| Message ID | 20200316142928.153431-13-its@irrelevant.dk |
|---|---|
| State | New |
| Headers | show |
| Series | nvme: support NVMe v1.3d, SGLs and multiple namespaces | expand |
On Mon, 2020-03-16 at 07:28 -0700, Klaus Jensen wrote: > From: Klaus Jensen <k.jensen@samsung.com> > > Add support for the Get Log Page command and basic implementations of > the mandatory Error Information, SMART / Health Information and Firmware > Slot Information log pages. > > In violation of the specification, the SMART / Health Information log > page does not persist information over the lifetime of the controller > because the device has no place to store such persistent state. > > Note that the LPA field in the Identify Controller data structure > intentionally has bit 0 cleared because there is no namespace specific > information in the SMART / Health information log page. > > Required for compliance with NVMe revision 1.2.1. See NVM Express 1.2.1, > Section 5.10 ("Get Log Page command"). > > Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com> > Acked-by: Keith Busch <kbusch@kernel.org> > --- > hw/block/nvme.c | 138 +++++++++++++++++++++++++++++++++++++++++- > hw/block/nvme.h | 10 +++ > hw/block/trace-events | 2 + > 3 files changed, 149 insertions(+), 1 deletion(-) > > diff --git a/hw/block/nvme.c b/hw/block/nvme.c > index 64c42101df5c..83ff3fbfb463 100644 > --- a/hw/block/nvme.c > +++ b/hw/block/nvme.c > @@ -569,6 +569,138 @@ static uint16_t nvme_create_sq(NvmeCtrl *n, NvmeCmd *cmd) > return NVME_SUCCESS; > } > > +static uint16_t nvme_smart_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, > + uint64_t off, NvmeRequest *req) > +{ > + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); > + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); > + uint32_t nsid = le32_to_cpu(cmd->nsid); > + > + uint32_t trans_len; > + time_t current_ms; > + uint64_t units_read = 0, units_written = 0; > + uint64_t read_commands = 0, write_commands = 0; > + NvmeSmartLog smart; > + BlockAcctStats *s; > + > + if (nsid && nsid != 0xffffffff) { > + return NVME_INVALID_FIELD | NVME_DNR; > + } > + > + s = blk_get_stats(n->conf.blk); > + > + units_read = s->nr_bytes[BLOCK_ACCT_READ] >> BDRV_SECTOR_BITS; > + units_written = s->nr_bytes[BLOCK_ACCT_WRITE] >> BDRV_SECTOR_BITS; > + read_commands = s->nr_ops[BLOCK_ACCT_READ]; > + write_commands = s->nr_ops[BLOCK_ACCT_WRITE]; > + > + if (off > sizeof(smart)) { > + return NVME_INVALID_FIELD | NVME_DNR; > + } > + > + trans_len = MIN(sizeof(smart) - off, buf_len); > + > + memset(&smart, 0x0, sizeof(smart)); > + > + smart.data_units_read[0] = cpu_to_le64(units_read / 1000); > + smart.data_units_written[0] = cpu_to_le64(units_written / 1000); > + smart.host_read_commands[0] = cpu_to_le64(read_commands); > + smart.host_write_commands[0] = cpu_to_le64(write_commands); > + > + smart.temperature[0] = n->temperature & 0xff; > + smart.temperature[1] = (n->temperature >> 8) & 0xff; > + > + if ((n->temperature > n->features.temp_thresh_hi) || > + (n->temperature < n->features.temp_thresh_low)) { > + smart.critical_warning |= NVME_SMART_TEMPERATURE; > + } > + > + current_ms = qemu_clock_get_ms(QEMU_CLOCK_VIRTUAL); > + smart.power_on_hours[0] = > + cpu_to_le64((((current_ms - n->starttime_ms) / 1000) / 60) / 60); OH, I didn't notice that you didn't have the endian conversion in V5, it is needed here of course. > + > + return nvme_dma_read_prp(n, (uint8_t *) &smart + off, trans_len, prp1, > + prp2); > +} > + > +static uint16_t nvme_fw_log_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, > + uint64_t off, NvmeRequest *req) > +{ > + uint32_t trans_len; > + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); > + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); > + NvmeFwSlotInfoLog fw_log; > + > + if (off > sizeof(fw_log)) { > + return NVME_INVALID_FIELD | NVME_DNR; > + } > + > + memset(&fw_log, 0, sizeof(NvmeFwSlotInfoLog)); > + > + trans_len = MIN(sizeof(fw_log) - off, buf_len); > + > + return nvme_dma_read_prp(n, (uint8_t *) &fw_log + off, trans_len, prp1, > + prp2); > +} > + > +static uint16_t nvme_error_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, > + uint64_t off, NvmeRequest *req) > +{ > + uint32_t trans_len; > + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); > + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); > + uint8_t errlog[64]; I'll would replace this with sizeof(NvmeErrorLogEntry) (and add NvmeErrorLogEntry to the nvme.h), just for the sake of consistency, and in case we end up reporting some errors to the log in the future. > + > + if (off > sizeof(errlog)) { > + return NVME_INVALID_FIELD | NVME_DNR; > + } > + > + memset(errlog, 0x0, sizeof(errlog)); > + > + trans_len = MIN(sizeof(errlog) - off, buf_len); > + > + return nvme_dma_read_prp(n, errlog, trans_len, prp1, prp2); > +} Besides this, looks good now. > + > +static uint16_t nvme_get_log(NvmeCtrl *n, NvmeCmd *cmd, NvmeRequest *req) > +{ > + uint32_t dw10 = le32_to_cpu(cmd->cdw10); > + uint32_t dw11 = le32_to_cpu(cmd->cdw11); > + uint32_t dw12 = le32_to_cpu(cmd->cdw12); > + uint32_t dw13 = le32_to_cpu(cmd->cdw13); > + uint8_t lid = dw10 & 0xff; > + uint8_t rae = (dw10 >> 15) & 0x1; > + uint32_t numdl, numdu; > + uint64_t off, lpol, lpou; > + size_t len; > + > + numdl = (dw10 >> 16); > + numdu = (dw11 & 0xffff); > + lpol = dw12; > + lpou = dw13; > + > + len = (((numdu << 16) | numdl) + 1) << 2; > + off = (lpou << 32ULL) | lpol; > + > + if (off & 0x3) { > + return NVME_INVALID_FIELD | NVME_DNR; > + } > + > + trace_nvme_dev_get_log(nvme_cid(req), lid, rae, len, off); > + > + switch (lid) { > + case NVME_LOG_ERROR_INFO: > + return nvme_error_info(n, cmd, len, off, req); > + case NVME_LOG_SMART_INFO: > + return nvme_smart_info(n, cmd, len, off, req); > + case NVME_LOG_FW_SLOT_INFO: > + return nvme_fw_log_info(n, cmd, len, off, req); > + default: > + trace_nvme_dev_err_invalid_log_page(nvme_cid(req), lid); > + return NVME_INVALID_FIELD | NVME_DNR; > + } > +} > + > static void nvme_free_cq(NvmeCQueue *cq, NvmeCtrl *n) > { > n->cq[cq->cqid] = NULL; > @@ -914,6 +1046,8 @@ static uint16_t nvme_admin_cmd(NvmeCtrl *n, NvmeCmd *cmd, NvmeRequest *req) > return nvme_del_sq(n, cmd); > case NVME_ADM_CMD_CREATE_SQ: > return nvme_create_sq(n, cmd); > + case NVME_ADM_CMD_GET_LOG_PAGE: > + return nvme_get_log(n, cmd, req); > case NVME_ADM_CMD_DELETE_CQ: > return nvme_del_cq(n, cmd); > case NVME_ADM_CMD_CREATE_CQ: > @@ -1416,7 +1550,9 @@ static void nvme_init_state(NvmeCtrl *n) > n->namespaces = g_new0(NvmeNamespace, n->num_namespaces); > n->sq = g_new0(NvmeSQueue *, n->params.max_ioqpairs + 1); > n->cq = g_new0(NvmeCQueue *, n->params.max_ioqpairs + 1); > + n->temperature = NVME_TEMPERATURE; > n->features.temp_thresh_hi = NVME_TEMPERATURE_WARNING; > + n->starttime_ms = qemu_clock_get_ms(QEMU_CLOCK_VIRTUAL); > } > > static void nvme_init_cmb(NvmeCtrl *n, PCIDevice *pci_dev) > @@ -1493,7 +1629,7 @@ static void nvme_init_ctrl(NvmeCtrl *n) > */ > id->acl = 3; > id->frmw = 7 << 1; > - id->lpa = 1 << 0; > + id->lpa = 1 << 2; > > /* recommended default value (~70 C) */ > id->wctemp = cpu_to_le16(NVME_TEMPERATURE_WARNING); > diff --git a/hw/block/nvme.h b/hw/block/nvme.h > index 8cda5f02c622..ebeee2edc4f4 100644 > --- a/hw/block/nvme.h > +++ b/hw/block/nvme.h > @@ -109,6 +109,7 @@ typedef struct NvmeCtrl { > uint64_t host_timestamp; /* Timestamp sent by the host */ > uint64_t timestamp_set_qemu_clock_ms; /* QEMU clock time */ > uint16_t temperature; > + uint64_t starttime_ms; > > NvmeNamespace *namespaces; > NvmeSQueue **sq; > @@ -124,4 +125,13 @@ static inline uint64_t nvme_ns_nlbas(NvmeCtrl *n, NvmeNamespace *ns) > return n->ns_size >> nvme_ns_lbads(ns); > } > > +static inline uint16_t nvme_cid(NvmeRequest *req) > +{ > + if (req) { > + return le16_to_cpu(req->cqe.cid); > + } > + > + return 0xffff; > +} > + > #endif /* HW_NVME_H */ > diff --git a/hw/block/trace-events b/hw/block/trace-events > index ade506ea2bb2..7da088479f39 100644 > --- a/hw/block/trace-events > +++ b/hw/block/trace-events > @@ -46,6 +46,7 @@ nvme_dev_getfeat_numq(int result) "get feature number of queues, result=%d" > nvme_dev_setfeat_numq(int reqcq, int reqsq, int gotcq, int gotsq) "requested cq_count=%d sq_count=%d, responding with cq_count=%d sq_count=%d" > nvme_dev_setfeat_timestamp(uint64_t ts) "set feature timestamp = 0x%"PRIx64"" > nvme_dev_getfeat_timestamp(uint64_t ts) "get feature timestamp = 0x%"PRIx64"" > +nvme_dev_get_log(uint16_t cid, uint8_t lid, uint8_t rae, uint32_t len, uint64_t off) "cid %"PRIu16" lid 0x%"PRIx8" rae 0x%"PRIx8" len %"PRIu32" off %"PRIu64"" > nvme_dev_mmio_intm_set(uint64_t data, uint64_t new_mask) "wrote MMIO, interrupt mask set, data=0x%"PRIx64", new_mask=0x%"PRIx64"" > nvme_dev_mmio_intm_clr(uint64_t data, uint64_t new_mask) "wrote MMIO, interrupt mask clr, data=0x%"PRIx64", new_mask=0x%"PRIx64"" > nvme_dev_mmio_cfg(uint64_t data) "wrote MMIO, config controller config=0x%"PRIx64"" > @@ -85,6 +86,7 @@ nvme_dev_err_invalid_create_cq_qflags(uint16_t qflags) "failed creating completi > nvme_dev_err_invalid_identify_cns(uint16_t cns) "identify, invalid cns=0x%"PRIx16"" > nvme_dev_err_invalid_getfeat(int dw10) "invalid get features, dw10=0x%"PRIx32"" > nvme_dev_err_invalid_setfeat(uint32_t dw10) "invalid set features, dw10=0x%"PRIx32"" > +nvme_dev_err_invalid_log_page(uint16_t cid, uint16_t lid) "cid %"PRIu16" lid 0x%"PRIx16"" > nvme_dev_err_startfail_cq(void) "nvme_start_ctrl failed because there are non-admin completion queues" > nvme_dev_err_startfail_sq(void) "nvme_start_ctrl failed because there are non-admin submission queues" > nvme_dev_err_startfail_nbarasq(void) "nvme_start_ctrl failed because the admin submission queue address is null" Best regards, Maxim Levitsky
On Mar 25 12:40, Maxim Levitsky wrote: > On Mon, 2020-03-16 at 07:28 -0700, Klaus Jensen wrote: > > From: Klaus Jensen <k.jensen@samsung.com> > > > > Add support for the Get Log Page command and basic implementations of > > the mandatory Error Information, SMART / Health Information and Firmware > > Slot Information log pages. > > > > In violation of the specification, the SMART / Health Information log > > page does not persist information over the lifetime of the controller > > because the device has no place to store such persistent state. > > > > Note that the LPA field in the Identify Controller data structure > > intentionally has bit 0 cleared because there is no namespace specific > > information in the SMART / Health information log page. > > > > Required for compliance with NVMe revision 1.2.1. See NVM Express 1.2.1, > > Section 5.10 ("Get Log Page command"). > > > > Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com> > > Acked-by: Keith Busch <kbusch@kernel.org> > > --- > > hw/block/nvme.c | 138 +++++++++++++++++++++++++++++++++++++++++- > > hw/block/nvme.h | 10 +++ > > hw/block/trace-events | 2 + > > 3 files changed, 149 insertions(+), 1 deletion(-) > > > > diff --git a/hw/block/nvme.c b/hw/block/nvme.c > > index 64c42101df5c..83ff3fbfb463 100644 > > > > +static uint16_t nvme_error_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, > > + uint64_t off, NvmeRequest *req) > > +{ > > + uint32_t trans_len; > > + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); > > + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); > > + uint8_t errlog[64]; > I'll would replace this with sizeof(NvmeErrorLogEntry) > (and add NvmeErrorLogEntry to the nvme.h), just for the sake of consistency, > and in case we end up reporting some errors to the log in the future. > NvmeErrorLog is already in nvme.h; Fixed to actually use it. > > > + > > + if (off > sizeof(errlog)) { > > + return NVME_INVALID_FIELD | NVME_DNR; > > + } > > + > > + memset(errlog, 0x0, sizeof(errlog)); > > + > > + trans_len = MIN(sizeof(errlog) - off, buf_len); > > + > > + return nvme_dma_read_prp(n, errlog, trans_len, prp1, prp2); > > +} > Besides this, looks good now. > > > Best regards, > Maxim Levitsky >
On Tue, 2020-03-31 at 07:41 +0200, Klaus Birkelund Jensen wrote: > On Mar 25 12:40, Maxim Levitsky wrote: > > On Mon, 2020-03-16 at 07:28 -0700, Klaus Jensen wrote: > > > From: Klaus Jensen <k.jensen@samsung.com> > > > > > > Add support for the Get Log Page command and basic implementations of > > > the mandatory Error Information, SMART / Health Information and Firmware > > > Slot Information log pages. > > > > > > In violation of the specification, the SMART / Health Information log > > > page does not persist information over the lifetime of the controller > > > because the device has no place to store such persistent state. > > > > > > Note that the LPA field in the Identify Controller data structure > > > intentionally has bit 0 cleared because there is no namespace specific > > > information in the SMART / Health information log page. > > > > > > Required for compliance with NVMe revision 1.2.1. See NVM Express 1.2.1, > > > Section 5.10 ("Get Log Page command"). > > > > > > Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com> > > > Acked-by: Keith Busch <kbusch@kernel.org> > > > --- > > > hw/block/nvme.c | 138 +++++++++++++++++++++++++++++++++++++++++- > > > hw/block/nvme.h | 10 +++ > > > hw/block/trace-events | 2 + > > > 3 files changed, 149 insertions(+), 1 deletion(-) > > > > > > diff --git a/hw/block/nvme.c b/hw/block/nvme.c > > > index 64c42101df5c..83ff3fbfb463 100644 > > > > > > +static uint16_t nvme_error_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, > > > + uint64_t off, NvmeRequest *req) > > > +{ > > > + uint32_t trans_len; > > > + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); > > > + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); > > > + uint8_t errlog[64]; > > > > I'll would replace this with sizeof(NvmeErrorLogEntry) > > (and add NvmeErrorLogEntry to the nvme.h), just for the sake of consistency, > > and in case we end up reporting some errors to the log in the future. > > > > NvmeErrorLog is already in nvme.h; Fixed to actually use it. True that! I'll would rename it to NvmeErrorLogEntry to be honest (in that patch that added many nvme spec changes) but I don't mind keeping it as is as well. > > > > > > + > > > + if (off > sizeof(errlog)) { > > > + return NVME_INVALID_FIELD | NVME_DNR; > > > + } > > > + > > > + memset(errlog, 0x0, sizeof(errlog)); > > > + > > > + trans_len = MIN(sizeof(errlog) - off, buf_len); > > > + > > > + return nvme_dma_read_prp(n, errlog, trans_len, prp1, prp2); > > > +} > > > > Besides this, looks good now. > > > > > > Best regards, > > Maxim Levitsky > > > > Best regards, Maxim Levitsky
On Mar 31 12:45, Maxim Levitsky wrote: > On Tue, 2020-03-31 at 07:41 +0200, Klaus Birkelund Jensen wrote: > > On Mar 25 12:40, Maxim Levitsky wrote: > > > On Mon, 2020-03-16 at 07:28 -0700, Klaus Jensen wrote: > > > > From: Klaus Jensen <k.jensen@samsung.com> > > > > > > > > Add support for the Get Log Page command and basic implementations of > > > > the mandatory Error Information, SMART / Health Information and Firmware > > > > Slot Information log pages. > > > > > > > > In violation of the specification, the SMART / Health Information log > > > > page does not persist information over the lifetime of the controller > > > > because the device has no place to store such persistent state. > > > > > > > > Note that the LPA field in the Identify Controller data structure > > > > intentionally has bit 0 cleared because there is no namespace specific > > > > information in the SMART / Health information log page. > > > > > > > > Required for compliance with NVMe revision 1.2.1. See NVM Express 1.2.1, > > > > Section 5.10 ("Get Log Page command"). > > > > > > > > Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com> > > > > Acked-by: Keith Busch <kbusch@kernel.org> > > > > --- > > > > hw/block/nvme.c | 138 +++++++++++++++++++++++++++++++++++++++++- > > > > hw/block/nvme.h | 10 +++ > > > > hw/block/trace-events | 2 + > > > > 3 files changed, 149 insertions(+), 1 deletion(-) > > > > > > > > diff --git a/hw/block/nvme.c b/hw/block/nvme.c > > > > index 64c42101df5c..83ff3fbfb463 100644 > > > > > > > > +static uint16_t nvme_error_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, > > > > + uint64_t off, NvmeRequest *req) > > > > +{ > > > > + uint32_t trans_len; > > > > + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); > > > > + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); > > > > + uint8_t errlog[64]; > > > > > > I'll would replace this with sizeof(NvmeErrorLogEntry) > > > (and add NvmeErrorLogEntry to the nvme.h), just for the sake of consistency, > > > and in case we end up reporting some errors to the log in the future. > > > > > > > NvmeErrorLog is already in nvme.h; Fixed to actually use it. > True that! I'll would rename it to NvmeErrorLogEntry to be honest > (in that patch that added many nvme spec changes) but I don't mind > keeping it as is as well. > It is used in the block driver (block/nvme.c) as well, and I'd rather not involved that too much in this series.
On Tue, 2020-03-31 at 14:49 +0200, Klaus Birkelund Jensen wrote: > On Mar 31 12:45, Maxim Levitsky wrote: > > On Tue, 2020-03-31 at 07:41 +0200, Klaus Birkelund Jensen wrote: > > > On Mar 25 12:40, Maxim Levitsky wrote: > > > > On Mon, 2020-03-16 at 07:28 -0700, Klaus Jensen wrote: > > > > > From: Klaus Jensen <k.jensen@samsung.com> > > > > > > > > > > Add support for the Get Log Page command and basic implementations of > > > > > the mandatory Error Information, SMART / Health Information and Firmware > > > > > Slot Information log pages. > > > > > > > > > > In violation of the specification, the SMART / Health Information log > > > > > page does not persist information over the lifetime of the controller > > > > > because the device has no place to store such persistent state. > > > > > > > > > > Note that the LPA field in the Identify Controller data structure > > > > > intentionally has bit 0 cleared because there is no namespace specific > > > > > information in the SMART / Health information log page. > > > > > > > > > > Required for compliance with NVMe revision 1.2.1. See NVM Express 1.2.1, > > > > > Section 5.10 ("Get Log Page command"). > > > > > > > > > > Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com> > > > > > Acked-by: Keith Busch <kbusch@kernel.org> > > > > > --- > > > > > hw/block/nvme.c | 138 +++++++++++++++++++++++++++++++++++++++++- > > > > > hw/block/nvme.h | 10 +++ > > > > > hw/block/trace-events | 2 + > > > > > 3 files changed, 149 insertions(+), 1 deletion(-) > > > > > > > > > > diff --git a/hw/block/nvme.c b/hw/block/nvme.c > > > > > index 64c42101df5c..83ff3fbfb463 100644 > > > > > > > > > > +static uint16_t nvme_error_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, > > > > > + uint64_t off, NvmeRequest *req) > > > > > +{ > > > > > + uint32_t trans_len; > > > > > + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); > > > > > + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); > > > > > + uint8_t errlog[64]; > > > > > > > > I'll would replace this with sizeof(NvmeErrorLogEntry) > > > > (and add NvmeErrorLogEntry to the nvme.h), just for the sake of consistency, > > > > and in case we end up reporting some errors to the log in the future. > > > > > > > > > > NvmeErrorLog is already in nvme.h; Fixed to actually use it. > > > > True that! I'll would rename it to NvmeErrorLogEntry to be honest > > (in that patch that added many nvme spec changes) but I don't mind > > keeping it as is as well. > > > > > It is used in the block driver (block/nvme.c) as well, and I'd rather > not involved that too much in this series. All right, this can always be done later. Best regards, Maxim Levitsky >
diff --git a/hw/block/nvme.c b/hw/block/nvme.c index 64c42101df5c..83ff3fbfb463 100644 --- a/hw/block/nvme.c +++ b/hw/block/nvme.c @@ -569,6 +569,138 @@ static uint16_t nvme_create_sq(NvmeCtrl *n, NvmeCmd *cmd) return NVME_SUCCESS; } +static uint16_t nvme_smart_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, + uint64_t off, NvmeRequest *req) +{ + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); + uint32_t nsid = le32_to_cpu(cmd->nsid); + + uint32_t trans_len; + time_t current_ms; + uint64_t units_read = 0, units_written = 0; + uint64_t read_commands = 0, write_commands = 0; + NvmeSmartLog smart; + BlockAcctStats *s; + + if (nsid && nsid != 0xffffffff) { + return NVME_INVALID_FIELD | NVME_DNR; + } + + s = blk_get_stats(n->conf.blk); + + units_read = s->nr_bytes[BLOCK_ACCT_READ] >> BDRV_SECTOR_BITS; + units_written = s->nr_bytes[BLOCK_ACCT_WRITE] >> BDRV_SECTOR_BITS; + read_commands = s->nr_ops[BLOCK_ACCT_READ]; + write_commands = s->nr_ops[BLOCK_ACCT_WRITE]; + + if (off > sizeof(smart)) { + return NVME_INVALID_FIELD | NVME_DNR; + } + + trans_len = MIN(sizeof(smart) - off, buf_len); + + memset(&smart, 0x0, sizeof(smart)); + + smart.data_units_read[0] = cpu_to_le64(units_read / 1000); + smart.data_units_written[0] = cpu_to_le64(units_written / 1000); + smart.host_read_commands[0] = cpu_to_le64(read_commands); + smart.host_write_commands[0] = cpu_to_le64(write_commands); + + smart.temperature[0] = n->temperature & 0xff; + smart.temperature[1] = (n->temperature >> 8) & 0xff; + + if ((n->temperature > n->features.temp_thresh_hi) || + (n->temperature < n->features.temp_thresh_low)) { + smart.critical_warning |= NVME_SMART_TEMPERATURE; + } + + current_ms = qemu_clock_get_ms(QEMU_CLOCK_VIRTUAL); + smart.power_on_hours[0] = + cpu_to_le64((((current_ms - n->starttime_ms) / 1000) / 60) / 60); + + return nvme_dma_read_prp(n, (uint8_t *) &smart + off, trans_len, prp1, + prp2); +} + +static uint16_t nvme_fw_log_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, + uint64_t off, NvmeRequest *req) +{ + uint32_t trans_len; + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); + NvmeFwSlotInfoLog fw_log; + + if (off > sizeof(fw_log)) { + return NVME_INVALID_FIELD | NVME_DNR; + } + + memset(&fw_log, 0, sizeof(NvmeFwSlotInfoLog)); + + trans_len = MIN(sizeof(fw_log) - off, buf_len); + + return nvme_dma_read_prp(n, (uint8_t *) &fw_log + off, trans_len, prp1, + prp2); +} + +static uint16_t nvme_error_info(NvmeCtrl *n, NvmeCmd *cmd, uint32_t buf_len, + uint64_t off, NvmeRequest *req) +{ + uint32_t trans_len; + uint64_t prp1 = le64_to_cpu(cmd->dptr.prp1); + uint64_t prp2 = le64_to_cpu(cmd->dptr.prp2); + uint8_t errlog[64]; + + if (off > sizeof(errlog)) { + return NVME_INVALID_FIELD | NVME_DNR; + } + + memset(errlog, 0x0, sizeof(errlog)); + + trans_len = MIN(sizeof(errlog) - off, buf_len); + + return nvme_dma_read_prp(n, errlog, trans_len, prp1, prp2); +} + +static uint16_t nvme_get_log(NvmeCtrl *n, NvmeCmd *cmd, NvmeRequest *req) +{ + uint32_t dw10 = le32_to_cpu(cmd->cdw10); + uint32_t dw11 = le32_to_cpu(cmd->cdw11); + uint32_t dw12 = le32_to_cpu(cmd->cdw12); + uint32_t dw13 = le32_to_cpu(cmd->cdw13); + uint8_t lid = dw10 & 0xff; + uint8_t rae = (dw10 >> 15) & 0x1; + uint32_t numdl, numdu; + uint64_t off, lpol, lpou; + size_t len; + + numdl = (dw10 >> 16); + numdu = (dw11 & 0xffff); + lpol = dw12; + lpou = dw13; + + len = (((numdu << 16) | numdl) + 1) << 2; + off = (lpou << 32ULL) | lpol; + + if (off & 0x3) { + return NVME_INVALID_FIELD | NVME_DNR; + } + + trace_nvme_dev_get_log(nvme_cid(req), lid, rae, len, off); + + switch (lid) { + case NVME_LOG_ERROR_INFO: + return nvme_error_info(n, cmd, len, off, req); + case NVME_LOG_SMART_INFO: + return nvme_smart_info(n, cmd, len, off, req); + case NVME_LOG_FW_SLOT_INFO: + return nvme_fw_log_info(n, cmd, len, off, req); + default: + trace_nvme_dev_err_invalid_log_page(nvme_cid(req), lid); + return NVME_INVALID_FIELD | NVME_DNR; + } +} + static void nvme_free_cq(NvmeCQueue *cq, NvmeCtrl *n) { n->cq[cq->cqid] = NULL; @@ -914,6 +1046,8 @@ static uint16_t nvme_admin_cmd(NvmeCtrl *n, NvmeCmd *cmd, NvmeRequest *req) return nvme_del_sq(n, cmd); case NVME_ADM_CMD_CREATE_SQ: return nvme_create_sq(n, cmd); + case NVME_ADM_CMD_GET_LOG_PAGE: + return nvme_get_log(n, cmd, req); case NVME_ADM_CMD_DELETE_CQ: return nvme_del_cq(n, cmd); case NVME_ADM_CMD_CREATE_CQ: @@ -1416,7 +1550,9 @@ static void nvme_init_state(NvmeCtrl *n) n->namespaces = g_new0(NvmeNamespace, n->num_namespaces); n->sq = g_new0(NvmeSQueue *, n->params.max_ioqpairs + 1); n->cq = g_new0(NvmeCQueue *, n->params.max_ioqpairs + 1); + n->temperature = NVME_TEMPERATURE; n->features.temp_thresh_hi = NVME_TEMPERATURE_WARNING; + n->starttime_ms = qemu_clock_get_ms(QEMU_CLOCK_VIRTUAL); } static void nvme_init_cmb(NvmeCtrl *n, PCIDevice *pci_dev) @@ -1493,7 +1629,7 @@ static void nvme_init_ctrl(NvmeCtrl *n) */ id->acl = 3; id->frmw = 7 << 1; - id->lpa = 1 << 0; + id->lpa = 1 << 2; /* recommended default value (~70 C) */ id->wctemp = cpu_to_le16(NVME_TEMPERATURE_WARNING); diff --git a/hw/block/nvme.h b/hw/block/nvme.h index 8cda5f02c622..ebeee2edc4f4 100644 --- a/hw/block/nvme.h +++ b/hw/block/nvme.h @@ -109,6 +109,7 @@ typedef struct NvmeCtrl { uint64_t host_timestamp; /* Timestamp sent by the host */ uint64_t timestamp_set_qemu_clock_ms; /* QEMU clock time */ uint16_t temperature; + uint64_t starttime_ms; NvmeNamespace *namespaces; NvmeSQueue **sq; @@ -124,4 +125,13 @@ static inline uint64_t nvme_ns_nlbas(NvmeCtrl *n, NvmeNamespace *ns) return n->ns_size >> nvme_ns_lbads(ns); } +static inline uint16_t nvme_cid(NvmeRequest *req) +{ + if (req) { + return le16_to_cpu(req->cqe.cid); + } + + return 0xffff; +} + #endif /* HW_NVME_H */ diff --git a/hw/block/trace-events b/hw/block/trace-events index ade506ea2bb2..7da088479f39 100644 --- a/hw/block/trace-events +++ b/hw/block/trace-events @@ -46,6 +46,7 @@ nvme_dev_getfeat_numq(int result) "get feature number of queues, result=%d" nvme_dev_setfeat_numq(int reqcq, int reqsq, int gotcq, int gotsq) "requested cq_count=%d sq_count=%d, responding with cq_count=%d sq_count=%d" nvme_dev_setfeat_timestamp(uint64_t ts) "set feature timestamp = 0x%"PRIx64"" nvme_dev_getfeat_timestamp(uint64_t ts) "get feature timestamp = 0x%"PRIx64"" +nvme_dev_get_log(uint16_t cid, uint8_t lid, uint8_t rae, uint32_t len, uint64_t off) "cid %"PRIu16" lid 0x%"PRIx8" rae 0x%"PRIx8" len %"PRIu32" off %"PRIu64"" nvme_dev_mmio_intm_set(uint64_t data, uint64_t new_mask) "wrote MMIO, interrupt mask set, data=0x%"PRIx64", new_mask=0x%"PRIx64"" nvme_dev_mmio_intm_clr(uint64_t data, uint64_t new_mask) "wrote MMIO, interrupt mask clr, data=0x%"PRIx64", new_mask=0x%"PRIx64"" nvme_dev_mmio_cfg(uint64_t data) "wrote MMIO, config controller config=0x%"PRIx64"" @@ -85,6 +86,7 @@ nvme_dev_err_invalid_create_cq_qflags(uint16_t qflags) "failed creating completi nvme_dev_err_invalid_identify_cns(uint16_t cns) "identify, invalid cns=0x%"PRIx16"" nvme_dev_err_invalid_getfeat(int dw10) "invalid get features, dw10=0x%"PRIx32"" nvme_dev_err_invalid_setfeat(uint32_t dw10) "invalid set features, dw10=0x%"PRIx32"" +nvme_dev_err_invalid_log_page(uint16_t cid, uint16_t lid) "cid %"PRIu16" lid 0x%"PRIx16"" nvme_dev_err_startfail_cq(void) "nvme_start_ctrl failed because there are non-admin completion queues" nvme_dev_err_startfail_sq(void) "nvme_start_ctrl failed because there are non-admin submission queues" nvme_dev_err_startfail_nbarasq(void) "nvme_start_ctrl failed because the admin submission queue address is null"