diff mbox

[V6,07/32] pci/bridge: clean up of pci_bridge_initfn()

Message ID 1256905286-25435-8-git-send-email-yamahata@valinux.co.jp
State New
Headers show

Commit Message

Isaku Yamahata Oct. 30, 2009, 12:21 p.m. UTC 
- use symbolic constant
- use helper function pci_set_xxx()
- removed lines which initializes to 0.
  It is unnecessary because it is already zeroed.
- add some comments on command registers.

Some initial values are suspicious because they seems to
be specific to apb_pci.c which is the only user of pci bridge right now.
For now don't touch those values to avoid breakage.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
---
 hw/pci.c |   36 +++++++++++++++++++++++++-----------
 1 files changed, 25 insertions(+), 11 deletions(-)
diff mbox

Patch

diff --git a/hw/pci.c b/hw/pci.c
index ab5eff8..6abb0e2 100644
--- a/hw/pci.c
+++ b/hw/pci.c
@@ -922,17 +922,31 @@  static int pci_bridge_initfn(PCIDevice *dev)
     pci_config_set_vendor_id(s->dev.config, s->vid);
     pci_config_set_device_id(s->dev.config, s->did);
 
-    s->dev.config[0x04] = 0x06; // command = bus master, pci mem
-    s->dev.config[0x05] = 0x00;
-    s->dev.config[0x06] = 0xa0; // status = fast back-to-back, 66MHz, no error
-    s->dev.config[0x07] = 0x00; // status = fast devsel
-    s->dev.config[0x08] = 0x00; // revision
-    s->dev.config[0x09] = 0x00; // programming i/f
-    pci_config_set_class(s->dev.config, PCI_CLASS_BRIDGE_PCI);
-    s->dev.config[0x0D] = 0x10; // latency_timer
-    s->dev.config[PCI_HEADER_TYPE] =
-        PCI_HEADER_TYPE_MULTI_FUNCTION | PCI_HEADER_TYPE_BRIDGE; // header_type
-    s->dev.config[0x1E] = 0xa0; // secondary status
+    /* TODO: intial value
+     * command register:
+     * According to PCI bridge spec, after reset
+     *   bus master bit is off
+     *   memory space enable bit is off
+     * According to manual (805-1251.pdf).(See abp_pbi.c for its links.)
+     *   the reset value should be zero unless the boot pin is tied high
+     *   (which is tru) and thus it should be PCI_COMMAND_MEMORY.
+     *
+     * For now, don't touch the value.
+     * Later command register will be set to zero and apb_pci.c will
+     * override the value.
+     * Same for latency timer, and multi function bit of header type.
+     */
+    pci_set_word(dev->config + PCI_COMMAND,
+                 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+    pci_set_word(dev->config + PCI_STATUS,
+                 PCI_STATUS_66MHZ | PCI_STATUS_FAST_BACK);
+    pci_config_set_class(dev->config, PCI_CLASS_BRIDGE_PCI);
+    dev->config[PCI_LATENCY_TIMER] = 0x10;
+    dev->config[PCI_HEADER_TYPE] =
+        PCI_HEADER_TYPE_MULTI_FUNCTION | PCI_HEADER_TYPE_BRIDGE;
+    pci_set_word(dev->config + PCI_SEC_STATUS,
+                 PCI_STATUS_66MHZ | PCI_STATUS_FAST_BACK);
     return 0;
 }