rx count control for N1 is set, load the rx value */ >> + if (GETFIELD(PPC_BIT(51), sc->counter_config_reg) == 1) { >> + sc->N1_rx = sc->N1_bytes; >> + } >> + } else { >> + /* Implicit mode/Forced Implicit mode, use M field from >> opcode */ >> + sc->N1_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode); >> + sc->N1_bits = sc->N1_bytes * 8; >> + /* >> + * Assume that we are going to transmit the count >> + * (pure Implicit only) >> + */ >> + sc->N1_tx = sc->N1_bytes; >> + sc->N1_rx = 0; >> + /* Let Forced Implicit mode have an effect on the counts */ >> + if (GETFIELD(PPC_BIT(49), sc->counter_config_reg) == 1) { >> + /* >> + * If Forced Implicit mode and count control doesn't >> + * indicate transmit then reset the tx count to 0 >> + */ >> + if (GETFIELD(PPC_BIT(50), sc->counter_config_reg) == 0) { >> + sc->N1_tx = 0; >> + } >> + /* If rx count control for N1 is set, load the rx value */ >> + if (GETFIELD(PPC_BIT(51), sc->counter_config_reg) == 1) { >> + sc->N1_rx = sc->N1_bytes; >> + } >> + } >> + } >> + /* >> + * Enforce an upper limit on the size of N1 that is equal to the >> known size >> + * of the shift register, 64 bits or 72 bits if ECC is enabled. >> + * If the size exceeds 72 bits it is a user error so log an error, >> + * cap the size at a max of 64 bits or 72 bits and set the >> sequencer FSM >> + * error bit. >> + */ >> + uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30), >> + sc->clock_config_reset_control); >> + if (ecc_control == 0 || ecc_control == 2) { >> + if (sc->N1_bytes > (SPI_CONTROLLER_REG_SIZE + 1)) { >> + qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift >> size when " >> + "ECC enabled, bytes = 0x%x, bits = 0x%x\n", >> + sc->N1_bytes, sc->N1_bits); >> + sc->N1_bytes = SPI_CONTROLLER_REG_SIZE + 1; >> + sc->N1_bits = sc->N1_bytes * 8; >> + } >> + } else if (sc->N1_bytes > SPI_CONTROLLER_REG_SIZE) { >> + qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size, " >> + "bytes = 0x%x, bits = 0x%x\n", >> + sc->N1_bytes, sc->N1_bits); >> + sc->N1_bytes = SPI_CONTROLLER_REG_SIZE; >> + sc->N1_bits = sc->N1_bytes * 8; >> + } >> +} /* end of calculate_N1 */ >> + >> +/* >> + * Shift_N1 operation handler method >> + */ >> +bool operation_shiftn1(PnvSpiController *sc, uint8_t opcode, >> + xfer_buffer **payload, bool send_n1_alone) >> +{ >> + uint8_t n1_count; >> + bool stop = false; >> + >> + /* >> + * If there isn't a current payload left over from a stopped >> sequence >> + * create a new one. >> + */ >> + if (*payload == NULL) { >> + SPI_DEBUG(qemu_log("Creating new payload xfer_buffer\n")); >> + *payload = xfer_buffer_new(); >> + } >> + /* >> + * Use a combination of N1 counters to build the N1 portion of the >> + * transmit payload. >> + * We only care about transmit at this time since the request >> payload >> + * only represents data going out on the controller output line. >> + * Leave mode specific considerations in the calculate function >> since >> + * all we really care about are counters that tell use exactly how >> + * many bytes are in the payload and how many of those bytes to >> + * include from the TDR into the payload. >> + */ >> + calculate_N1(sc, opcode); >> + SPI_DEBUG(qemu_log("Shift N1 started..\n")); >> + log_all_N_counts(sc); >> + /* >> + * Zero out the N2 counters here in case there is no N2 >> operation following >> + * the N1 operation in the sequencer. This keeps leftover N2 >> information >> + * from interfering with spi_response logic. >> + */ >> + sc->N2_bits = 0; >> + sc->N2_bytes = 0; >> + sc->N2_tx = 0; >> + sc->N2_rx = 0; >> + /* >> + * N1_bytes is the overall size of the N1 portion of the frame >> regardless of >> + * whether N1 is used for tx, rx or both. Loop over the size to >> build a >> + * payload that is N1_bytes long. >> + * N1_tx is the count of bytes to take from the TDR and "shift" >> into the >> + * frame which means append those bytes to the payload for the >> N1 portion >> + * of the frame. >> + * If N1_tx is 0 or if the count exceeds the size of the TDR >> append 0xFF to >> + * the frame until the overall N1 count is reached. >> + */ >> + n1_count = 0; >> + while (n1_count < sc->N1_bytes) { >> + /* >> + * Assuming that if N1_tx is not equal to 0 then it is the >> same as >> + * N1_bytes. >> + */ >> + if ((sc->N1_tx != 0) && (n1_count < SPI_CONTROLLER_REG_SIZE)) { >> + >> + if (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1) { >> + /* >> + * Note that we are only appending to the payload IF >> the TDR >> + * is full otherwise we don't touch the payload >> because we are >> + * going to NOT send the payload and instead tell >> the sequencer >> + * that called us to stop and wait for a TDR write >> so we have >> + * data to load into the payload. >> + */ >> + uint8_t n1_byte = 0x00; >> + n1_byte = get_from_offset(sc, n1_count); >> + SPI_DEBUG(qemu_log("Extracting tx n1_byte = 0x%2.2x >> at index " >> + "%d from TDR\n", n1_byte, >> n1_count)); >> + if (sc->reverse_bits) { >> + SPI_DEBUG(qemu_log("Reversing bit order of tx >> n1_byte\n")); >> + n1_byte = reverse_bits8(n1_byte); >> + } >> + SPI_DEBUG(qemu_log("Appending tx n1_byte = 0x%2.2x to " >> + "Payload\n", n1_byte)); >> + *(xfer_buffer_write_ptr(*payload, (*payload)->len, >> 1)) = >> + n1_byte; >> + } else { >> + /* >> + * We hit a shift_n1 opcode TX but the TDR is empty, >> tell the >> + * sequencer to stop and break this loop. >> + */ >> + SPI_DEBUG(qemu_log("Shift N1 set for transmit but >> TDR is empty," >> + " requesting sequencer stop\n")); >> + stop = true; >> + break; >> + } >> + } else { >> + /* >> + * Cases here: >> + * - we are receiving during the N1 frame segment and >> the RDR >> + * is full so we need to stop until the RDR is read >> + * - we are transmitting and we don't care about RDR status >> + * since we won't be loading RDR during the frame >> segment. >> + * - we are receiving and the RDR is empty so we allow >> the operation >> + * to proceed. >> + */ >> + if ((sc->N1_rx != 0) && (GETFIELD(STATUS_REG_RDR_FULL, >> + sc->status_reg) == 1)) { >> + SPI_DEBUG(qemu_log("Shift N1 set for receive but RDR >> is full, " >> + "requesting sequencer stop\n")); >> + stop = true; >> + break; >> + } else { >> + SPI_DEBUG(qemu_log("Appending tx n1_byte = 0xFF to >> Payload\n")); >> + *(xfer_buffer_write_ptr(*payload, (*payload)->len, >> 1)) = 0xff; >> + } >> + } >> + n1_count++; >> + } /* end of while */ >> + /* >> + * If we are not stopping due to an empty TDR and we are doing >> an N1 TX >> + * and the TDR is full we need to clear the TDR_full status. >> + * Do this here instead of up in the loop above so we don't log >> the message >> + * in every loop iteration. >> + * Ignore the send_n1_alone flag, all that does is defer the TX >> until the N2 >> + * operation, which was found immediately after the current >> opcode. The TDR >> + * was unloaded and will be shifted so we have to clear the >> TDR_full status. >> + */ >> + if (!stop && (sc->N1_tx != 0) && >> + (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1)) { >> + >> + sc->status_reg = SETFIELD(STATUS_REG_TDR_FULL, >> sc->status_reg, 0); >> + SPI_DEBUG(qemu_log("TDR_full set to 0\n")); >> + } >> + /* >> + * There are other reasons why the shifter would stop, such as a >> TDR empty >> + * or RDR full condition with N1 set to receive. If we haven't >> stopped due >> + * to either one of those conditions then check if the >> send_n1_alone flag is >> + * equal to False, indicating the next opcode is an N2 >> operation, AND if >> + * the N2 counter reload switch (bit 0 of the N2 count control >> field) is >> + * set. This condition requires a pacing write to "kick" off >> the N2 >> + * shift which includes the N1 shift as well when send_n1_alone >> is False. >> + */ >> + if (!stop && !send_n1_alone && >> + (GETFIELD(PPC_BIT(52), sc->counter_config_reg) == 1)) { >> + SPI_DEBUG(qemu_log("N2 counter reload active, stop N1 shift, " >> + "TDR_underrun set to 1\n")); >> + stop = true; >> + sc->status_reg = SETFIELD(STATUS_REG_TDR_UNDERRUN, >> sc->status_reg, 1); >> + } >> + /* >> + * If send_n1_alone is set AND we have a full TDR then this is >> the first and >> + * last payload to send and we don't have an N2 frame segment to >> add to the >> + * payload. >> + */ >> + if (send_n1_alone && !stop) { >> + uint32_t tx; >> + uint32_t rx; >> + uint8_t *read_buf = NULL; >> + xfer_buffer *rsp_payload = NULL; >> + >> + /* We have a TX and a full TDR or an RX and an empty RDR */ >> + SPI_DEBUG(qemu_log("Shifting N1 frame: first = %d, last = %d, " >> + "n1 bits = %d\n", sc->first, sc->last, >> + sc->N1_bits)); >> + rsp_payload = xfer_buffer_new(); >> + for (int offset = 0; offset < (*payload)->len; offset = >> offset + 4) { >> + xfer_buffer_read_ptr(*payload, &read_buf, offset, 4); >> + tx = 0; >> + for (int i = 0; i < 4; i++) { >> + if ((offset + i) >= (*payload)->len) { >> + break; >> + } >> + tx = (tx << 8) | read_buf[i]; >> + } >> + rx = ssi_transfer((sc->bus).ssi_bus, tx); >> + for (int i = 0; i < 4; i++) { >> + if ((offset + i) >= (*payload)->len) { >> + break; >> + } >> + *(xfer_buffer_write_ptr(rsp_payload, >> rsp_payload->len, 1)) = >> + (rx >> (24 - i * 8)) & 0xFF; >> + } >> + } >> + if (rsp_payload != NULL) { >> + spi_response(sc, sc->N1_bits, rsp_payload); >> + } >> + sc->first = 0; >> + sc->last = 0; >> + /* The N1 frame shift is complete so reset the N1 counters */ >> + sc->N2_bits = 0; >> + sc->N2_bytes = 0; >> + sc->N2_tx = 0; >> + sc->N2_rx = 0; >> + xfer_buffer_free(*payload); >> + *payload = NULL; >> + SPI_DEBUG(qemu_log("Payload buffer freed\n")); >> + } else { >> + SPI_DEBUG(qemu_log("Not shifting N1, send_n1_alone = %d, >> stop = %d\n", >> + send_n1_alone, stop)); >> + } >> + return stop; >> +} /* end of operation_shiftn1() */ >> + >> +/* >> + * Calculate the N2 counters based on passed in opcode and >> + * internal register values. >> + * The method assumes that the opcode is a Shift_N2 opcode >> + * and doesn't test it. >> + * The counters returned are: >> + * N2 bits: Number of bits in the payload data that are significant >> + * to the responder. >> + * N2_bytes: Total count of payload bytes for the N2 frame. >> + * N2_tx: Total number of bytes taken from TDR for N2 >> + * N2_rx: Total number of bytes taken from the payload for N2 >> + */ >> +void calculate_N2(PnvSpiController *sc, uint8_t opcode) >> +{ >> + /* >> + * Shift_N2 opcode form: 0x4M >> + * Implicit mode: >> + * If M!=0 the shift count is M bytes and M is the number of rx >> bytes. >> + * Forced Implicit mode: >> + * M is the shift count but tx and rx is determined by the count >> control >> + * register fields. Note that we only check for Forced Implicit >> mode when >> + * M != 0 since the mode doesn't make sense when M = 0. >> + * Explicit mode: >> + * If M==0 then shift count is number of bits defined in the >> + * Counter Configuration Register's shift_count_N1 field. >> + */ >> + if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) { >> + /* Explicit mode */ >> + sc->N2_bits = GETFIELD(COUNTER_CONFIG_REG_SHIFT_COUNT_N2, >> + sc->counter_config_reg); >> + sc->N2_bytes = ceil(sc->N2_bits / 8); >> + sc->N2_tx = 0; >> + sc->N2_rx = 0; >> + /* If tx count control for N2 is set, load the tx value */ >> + if (GETFIELD(PPC_BIT(54), sc->counter_config_reg) == 1) { >> + sc->N2_tx = sc->N2_bytes; >> + } >> + /* If rx count control for N2 is set, load the rx value */ >> + if (GETFIELD(PPC_BIT(55), sc->counter_config_reg) == 1) { >> + sc->N2_rx = sc->N2_bytes; >> + } >> + } else { >> + /* Implicit mode/Forced Implicit mode, use M field from >> opcode */ >> + sc->N2_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode); >> + sc->N2_bits = sc->N2_bytes * 8; >> + /* Assume that we are going to receive the count */ >> + sc->N2_rx = sc->N2_bytes; >> + sc->N2_tx = 0; >> + /* Let Forced Implicit mode have an effect on the counts */ >> + if (GETFIELD(PPC_BIT(53), sc->counter_config_reg) == 1) { >> + /* >> + * If Forced Implicit mode and count control doesn't >> + * indicate a receive then reset the rx count to 0 >> + */ >> + if (GETFIELD(PPC_BIT(55), sc->counter_config_reg) == 0) { >> + sc->N2_rx = 0; >> + } >> + /* If tx count control for N2 is set, load the tx value */ >> + if (GETFIELD(PPC_BIT(54), sc->counter_config_reg) == 1) { >> + sc->N2_tx = sc->N2_bytes; >> + } >> + } >> + } >> + /* >> + * Enforce an upper limit on the size of N1 that is equal to the >> + * known size of the shift register, 64 bits or 72 bits if ECC >> + * is enabled. >> + * If the size exceeds 72 bits it is a user error so log an error, >> + * cap the size at a max of 64 bits or 72 bits and set the >> sequencer FSM >> + * error bit. >> + */ >> + uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30), >> + sc->clock_config_reset_control); >> + if (ecc_control == 0 || ecc_control == 2) { >> + if (sc->N2_bytes > (SPI_CONTROLLER_REG_SIZE + 1)) { >> + SPI_DEBUG(qemu_log("Unsupported N2 shift size when ECC >> enabled, " >> + "bytes = 0x%x, bits = 0x%x\n", >> + sc->N2_bytes, sc->N2_bits)); >> + sc->N2_bytes = SPI_CONTROLLER_REG_SIZE + 1; >> + sc->N2_bits = sc->N2_bytes * 8; >> + } >> + } else if (sc->N2_bytes > SPI_CONTROLLER_REG_SIZE) { >> + SPI_DEBUG(qemu_log("Unsupported N2 shift size, bytes = 0x%x, " >> + "bits = 0x%x\n", sc->N2_bytes, >> sc->N2_bits)); >> + sc->N2_bytes = SPI_CONTROLLER_REG_SIZE; >> + sc->N2_bits = sc->N2_bytes * 8; >> + } >> +} /* end of calculate_N2 */ >> + >> +/* >> + * Shift_N2 operation handler method >> + */ >> + >> +bool operation_shiftn2(PnvSpiController *sc, uint8_t opcode, >> + xfer_buffer **payload) >> +{ >> + uint8_t n2_count; >> + bool stop = false; >> + >> + /* >> + * If there isn't a current payload left over from a stopped >> sequence >> + * create a new one. >> + */ >> + if (*payload == NULL) { >> + SPI_DEBUG(qemu_log("Creating new payload xfer_buffer\n")); >> + *payload = xfer_buffer_new(); >> + } >> + /* >> + * Use a combination of N2 counters to build the N2 portion of the >> + * transmit payload. >> + */ >> + calculate_N2(sc, opcode); >> + SPI_DEBUG(qemu_log("Shift N2 started\n")); >> + log_all_N_counts(sc); >> + /* >> + * The only difference between this code and the code for shift >> N1 is >> + * that this code has to account for the possible presence of N1 >> transmit >> + * bytes already taken from the TDR. >> + * If there are bytes to be transmitted for the N2 portion of >> the frame >> + * and there are still bytes in TDR that have not been copied >> into the >> + * TX data of the payload, this code will handle transmitting those >> + * remaining bytes. >> + * If for some reason the transmit count(s) add up to more than >> the size >> + * of the TDR we will just append 0xFF to the transmit payload >> data until >> + * the payload is N1 + N2 bytes long. >> + */ >> + n2_count = 0; >> + while (n2_count < sc->N2_bytes) { >> + /* >> + * If the RDR is full and we need to RX just bail out, >> letting the >> + * code continue will end up building the payload twice in >> the same >> + * buffer since RDR full causes a sequence stop and restart. >> + */ >> + if ((sc->N2_rx != 0) && >> + (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1)) { >> + SPI_DEBUG(qemu_log("Shift N2 set for receive but RDR is >> full, " >> + "requesting sequencer stop\n")); >> + stop = true; >> + break; >> + } >> + if ((sc->N2_tx != 0) && ((sc->N1_tx + n2_count) < >> + SPI_CONTROLLER_REG_SIZE)) { >> + /* Always append data for the N2 segment if it is set >> for TX */ >> + uint8_t n2_byte = 0x00; >> + n2_byte = get_from_offset(sc, (sc->N1_tx + n2_count)); >> + SPI_DEBUG(qemu_log("Extracting tx n2_byte = 0x%2.2x at >> index %d " >> + "from TDR\n", n2_byte, (sc->N1_tx + n2_count))); >> + if (sc->reverse_bits) { >> + SPI_DEBUG(qemu_log("Reversing bit order of tx >> n2_byte\n")); >> + n2_byte = reverse_bits8(n2_byte); >> + } >> + SPI_DEBUG(qemu_log("Appending tx n2_byte = 0x%2.2x to >> Payload\n", >> + n2_byte)); >> + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = >> n2_byte; >> + } else { >> + /* >> + * Regardless of whether or not N2 is set for TX or RX, >> we need >> + * the number of bytes in the payload to match the >> overall length >> + * of the operation. >> + */ >> + SPI_DEBUG(qemu_log("Appending tx n2_byte = 0xFF to >> Payload\n")); >> + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = >> 0xff; >> + } >> + n2_count++; >> + } /* end of while */ >> + if (!stop) { >> + uint32_t tx; >> + uint32_t rx; >> + uint8_t *read_buf = NULL; >> + xfer_buffer *rsp_payload = NULL; >> + >> + /* We have a TX and a full TDR or an RX and an empty RDR */ >> + SPI_DEBUG(qemu_log("Shifting N2 frame: first = %d, last = %d, " >> + "n1+n2 bits = %d\n", sc->first, sc->last, >> + (sc->N1_bits + sc->N2_bits))); >> + rsp_payload = xfer_buffer_new(); >> + for (int offset = 0; offset < (*payload)->len; offset = >> offset + 4) { >> + xfer_buffer_read_ptr(*payload, &read_buf, offset, 4); >> + tx = 0; >> + for (int i = 0; i < 4; i++) { >> + if ((offset + i) >= (*payload)->len) { >> + break; >> + } >> + tx = (tx << 8) | read_buf[i]; >> + } >> + rx = ssi_transfer((sc->bus).ssi_bus, tx); >> + for (int i = 0; i < 4; i++) { >> + if ((offset + i) >= (*payload)->len) { >> + break; >> + } >> + *(xfer_buffer_write_ptr(rsp_payload, >> rsp_payload->len, 1)) = >> + (rx >> (24 - i * 8)) & 0xFF; >> + } >> + } >> + if (rsp_payload != NULL) { >> + spi_response(sc, (sc->N1_bits + sc->N2_bits), rsp_payload); >> + } >> + sc->first = 0; >> + sc->last = 0; >> + /* >> + * If we are doing an N2 TX and the TDR is full we need to >> clear the >> + * TDR_full status. Do this here instead of up in the loop >> above so we >> + * don't log the message in every loop iteration. >> + */ >> + if ((sc->N2_tx != 0) && >> + (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1)) { >> + sc->status_reg = SETFIELD(STATUS_REG_TDR_FULL, >> sc->status_reg, 0); >> + SPI_DEBUG(qemu_log("TDR_full set to 0\n")); >> + } >> + /* >> + * The N2 frame shift is complete so reset the N2 counters. >> + * Reset the N1 counters also in case the frame was a >> combination of >> + * N1 and N2 segments. >> + */ >> + sc->N2_bits = 0; >> + sc->N2_bytes = 0; >> + sc->N2_tx = 0; >> + sc->N2_rx = 0; >> + sc->N1_bits = 0; >> + sc->N1_bytes = 0; >> + sc->N1_tx = 0; >> + sc->N1_rx = 0; >> + xfer_buffer_free(*payload); >> + *payload = NULL; >> + SPI_DEBUG(qemu_log("Payload buffer freed\n")); >> + } else { >> + SPI_DEBUG(qemu_log("Not shifting N2, stop = %d\n", stop)); >> + } >> + return stop; >> +} /* end of operation_shiftn2()*/ >> + >> +/* >> + * The SPIC engine and its internal sequencer can be interrupted and >> reset by >> + * a hardware signal, the sbe_spicst_hard_reset bits from Pervasive >> + * Miscellaneous Register of sbe_register_bo device. >> + * Reset immediately aborts any SPI transaction in progress and >> returns the >> + * sequencer and state machines to idle state. >> + * The configuration register values are not changed. The status >> register is >> + * not reset. The engine registers are not reset. >> + * The SPIC engine reset does not have any affect on the attached >> devices. >> + * Reset handling of any attached devices is beyond the scope of the >> engine. >> + */ >> +static void do_reset(DeviceState *dev) >> +{ >> + PnvSpiController *sc = PNV_SPICONTROLLER(dev); >> + SPI_DEBUG(qemu_log("Resetting spic engine sequencer >> configuration and spi " >> + "communication\n")); >> + /* Reset all N1 and N2 counters, and other constants */ >> + sc->first = 0; >> + sc->last = 0; >> + sc->N2_bits = 0; >> + sc->N2_bytes = 0; >> + sc->N2_tx = 0; >> + sc->N2_rx = 0; >> + sc->N1_bits = 0; >> + sc->N1_bytes = 0; >> + sc->N1_tx = 0; >> + sc->N1_rx = 0; >> + sc->loop_counter_1 = 0; >> + sc->loop_counter_2 = 0; >> + SPI_DEBUG(qemu_log("Disconnected from responder\n")); >> + qemu_set_irq((sc->bus).cs_line[0], 1); >> +} >> + >> static void pnv_spi_bus_realize(DeviceState *dev, Error **errp) >> { >> PnvSPIBus *s = PNV_SPI_BUS(dev); >> @@ -191,6 +1498,7 @@ static const TypeInfo pnv_spi_bus_info = { >> static Property pnv_spi_controller_properties[] = { >> DEFINE_PROP_UINT32("spic_num", PnvSpiController, spic_num, 0), >> + DEFINE_PROP_BOOL("reverse_bits", PnvSpiController, reverse_bits, >> false), >> DEFINE_PROP_END_OF_LIST(), >> }; >> @@ -254,6 +1562,7 @@ static void >> pnv_spi_controller_class_init(ObjectClass *klass, void *data) >> dc->desc = "PowerNV SPI Controller"; >> dc->realize = pnv_spi_controller_realize; >> + dc->reset = do_reset; >> device_class_set_props(dc, pnv_spi_controller_properties); >> } >
diff --git a/include/hw/ppc/pnv_spi_controller.h b/include/hw/ppc/pnv_spi_controller.h index 5ec50fb14c..ee8e7a17da 100644 --- a/include/hw/ppc/pnv_spi_controller.h +++ b/include/hw/ppc/pnv_spi_controller.h @@ -8,6 +8,14 @@ * This model Supports a connection to a single SPI responder. * Introduced for P10 to provide access to SPI seeproms, TPM, flash device * and an ADC controller. + * + * All SPI function control is mapped into the SPI register space to enable + * full control by firmware. + * + * SPI Controller has sequencer and shift engine. The SPI shift engine + * performs serialization and de-serialization according to the control by + * the sequencer and according to the setup defined in the configuration + * registers and the SPI sequencer implements the main control logic. */ #include "hw/ssi/ssi.h" @@ -21,6 +29,7 @@ #define SPI_CONTROLLER_REG_SIZE 8 typedef struct SSIBus SSIBus; +typedef struct xfer_buffer xfer_buffer; #define TYPE_PNV_SPI_BUS "pnv-spi-bus" OBJECT_DECLARE_SIMPLE_TYPE(PnvSPIBus, PNV_SPI_BUS) @@ -33,6 +42,21 @@ typedef struct PnvSPIBus { uint32_t id; } PnvSPIBus; +/* xfer_buffer */ +typedef struct xfer_buffer { + + uint32_t len; + uint8_t *data; + +} xfer_buffer; + +uint8_t *xfer_buffer_write_ptr(xfer_buffer *payload, uint32_t offset, + uint32_t length); +void xfer_buffer_read_ptr(xfer_buffer *payload, uint8_t **read_buf, + uint32_t offset, uint32_t length); +xfer_buffer *xfer_buffer_new(void); +void xfer_buffer_free(xfer_buffer *payload); + typedef struct PnvSpiController { DeviceState parent; @@ -40,6 +64,39 @@ typedef struct PnvSpiController { MemoryRegion xscom_spic_regs; /* SPI controller object number */ uint32_t spic_num; + uint8_t responder_select; + /* To verify if shift_n1 happens prior to shift_n2 */ + bool shift_n1_done; + /* + * Internal flags for the first and last indicators for the SPI + * interface methods + */ + uint8_t first; + uint8_t last; + /* Loop counter for branch operation opcode Ex/Fx */ + uint8_t loop_counter_1; + uint8_t loop_counter_2; + /* N1/N2_bits specifies the size of the N1/N2 segment of a frame in bits.*/ + uint8_t N1_bits; + uint8_t N2_bits; + /* Number of bytes in a payload for the N1/N2 frame segment.*/ + uint8_t N1_bytes; + uint8_t N2_bytes; + /* Number of N1/N2 bytes marked for transmit */ + uint8_t N1_tx; + uint8_t N2_tx; + /* Number of N1/N2 bytes marked for receive */ + uint8_t N1_rx; + uint8_t N2_rx; + /* + * Setting this attribute to true will cause the engine to reverse the + * bit order of each byte it appends to a payload before sending the + * payload to a device. There may be cases where an end device expects + * a reversed order, like in the case of the Nuvoton TPM device. The + * order of bytes in the payload is not reversed, only the order of the + * 8 bits in each payload byte. + */ + bool reverse_bits; /* SPI Controller registers */ uint64_t error_reg; @@ -52,4 +109,19 @@ typedef struct PnvSpiController { uint8_t sequencer_operation_reg[SPI_CONTROLLER_REG_SIZE]; uint64_t status_reg; } PnvSpiController; + +void log_all_N_counts(PnvSpiController *spi_controller); +void spi_response(PnvSpiController *spi_controller, int bits, + xfer_buffer *rsp_payload); +void operation_sequencer(PnvSpiController *spi_controller); +bool operation_shiftn1(PnvSpiController *spi_controller, uint8_t opcode, + xfer_buffer **payload, bool send_n1_alone); +bool operation_shiftn2(PnvSpiController *spi_controller, uint8_t opcode, + xfer_buffer **payload); +bool does_rdr_match(PnvSpiController *spi_controller); +uint8_t get_from_offset(PnvSpiController *spi_controller, uint8_t offset); +void shift_byte_in(PnvSpiController *spi_controller, uint8_t byte); +void calculate_N1(PnvSpiController *spi_controller, uint8_t opcode); +void calculate_N2(PnvSpiController *spi_controller, uint8_t opcode); +uint8_t reverse_bits8(uint8_t x); #endif /* PPC_PNV_SPI_CONTROLLER_H */ diff --git a/hw/ppc/pnv_spi_controller.c b/hw/ppc/pnv_spi_controller.c index e2478a47f2..afe7f17565 100644 --- a/hw/ppc/pnv_spi_controller.c +++ b/hw/ppc/pnv_spi_controller.c @@ -52,6 +52,11 @@ static uint64_t pnv_spi_controller_read(void *opaque, hwaddr addr, val)); sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, sc->status_reg, 0); SPI_DEBUG(qemu_log("RDR being read, RDR_full set to 0\n")); + if (GETFIELD(STATUS_REG_SHIFTER_FSM, sc->status_reg) == FSM_WAIT) { + SPI_DEBUG(qemu_log("RDR being read while shifter is waiting, " + "starting sequencer\n")); + operation_sequencer(sc); + } break; case SEQUENCER_OPERATION_REG: val = 0; @@ -124,13 +129,15 @@ static void pnv_spi_controller_write(void *opaque, hwaddr addr, sc->status_reg = SETFIELD(STATUS_REG_TDR_UNDERRUN, sc->status_reg, 0); SPI_DEBUG(qemu_log("TDR being written, TDR_underrun set to 0\n")); SPI_DEBUG(qemu_log("TDR being written, starting sequencer\n")); + operation_sequencer(sc); + break; case RECEIVE_DATA_REG: sc->receive_data_reg = val; break; case SEQUENCER_OPERATION_REG: for (int i = 0; i < SPI_CONTROLLER_REG_SIZE; i++) { - sc->sequencer_operation_reg[i] = (val >> (56 - i * 8)) & 0xFF; + sc->sequencer_operation_reg[i] = (val >> (56 - i * 8)) & 0xFF; } break; case STATUS_REG: @@ -157,6 +164,1306 @@ static const MemoryRegionOps pnv_spi_controller_xscom_ops = { .endianness = DEVICE_BIG_ENDIAN, }; +/* xfer_buffer_methods */ +xfer_buffer *xfer_buffer_new(void) +{ + xfer_buffer *payload = g_malloc0(sizeof(*payload)); + + payload->data = g_malloc0(payload->len); + return payload; +} + +void xfer_buffer_free(xfer_buffer *payload) +{ + free(payload->data); + free(payload); +} + +uint8_t *xfer_buffer_write_ptr(xfer_buffer *payload, uint32_t offset, + uint32_t length) +{ + if (payload->len < (offset + length)) { + payload->len = offset + length; + payload->data = g_realloc(payload->data, payload->len); + } + return &payload->data[offset]; +} + +void xfer_buffer_read_ptr(xfer_buffer *payload, uint8_t **read_buf, + uint32_t offset, uint32_t length) +{ + static uint32_t prev_len; + if ((prev_len != length) || (*read_buf == NULL)) { + *read_buf = g_realloc(*read_buf, length); + prev_len = length; + } + if (offset > payload->len) { + /* Reading outside payload, just return */ + return; + } + *read_buf = &payload->data[offset]; +} + +uint8_t reverse_bits8(uint8_t x) +{ + x = (x << 4) | (x >> 4); + x = ((x & 0x33) << 2) | ((x & 0xcc) >> 2); + x = ((x & 0x55) << 1) | ((x & 0xaa) >> 1); + return x; +} + +bool does_rdr_match(PnvSpiController *sc) +{ + /* + * According to spec, the mask bits that are 0 are compared and the + * bits that are 1 are ignored. + */ + uint16_t rdr_match_mask = GETFIELD(MEMORY_MAPPING_REG_RDR_MATCH_MASK, + sc->memory_mapping_reg); + uint16_t rdr_match_val = GETFIELD(MEMORY_MAPPING_REG_RDR_MATCH_VAL, + sc->memory_mapping_reg); + if ((~rdr_match_mask & rdr_match_val) == ((~rdr_match_mask) & + GETFIELD(PPC_BITMASK(48, 63), sc->receive_data_reg))) { + SPI_DEBUG(qemu_log("RDR match successful, match=0x%4.4x, " + "mask=0x%4.4x, RDR[48:63]=0x%4.4llx\n", + rdr_match_val, rdr_match_mask, + GETFIELD(PPC_BITMASK(48, 63), + sc->receive_data_reg))); + return true; + } else { + SPI_DEBUG(qemu_log("RDR match failed, match=0x%4.4x, mask=0x%4.4x, " + "RDR[48:63]=0x%4.4llx\n", rdr_match_val, rdr_match_mask, + GETFIELD(PPC_BITMASK(48, 63), sc->receive_data_reg))); + return false; + } +} + +uint8_t get_from_offset(PnvSpiController *sc, uint8_t offset) +{ + uint8_t byte; + + /* + * Offset is an index between 0 and SPI_CONTROLLER_REG_SIZE - 1 + * Check the offset before using it. + */ + if (offset < SPI_CONTROLLER_REG_SIZE) { + byte = (sc->transmit_data_reg >> (56 - offset * 8)) & 0xFF; + } else { + /* + * Log an error and return a 0xFF since we have to assign something + * to byte before returning. + */ + qemu_log_mask(LOG_GUEST_ERROR, "Invalid offset = %d used to get byte " + "from TDR\n", offset); + byte = 0xff; + } + return byte; +} + +void shift_byte_in(PnvSpiController *sc, uint8_t byte) +{ + sc->receive_data_reg = (sc->receive_data_reg << 8) | byte; + SPI_DEBUG(qemu_log("0x%2.2x shifted in, RDR now = 0x%16.16lx\n", byte, + sc->receive_data_reg)); +} + +void spi_response(PnvSpiController *sc, int bits, xfer_buffer *rsp_payload) +{ + uint8_t *read_buf = NULL; + uint8_t ecc_count; + uint8_t shift_in_count; + + /* + * Processing here must handle: + * - Which bytes in the payload we should move to the RDR + * - Explicit mode counter configuration settings + * - RDR full and RDR overrun status + */ + + /* + * First check that the response payload is the exact same + * number of bytes as the request payload was + */ + if (rsp_payload->len != (sc->N1_bytes + sc->N2_bytes)) { + qemu_log_mask(LOG_GUEST_ERROR, "Invalid response payload size in " + "bytes, expected %d, got %d\n", + (sc->N1_bytes + sc->N2_bytes), rsp_payload->len); + } else { + uint8_t ecc_control; + SPI_DEBUG(qemu_log("SPI response received, payload len = %d\n", + rsp_payload->len)); + log_all_N_counts(sc); + /* + * Adding an ECC count let's us know when we have found a payload byte + * that was shifted in but cannot be loaded into RDR. Bits 29-30 + * equal to either 0b00 or 0b10 indicate that we are taking in data + * with ECC and either applying the ECC or discarding it. + */ + ecc_count = 0; + ecc_control = GETFIELD(PPC_BITMASK(29, 30), + sc->clock_config_reset_control); + if (ecc_control == 0 || ecc_control == 2) { + ecc_count = 1; + } + /* + * Use the N1_rx and N2_rx counts to control shifting data from the + * payload into the RDR. Keep an overall count of the number of bytes + * shifted into RDR so we can discard every 9th byte when ECC is + * enabled. + */ + shift_in_count = 0; + /* Handle the N1 portion of the frame first */ + if (sc->N1_rx != 0) { + uint8_t n1_count = 0; + while (n1_count < sc->N1_bytes) { + shift_in_count++; + xfer_buffer_read_ptr(rsp_payload, &read_buf, n1_count, 1); + if ((ecc_count != 0) && + (shift_in_count == (SPI_CONTROLLER_REG_SIZE + ecc_count))) { + SPI_DEBUG(qemu_log("Discarding rx N1 ECC byte = 0x%2.2x at " + "payload index = %d\n", read_buf[0], n1_count)); + shift_in_count = 0; + } else { + uint8_t n1_byte = 0x00; + n1_byte = read_buf[0]; + SPI_DEBUG(qemu_log("Extracting rx n1_byte = 0x%2.2x from " + "payload at index = %d\n", n1_byte, n1_count)); + if (sc->reverse_bits) { + SPI_DEBUG(qemu_log("Reversing bit order of rx " + "n1_byte\n")); + n1_byte = reverse_bits8(n1_byte); + } + SPI_DEBUG(qemu_log("Shifting rx N1 byte = 0x%2.2x into " + "RDR\n", n1_byte)); + shift_byte_in(sc, n1_byte); + } + n1_count++; + } /* end of while */ + } + /* Handle the N2 portion of the frame */ + if (sc->N2_rx != 0) { + uint8_t n2_count = 0; + while (n2_count < sc->N2_bytes) { + shift_in_count++; + xfer_buffer_read_ptr(rsp_payload, &read_buf, + (sc->N1_bytes + n2_count), 1); + if ((ecc_count != 0) && + (shift_in_count == (SPI_CONTROLLER_REG_SIZE + ecc_count))) { + SPI_DEBUG(qemu_log("Discarding rx N1 ECC byte = 0x%2.2x at " + "payload index = %d\n", read_buf[0], + (sc->N1_bytes + n2_count))); + shift_in_count = 0; + } else { + /* + * The code handles shifting data from the payload received + * from the responder into the responder's RDR. Since this + * is an N2 frame segment it is safe to assume that there + * was a preceding N1 segment which was combined with an N2 + * segment to create a single frame. The response data will + * then have N1_bytes of data in the payload representing a + * responder response to the N1 section of the frame. If N2 + * is set to receive the shifting for N2 data begins after + * the N1 bytes regardless of whether or not N1 was marked + * for transmit or receive. + */ + uint8_t n2_byte = 0x00; + n2_byte = read_buf[0]; + SPI_DEBUG(qemu_log("Extracting rx n2_byte = 0x%2.2x from " + "payload at index = %d\n", n2_byte, + (sc->N1_bytes + n2_count))); + if (sc->reverse_bits) { + SPI_DEBUG(qemu_log("Reversing bit order of rx " + "n2_byte\n")); + n2_byte = reverse_bits8(n2_byte); + } + SPI_DEBUG(qemu_log("Shifting rx N2 byte = 0x%2.2x into " + "RDR\n", n2_byte)); + shift_byte_in(sc, n2_byte); + } + n2_count++; + } + } + if ((sc->N1_rx + sc->N2_rx) > 0) { + /* + * Data was received so handle RDR status. + * It is easier to handle RDR_full and RDR_overrun status here + * since the RDR register's shift_byte_in method is called + * multiple times in a row. Controlling RDR status is done here + * instead of in the RDR scoped methods for that reason. + */ + if (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1) { + /* + * Data was shifted into the RDR before having been read + * causing previous data to have been overrun. + */ + sc->status_reg = SETFIELD(STATUS_REG_RDR_OVERRUN, + sc->status_reg, 1); + } else { + /* + * Set status to indicate that the received data register is + * full. This flag is only cleared once the RDR is unloaded. + */ + sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, + sc->status_reg, 1); + SPI_DEBUG(qemu_log("RDR_full set to 1\n")); + } + } + } /* end of else */ +} /* end of spi_response() */ + +void log_all_N_counts(PnvSpiController *sc) +{ + SPI_DEBUG(qemu_log("N1_bits = %d, N1_bytes = %d, N1_tx = %d, N1_rx = %d, " + "N2_bits = %d, N2_bytes = %d, N2_tx = %d, N2_rx = %d\n", + sc->N1_bits, sc->N1_bytes, sc->N1_tx, sc->N1_rx, sc->N2_bits, + sc->N2_bytes, sc->N2_tx, sc->N2_rx)); +} + +static inline void next_sequencer_fsm(PnvSpiController *sc) +{ + uint8_t seq_index = GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg); + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg, + (seq_index + 1)); + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg, + SEQ_STATE_INDEX_INCREMENT); +} + +void operation_sequencer(PnvSpiController *sc) +{ + /* + * Loop through each sequencer operation ID and perform the requested + * operations. + * Flag for indicating if we should send the N1 frame or wait to combine + * it with a preceding N2 frame. + */ + bool send_n1_alone = true; + bool stop = false; /* Flag to stop the sequencer */ + uint8_t opcode = 0; + uint8_t masked_opcode = 0; + + /* + * xfer_buffer for containing the payload of the SPI frame. + * This is a static because there are cases where a sequence has to stop + * and wait for the target application to unload the RDR. If this occurs + * during a sequence where N1 is not sent alone and instead combined with + * N2 since the N1 tx length + the N2 tx length is less than the size of + * the TDR. + */ + static xfer_buffer *payload; + + if (payload == NULL) { + payload = xfer_buffer_new(); + } + /* + * Clear the sequencer FSM error bit - general_SPI_status[3] + * before starting a sequence. + */ + sc->status_reg = SETFIELD(PPC_BIT(35), sc->status_reg, 0); + /* + * If the FSM is idle set the sequencer index to 0 + * (new/restarted sequence) + */ + if (GETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg) == + SEQ_STATE_IDLE) { + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg, 0); + } + /* + * There are only 8 possible operation IDs to iterate through though + * some operations may cause more than one frame to be sequenced. + */ + while (GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg) < 8) { + opcode = sc->sequencer_operation_reg[GETFIELD( + STATUS_REG_SEQUENCER_INDEX, sc->status_reg)]; + /* Set sequencer state to decode */ + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, sc->status_reg, + SEQ_STATE_DECODE); + /* + * Only the upper nibble of the operation ID is needed to know what + * kind of operation is requested. + */ + masked_opcode = opcode & 0xF0; + switch (masked_opcode) { + /* + * Increment the operation index in each case instead of just + * once at the end in case an operation like the branch + * operation needs to change the index. + */ + case SEQ_OP_STOP: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + /* A stop operation in any position stops the sequencer */ + SPI_DEBUG(qemu_log("Sequencer STOP at index = 0x%llx, sequencer " + "idling\n", GETFIELD( + STATUS_REG_SEQUENCER_INDEX, + sc->status_reg))); + stop = true; + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, sc->status_reg, + FSM_IDLE); + sc->loop_counter_1 = 0; + sc->loop_counter_2 = 0; + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_IDLE); + break; + + case SEQ_OP_SELECT_SLAVE: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + SPI_DEBUG(qemu_log("Sequencer SELECT_SLAVE at index = 0x%llx\n", + GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); + /* + * This device currently only supports a single responder + * connection at position 0. De-selecting a responder is fine + * and expected at the end of a sequence but selecting any + * responder other than 0 should cause an error. + */ + sc->responder_select = opcode & 0x0F; + if (sc->responder_select == 0) { + SPI_DEBUG(qemu_log("Shifter done, pull the CS line high\n")); + qemu_set_irq((sc->bus).cs_line[0], 1); + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg, + (GETFIELD( + STATUS_REG_SEQUENCER_INDEX, + sc->status_reg) + 1)); + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_DONE); + } else if (sc->responder_select != 1) { + qemu_log_mask(LOG_GUEST_ERROR, "Slave selection other than 1 " + "not supported, select = 0x%x\n", + sc->responder_select); + SPI_DEBUG(qemu_log("Sequencer stop requested due to invalid " + "responder select at index = 0x%llx, " + "shifter idling\n", GETFIELD( + STATUS_REG_SEQUENCER_INDEX, + sc->status_reg))); + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_IDLE); + stop = true; + } else { + /* + * Only allow an FSM_START state when a responder is + * selected + */ + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_START); + SPI_DEBUG(qemu_log("shifter starting, pull CS line low\n")); + qemu_set_irq((sc->bus).cs_line[0], 0); + sc->first = 1; + sc->last = 0; + /* + * A Shift_N2 operation is only valid after a Shift_N1 + * according to the spec. The spec doesn't say if that means + * immediately after or just after at any point. We will track + * the occurrence of a Shift_N1 to enforce this requirement in + * the most generic way possible by assuming that the rule + * applies once a valid responder select has occurred. + */ + sc->shift_n1_done = false; + next_sequencer_fsm(sc); + } + break; + + case SEQ_OP_SHIFT_N1: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + SPI_DEBUG(qemu_log("Sequencer SHIFT_N1 at index = 0x%llx\n", + GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); + /* + * Only allow a shift_n1 when the state is not IDLE or DONE. + * In either of those two cases the sequencer is not in a proper + * state to perform shift operations because the sequencer has: + * - processed a responder deselect (DONE) + * - processed a stop opcode (IDLE) + * - encountered an error (IDLE) + */ + if ((GETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg) == FSM_IDLE) || + (GETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg) == FSM_DONE)) { + qemu_log_mask(LOG_GUEST_ERROR, "Shift_N1 not allowed in " + "shifter state = 0x%llx", GETFIELD( + STATUS_REG_SHIFTER_FSM, sc->status_reg)); + /* + * Set sequencer FSM error bit 3 (general_SPI_status[3]) + * in status reg. + */ + sc->status_reg = SETFIELD(PPC_BIT(35), sc->status_reg, 1); + SPI_DEBUG(qemu_log("Sequencer stop requested due to invalid " + "shifter state at index = 0x%llx\n", GETFIELD( + STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); + stop = true; + } else { + /* + * Look for the special case where there is a shift_n1 set for + * transmit and it is followed by a shift_n2 set for transmit + * AND the combined transmit length of the two operations is + * less than or equal to the size of the TDR register. In this + * case we want to use both this current shift_n1 opcode and the + * following shift_n2 opcode to assemble the frame for + * transmission to the responder without requiring a refill of + * the TDR between the two operations. + */ + if ((sc->sequencer_operation_reg[GETFIELD( + STATUS_REG_SEQUENCER_INDEX, sc->status_reg) + 1] & 0xF0) + == SEQ_OP_SHIFT_N2) { + SPI_DEBUG(qemu_log("Not sending N1 alone\n")); + send_n1_alone = false; + } + /* + * If the next opcode is 0x10, which deselects the SPI device + * then this is the last shift + */ + if (sc->sequencer_operation_reg[GETFIELD( + STATUS_REG_SEQUENCER_INDEX, sc->status_reg) + 1] == + SEQ_OP_SELECT_SLAVE) { + sc->last = 1; + } + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_SHIFT_N1); + stop = operation_shiftn1(sc, opcode, &payload, send_n1_alone); + if (stop) { + /* + * The operation code says to stop, this can occur if: + * (1) RDR is full and the N1 shift is set for receive + * (2) TDR was empty at the time of the N1 shift so we need + * to wait for data. + * (3) Neither 1 nor 2 are occurring and we aren't sending + * N1 alone and N2 counter reload is set (bit 0 of the N2 + * counter reload field). In this case TDR_underrun will + * will be set and the Payload has been loaded so it is + * ok to advance the sequencer. + */ + if (GETFIELD(STATUS_REG_TDR_UNDERRUN, sc->status_reg)) { + SPI_DEBUG(qemu_log("Sequencer stop requested due to N2 " + "counter reload active.\n")); + sc->shift_n1_done = true; + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, + FSM_SHIFT_N2); + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg, + (GETFIELD( + STATUS_REG_SEQUENCER_INDEX, + sc->status_reg) + 1)); + SPI_DEBUG(qemu_log("Set new sequencer index to = " + "0x%llx\n", GETFIELD( + STATUS_REG_SEQUENCER_INDEX, + sc->status_reg))); + } else { + /* + * This is case (1) or (2) so the sequencer needs to + * wait and NOT go to the next sequence yet. + */ + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_WAIT); + } + } else { + /* Ok to move on to the next index */ + sc->shift_n1_done = true; + next_sequencer_fsm(sc); + } + } + break; + + case SEQ_OP_SHIFT_N2: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + SPI_DEBUG(qemu_log("Sequencer SHIFT_N2 at index = %lld\n", + GETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg))); + if (!sc->shift_n1_done) { + qemu_log_mask(LOG_GUEST_ERROR, "Shift_N2 is not allowed if a " + "Shift_N1 is not done, shifter state = 0x%llx", + GETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg)); + /* + * In case the sequencer actually stops if an N2 shift is + * requested before any N1 shift is done. Set sequencer FSM + * error bit 3 (general_SPI_status[3]) in status reg. + */ + sc->status_reg = SETFIELD(PPC_BIT(35), sc->status_reg, 1); + SPI_DEBUG(qemu_log("Sequencer stop requested due to shift_n2 " + "w/no shift_n1 done at index = 0x%llx\n", + GETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg))); + stop = true; + } else { + /* + * If the next opcode is 0x10, which deselects the SPI device + * then this is the last shift + */ + if (sc->sequencer_operation_reg[GETFIELD( + STATUS_REG_SEQUENCER_INDEX, + sc->status_reg) + 1] == SEQ_OP_SELECT_SLAVE) { + sc->last = 1; + } + /* Ok to do a Shift_N2 */ + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_SHIFT_N2); + stop = operation_shiftn2(sc, opcode, &payload); + /* + * If the operation code says to stop set the shifter state to + * wait and stop + */ + if (stop) { + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_WAIT); + } else { + /* Ok to move on to the next index */ + next_sequencer_fsm(sc); + } + } + break; + + case SEQ_OP_BRANCH_IFNEQ_RDR: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_RDR at " + "index = 0x%llx\n", GETFIELD( + STATUS_REG_SEQUENCER_INDEX, sc->status_reg))); + /* + * The memory mapping register RDR match value is compared against + * the 16 rightmost bytes of the RDR (potentially with masking). + * Since this comparison is performed against the contents of the + * RDR then a receive must have previously occurred otherwise + * there is no data to compare and the operation cannot be + * completed and will stop the sequencer until RDR full is set to + * 1. + */ + if (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1) { + bool rdr_matched = false; + rdr_matched = does_rdr_match(sc); + if (rdr_matched) { + SPI_DEBUG(qemu_log("Proceed to next sequencer index " + "(increment on RDR match)\n")); + /* A match occurred, increment the sequencer index. */ + next_sequencer_fsm(sc); + } else { + SPI_DEBUG(qemu_log("Proceed to sequencer index=0x%x " + "(branch on RDR match fail)\n", (opcode & 0x7))); + /* + * Branch the sequencer to the index coded into the op + * code. + */ + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg, (opcode & 0x7)); + } + /* + * Regardless of where the branch ended up we want the + * sequencer to continue shifting so we have to clear + * RDR_full. + */ + sc->status_reg = SETFIELD(STATUS_REG_RDR_FULL, + sc->status_reg, 0); + } else { + SPI_DEBUG(qemu_log("RDR not full for 0x6x opcode! Stopping " + "sequencer.\n")); + stop = true; + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, + sc->status_reg, FSM_WAIT); + } + break; + + case SEQ_OP_TRANSFER_TDR: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + qemu_log_mask(LOG_GUEST_ERROR, "Transfer TDR is not supported\n"); + next_sequencer_fsm(sc); + break; + + case SEQ_OP_BRANCH_IFNEQ_INC_1: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_INC_1 at index = " + "0x%llx, next index = %d, count_compare_1 = " + "0x%llx, loop_counter_1 = %d\n", GETFIELD( + STATUS_REG_SEQUENCER_INDEX, sc->status_reg), + (opcode & 0x07), + GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, + sc->status_reg), sc->loop_counter_1)); + /* + * The spec says the loop should execute count compare + 1 times. + * However we learned from engineering that we really only loop + * count_compare times, count compare = 0 makes this op code a + * no-op + */ + if (sc->loop_counter_1 != + GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, + sc->counter_config_reg)) { + /* + * If the next opcode is 0x10, which deselects the SPI device + * and we know that the next opcode is the last one in the + * loop then the next shift is the last shift + */ + uint8_t condition1 = sc->sequencer_operation_reg[ + GETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg) + 1]; + uint8_t condition2 = GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE1, + sc->counter_config_reg); + + if ((condition1 == SEQ_OP_SELECT_SLAVE) && + ((sc->loop_counter_1 + 1) == condition2)) { + sc->last = 1; + } + /* + * Next index is the lower nibble of the branch operation ID, + * mask off all but the first three bits so we don't try to + * access beyond the sequencer_operation_reg boundary. + */ + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg, (opcode & 0x7)); + sc->loop_counter_1++; + SPI_DEBUG(qemu_log("Branching to index = %d, loop_counter_1 = " + "%d\n", (opcode & 0x7), sc->loop_counter_1)); + } else { + /* Continue to next index if loop counter is reached */ + next_sequencer_fsm(sc); + SPI_DEBUG(qemu_log("loop counter 1 achieved, next sequencer " + "index = 0x%llx\n", GETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg))); + } + break; + + case SEQ_OP_BRANCH_IFNEQ_INC_2: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + SPI_DEBUG(qemu_log("Sequencer BRANCH_IFNEQ_INC_2 at index = " + "0x%llx, next index = %d, count_compare_2 = " + "0x%llx, loop_counter_2 = %d\n", GETFIELD( + STATUS_REG_SEQUENCER_INDEX, sc->status_reg), + (opcode & 0x07), GETFIELD( + COUNTER_CONFIG_REG_COUNT_COMPARE2, + sc->status_reg), sc->loop_counter_2)); + /* + * If the next opcode is 0x10, which deselects the SPI device + * and we know that the next opcode is the last one in the + * loop then the next shift is the last shift + */ + uint8_t condition1 = sc->sequencer_operation_reg[ + GETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg) + 1]; + uint8_t condition2 = GETFIELD(COUNTER_CONFIG_REG_COUNT_COMPARE2, + sc->counter_config_reg); + + if ((condition1 == SEQ_OP_SELECT_SLAVE) && + ((sc->loop_counter_2 + 1) == condition2)) { + sc->last = 1; + } + /* + * The spec says the loop should execute count compare + 1 times. + * However we learned from engineering that we really only loop + * count_compare times, count compare = 0 makes this op code a + * no-op + */ + if (sc->loop_counter_2 != condition2) { + /* + * Next index is the lower nibble of the branch operation ID, + * mask off all but the first three bits so we don't try to + * access beyond the sequencer_operation_reg boundary. + */ + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg, + (opcode & 0x7)); + sc->loop_counter_2++; + SPI_DEBUG(qemu_log("Branching to index = %d, loop_counter_2 " + "= %d", (opcode & 0x7), + sc->loop_counter_2)); + } else { + /* Continue to next index if loop counter is reached */ + next_sequencer_fsm(sc); + SPI_DEBUG(qemu_log("loop counter 2 achieved, next sequencer " + "index = 0x%llx\n", GETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg))); + } + break; + + default: + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_EXECUTE); + qemu_log_mask(LOG_GUEST_ERROR, "Sequencer opcode 0x%x is not " + "supported\n", opcode); + /* Ignore unsupported operations. */ + next_sequencer_fsm(sc); + break; + } /* end of switch */ + /* + * If we used all 8 opcodes without seeing a 00 - STOP in the sequence + * we need to go ahead and end things as if there was a STOP at the + * end. + */ + if (GETFIELD(STATUS_REG_SEQUENCER_INDEX, sc->status_reg) == 8) { + SPI_DEBUG(qemu_log("All 8 opcodes completed, sequencer " + "idling\n")); + sc->status_reg = SETFIELD(STATUS_REG_SHIFTER_FSM, sc->status_reg, + FSM_IDLE); + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_INDEX, + sc->status_reg, 0); + sc->loop_counter_1 = 0; + sc->loop_counter_2 = 0; + sc->status_reg = SETFIELD(STATUS_REG_SEQUENCER_FSM, + sc->status_reg, SEQ_STATE_IDLE); + break; + } + /* Break the loop if a stop was requested */ + if (stop) { + break; + } + } /* end of while */ + return; +} /* end of operation_sequencer() */ + +/* + * Calculate the N1 counters based on passed in opcode and + * internal register values. + * The method assumes that the opcode is a Shift_N1 opcode + * and doesn't test it. + * The counters returned are: + * N1 bits: Number of bits in the payload data that are significant + * to the responder. + * N1_bytes: Total count of payload bytes for the N1 (portion of the) frame. + * N1_tx: Total number of bytes taken from TDR for N1 + * N1_rx: Total number of bytes taken from the payload for N1 + */ +void calculate_N1(PnvSpiController *sc, uint8_t opcode) +{ + /* + * Shift_N1 opcode form: 0x3M + * Implicit mode: + * If M != 0 the shift count is M bytes and M is the number of tx bytes. + * Forced Implicit mode: + * M is the shift count but tx and rx is determined by the count control + * register fields. Note that we only check for forced Implicit mode when + * M != 0 since the mode doesn't make sense when M = 0. + * Explicit mode: + * If M == 0 then shift count is number of bits defined in the + * Counter Configuration Register's shift_count_N1 field. + */ + if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) { + /* Explicit mode */ + sc->N1_bits = GETFIELD(COUNTER_CONFIG_REG_SHIFT_COUNT_N1, + sc->counter_config_reg); + sc->N1_bytes = ceil(sc->N1_bits / 8); + sc->N1_tx = 0; + sc->N1_rx = 0; + /* If tx count control for N1 is set, load the tx value */ + if (GETFIELD(PPC_BIT(50), sc->counter_config_reg) == 1) { + sc->N1_tx = sc->N1_bytes; + } + /* If rx count control for N1 is set, load the rx value */ + if (GETFIELD(PPC_BIT(51), sc->counter_config_reg) == 1) { + sc->N1_rx = sc->N1_bytes; + } + } else { + /* Implicit mode/Forced Implicit mode, use M field from opcode */ + sc->N1_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode); + sc->N1_bits = sc->N1_bytes * 8; + /* + * Assume that we are going to transmit the count + * (pure Implicit only) + */ + sc->N1_tx = sc->N1_bytes; + sc->N1_rx = 0; + /* Let Forced Implicit mode have an effect on the counts */ + if (GETFIELD(PPC_BIT(49), sc->counter_config_reg) == 1) { + /* + * If Forced Implicit mode and count control doesn't + * indicate transmit then reset the tx count to 0 + */ + if (GETFIELD(PPC_BIT(50), sc->counter_config_reg) == 0) { + sc->N1_tx = 0; + } + /* If rx count control for N1 is set, load the rx value */ + if (GETFIELD(PPC_BIT(51), sc->counter_config_reg) == 1) { + sc->N1_rx = sc->N1_bytes; + } + } + } + /* + * Enforce an upper limit on the size of N1 that is equal to the known size + * of the shift register, 64 bits or 72 bits if ECC is enabled. + * If the size exceeds 72 bits it is a user error so log an error, + * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM + * error bit. + */ + uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30), + sc->clock_config_reset_control); + if (ecc_control == 0 || ecc_control == 2) { + if (sc->N1_bytes > (SPI_CONTROLLER_REG_SIZE + 1)) { + qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size when " + "ECC enabled, bytes = 0x%x, bits = 0x%x\n", + sc->N1_bytes, sc->N1_bits); + sc->N1_bytes = SPI_CONTROLLER_REG_SIZE + 1; + sc->N1_bits = sc->N1_bytes * 8; + } + } else if (sc->N1_bytes > SPI_CONTROLLER_REG_SIZE) { + qemu_log_mask(LOG_GUEST_ERROR, "Unsupported N1 shift size, " + "bytes = 0x%x, bits = 0x%x\n", + sc->N1_bytes, sc->N1_bits); + sc->N1_bytes = SPI_CONTROLLER_REG_SIZE; + sc->N1_bits = sc->N1_bytes * 8; + } +} /* end of calculate_N1 */ + +/* + * Shift_N1 operation handler method + */ +bool operation_shiftn1(PnvSpiController *sc, uint8_t opcode, + xfer_buffer **payload, bool send_n1_alone) +{ + uint8_t n1_count; + bool stop = false; + + /* + * If there isn't a current payload left over from a stopped sequence + * create a new one. + */ + if (*payload == NULL) { + SPI_DEBUG(qemu_log("Creating new payload xfer_buffer\n")); + *payload = xfer_buffer_new(); + } + /* + * Use a combination of N1 counters to build the N1 portion of the + * transmit payload. + * We only care about transmit at this time since the request payload + * only represents data going out on the controller output line. + * Leave mode specific considerations in the calculate function since + * all we really care about are counters that tell use exactly how + * many bytes are in the payload and how many of those bytes to + * include from the TDR into the payload. + */ + calculate_N1(sc, opcode); + SPI_DEBUG(qemu_log("Shift N1 started..\n")); + log_all_N_counts(sc); + /* + * Zero out the N2 counters here in case there is no N2 operation following + * the N1 operation in the sequencer. This keeps leftover N2 information + * from interfering with spi_response logic. + */ + sc->N2_bits = 0; + sc->N2_bytes = 0; + sc->N2_tx = 0; + sc->N2_rx = 0; + /* + * N1_bytes is the overall size of the N1 portion of the frame regardless of + * whether N1 is used for tx, rx or both. Loop over the size to build a + * payload that is N1_bytes long. + * N1_tx is the count of bytes to take from the TDR and "shift" into the + * frame which means append those bytes to the payload for the N1 portion + * of the frame. + * If N1_tx is 0 or if the count exceeds the size of the TDR append 0xFF to + * the frame until the overall N1 count is reached. + */ + n1_count = 0; + while (n1_count < sc->N1_bytes) { + /* + * Assuming that if N1_tx is not equal to 0 then it is the same as + * N1_bytes. + */ + if ((sc->N1_tx != 0) && (n1_count < SPI_CONTROLLER_REG_SIZE)) { + + if (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1) { + /* + * Note that we are only appending to the payload IF the TDR + * is full otherwise we don't touch the payload because we are + * going to NOT send the payload and instead tell the sequencer + * that called us to stop and wait for a TDR write so we have + * data to load into the payload. + */ + uint8_t n1_byte = 0x00; + n1_byte = get_from_offset(sc, n1_count); + SPI_DEBUG(qemu_log("Extracting tx n1_byte = 0x%2.2x at index " + "%d from TDR\n", n1_byte, n1_count)); + if (sc->reverse_bits) { + SPI_DEBUG(qemu_log("Reversing bit order of tx n1_byte\n")); + n1_byte = reverse_bits8(n1_byte); + } + SPI_DEBUG(qemu_log("Appending tx n1_byte = 0x%2.2x to " + "Payload\n", n1_byte)); + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = + n1_byte; + } else { + /* + * We hit a shift_n1 opcode TX but the TDR is empty, tell the + * sequencer to stop and break this loop. + */ + SPI_DEBUG(qemu_log("Shift N1 set for transmit but TDR is empty," + " requesting sequencer stop\n")); + stop = true; + break; + } + } else { + /* + * Cases here: + * - we are receiving during the N1 frame segment and the RDR + * is full so we need to stop until the RDR is read + * - we are transmitting and we don't care about RDR status + * since we won't be loading RDR during the frame segment. + * - we are receiving and the RDR is empty so we allow the operation + * to proceed. + */ + if ((sc->N1_rx != 0) && (GETFIELD(STATUS_REG_RDR_FULL, + sc->status_reg) == 1)) { + SPI_DEBUG(qemu_log("Shift N1 set for receive but RDR is full, " + "requesting sequencer stop\n")); + stop = true; + break; + } else { + SPI_DEBUG(qemu_log("Appending tx n1_byte = 0xFF to Payload\n")); + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = 0xff; + } + } + n1_count++; + } /* end of while */ + /* + * If we are not stopping due to an empty TDR and we are doing an N1 TX + * and the TDR is full we need to clear the TDR_full status. + * Do this here instead of up in the loop above so we don't log the message + * in every loop iteration. + * Ignore the send_n1_alone flag, all that does is defer the TX until the N2 + * operation, which was found immediately after the current opcode. The TDR + * was unloaded and will be shifted so we have to clear the TDR_full status. + */ + if (!stop && (sc->N1_tx != 0) && + (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1)) { + + sc->status_reg = SETFIELD(STATUS_REG_TDR_FULL, sc->status_reg, 0); + SPI_DEBUG(qemu_log("TDR_full set to 0\n")); + } + /* + * There are other reasons why the shifter would stop, such as a TDR empty + * or RDR full condition with N1 set to receive. If we haven't stopped due + * to either one of those conditions then check if the send_n1_alone flag is + * equal to False, indicating the next opcode is an N2 operation, AND if + * the N2 counter reload switch (bit 0 of the N2 count control field) is + * set. This condition requires a pacing write to "kick" off the N2 + * shift which includes the N1 shift as well when send_n1_alone is False. + */ + if (!stop && !send_n1_alone && + (GETFIELD(PPC_BIT(52), sc->counter_config_reg) == 1)) { + SPI_DEBUG(qemu_log("N2 counter reload active, stop N1 shift, " + "TDR_underrun set to 1\n")); + stop = true; + sc->status_reg = SETFIELD(STATUS_REG_TDR_UNDERRUN, sc->status_reg, 1); + } + /* + * If send_n1_alone is set AND we have a full TDR then this is the first and + * last payload to send and we don't have an N2 frame segment to add to the + * payload. + */ + if (send_n1_alone && !stop) { + uint32_t tx; + uint32_t rx; + uint8_t *read_buf = NULL; + xfer_buffer *rsp_payload = NULL; + + /* We have a TX and a full TDR or an RX and an empty RDR */ + SPI_DEBUG(qemu_log("Shifting N1 frame: first = %d, last = %d, " + "n1 bits = %d\n", sc->first, sc->last, + sc->N1_bits)); + rsp_payload = xfer_buffer_new(); + for (int offset = 0; offset < (*payload)->len; offset = offset + 4) { + xfer_buffer_read_ptr(*payload, &read_buf, offset, 4); + tx = 0; + for (int i = 0; i < 4; i++) { + if ((offset + i) >= (*payload)->len) { + break; + } + tx = (tx << 8) | read_buf[i]; + } + rx = ssi_transfer((sc->bus).ssi_bus, tx); + for (int i = 0; i < 4; i++) { + if ((offset + i) >= (*payload)->len) { + break; + } + *(xfer_buffer_write_ptr(rsp_payload, rsp_payload->len, 1)) = + (rx >> (24 - i * 8)) & 0xFF; + } + } + if (rsp_payload != NULL) { + spi_response(sc, sc->N1_bits, rsp_payload); + } + sc->first = 0; + sc->last = 0; + /* The N1 frame shift is complete so reset the N1 counters */ + sc->N2_bits = 0; + sc->N2_bytes = 0; + sc->N2_tx = 0; + sc->N2_rx = 0; + xfer_buffer_free(*payload); + *payload = NULL; + SPI_DEBUG(qemu_log("Payload buffer freed\n")); + } else { + SPI_DEBUG(qemu_log("Not shifting N1, send_n1_alone = %d, stop = %d\n", + send_n1_alone, stop)); + } + return stop; +} /* end of operation_shiftn1() */ + +/* + * Calculate the N2 counters based on passed in opcode and + * internal register values. + * The method assumes that the opcode is a Shift_N2 opcode + * and doesn't test it. + * The counters returned are: + * N2 bits: Number of bits in the payload data that are significant + * to the responder. + * N2_bytes: Total count of payload bytes for the N2 frame. + * N2_tx: Total number of bytes taken from TDR for N2 + * N2_rx: Total number of bytes taken from the payload for N2 + */ +void calculate_N2(PnvSpiController *sc, uint8_t opcode) +{ + /* + * Shift_N2 opcode form: 0x4M + * Implicit mode: + * If M!=0 the shift count is M bytes and M is the number of rx bytes. + * Forced Implicit mode: + * M is the shift count but tx and rx is determined by the count control + * register fields. Note that we only check for Forced Implicit mode when + * M != 0 since the mode doesn't make sense when M = 0. + * Explicit mode: + * If M==0 then shift count is number of bits defined in the + * Counter Configuration Register's shift_count_N1 field. + */ + if (GETFIELD(PPC_BITMASK8(4, 7), opcode) == 0) { + /* Explicit mode */ + sc->N2_bits = GETFIELD(COUNTER_CONFIG_REG_SHIFT_COUNT_N2, + sc->counter_config_reg); + sc->N2_bytes = ceil(sc->N2_bits / 8); + sc->N2_tx = 0; + sc->N2_rx = 0; + /* If tx count control for N2 is set, load the tx value */ + if (GETFIELD(PPC_BIT(54), sc->counter_config_reg) == 1) { + sc->N2_tx = sc->N2_bytes; + } + /* If rx count control for N2 is set, load the rx value */ + if (GETFIELD(PPC_BIT(55), sc->counter_config_reg) == 1) { + sc->N2_rx = sc->N2_bytes; + } + } else { + /* Implicit mode/Forced Implicit mode, use M field from opcode */ + sc->N2_bytes = GETFIELD(PPC_BITMASK8(4, 7), opcode); + sc->N2_bits = sc->N2_bytes * 8; + /* Assume that we are going to receive the count */ + sc->N2_rx = sc->N2_bytes; + sc->N2_tx = 0; + /* Let Forced Implicit mode have an effect on the counts */ + if (GETFIELD(PPC_BIT(53), sc->counter_config_reg) == 1) { + /* + * If Forced Implicit mode and count control doesn't + * indicate a receive then reset the rx count to 0 + */ + if (GETFIELD(PPC_BIT(55), sc->counter_config_reg) == 0) { + sc->N2_rx = 0; + } + /* If tx count control for N2 is set, load the tx value */ + if (GETFIELD(PPC_BIT(54), sc->counter_config_reg) == 1) { + sc->N2_tx = sc->N2_bytes; + } + } + } + /* + * Enforce an upper limit on the size of N1 that is equal to the + * known size of the shift register, 64 bits or 72 bits if ECC + * is enabled. + * If the size exceeds 72 bits it is a user error so log an error, + * cap the size at a max of 64 bits or 72 bits and set the sequencer FSM + * error bit. + */ + uint8_t ecc_control = GETFIELD(PPC_BITMASK(29, 30), + sc->clock_config_reset_control); + if (ecc_control == 0 || ecc_control == 2) { + if (sc->N2_bytes > (SPI_CONTROLLER_REG_SIZE + 1)) { + SPI_DEBUG(qemu_log("Unsupported N2 shift size when ECC enabled, " + "bytes = 0x%x, bits = 0x%x\n", + sc->N2_bytes, sc->N2_bits)); + sc->N2_bytes = SPI_CONTROLLER_REG_SIZE + 1; + sc->N2_bits = sc->N2_bytes * 8; + } + } else if (sc->N2_bytes > SPI_CONTROLLER_REG_SIZE) { + SPI_DEBUG(qemu_log("Unsupported N2 shift size, bytes = 0x%x, " + "bits = 0x%x\n", sc->N2_bytes, sc->N2_bits)); + sc->N2_bytes = SPI_CONTROLLER_REG_SIZE; + sc->N2_bits = sc->N2_bytes * 8; + } +} /* end of calculate_N2 */ + +/* + * Shift_N2 operation handler method + */ + +bool operation_shiftn2(PnvSpiController *sc, uint8_t opcode, + xfer_buffer **payload) +{ + uint8_t n2_count; + bool stop = false; + + /* + * If there isn't a current payload left over from a stopped sequence + * create a new one. + */ + if (*payload == NULL) { + SPI_DEBUG(qemu_log("Creating new payload xfer_buffer\n")); + *payload = xfer_buffer_new(); + } + /* + * Use a combination of N2 counters to build the N2 portion of the + * transmit payload. + */ + calculate_N2(sc, opcode); + SPI_DEBUG(qemu_log("Shift N2 started\n")); + log_all_N_counts(sc); + /* + * The only difference between this code and the code for shift N1 is + * that this code has to account for the possible presence of N1 transmit + * bytes already taken from the TDR. + * If there are bytes to be transmitted for the N2 portion of the frame + * and there are still bytes in TDR that have not been copied into the + * TX data of the payload, this code will handle transmitting those + * remaining bytes. + * If for some reason the transmit count(s) add up to more than the size + * of the TDR we will just append 0xFF to the transmit payload data until + * the payload is N1 + N2 bytes long. + */ + n2_count = 0; + while (n2_count < sc->N2_bytes) { + /* + * If the RDR is full and we need to RX just bail out, letting the + * code continue will end up building the payload twice in the same + * buffer since RDR full causes a sequence stop and restart. + */ + if ((sc->N2_rx != 0) && + (GETFIELD(STATUS_REG_RDR_FULL, sc->status_reg) == 1)) { + SPI_DEBUG(qemu_log("Shift N2 set for receive but RDR is full, " + "requesting sequencer stop\n")); + stop = true; + break; + } + if ((sc->N2_tx != 0) && ((sc->N1_tx + n2_count) < + SPI_CONTROLLER_REG_SIZE)) { + /* Always append data for the N2 segment if it is set for TX */ + uint8_t n2_byte = 0x00; + n2_byte = get_from_offset(sc, (sc->N1_tx + n2_count)); + SPI_DEBUG(qemu_log("Extracting tx n2_byte = 0x%2.2x at index %d " + "from TDR\n", n2_byte, (sc->N1_tx + n2_count))); + if (sc->reverse_bits) { + SPI_DEBUG(qemu_log("Reversing bit order of tx n2_byte\n")); + n2_byte = reverse_bits8(n2_byte); + } + SPI_DEBUG(qemu_log("Appending tx n2_byte = 0x%2.2x to Payload\n", + n2_byte)); + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = n2_byte; + } else { + /* + * Regardless of whether or not N2 is set for TX or RX, we need + * the number of bytes in the payload to match the overall length + * of the operation. + */ + SPI_DEBUG(qemu_log("Appending tx n2_byte = 0xFF to Payload\n")); + *(xfer_buffer_write_ptr(*payload, (*payload)->len, 1)) = 0xff; + } + n2_count++; + } /* end of while */ + if (!stop) { + uint32_t tx; + uint32_t rx; + uint8_t *read_buf = NULL; + xfer_buffer *rsp_payload = NULL; + + /* We have a TX and a full TDR or an RX and an empty RDR */ + SPI_DEBUG(qemu_log("Shifting N2 frame: first = %d, last = %d, " + "n1+n2 bits = %d\n", sc->first, sc->last, + (sc->N1_bits + sc->N2_bits))); + rsp_payload = xfer_buffer_new(); + for (int offset = 0; offset < (*payload)->len; offset = offset + 4) { + xfer_buffer_read_ptr(*payload, &read_buf, offset, 4); + tx = 0; + for (int i = 0; i < 4; i++) { + if ((offset + i) >= (*payload)->len) { + break; + } + tx = (tx << 8) | read_buf[i]; + } + rx = ssi_transfer((sc->bus).ssi_bus, tx); + for (int i = 0; i < 4; i++) { + if ((offset + i) >= (*payload)->len) { + break; + } + *(xfer_buffer_write_ptr(rsp_payload, rsp_payload->len, 1)) = + (rx >> (24 - i * 8)) & 0xFF; + } + } + if (rsp_payload != NULL) { + spi_response(sc, (sc->N1_bits + sc->N2_bits), rsp_payload); + } + sc->first = 0; + sc->last = 0; + /* + * If we are doing an N2 TX and the TDR is full we need to clear the + * TDR_full status. Do this here instead of up in the loop above so we + * don't log the message in every loop iteration. + */ + if ((sc->N2_tx != 0) && + (GETFIELD(STATUS_REG_TDR_FULL, sc->status_reg) == 1)) { + sc->status_reg = SETFIELD(STATUS_REG_TDR_FULL, sc->status_reg, 0); + SPI_DEBUG(qemu_log("TDR_full set to 0\n")); + } + /* + * The N2 frame shift is complete so reset the N2 counters. + * Reset the N1 counters also in case the frame was a combination of + * N1 and N2 segments. + */ + sc->N2_bits = 0; + sc->N2_bytes = 0; + sc->N2_tx = 0; + sc->N2_rx = 0; + sc->N1_bits = 0; + sc->N1_bytes = 0; + sc->N1_tx = 0; + sc->N1_rx = 0; + xfer_buffer_free(*payload); + *payload = NULL; + SPI_DEBUG(qemu_log("Payload buffer freed\n")); + } else { + SPI_DEBUG(qemu_log("Not shifting N2, stop = %d\n", stop)); + } + return stop; +} /* end of operation_shiftn2()*/ + +/* + * The SPIC engine and its internal sequencer can be interrupted and reset by + * a hardware signal, the sbe_spicst_hard_reset bits from Pervasive + * Miscellaneous Register of sbe_register_bo device. + * Reset immediately aborts any SPI transaction in progress and returns the + * sequencer and state machines to idle state. + * The configuration register values are not changed. The status register is + * not reset. The engine registers are not reset. + * The SPIC engine reset does not have any affect on the attached devices. + * Reset handling of any attached devices is beyond the scope of the engine. + */ +static void do_reset(DeviceState *dev) +{ + PnvSpiController *sc = PNV_SPICONTROLLER(dev); + SPI_DEBUG(qemu_log("Resetting spic engine sequencer configuration and spi " + "communication\n")); + /* Reset all N1 and N2 counters, and other constants */ + sc->first = 0; + sc->last = 0; + sc->N2_bits = 0; + sc->N2_bytes = 0; + sc->N2_tx = 0; + sc->N2_rx = 0; + sc->N1_bits = 0; + sc->N1_bytes = 0; + sc->N1_tx = 0; + sc->N1_rx = 0; + sc->loop_counter_1 = 0; + sc->loop_counter_2 = 0; + SPI_DEBUG(qemu_log("Disconnected from responder\n")); + qemu_set_irq((sc->bus).cs_line[0], 1); +} + static void pnv_spi_bus_realize(DeviceState *dev, Error **errp) { PnvSPIBus *s = PNV_SPI_BUS(dev); @@ -191,6 +1498,7 @@ static const TypeInfo pnv_spi_bus_info = { static Property pnv_spi_controller_properties[] = { DEFINE_PROP_UINT32("spic_num", PnvSpiController, spic_num, 0), + DEFINE_PROP_BOOL("reverse_bits", PnvSpiController, reverse_bits, false), DEFINE_PROP_END_OF_LIST(), }; @@ -254,6 +1562,7 @@ static void pnv_spi_controller_class_init(ObjectClass *klass, void *data) dc->desc = "PowerNV SPI Controller"; dc->realize = pnv_spi_controller_realize; + dc->reset = do_reset; device_class_set_props(dc, pnv_spi_controller_properties); }
In this commit SPI shift engine and sequencer logic is implemented. Shift engine performs serialization and de-serialization according to the control by the sequencer and according to the setup defined in the configuration registers. Sequencer implements the main control logic and FSM to handle data transmit and data receive control of the shift engine. Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com> --- include/hw/ppc/pnv_spi_controller.h | 72 ++ hw/ppc/pnv_spi_controller.c | 1311 ++++++++++++++++++++++++++- 2 files changed, 1382 insertions(+), 1 deletion(-)