diff --git a/arch/powerpc/boot/4xx.c b/arch/powerpc/boot/4xx.c
index 00c4d843a023..682ca3827892 100644
--- a/arch/powerpc/boot/4xx.c
+++ b/arch/powerpc/boot/4xx.c
@@ -253,7 +253,6 @@ void ibm4xx_denali_fixup_memsize(void)
 	dt_fixup_memory(0, memsize);
 }
 
-#define SPRN_DBCR0_40X 0x3F2
 #define SPRN_DBCR0_44X 0x134
 #define DBCR0_RST_SYSTEM 0x30000000
 
@@ -270,18 +269,6 @@ void ibm44x_dbcr_reset(void)
 
 }
 
-void ibm40x_dbcr_reset(void)
-{
-	unsigned long tmp;
-
-	asm volatile (
-		"mfspr	%0,%1\n"
-		"oris	%0,%0,%2@h\n"
-		"mtspr	%1,%0"
-		: "=&r"(tmp) : "i"(SPRN_DBCR0_40X), "i"(DBCR0_RST_SYSTEM)
-		);
-}
-
 #define EMAC_RESET 0x20000000
 void ibm4xx_quiesce_eth(u32 *emac0, u32 *emac1)
 {
@@ -544,256 +531,3 @@ void ibm440spe_fixup_clocks(unsigned int sys_clk,
 	eplike_fixup_uart_clk(1, "/plb/opb/serial@f0000300", ser_clk, plb_clk);
 	eplike_fixup_uart_clk(2, "/plb/opb/serial@f0000600", ser_clk, plb_clk);
 }
-
-void ibm405gp_fixup_clocks(unsigned int sys_clk, unsigned int ser_clk)
-{
-	u32 pllmr = mfdcr(DCRN_CPC0_PLLMR);
-	u32 cpc0_cr0 = mfdcr(DCRN_405_CPC0_CR0);
-	u32 cpc0_cr1 = mfdcr(DCRN_405_CPC0_CR1);
-	u32 psr = mfdcr(DCRN_405_CPC0_PSR);
-	u32 cpu, plb, opb, ebc, tb, uart0, uart1, m;
-	u32 fwdv, fwdvb, fbdv, cbdv, opdv, epdv, ppdv, udiv;
-
-	fwdv = (8 - ((pllmr & 0xe0000000) >> 29));
-	fbdv = (pllmr & 0x1e000000) >> 25;
-	if (fbdv == 0)
-		fbdv = 16;
-	cbdv = ((pllmr & 0x00060000) >> 17) + 1; /* CPU:PLB */
-	opdv = ((pllmr & 0x00018000) >> 15) + 1; /* PLB:OPB */
-	ppdv = ((pllmr & 0x00006000) >> 13) + 1; /* PLB:PCI */
-	epdv = ((pllmr & 0x00001800) >> 11) + 2; /* PLB:EBC */
-	udiv = ((cpc0_cr0 & 0x3e) >> 1) + 1;
-
-	/* check for 405GPr */
-	if ((mfpvr() & 0xfffffff0) == (0x50910951 & 0xfffffff0)) {
-		fwdvb = 8 - (pllmr & 0x00000007);
-		if (!(psr & 0x00001000)) /* PCI async mode enable == 0 */
-			if (psr & 0x00000020) /* New mode enable */
-				m = fwdvb * 2 * ppdv;
-			else
-				m = fwdvb * cbdv * ppdv;
-		else if (psr & 0x00000020) /* New mode enable */
-			if (psr & 0x00000800) /* PerClk synch mode */
-				m = fwdvb * 2 * epdv;
-			else
-				m = fbdv * fwdv;
-		else if (epdv == fbdv)
-			m = fbdv * cbdv * epdv;
-		else
-			m = fbdv * fwdvb * cbdv;
-
-		cpu = sys_clk * m / fwdv;
-		plb = sys_clk * m / (fwdvb * cbdv);
-	} else {
-		m = fwdv * fbdv * cbdv;
-		cpu = sys_clk * m / fwdv;
-		plb = cpu / cbdv;
-	}
-	opb = plb / opdv;
-	ebc = plb / epdv;
-
-	if (cpc0_cr0 & 0x80)
-		/* uart0 uses the external clock */
-		uart0 = ser_clk;
-	else
-		uart0 = cpu / udiv;
-
-	if (cpc0_cr0 & 0x40)
-		/* uart1 uses the external clock */
-		uart1 = ser_clk;
-	else
-		uart1 = cpu / udiv;
-
-	/* setup the timebase clock to tick at the cpu frequency */
-	cpc0_cr1 = cpc0_cr1 & ~0x00800000;
-	mtdcr(DCRN_405_CPC0_CR1, cpc0_cr1);
-	tb = cpu;
-
-	dt_fixup_cpu_clocks(cpu, tb, 0);
-	dt_fixup_clock("/plb", plb);
-	dt_fixup_clock("/plb/opb", opb);
-	dt_fixup_clock("/plb/ebc", ebc);
-	dt_fixup_clock("/plb/opb/serial@ef600300", uart0);
-	dt_fixup_clock("/plb/opb/serial@ef600400", uart1);
-}
-
-
-void ibm405ep_fixup_clocks(unsigned int sys_clk)
-{
-	u32 pllmr0 = mfdcr(DCRN_CPC0_PLLMR0);
-	u32 pllmr1 = mfdcr(DCRN_CPC0_PLLMR1);
-	u32 cpc0_ucr = mfdcr(DCRN_CPC0_UCR);
-	u32 cpu, plb, opb, ebc, uart0, uart1;
-	u32 fwdva, fwdvb, fbdv, cbdv, opdv, epdv;
-	u32 pllmr0_ccdv, tb, m;
-
-	fwdva = 8 - ((pllmr1 & 0x00070000) >> 16);
-	fwdvb = 8 - ((pllmr1 & 0x00007000) >> 12);
-	fbdv = (pllmr1 & 0x00f00000) >> 20;
-	if (fbdv == 0)
-		fbdv = 16;
-
-	cbdv = ((pllmr0 & 0x00030000) >> 16) + 1; /* CPU:PLB */
-	epdv = ((pllmr0 & 0x00000300) >> 8) + 2;  /* PLB:EBC */
-	opdv = ((pllmr0 & 0x00003000) >> 12) + 1; /* PLB:OPB */
-
-	m = fbdv * fwdvb;
-
-	pllmr0_ccdv = ((pllmr0 & 0x00300000) >> 20) + 1;
-	if (pllmr1 & 0x80000000)
-		cpu = sys_clk * m / (fwdva * pllmr0_ccdv);
-	else
-		cpu = sys_clk / pllmr0_ccdv;
-
-	plb = cpu / cbdv;
-	opb = plb / opdv;
-	ebc = plb / epdv;
-	tb = cpu;
-	uart0 = cpu / (cpc0_ucr & 0x0000007f);
-	uart1 = cpu / ((cpc0_ucr & 0x00007f00) >> 8);
-
-	dt_fixup_cpu_clocks(cpu, tb, 0);
-	dt_fixup_clock("/plb", plb);
-	dt_fixup_clock("/plb/opb", opb);
-	dt_fixup_clock("/plb/ebc", ebc);
-	dt_fixup_clock("/plb/opb/serial@ef600300", uart0);
-	dt_fixup_clock("/plb/opb/serial@ef600400", uart1);
-}
-
-static u8 ibm405ex_fwdv_multi_bits[] = {
-	/* values for:  1 - 16 */
-	0x01, 0x02, 0x0e, 0x09, 0x04, 0x0b, 0x10, 0x0d, 0x0c, 0x05,
-	0x06, 0x0f, 0x0a, 0x07, 0x08, 0x03
-};
-
-u32 ibm405ex_get_fwdva(unsigned long cpr_fwdv)
-{
-	u32 index;
-
-	for (index = 0; index < ARRAY_SIZE(ibm405ex_fwdv_multi_bits); index++)
-		if (cpr_fwdv == (u32)ibm405ex_fwdv_multi_bits[index])
-			return index + 1;
-
-	return 0;
-}
-
-static u8 ibm405ex_fbdv_multi_bits[] = {
-	/* values for:  1 - 100 */
-	0x00, 0xff, 0x7e, 0xfd, 0x7a, 0xf5, 0x6a, 0xd5, 0x2a, 0xd4,
-	0x29, 0xd3, 0x26, 0xcc, 0x19, 0xb3, 0x67, 0xce, 0x1d, 0xbb,
-	0x77, 0xee, 0x5d, 0xba, 0x74, 0xe9, 0x52, 0xa5, 0x4b, 0x96,
-	0x2c, 0xd8, 0x31, 0xe3, 0x46, 0x8d, 0x1b, 0xb7, 0x6f, 0xde,
-	0x3d, 0xfb, 0x76, 0xed, 0x5a, 0xb5, 0x6b, 0xd6, 0x2d, 0xdb,
-	0x36, 0xec, 0x59, 0xb2, 0x64, 0xc9, 0x12, 0xa4, 0x48, 0x91,
-	0x23, 0xc7, 0x0e, 0x9c, 0x38, 0xf0, 0x61, 0xc2, 0x05, 0x8b,
-	0x17, 0xaf, 0x5f, 0xbe, 0x7c, 0xf9, 0x72, 0xe5, 0x4a, 0x95,
-	0x2b, 0xd7, 0x2e, 0xdc, 0x39, 0xf3, 0x66, 0xcd, 0x1a, 0xb4,
-	0x68, 0xd1, 0x22, 0xc4, 0x09, 0x93, 0x27, 0xcf, 0x1e, 0xbc,
-	/* values for:  101 - 200 */
-	0x78, 0xf1, 0x62, 0xc5, 0x0a, 0x94, 0x28, 0xd0, 0x21, 0xc3,
-	0x06, 0x8c, 0x18, 0xb0, 0x60, 0xc1, 0x02, 0x84, 0x08, 0x90,
-	0x20, 0xc0, 0x01, 0x83, 0x07, 0x8f, 0x1f, 0xbf, 0x7f, 0xfe,
-	0x7d, 0xfa, 0x75, 0xea, 0x55, 0xaa, 0x54, 0xa9, 0x53, 0xa6,
-	0x4c, 0x99, 0x33, 0xe7, 0x4e, 0x9d, 0x3b, 0xf7, 0x6e, 0xdd,
-	0x3a, 0xf4, 0x69, 0xd2, 0x25, 0xcb, 0x16, 0xac, 0x58, 0xb1,
-	0x63, 0xc6, 0x0d, 0x9b, 0x37, 0xef, 0x5e, 0xbd, 0x7b, 0xf6,
-	0x6d, 0xda, 0x35, 0xeb, 0x56, 0xad, 0x5b, 0xb6, 0x6c, 0xd9,
-	0x32, 0xe4, 0x49, 0x92, 0x24, 0xc8, 0x11, 0xa3, 0x47, 0x8e,
-	0x1c, 0xb8, 0x70, 0xe1, 0x42, 0x85, 0x0b, 0x97, 0x2f, 0xdf,
-	/* values for:  201 - 255 */
-	0x3e, 0xfc, 0x79, 0xf2, 0x65, 0xca, 0x15, 0xab, 0x57, 0xae,
-	0x5c, 0xb9, 0x73, 0xe6, 0x4d, 0x9a, 0x34, 0xe8, 0x51, 0xa2,
-	0x44, 0x89, 0x13, 0xa7, 0x4f, 0x9e, 0x3c, 0xf8, 0x71, 0xe2,
-	0x45, 0x8a, 0x14, 0xa8, 0x50, 0xa1, 0x43, 0x86, 0x0c, 0x98,
-	0x30, 0xe0, 0x41, 0x82, 0x04, 0x88, 0x10, 0xa0, 0x40, 0x81,
-	0x03, 0x87, 0x0f, 0x9f, 0x3f  /* END */
-};
-
-u32 ibm405ex_get_fbdv(unsigned long cpr_fbdv)
-{
-	u32 index;
-
-	for (index = 0; index < ARRAY_SIZE(ibm405ex_fbdv_multi_bits); index++)
-		if (cpr_fbdv == (u32)ibm405ex_fbdv_multi_bits[index])
-			return index + 1;
-
-	return 0;
-}
-
-void ibm405ex_fixup_clocks(unsigned int sys_clk, unsigned int uart_clk)
-{
-	/* PLL config */
-	u32 pllc  = CPR0_READ(DCRN_CPR0_PLLC);
-	u32 plld  = CPR0_READ(DCRN_CPR0_PLLD);
-	u32 cpud  = CPR0_READ(DCRN_CPR0_PRIMAD);
-	u32 plbd  = CPR0_READ(DCRN_CPR0_PRIMBD);
-	u32 opbd  = CPR0_READ(DCRN_CPR0_OPBD);
-	u32 perd  = CPR0_READ(DCRN_CPR0_PERD);
-
-	/* Dividers */
-	u32 fbdv   = ibm405ex_get_fbdv(__fix_zero((plld >> 24) & 0xff, 1));
-
-	u32 fwdva  = ibm405ex_get_fwdva(__fix_zero((plld >> 16) & 0x0f, 1));
-
-	u32 cpudv0 = __fix_zero((cpud >> 24) & 7, 8);
-
-	/* PLBDV0 is hardwared to 010. */
-	u32 plbdv0 = 2;
-	u32 plb2xdv0 = __fix_zero((plbd >> 16) & 7, 8);
-
-	u32 opbdv0 = __fix_zero((opbd >> 24) & 3, 4);
-
-	u32 perdv0 = __fix_zero((perd >> 24) & 3, 4);
-
-	/* Resulting clocks */
-	u32 cpu, plb, opb, ebc, vco, tb, uart0, uart1;
-
-	/* PLL's VCO is the source for primary forward ? */
-	if (pllc & 0x40000000) {
-		u32 m;
-
-		/* Feedback path */
-		switch ((pllc >> 24) & 7) {
-		case 0:
-			/* PLLOUTx */
-			m = fbdv;
-			break;
-		case 1:
-			/* CPU */
-			m = fbdv * fwdva * cpudv0;
-			break;
-		case 5:
-			/* PERClk */
-			m = fbdv * fwdva * plb2xdv0 * plbdv0 * opbdv0 * perdv0;
-			break;
-		default:
-			printf("WARNING ! Invalid PLL feedback source !\n");
-			goto bypass;
-		}
-
-		vco = (unsigned int)(sys_clk * m);
-	} else {
-bypass:
-		/* Bypass system PLL */
-		vco = 0;
-	}
-
-	/* CPU = VCO / ( FWDVA x CPUDV0) */
-	cpu = vco / (fwdva * cpudv0);
-	/* PLB = VCO / ( FWDVA x PLB2XDV0 x PLBDV0) */
-	plb = vco / (fwdva * plb2xdv0 * plbdv0);
-	/* OPB = PLB / OPBDV0 */
-	opb = plb / opbdv0;
-	/* EBC = OPB / PERDV0 */
-	ebc = opb / perdv0;
-
-	tb = cpu;
-	uart0 = uart1 = uart_clk;
-
-	dt_fixup_cpu_clocks(cpu, tb, 0);
-	dt_fixup_clock("/plb", plb);
-	dt_fixup_clock("/plb/opb", opb);
-	dt_fixup_clock("/plb/opb/ebc", ebc);
-	dt_fixup_clock("/plb/opb/serial@ef600200", uart0);
-	dt_fixup_clock("/plb/opb/serial@ef600300", uart1);
-}
diff --git a/arch/powerpc/boot/4xx.h b/arch/powerpc/boot/4xx.h
index 77f15d124c81..62df496b7ba6 100644
--- a/arch/powerpc/boot/4xx.h
+++ b/arch/powerpc/boot/4xx.h
@@ -12,13 +12,9 @@ void ibm4xx_sdram_fixup_memsize(void);
 void ibm440spe_fixup_memsize(void);
 void ibm4xx_denali_fixup_memsize(void);
 void ibm44x_dbcr_reset(void);
-void ibm40x_dbcr_reset(void);
 void ibm4xx_quiesce_eth(u32 *emac0, u32 *emac1);
 void ibm4xx_fixup_ebc_ranges(const char *ebc);
 
-void ibm405gp_fixup_clocks(unsigned int sys_clk, unsigned int ser_clk);
-void ibm405ep_fixup_clocks(unsigned int sys_clk);
-void ibm405ex_fixup_clocks(unsigned int sys_clk, unsigned int uart_clk);
 void ibm440gp_fixup_clocks(unsigned int sys_clk, unsigned int ser_clk);
 void ibm440ep_fixup_clocks(unsigned int sys_clk, unsigned int ser_clk,
 			   unsigned int tmr_clk);
diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile
index 968aee2025b8..b16892d11e0f 100644
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -54,10 +54,8 @@ endif
 
 $(obj)/4xx.o: BOOTTARGETFLAGS += -mcpu=405
 $(obj)/ebony.o: BOOTTARGETFLAGS += -mcpu=440
-$(obj)/cuboot-hotfoot.o: BOOTTARGETFLAGS += -mcpu=405
 $(obj)/cuboot-taishan.o: BOOTTARGETFLAGS += -mcpu=440
 $(obj)/cuboot-katmai.o: BOOTTARGETFLAGS += -mcpu=440
-$(obj)/cuboot-acadia.o: BOOTTARGETFLAGS += -mcpu=405
 $(obj)/treeboot-iss4xx.o: BOOTTARGETFLAGS += -mcpu=405
 $(obj)/treeboot-currituck.o: BOOTTARGETFLAGS += -mcpu=405
 $(obj)/treeboot-akebono.o: BOOTTARGETFLAGS += -mcpu=405
@@ -146,7 +144,6 @@ src-wlib-$(CONFIG_PPC_POWERNV) += opal-calls.S opal.c
 ifndef CONFIG_PPC64_BOOT_WRAPPER
 src-wlib-y += crtsavres.S
 endif
-src-wlib-$(CONFIG_40x) += 4xx.c planetcore.c
 src-wlib-$(CONFIG_44x) += 4xx.c ebony.c bamboo.c
 src-wlib-$(CONFIG_PPC_8xx) += mpc8xx.c planetcore.c fsl-soc.c
 src-wlib-$(CONFIG_PPC_82xx) += pq2.c fsl-soc.c planetcore.c
@@ -154,9 +151,6 @@ src-wlib-$(CONFIG_EMBEDDED6xx) += ugecon.c fsl-soc.c
 src-wlib-$(CONFIG_CPM) += cpm-serial.c
 
 src-plat-y := of.c epapr.c
-src-plat-$(CONFIG_40x) += fixed-head.S cuboot-hotfoot.c \
-				cuboot-acadia.c \
-				cuboot-kilauea.c simpleboot.c
 src-plat-$(CONFIG_44x) += treeboot-ebony.c cuboot-ebony.c treeboot-bamboo.c \
 				cuboot-bamboo.c cuboot-sam440ep.c \
 				cuboot-sequoia.c cuboot-rainier.c \
@@ -300,11 +294,6 @@ image-$(CONFIG_EPAPR_BOOT)		+= zImage.epapr
 # Boards with newish u-boot firmware can use the uImage target above
 #
 
-# Board ports in arch/powerpc/platform/40x/Kconfig
-image-$(CONFIG_HOTFOOT)			+= cuImage.hotfoot
-image-$(CONFIG_ACADIA)			+= cuImage.acadia
-image-$(CONFIG_OBS600)			+= uImage.obs600
-
 # Board ports in arch/powerpc/platform/44x/Kconfig
 image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
 image-$(CONFIG_BAMBOO)			+= treeImage.bamboo cuImage.bamboo
diff --git a/arch/powerpc/boot/cuboot-acadia.c b/arch/powerpc/boot/cuboot-acadia.c
deleted file mode 100644
index 46e96756cfe1..000000000000
--- a/arch/powerpc/boot/cuboot-acadia.c
+++ /dev/null
@@ -1,171 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Old U-boot compatibility for Acadia
- *
- * Author: Josh Boyer <jwboyer@linux.vnet.ibm.com>
- *
- * Copyright 2008 IBM Corporation
- */
-
-#include "ops.h"
-#include "io.h"
-#include "dcr.h"
-#include "stdio.h"
-#include "4xx.h"
-#include "44x.h"
-#include "cuboot.h"
-
-#define TARGET_4xx
-#include "ppcboot.h"
-
-static bd_t bd;
-
-#define CPR_PERD0_SPIDV_MASK   0x000F0000     /* SPI Clock Divider */
-
-#define PLLC_SRC_MASK	       0x20000000     /* PLL feedback source */
-
-#define PLLD_FBDV_MASK	       0x1F000000     /* PLL feedback divider value */
-#define PLLD_FWDVA_MASK        0x000F0000     /* PLL forward divider A value */
-#define PLLD_FWDVB_MASK        0x00000700     /* PLL forward divider B value */
-
-#define PRIMAD_CPUDV_MASK      0x0F000000     /* CPU Clock Divisor Mask */
-#define PRIMAD_PLBDV_MASK      0x000F0000     /* PLB Clock Divisor Mask */
-#define PRIMAD_OPBDV_MASK      0x00000F00     /* OPB Clock Divisor Mask */
-#define PRIMAD_EBCDV_MASK      0x0000000F     /* EBC Clock Divisor Mask */
-
-#define PERD0_PWMDV_MASK       0xFF000000     /* PWM Divider Mask */
-#define PERD0_SPIDV_MASK       0x000F0000     /* SPI Divider Mask */
-#define PERD0_U0DV_MASK        0x0000FF00     /* UART 0 Divider Mask */
-#define PERD0_U1DV_MASK        0x000000FF     /* UART 1 Divider Mask */
-
-static void get_clocks(void)
-{
-	unsigned long sysclk, cpr_plld, cpr_pllc, cpr_primad, plloutb, i;
-	unsigned long pllFwdDiv, pllFwdDivB, pllFbkDiv, pllPlbDiv, pllExtBusDiv;
-	unsigned long pllOpbDiv, freqEBC, freqUART, freqOPB;
-	unsigned long div;		/* total divisor udiv * bdiv */
-	unsigned long umin;		/* minimum udiv	*/
-	unsigned short diff;		/* smallest diff */
-	unsigned long udiv;		/* best udiv */
-	unsigned short idiff;		/* current diff */
-	unsigned short ibdiv;		/* current bdiv */
-	unsigned long est;		/* current estimate */
-	unsigned long baud;
-	void *np;
-
-	/* read the sysclk value from the CPLD */
-	sysclk = (in_8((unsigned char *)0x80000000) == 0xc) ? 66666666 : 33333000;
-
-	/*
-	 * Read PLL Mode registers
-	 */
-	cpr_plld = CPR0_READ(DCRN_CPR0_PLLD);
-	cpr_pllc = CPR0_READ(DCRN_CPR0_PLLC);
-
-	/*
-	 * Determine forward divider A
-	 */
-	pllFwdDiv = ((cpr_plld & PLLD_FWDVA_MASK) >> 16);
-
-	/*
-	 * Determine forward divider B
-	 */
-	pllFwdDivB = ((cpr_plld & PLLD_FWDVB_MASK) >> 8);
-	if (pllFwdDivB == 0)
-		pllFwdDivB = 8;
-
-	/*
-	 * Determine FBK_DIV.
-	 */
-	pllFbkDiv = ((cpr_plld & PLLD_FBDV_MASK) >> 24);
-	if (pllFbkDiv == 0)
-		pllFbkDiv = 256;
-
-	/*
-	 * Read CPR_PRIMAD register
-	 */
-	cpr_primad = CPR0_READ(DCRN_CPR0_PRIMAD);
-
-	/*
-	 * Determine PLB_DIV.
-	 */
-	pllPlbDiv = ((cpr_primad & PRIMAD_PLBDV_MASK) >> 16);
-	if (pllPlbDiv == 0)
-		pllPlbDiv = 16;
-
-	/*
-	 * Determine EXTBUS_DIV.
-	 */
-	pllExtBusDiv = (cpr_primad & PRIMAD_EBCDV_MASK);
-	if (pllExtBusDiv == 0)
-		pllExtBusDiv = 16;
-
-	/*
-	 * Determine OPB_DIV.
-	 */
-	pllOpbDiv = ((cpr_primad & PRIMAD_OPBDV_MASK) >> 8);
-	if (pllOpbDiv == 0)
-		pllOpbDiv = 16;
-
-	/* There is a bug in U-Boot that prevents us from using
-	 * bd.bi_opbfreq because U-Boot doesn't populate it for
-	 * 405EZ.  We get to calculate it, yay!
-	 */
-	freqOPB = (sysclk *pllFbkDiv) /pllOpbDiv;
-
-	freqEBC = (sysclk * pllFbkDiv) / pllExtBusDiv;
-
-	plloutb = ((sysclk * ((cpr_pllc & PLLC_SRC_MASK) ?
-					   pllFwdDivB : pllFwdDiv) *
-		    pllFbkDiv) / pllFwdDivB);
-
-	np = find_node_by_alias("serial0");
-	if (getprop(np, "current-speed", &baud, sizeof(baud)) != sizeof(baud))
-		fatal("no current-speed property\n\r");
-
-	udiv = 256;			/* Assume lowest possible serial clk */
-	div = plloutb / (16 * baud); /* total divisor */
-	umin = (plloutb / freqOPB) << 1;	/* 2 x OPB divisor */
-	diff = 256;			/* highest possible */
-
-	/* i is the test udiv value -- start with the largest
-	 * possible (256) to minimize serial clock and constrain
-	 * search to umin.
-	 */
-	for (i = 256; i > umin; i--) {
-		ibdiv = div / i;
-		est = i * ibdiv;
-		idiff = (est > div) ? (est-div) : (div-est);
-		if (idiff == 0) {
-			udiv = i;
-			break;      /* can't do better */
-		} else if (idiff < diff) {
-			udiv = i;       /* best so far */
-			diff = idiff;   /* update lowest diff*/
-		}
-	}
-	freqUART = plloutb / udiv;
-
-	dt_fixup_cpu_clocks(bd.bi_procfreq, bd.bi_intfreq, bd.bi_plb_busfreq);
-	dt_fixup_clock("/plb/ebc", freqEBC);
-	dt_fixup_clock("/plb/opb", freqOPB);
-	dt_fixup_clock("/plb/opb/serial@ef600300", freqUART);
-	dt_fixup_clock("/plb/opb/serial@ef600400", freqUART);
-}
-
-static void acadia_fixups(void)
-{
-	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
-	get_clocks();
-	dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
-}
-	
-void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
-		unsigned long r6, unsigned long r7)
-{
-	CUBOOT_INIT();
-	platform_ops.fixups = acadia_fixups;
-	platform_ops.exit = ibm40x_dbcr_reset;
-	fdt_init(_dtb_start);
-	serial_console_init();
-}
diff --git a/arch/powerpc/boot/cuboot-hotfoot.c b/arch/powerpc/boot/cuboot-hotfoot.c
deleted file mode 100644
index 0e5532f855d6..000000000000
--- a/arch/powerpc/boot/cuboot-hotfoot.c
+++ /dev/null
@@ -1,139 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Old U-boot compatibility for Esteem 195E Hotfoot CPU Board
- *
- * Author: Solomon Peachy <solomon@linux-wlan.com>
- */
-
-#include "ops.h"
-#include "stdio.h"
-#include "reg.h"
-#include "dcr.h"
-#include "4xx.h"
-#include "cuboot.h"
-
-#define TARGET_4xx
-#define TARGET_HOTFOOT
-
-#include "ppcboot-hotfoot.h"
-
-static bd_t bd;
-
-#define NUM_REGS 3
-
-static void hotfoot_fixups(void)
-{
-	u32 uart = mfdcr(DCRN_CPC0_UCR) & 0x7f;
-
-	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize); 
-
-	dt_fixup_cpu_clocks(bd.bi_procfreq, bd.bi_procfreq, 0);
-	dt_fixup_clock("/plb", bd.bi_plb_busfreq);
-	dt_fixup_clock("/plb/opb", bd.bi_opbfreq);
-	dt_fixup_clock("/plb/ebc", bd.bi_pci_busfreq);
-	dt_fixup_clock("/plb/opb/serial@ef600300", bd.bi_procfreq / uart); 
-	dt_fixup_clock("/plb/opb/serial@ef600400", bd.bi_procfreq / uart); 
-	
-	dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
-	dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
-
-	/* Is this a single eth/serial board? */
-	if ((bd.bi_enet1addr[0] == 0) && 
-	    (bd.bi_enet1addr[1] == 0) &&
-	    (bd.bi_enet1addr[2] == 0) &&
-	    (bd.bi_enet1addr[3] == 0) &&
-	    (bd.bi_enet1addr[4] == 0) &&
-	    (bd.bi_enet1addr[5] == 0)) {
-		void *devp;
-
-		printf("Trimming devtree for single serial/eth board\n");
-
-		devp = finddevice("/plb/opb/serial@ef600300");
-		if (!devp)
-			fatal("Can't find node for /plb/opb/serial@ef600300");
-		del_node(devp);
-
-		devp = finddevice("/plb/opb/ethernet@ef600900");
-		if (!devp)
-			fatal("Can't find node for /plb/opb/ethernet@ef600900");
-		del_node(devp);
-	}
-
-	ibm4xx_quiesce_eth((u32 *)0xef600800, (u32 *)0xef600900);
-
-	/* Fix up flash size in fdt for 4M boards. */
-	if (bd.bi_flashsize < 0x800000) {
-		u32 regs[NUM_REGS];
-		void *devp = finddevice("/plb/ebc/nor_flash@0");
-		if (!devp)
-			fatal("Can't find FDT node for nor_flash!??");
-
-		printf("Fixing devtree for 4M Flash\n");
-		
-		/* First fix up the base address */
-		getprop(devp, "reg", regs, sizeof(regs));
-		regs[0] = 0;
-		regs[1] = 0xffc00000;
-		regs[2] = 0x00400000;
-		setprop(devp, "reg", regs, sizeof(regs));
-		
-		/* Then the offsets */
-		devp = finddevice("/plb/ebc/nor_flash@0/partition@0");
-		if (!devp)
-			fatal("Can't find FDT node for partition@0");
-		getprop(devp, "reg", regs, 2*sizeof(u32));
-		regs[0] -= 0x400000;
-		setprop(devp, "reg", regs,  2*sizeof(u32));
-
-		devp = finddevice("/plb/ebc/nor_flash@0/partition@1");
-		if (!devp)
-			fatal("Can't find FDT node for partition@1");
-		getprop(devp, "reg", regs, 2*sizeof(u32));
-		regs[0] -= 0x400000;
-		setprop(devp, "reg", regs,  2*sizeof(u32));
-
-		devp = finddevice("/plb/ebc/nor_flash@0/partition@2");
-		if (!devp)
-			fatal("Can't find FDT node for partition@2");
-		getprop(devp, "reg", regs, 2*sizeof(u32));
-		regs[0] -= 0x400000;
-		setprop(devp, "reg", regs,  2*sizeof(u32));
-
-		devp = finddevice("/plb/ebc/nor_flash@0/partition@3");
-		if (!devp)
-			fatal("Can't find FDT node for partition@3");
-		getprop(devp, "reg", regs, 2*sizeof(u32));
-		regs[0] -= 0x400000;
-		setprop(devp, "reg", regs,  2*sizeof(u32));
-
-		devp = finddevice("/plb/ebc/nor_flash@0/partition@4");
-		if (!devp)
-			fatal("Can't find FDT node for partition@4");
-		getprop(devp, "reg", regs, 2*sizeof(u32));
-		regs[0] -= 0x400000;
-		setprop(devp, "reg", regs,  2*sizeof(u32));
-
-		devp = finddevice("/plb/ebc/nor_flash@0/partition@6");
-		if (!devp)
-			fatal("Can't find FDT node for partition@6");
-		getprop(devp, "reg", regs, 2*sizeof(u32));
-		regs[0] -= 0x400000;
-		setprop(devp, "reg", regs,  2*sizeof(u32));
-
-		/* Delete the FeatFS node */
-		devp = finddevice("/plb/ebc/nor_flash@0/partition@5");
-		if (!devp)
-			fatal("Can't find FDT node for partition@5");
-		del_node(devp);
-	}
-}
-
-void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
-		   unsigned long r6, unsigned long r7)
-{
-	CUBOOT_INIT();
-	platform_ops.fixups = hotfoot_fixups;
-        platform_ops.exit = ibm40x_dbcr_reset;
-	fdt_init(_dtb_start);
-	serial_console_init();
-}
diff --git a/arch/powerpc/boot/cuboot-kilauea.c b/arch/powerpc/boot/cuboot-kilauea.c
deleted file mode 100644
index fda182f518a2..000000000000
--- a/arch/powerpc/boot/cuboot-kilauea.c
+++ /dev/null
@@ -1,46 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Old U-boot compatibility for PPC405EX. This image is already included
- * a dtb.
- *
- * Author: Tiejun Chen <tiejun.chen@windriver.com>
- *
- * Copyright (C) 2009 Wind River Systems, Inc.
- */
-
-#include "ops.h"
-#include "io.h"
-#include "dcr.h"
-#include "stdio.h"
-#include "4xx.h"
-#include "44x.h"
-#include "cuboot.h"
-
-#define TARGET_4xx
-#define TARGET_44x
-#include "ppcboot.h"
-
-#define KILAUEA_SYS_EXT_SERIAL_CLOCK     11059200        /* ext. 11.059MHz clk */
-
-static bd_t bd;
-
-static void kilauea_fixups(void)
-{
-	unsigned long sysclk = 33333333;
-
-	ibm405ex_fixup_clocks(sysclk, KILAUEA_SYS_EXT_SERIAL_CLOCK);
-	dt_fixup_memory(bd.bi_memstart, bd.bi_memsize);
-	ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
-	dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
-	dt_fixup_mac_address_by_alias("ethernet1", bd.bi_enet1addr);
-}
-
-void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
-		unsigned long r6, unsigned long r7)
-{
-	CUBOOT_INIT();
-	platform_ops.fixups = kilauea_fixups;
-	platform_ops.exit = ibm40x_dbcr_reset;
-	fdt_init(_dtb_start);
-	serial_console_init();
-}
diff --git a/arch/powerpc/boot/dcr.h b/arch/powerpc/boot/dcr.h
index 334ab8b5a668..91dc3a302cc8 100644
--- a/arch/powerpc/boot/dcr.h
+++ b/arch/powerpc/boot/dcr.h
@@ -153,17 +153,6 @@ static const unsigned long sdram_bxcr[] = { SDRAM0_B0CR, SDRAM0_B1CR,
 #define CPR0_SCPID	0x120
 #define CPR0_PLLC0	0x40
 
-/* 405GP Clocking/Power Management/Chip Control regs */
-#define DCRN_CPC0_PLLMR 0xb0
-#define DCRN_405_CPC0_CR0 0xb1
-#define DCRN_405_CPC0_CR1 0xb2
-#define DCRN_405_CPC0_PSR 0xb4
-
-/* 405EP Clocking/Power Management/Chip Control regs */
-#define DCRN_CPC0_PLLMR0  0xf0
-#define DCRN_CPC0_PLLMR1  0xf4
-#define DCRN_CPC0_UCR     0xf5
-
 /* 440GX/405EX Clock Control reg */
 #define DCRN_CPR0_CLKUPD				0x020
 #define DCRN_CPR0_PLLC					0x040
diff --git a/arch/powerpc/boot/dts/acadia.dts b/arch/powerpc/boot/dts/acadia.dts
deleted file mode 100644
index deb52e41ab84..000000000000
--- a/arch/powerpc/boot/dts/acadia.dts
+++ /dev/null
@@ -1,224 +0,0 @@
-/*
- * Device Tree Source for AMCC Acadia (405EZ)
- *
- * Copyright IBM Corp. 2008
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/dts-v1/;
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "amcc,acadia";
-	compatible = "amcc,acadia";
-	dcr-parent = <&{/cpus/cpu@0}>;
-
-	aliases {
-		ethernet0 = &EMAC0;
-		serial0 = &UART0;
-		serial1 = &UART1;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			model = "PowerPC,405EZ";
-			reg = <0x0>;
-			clock-frequency = <0>; /* Filled in by wrapper */
-			timebase-frequency = <0>; /* Filled in by wrapper */
-			i-cache-line-size = <32>;
-			d-cache-line-size = <32>;
-			i-cache-size = <16384>;
-			d-cache-size = <16384>;
-			dcr-controller;
-			dcr-access-method = "native";
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x0>; /* Filled in by wrapper */
-	};
-
-	UIC0: interrupt-controller {
-		compatible = "ibm,uic-405ez", "ibm,uic";
-		interrupt-controller;
-		dcr-reg = <0x0c0 0x009>;
-		cell-index = <0>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-	};
-
-	plb {
-		compatible = "ibm,plb-405ez", "ibm,plb3";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		clock-frequency = <0>; /* Filled in by wrapper */
-
-		MAL0: mcmal {
-			compatible = "ibm,mcmal-405ez", "ibm,mcmal";
-			dcr-reg = <0x380 0x62>;
-			num-tx-chans = <1>;
-			num-rx-chans = <1>;
-			interrupt-parent = <&UIC0>;
-			/* 405EZ has only 3 interrupts to the UIC, as
-			 * SERR, TXDE, and RXDE are or'd together into
-			 * one UIC bit
-			 */
-			interrupts = <
-				0x13 0x4 /* TXEOB */
-				0x15 0x4 /* RXEOB */
-				0x12 0x4 /* SERR, TXDE, RXDE */>;
-		};
-
-		POB0: opb {
-			compatible = "ibm,opb-405ez", "ibm,opb";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			dcr-reg = <0x0a 0x05>;
-			clock-frequency = <0>; /* Filled in by wrapper */
-
-			UART0: serial@ef600300 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600300 0x8>;
-				virtual-reg = <0xef600300>;
-				clock-frequency = <0>; /* Filled in by wrapper */
-				current-speed = <115200>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x5 0x4>;
-			};
-
-			UART1: serial@ef600400 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600400 0x8>;
-				clock-frequency = <0>; /* Filled in by wrapper */
-				current-speed = <115200>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x6 0x4>;
-			};
-
-			IIC: i2c@ef600500 {
-				compatible = "ibm,iic-405ez", "ibm,iic";
-				reg = <0xef600500 0x11>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0xa 0x4>;
-			};
-
-			GPIO0: gpio@ef600700 {
-				compatible = "ibm,gpio-405ez";
-				reg = <0xef600700 0x20>;
-			};
-
-			GPIO1: gpio@ef600800 {
-				compatible = "ibm,gpio-405ez";
-				reg = <0xef600800 0x20>;
-			};
-
-			EMAC0: ethernet@ef600900 {
-				device_type = "network";
-				compatible = "ibm,emac-405ez", "ibm,emac";
-				interrupt-parent = <&UIC0>;
-				interrupts = <
-					0x10 0x4 /* Ethernet */
-					0x11 0x4 /* Ethernet Wake up */>;
-				local-mac-address = [000000000000]; /* Filled in by wrapper */
-				reg = <0xef600900 0x70>;
-				mal-device = <&MAL0>;
-				mal-tx-channel = <0>;
-				mal-rx-channel = <0>;
-				cell-index = <0>;
-				max-frame-size = <1500>;
-				rx-fifo-size = <4096>;
-				tx-fifo-size = <2048>;
-				phy-mode = "mii";
-				phy-map = <0x0>;
-			};
-
-			CAN0: can@ef601000 {
-				compatible = "amcc,can-405ez";
-				reg = <0xef601000 0x620>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x7 0x4>;
-			};
-
-			CAN1: can@ef601800 {
-				compatible = "amcc,can-405ez";
-				reg = <0xef601800 0x620>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x8 0x4>;
-			};
-
-			cameleon@ef602000 {
-				compatible = "amcc,cameleon-405ez";
-				reg = <0xef602000 0x800>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0xb 0x4 0xc 0x4>;
-			};
-
-			ieee1588@ef602800 {
-				compatible = "amcc,ieee1588-405ez";
-				reg = <0xef602800 0x60>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x4 0x4>;
-				/* This thing is a bit weird.  It has it's own UIC
-				 * that it uses to generate snapshot triggers.  We
-				 * don't really support this device yet, and it needs
-				 * work to figure this out.
-				 */
-				dcr-reg = <0xe0 0x9>;
-			};
-
-			usb@ef603000 {
-				compatible = "ohci-be";
-				reg = <0xef603000 0x80>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0xd 0x4 0xe 0x4>;
-			};
-
-			dac@ef603300 {
-				compatible = "amcc,dac-405ez";
-				reg = <0xef603300 0x40>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x18 0x4>;
-			};
-
-			adc@ef603400 {
-				compatible = "amcc,adc-405ez";
-				reg = <0xef603400 0x40>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x17 0x4>;
-			};
-
-			spi@ef603500 {
-				compatible = "amcc,spi-405ez";
-				reg = <0xef603500 0x100>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x9 0x4>;
-			};
-		};
-
-		EBC0: ebc {
-			compatible = "ibm,ebc-405ez", "ibm,ebc";
-			dcr-reg = <0x12 0x2>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-			clock-frequency = <0>; /* Filled in by wrapper */
-		};
-	};
-
-	chosen {
-		stdout-path = "/plb/opb/serial@ef600300";
-	};
-};
diff --git a/arch/powerpc/boot/dts/hotfoot.dts b/arch/powerpc/boot/dts/hotfoot.dts
deleted file mode 100644
index b93bf2d9dd5b..000000000000
--- a/arch/powerpc/boot/dts/hotfoot.dts
+++ /dev/null
@@ -1,296 +0,0 @@
-/*
- * Device Tree Source for ESTeem 195E Hotfoot
- *
- * Copyright 2009 AbsoluteValue Systems <solomon@linux-wlan.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without
- * any warranty of any kind, whether express or implied.
- */
-
-/dts-v1/;
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "est,hotfoot";
-	compatible = "est,hotfoot";
-	dcr-parent = <&{/cpus/cpu@0}>;
-
-	aliases {
-		ethernet0 = &EMAC0;
-		ethernet1 = &EMAC1;
-		serial0 = &UART0;
-		serial1 = &UART1;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			model = "PowerPC,405EP";
-			reg = <0x00000000>;
-			clock-frequency = <0>; /* Filled in by zImage */
-			timebase-frequency = <0>; /* Filled in by zImage */
-			i-cache-line-size = <0x20>;
-			d-cache-line-size = <0x20>;
-			i-cache-size = <0x4000>;
-			d-cache-size = <0x4000>;
-			dcr-controller;
-			dcr-access-method = "native";
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x00000000>; /* Filled in by zImage */
-	};
-
-	UIC0: interrupt-controller {
-		compatible = "ibm,uic";
-		interrupt-controller;
-		cell-index = <0>;
-		dcr-reg = <0x0c0 0x009>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-	};
-
-	plb {
-		compatible = "ibm,plb3";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		clock-frequency = <0>; /* Filled in by zImage */
-
-		SDRAM0: memory-controller {
-			compatible = "ibm,sdram-405ep";
-			dcr-reg = <0x010 0x002>;
-		};
-
-		MAL: mcmal {
-			compatible = "ibm,mcmal-405ep", "ibm,mcmal";
-			dcr-reg = <0x180 0x062>;
-			num-tx-chans = <4>;
-			num-rx-chans = <2>;
-			interrupt-parent = <&UIC0>;
-			interrupts = <
-				0xb 0x4 /* TXEOB */
-				0xc 0x4 /* RXEOB */
-				0xa 0x4 /* SERR */
-				0xd 0x4 /* TXDE */
-				0xe 0x4 /* RXDE */>;
-		};
-
-		POB0: opb {
-			compatible = "ibm,opb-405ep", "ibm,opb";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0xef600000 0xef600000 0x00a00000>;
-			dcr-reg = <0x0a0 0x005>;
-			clock-frequency = <0>; /* Filled in by zImage */
-
-			/* Hotfoot has UART0/UART1 swapped */
-
-			UART0: serial@ef600400 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600400 0x00000008>;
-				virtual-reg = <0xef600400>;
-				clock-frequency = <0>; /* Filled in by zImage */
-				current-speed = <0x9600>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x1 0x4>;
-			};
-
-			UART1: serial@ef600300 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600300 0x00000008>;
-				virtual-reg = <0xef600300>;
-				clock-frequency = <0>; /* Filled in by zImage */
-				current-speed = <0x9600>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x0 0x4>;
-			};
-
-			IIC: i2c@ef600500 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "ibm,iic-405ep", "ibm,iic";
-				reg = <0xef600500 0x00000011>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x2 0x4>;
-
-				rtc@68 {
-					/* Actually a DS1339 */
-					compatible = "dallas,ds1307";
-					reg = <0x68>;
-				};
-
-				temp@4a {
-					/* Not present on all boards */
-					compatible = "national,lm75";
-					reg = <0x4a>;
-				};
-			};
-
-			GPIO: gpio@ef600700 {
-				#gpio-cells = <2>;
-				compatible = "ibm,ppc4xx-gpio";
-				reg = <0xef600700 0x00000020>;
-				gpio-controller;
-			};
-
-			gpio-leds {
-				compatible = "gpio-leds";
-				status {
-					label = "Status";
-					gpios = <&GPIO 1 0>;
-				};
-				radiorx {
-					label = "Rx";
-					gpios = <&GPIO 0xe 0>;
-				};
-			};
-
-			EMAC0: ethernet@ef600800 {
-				linux,network-index = <0x0>;
-				device_type = "network";
-				compatible = "ibm,emac-405ep", "ibm,emac";
-				interrupt-parent = <&UIC0>;
-				interrupts = <
-					0xf 0x4 /* Ethernet */
-					0x9 0x4 /* Ethernet Wake Up */>;
-				local-mac-address = [000000000000]; /* Filled in by zImage */
-				reg = <0xef600800 0x00000070>;
-				mal-device = <&MAL>;
-				mal-tx-channel = <0>;
-				mal-rx-channel = <0>;
-				cell-index = <0>;
-				max-frame-size = <0x5dc>;
-				rx-fifo-size = <0x1000>;
-				tx-fifo-size = <0x800>;
-				phy-mode = "mii";
-				phy-map = <0x00000000>;
-			};
-
-			EMAC1: ethernet@ef600900 {
-				linux,network-index = <0x1>;
-				device_type = "network";
-				compatible = "ibm,emac-405ep", "ibm,emac";
-				interrupt-parent = <&UIC0>;
-				interrupts = <
-					0x11 0x4 /* Ethernet */
-					0x9 0x4 /* Ethernet Wake Up */>;
-				local-mac-address = [000000000000]; /* Filled in by zImage */
-				reg = <0xef600900 0x00000070>;
-				mal-device = <&MAL>;
-				mal-tx-channel = <2>;
-				mal-rx-channel = <1>;
-				cell-index = <1>;
-				max-frame-size = <0x5dc>;
-				rx-fifo-size = <0x1000>;
-				tx-fifo-size = <0x800>;
-				mdio-device = <&EMAC0>;
-				phy-mode = "mii";
-				phy-map = <0x0000001>;
-			};
-		};
-
-		EBC0: ebc {
-			compatible = "ibm,ebc-405ep", "ibm,ebc";
-			dcr-reg = <0x012 0x002>;
-			#address-cells = <2>;
-			#size-cells = <1>;
-
-			/* The ranges property is supplied by the bootwrapper
-			 * and is based on the firmware's configuration of the
-			 * EBC bridge
-			 */
-			clock-frequency = <0>; /* Filled in by zImage */
-
-			nor_flash@0 {
-				compatible = "cfi-flash";
-				bank-width = <2>;
-				reg = <0x0 0xff800000 0x00800000>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-
-				/* This mapping is for the 8M flash
-				   4M flash has all ofssets -= 4M,
-				   and FeatFS partition is not present */
-				partition@0 {
-					label = "Bootloader";
-					reg = <0x7c0000 0x40000>;
-					/* read-only; */
-				};
-				partition@1 {
-					label = "Env_and_Config_Primary";
-					reg = <0x400000 0x10000>;
-				};
-				partition@2 {
-					label = "Kernel";
-					reg = <0x420000 0x100000>;
-				};
-				partition@3 {
-					label = "Filesystem";
-					reg = <0x520000 0x2a0000>;
-				};
-				partition@4 {
-					label = "Env_and_Config_Secondary";
-					reg = <0x410000 0x10000>;
-				};
-				partition@5 {
-					label = "FeatFS";
-					reg = <0x000000 0x400000>;
-				};
-				partition@6 {
-					label = "Bootloader_Env";
-					reg = <0x7d0000 0x10000>;
-				};
-			};
-		};
-
-		PCI0: pci@ec000000 {
-			device_type = "pci";
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			compatible = "ibm,plb405ep-pci", "ibm,plb-pci";
-			primary;
-			reg = <0xeec00000 0x00000008    /* Config space access */
-				0xeed80000 0x00000004    /* IACK */
-				0xeed80000 0x00000004    /* Special cycle */
-				0xef480000 0x00000040>;  /* Internal registers */
-
-			/* Outbound ranges, one memory and one IO,
-			 * later cannot be changed. Chip supports a second
-			 * IO range but we don't use it for now
-			 */
-			ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x20000000
-				0x01000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
-
-			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
-
-			interrupt-parent = <&UIC0>;
-			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
-			interrupt-map = <
-				/* IDSEL 3 -- slot1 (optional) 27/29 A/B IRQ2/4 */
-				0x1800 0x0 0x0 0x1 &UIC0 0x1b 0x8
-				0x1800 0x0 0x0 0x2 &UIC0 0x1d 0x8
-
-				/* IDSEL 4 -- slot0, 26/28 A/B IRQ1/3 */
-				0x2000 0x0 0x0 0x1 &UIC0 0x1a 0x8
-				0x2000 0x0 0x0 0x2 &UIC0 0x1c 0x8
-				>;
-		};
-	};
-
-	chosen {
-		stdout-path = &UART0;
-	};
-};
diff --git a/arch/powerpc/boot/dts/kilauea.dts b/arch/powerpc/boot/dts/kilauea.dts
deleted file mode 100644
index c07a7525a72c..000000000000
--- a/arch/powerpc/boot/dts/kilauea.dts
+++ /dev/null
@@ -1,407 +0,0 @@
-/*
- * Device Tree Source for AMCC Kilauea (405EX)
- *
- * Copyright 2007-2009 DENX Software Engineering, Stefan Roese <sr@denx.de>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without
- * any warranty of any kind, whether express or implied.
- */
-
-/dts-v1/;
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "amcc,kilauea";
-	compatible = "amcc,kilauea";
-	dcr-parent = <&{/cpus/cpu@0}>;
-
-	aliases {
-		ethernet0 = &EMAC0;
-		ethernet1 = &EMAC1;
-		serial0 = &UART0;
-		serial1 = &UART1;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			model = "PowerPC,405EX";
-			reg = <0x00000000>;
-			clock-frequency = <0>; /* Filled in by U-Boot */
-			timebase-frequency = <0>; /* Filled in by U-Boot */
-			i-cache-line-size = <32>;
-			d-cache-line-size = <32>;
-			i-cache-size = <16384>; /* 16 kB */
-			d-cache-size = <16384>; /* 16 kB */
-			dcr-controller;
-			dcr-access-method = "native";
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x00000000>; /* Filled in by U-Boot */
-	};
-
-	UIC0: interrupt-controller {
-		compatible = "ibm,uic-405ex", "ibm,uic";
-		interrupt-controller;
-		cell-index = <0>;
-		dcr-reg = <0x0c0 0x009>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-	};
-
-	UIC1: interrupt-controller1 {
-		compatible = "ibm,uic-405ex","ibm,uic";
-		interrupt-controller;
-		cell-index = <1>;
-		dcr-reg = <0x0d0 0x009>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-		interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */
-		interrupt-parent = <&UIC0>;
-	};
-
-	UIC2: interrupt-controller2 {
-		compatible = "ibm,uic-405ex","ibm,uic";
-		interrupt-controller;
-		cell-index = <2>;
-		dcr-reg = <0x0e0 0x009>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-		interrupts = <0x1c 0x4 0x1d 0x4>; /* cascade */
-		interrupt-parent = <&UIC0>;
-	};
-
-	CPM0: cpm {
-		compatible = "ibm,cpm";
-		dcr-access-method = "native";
-		dcr-reg = <0x0b0 0x003>;
-		unused-units = <0x00000000>;
-		idle-doze = <0x02000000>;
-		standby = <0xe3e74800>;
-	};
-
-	plb {
-		compatible = "ibm,plb-405ex", "ibm,plb4";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		clock-frequency = <0>; /* Filled in by U-Boot */
-
-		SDRAM0: memory-controller {
-			compatible = "ibm,sdram-405ex", "ibm,sdram-4xx-ddr2";
-			dcr-reg = <0x010 0x002>;
-			interrupt-parent = <&UIC2>;
-			interrupts = <0x5 0x4	/* ECC DED Error */ 
-				      0x6 0x4>;	/* ECC SEC Error */ 
-		};
-
-		CRYPTO: crypto@ef700000 {
-			compatible = "amcc,ppc405ex-crypto", "amcc,ppc4xx-crypto";
-			reg = <0xef700000 0x80400>;
-			interrupt-parent = <&UIC0>;
-			interrupts = <0x17 0x2>;
-		};
-
-		MAL0: mcmal {
-			compatible = "ibm,mcmal-405ex", "ibm,mcmal2";
-			dcr-reg = <0x180 0x062>;
-			num-tx-chans = <2>;
-			num-rx-chans = <2>;
-			interrupt-parent = <&MAL0>;
-			interrupts = <0x0 0x1 0x2 0x3 0x4>;
-			#interrupt-cells = <1>;
-			#address-cells = <0>;
-			#size-cells = <0>;
-			interrupt-map = </*TXEOB*/ 0x0 &UIC0 0xa 0x4
-					/*RXEOB*/ 0x1 &UIC0 0xb 0x4
-					/*SERR*/  0x2 &UIC1 0x0 0x4
-					/*TXDE*/  0x3 &UIC1 0x1 0x4
-					/*RXDE*/  0x4 &UIC1 0x2 0x4>;
-			interrupt-map-mask = <0xffffffff>;
-		};
-
-		POB0: opb {
-			compatible = "ibm,opb-405ex", "ibm,opb";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x80000000 0x80000000 0x10000000
-				  0xef600000 0xef600000 0x00a00000
-				  0xf0000000 0xf0000000 0x10000000>;
-			dcr-reg = <0x0a0 0x005>;
-			clock-frequency = <0>; /* Filled in by U-Boot */
-
-			EBC0: ebc {
-				compatible = "ibm,ebc-405ex", "ibm,ebc";
-				dcr-reg = <0x012 0x002>;
-				#address-cells = <2>;
-				#size-cells = <1>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				/* ranges property is supplied by U-Boot */
-				interrupts = <0x5 0x1>;
-				interrupt-parent = <&UIC1>;
-
-				nor_flash@0,0 {
-					compatible = "amd,s29gl512n", "cfi-flash";
-					bank-width = <2>;
-					reg = <0x00000000 0x00000000 0x04000000>;
-					#address-cells = <1>;
-					#size-cells = <1>;
-					partition@0 {
-						label = "kernel";
-						reg = <0x00000000 0x001e0000>;
-					};
-					partition@1e0000 {
-						label = "dtb";
-						reg = <0x001e0000 0x00020000>;
-					};
-					partition@200000 {
-						label = "root";
-						reg = <0x00200000 0x00200000>;
-					};
-					partition@400000 {
-						label = "user";
-						reg = <0x00400000 0x03b60000>;
-					};
-					partition@3f60000 {
-						label = "env";
-						reg = <0x03f60000 0x00040000>;
-					};
-					partition@3fa0000 {
-						label = "u-boot";
-						reg = <0x03fa0000 0x00060000>;
-					};
-				};
-
-				ndfc@1,0 {
-					compatible = "ibm,ndfc";
-					reg = <0x00000001 0x00000000 0x00002000>;
-					ccr = <0x00001000>;
-					bank-settings = <0x80002222>;
-					#address-cells = <1>;
-					#size-cells = <1>;
-
-					nand {
-						#address-cells = <1>;
-						#size-cells = <1>;
-
-						partition@0 {
-							label = "u-boot";
-							reg = <0x00000000 0x00100000>;
-						};
-						partition@100000 {
-							label = "user";
-							reg = <0x00000000 0x03f00000>;
-						};
-					};
-				};
-			};
-
-			UART0: serial@ef600200 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600200 0x00000008>;
-				virtual-reg = <0xef600200>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				current-speed = <0>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x1a 0x4>;
-			};
-
-			UART1: serial@ef600300 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600300 0x00000008>;
-				virtual-reg = <0xef600300>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				current-speed = <0>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x1 0x4>;
-			};
-
-			IIC0: i2c@ef600400 {
-				compatible = "ibm,iic-405ex", "ibm,iic";
-				reg = <0xef600400 0x00000014>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x2 0x4>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				rtc@68 {
-					compatible = "dallas,ds1338";
-					reg = <0x68>;
-				};
-
-				dtt@48 {
-					compatible = "dallas,ds1775";
-					reg = <0x48>;
-				};
-			};
-
-			IIC1: i2c@ef600500 {
-				compatible = "ibm,iic-405ex", "ibm,iic";
-				reg = <0xef600500 0x00000014>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x7 0x4>;
-			};
-
-			RGMII0: emac-rgmii@ef600b00 {
-				compatible = "ibm,rgmii-405ex", "ibm,rgmii";
-				reg = <0xef600b00 0x00000104>;
-				has-mdio;
-			};
-
-			EMAC0: ethernet@ef600900 {
-				linux,network-index = <0x0>;
-				device_type = "network";
-				compatible = "ibm,emac-405ex", "ibm,emac4sync";
-				interrupt-parent = <&EMAC0>;
-				interrupts = <0x0 0x1>;
-				#interrupt-cells = <1>;
-				#address-cells = <0>;
-				#size-cells = <0>;
-				interrupt-map = </*Status*/ 0x0 &UIC0 0x18 0x4
-						/*Wake*/  0x1 &UIC1 0x1d 0x4>;
-				reg = <0xef600900 0x000000c4>;
-				local-mac-address = [000000000000]; /* Filled in by U-Boot */
-				mal-device = <&MAL0>;
-				mal-tx-channel = <0>;
-				mal-rx-channel = <0>;
-				cell-index = <0>;
-				max-frame-size = <9000>;
-				rx-fifo-size = <4096>;
-				tx-fifo-size = <2048>;
-				rx-fifo-size-gige = <16384>;
-				tx-fifo-size-gige = <16384>;
-				phy-mode = "rgmii";
-				phy-map = <0x00000000>;
-				rgmii-device = <&RGMII0>;
-				rgmii-channel = <0>;
-				has-inverted-stacr-oc;
-				has-new-stacr-staopc;
-			};
-
-			EMAC1: ethernet@ef600a00 {
-				linux,network-index = <0x1>;
-				device_type = "network";
-				compatible = "ibm,emac-405ex", "ibm,emac4sync";
-				interrupt-parent = <&EMAC1>;
-				interrupts = <0x0 0x1>;
-				#interrupt-cells = <1>;
-				#address-cells = <0>;
-				#size-cells = <0>;
-				interrupt-map = </*Status*/ 0x0 &UIC0 0x19 0x4
-						/*Wake*/  0x1 &UIC1 0x1f 0x4>;
-				reg = <0xef600a00 0x000000c4>;
-				local-mac-address = [000000000000]; /* Filled in by U-Boot */
-				mal-device = <&MAL0>;
-				mal-tx-channel = <1>;
-				mal-rx-channel = <1>;
-				cell-index = <1>;
-				max-frame-size = <9000>;
-				rx-fifo-size = <4096>;
-				tx-fifo-size = <2048>;
-				rx-fifo-size-gige = <16384>;
-				tx-fifo-size-gige = <16384>;
-				phy-mode = "rgmii";
-				phy-map = <0x00000000>;
-				rgmii-device = <&RGMII0>;
-				rgmii-channel = <1>;
-				has-inverted-stacr-oc;
-				has-new-stacr-staopc;
-			};
-		};
-
-		PCIE0: pcie@a0000000 {
-			device_type = "pci";
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			compatible = "ibm,plb-pciex-405ex", "ibm,plb-pciex";
-			primary;
-			port = <0x0>; /* port number */
-			reg = <0xa0000000 0x20000000	/* Config space access */
-			       0xef000000 0x00001000>;	/* Registers */
-			dcr-reg = <0x040 0x020>;
-			sdr-base = <0x400>;
-
-			/* Outbound ranges, one memory and one IO,
-			 * later cannot be changed
-			 */
-			ranges = <0x02000000 0x00000000 0x80000000 0x90000000 0x00000000 0x08000000
-				  0x01000000 0x00000000 0x00000000 0xe0000000 0x00000000 0x00010000>;
-
-			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
-
-			/* This drives busses 0x00 to 0x3f */
-			bus-range = <0x0 0x3f>;
-
-			/* Legacy interrupts (note the weird polarity, the bridge seems
-			 * to invert PCIe legacy interrupts).
-			 * We are de-swizzling here because the numbers are actually for
-			 * port of the root complex virtual P2P bridge. But I want
-			 * to avoid putting a node for it in the tree, so the numbers
-			 * below are basically de-swizzled numbers.
-			 * The real slot is on idsel 0, so the swizzling is 1:1
-			 */
-			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <
-				0x0 0x0 0x0 0x1 &UIC2 0x0 0x4 /* swizzled int A */
-				0x0 0x0 0x0 0x2 &UIC2 0x1 0x4 /* swizzled int B */
-				0x0 0x0 0x0 0x3 &UIC2 0x2 0x4 /* swizzled int C */
-				0x0 0x0 0x0 0x4 &UIC2 0x3 0x4 /* swizzled int D */>;
-		};
-
-		PCIE1: pcie@c0000000 {
-			device_type = "pci";
-			#interrupt-cells = <1>;
-			#size-cells = <2>;
-			#address-cells = <3>;
-			compatible = "ibm,plb-pciex-405ex", "ibm,plb-pciex";
-			primary;
-			port = <0x1>; /* port number */
-			reg = <0xc0000000 0x20000000	/* Config space access */
-			       0xef001000 0x00001000>;	/* Registers */
-			dcr-reg = <0x060 0x020>;
-			sdr-base = <0x440>;
-
-			/* Outbound ranges, one memory and one IO,
-			 * later cannot be changed
-			 */
-			ranges = <0x02000000 0x00000000 0x80000000 0x98000000 0x00000000 0x08000000
-				  0x01000000 0x00000000 0x00000000 0xe0010000 0x00000000 0x00010000>;
-
-			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
-
-			/* This drives busses 0x40 to 0x7f */
-			bus-range = <0x40 0x7f>;
-
-			/* Legacy interrupts (note the weird polarity, the bridge seems
-			 * to invert PCIe legacy interrupts).
-			 * We are de-swizzling here because the numbers are actually for
-			 * port of the root complex virtual P2P bridge. But I want
-			 * to avoid putting a node for it in the tree, so the numbers
-			 * below are basically de-swizzled numbers.
-			 * The real slot is on idsel 0, so the swizzling is 1:1
-			 */
-			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-			interrupt-map = <
-				0x0 0x0 0x0 0x1 &UIC2 0xb 0x4 /* swizzled int A */
-				0x0 0x0 0x0 0x2 &UIC2 0xc 0x4 /* swizzled int B */
-				0x0 0x0 0x0 0x3 &UIC2 0xd 0x4 /* swizzled int C */
-				0x0 0x0 0x0 0x4 &UIC2 0xe 0x4 /* swizzled int D */>;
-		};
-	};
-};
diff --git a/arch/powerpc/boot/dts/obs600.dts b/arch/powerpc/boot/dts/obs600.dts
deleted file mode 100644
index d10b0411809b..000000000000
--- a/arch/powerpc/boot/dts/obs600.dts
+++ /dev/null
@@ -1,314 +0,0 @@
-/*
- * Device Tree Source for PlatHome OpenBlockS 600 (405EX)
- *
- * Copyright 2011 Ben Herrenschmidt, IBM Corp.
- *
- * Based on Kilauea by:
- *
- * Copyright 2007-2009 DENX Software Engineering, Stefan Roese <sr@denx.de>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without
- * any warranty of any kind, whether express or implied.
- */
-
-/dts-v1/;
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "PlatHome,OpenBlockS 600";
-	compatible = "plathome,obs600";
-	dcr-parent = <&{/cpus/cpu@0}>;
-
-	aliases {
-		ethernet0 = &EMAC0;
-		ethernet1 = &EMAC1;
-		serial0 = &UART0;
-		serial1 = &UART1;
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			model = "PowerPC,405EX";
-			reg = <0x00000000>;
-			clock-frequency = <0>; /* Filled in by U-Boot */
-			timebase-frequency = <0>; /* Filled in by U-Boot */
-			i-cache-line-size = <32>;
-			d-cache-line-size = <32>;
-			i-cache-size = <16384>; /* 16 kB */
-			d-cache-size = <16384>; /* 16 kB */
-			dcr-controller;
-			dcr-access-method = "native";
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x00000000>; /* Filled in by U-Boot */
-	};
-
-	UIC0: interrupt-controller {
-		compatible = "ibm,uic-405ex", "ibm,uic";
-		interrupt-controller;
-		cell-index = <0>;
-		dcr-reg = <0x0c0 0x009>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-	};
-
-	UIC1: interrupt-controller1 {
-		compatible = "ibm,uic-405ex","ibm,uic";
-		interrupt-controller;
-		cell-index = <1>;
-		dcr-reg = <0x0d0 0x009>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-		interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */
-		interrupt-parent = <&UIC0>;
-	};
-
-	UIC2: interrupt-controller2 {
-		compatible = "ibm,uic-405ex","ibm,uic";
-		interrupt-controller;
-		cell-index = <2>;
-		dcr-reg = <0x0e0 0x009>;
-		#address-cells = <0>;
-		#size-cells = <0>;
-		#interrupt-cells = <2>;
-		interrupts = <0x1c 0x4 0x1d 0x4>; /* cascade */
-		interrupt-parent = <&UIC0>;
-	};
-
-	CPM0: cpm {
-		compatible = "ibm,cpm";
-		dcr-access-method = "native";
-		dcr-reg = <0x0b0 0x003>;
-		unused-units = <0x00000000>;
-		idle-doze = <0x02000000>;
-		standby = <0xe3e74800>;
-	};
-
-	plb {
-		compatible = "ibm,plb-405ex", "ibm,plb4";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		clock-frequency = <0>; /* Filled in by U-Boot */
-
-		SDRAM0: memory-controller {
-			compatible = "ibm,sdram-405ex", "ibm,sdram-4xx-ddr2";
-			dcr-reg = <0x010 0x002>;
-			interrupt-parent = <&UIC2>;
-			interrupts = <0x5 0x4	/* ECC DED Error */
-				      0x6 0x4>;	/* ECC SEC Error */
-		};
-
-		CRYPTO: crypto@ef700000 {
-			compatible = "amcc,ppc405ex-crypto", "amcc,ppc4xx-crypto";
-			reg = <0xef700000 0x80400>;
-			interrupt-parent = <&UIC0>;
-			interrupts = <0x17 0x2>;
-		};
-
-		MAL0: mcmal {
-			compatible = "ibm,mcmal-405ex", "ibm,mcmal2";
-			dcr-reg = <0x180 0x062>;
-			num-tx-chans = <2>;
-			num-rx-chans = <2>;
-			interrupt-parent = <&MAL0>;
-			interrupts = <0x0 0x1 0x2 0x3 0x4>;
-			#interrupt-cells = <1>;
-			#address-cells = <0>;
-			#size-cells = <0>;
-			interrupt-map = </*TXEOB*/ 0x0 &UIC0 0xa 0x4
-					/*RXEOB*/ 0x1 &UIC0 0xb 0x4
-					/*SERR*/  0x2 &UIC1 0x0 0x4
-					/*TXDE*/  0x3 &UIC1 0x1 0x4
-					/*RXDE*/  0x4 &UIC1 0x2 0x4>;
-			interrupt-map-mask = <0xffffffff>;
-		};
-
-		POB0: opb {
-			compatible = "ibm,opb-405ex", "ibm,opb";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x80000000 0x80000000 0x10000000
-				  0xef600000 0xef600000 0x00a00000
-				  0xf0000000 0xf0000000 0x10000000>;
-			dcr-reg = <0x0a0 0x005>;
-			clock-frequency = <0>; /* Filled in by U-Boot */
-
-			EBC0: ebc {
-				compatible = "ibm,ebc-405ex", "ibm,ebc";
-				dcr-reg = <0x012 0x002>;
-				#address-cells = <2>;
-				#size-cells = <1>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				/* ranges property is supplied by U-Boot */
-				interrupts = <0x5 0x1>;
-				interrupt-parent = <&UIC1>;
-
-				nor_flash@0,0 {
-					compatible = "amd,s29gl512n", "cfi-flash";
-					bank-width = <2>;
-					reg = <0x00000000 0x00000000 0x08000000>;
-					#address-cells = <1>;
-					#size-cells = <1>;
-					partition@0 {
-						label = "kernel + initrd";
-						reg = <0x00000000 0x03de0000>;
-					};
-					partition@3de0000 {
-						label = "user config area";
-						reg = <0x03de0000 0x00080000>;
-					};
-					partition@3e60000 {
-						label = "user program area";
-						reg = <0x03e60000 0x04000000>;
-					};
-					partition@7e60000 {
-						label = "flat device tree";
-						reg = <0x07e60000 0x00080000>;
-					};
-					partition@7ee0000 {
-						label = "test program";
-						reg = <0x07ee0000 0x00080000>;
-					};
-					partition@7f60000 {
-						label = "u-boot env";
-						reg = <0x07f60000 0x00040000>;
-					};
-					partition@7fa0000 {
-						label = "u-boot";
-						reg = <0x07fa0000 0x00060000>;
-					};
-				};
-			};
-
-			UART0: serial@ef600200 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600200 0x00000008>;
-				virtual-reg = <0xef600200>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				current-speed = <0>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x1a 0x4>;
-			};
-
-			UART1: serial@ef600300 {
-				device_type = "serial";
-				compatible = "ns16550";
-				reg = <0xef600300 0x00000008>;
-				virtual-reg = <0xef600300>;
-				clock-frequency = <0>; /* Filled in by U-Boot */
-				current-speed = <0>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x1 0x4>;
-			};
-
-			IIC0: i2c@ef600400 {
-				compatible = "ibm,iic-405ex", "ibm,iic";
-				reg = <0xef600400 0x00000014>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x2 0x4>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				rtc@68 {
-					compatible = "dallas,ds1340";
-					reg = <0x68>;
-				};
-			};
-
-			IIC1: i2c@ef600500 {
-				compatible = "ibm,iic-405ex", "ibm,iic";
-				reg = <0xef600500 0x00000014>;
-				interrupt-parent = <&UIC0>;
-				interrupts = <0x7 0x4>;
-			};
-
-			RGMII0: emac-rgmii@ef600b00 {
-				compatible = "ibm,rgmii-405ex", "ibm,rgmii";
-				reg = <0xef600b00 0x00000104>;
-				has-mdio;
-			};
-
-			EMAC0: ethernet@ef600900 {
-				linux,network-index = <0x0>;
-				device_type = "network";
-				compatible = "ibm,emac-405ex", "ibm,emac4sync";
-				interrupt-parent = <&EMAC0>;
-				interrupts = <0x0 0x1>;
-				#interrupt-cells = <1>;
-				#address-cells = <0>;
-				#size-cells = <0>;
-				interrupt-map = </*Status*/ 0x0 &UIC0 0x18 0x4
-						/*Wake*/  0x1 &UIC1 0x1d 0x4>;
-				reg = <0xef600900 0x000000c4>;
-				local-mac-address = [000000000000]; /* Filled in by U-Boot */
-				mal-device = <&MAL0>;
-				mal-tx-channel = <0>;
-				mal-rx-channel = <0>;
-				cell-index = <0>;
-				max-frame-size = <9000>;
-				rx-fifo-size = <4096>;
-				tx-fifo-size = <2048>;
-				rx-fifo-size-gige = <16384>;
-				tx-fifo-size-gige = <16384>;
-				phy-mode = "rgmii";
-				phy-map = <0x00000000>;
-				rgmii-device = <&RGMII0>;
-				rgmii-channel = <0>;
-				has-inverted-stacr-oc;
-				has-new-stacr-staopc;
-			};
-
-			EMAC1: ethernet@ef600a00 {
-				linux,network-index = <0x1>;
-				device_type = "network";
-				compatible = "ibm,emac-405ex", "ibm,emac4sync";
-				interrupt-parent = <&EMAC1>;
-				interrupts = <0x0 0x1>;
-				#interrupt-cells = <1>;
-				#address-cells = <0>;
-				#size-cells = <0>;
-				interrupt-map = </*Status*/ 0x0 &UIC0 0x19 0x4
-						/*Wake*/  0x1 &UIC1 0x1f 0x4>;
-				reg = <0xef600a00 0x000000c4>;
-				local-mac-address = [000000000000]; /* Filled in by U-Boot */
-				mal-device = <&MAL0>;
-				mal-tx-channel = <1>;
-				mal-rx-channel = <1>;
-				cell-index = <1>;
-				max-frame-size = <9000>;
-				rx-fifo-size = <4096>;
-				tx-fifo-size = <2048>;
-				rx-fifo-size-gige = <16384>;
-				tx-fifo-size-gige = <16384>;
-				phy-mode = "rgmii";
-				phy-map = <0x00000000>;
-				rgmii-device = <&RGMII0>;
-				rgmii-channel = <1>;
-				has-inverted-stacr-oc;
-				has-new-stacr-staopc;
-			};
-
-			GPIO: gpio@ef600800 {
-				device_type = "gpio";
-				compatible = "ibm,gpio-405ex", "ibm,ppc4xx-gpio";
-				reg = <0xef600800 0x50>;
-			};
-		};
-	};
-        chosen {
-                stdout-path = "/plb/opb/serial@ef600200";
-        };
-};
diff --git a/arch/powerpc/boot/ppcboot-hotfoot.h b/arch/powerpc/boot/ppcboot-hotfoot.h
deleted file mode 100644
index 4728db95f58a..000000000000
--- a/arch/powerpc/boot/ppcboot-hotfoot.h
+++ /dev/null
@@ -1,119 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * This interface is used for compatibility with old U-boots *ONLY*.
- * Please do not imitate or extend this.
- */
-
-/* 
- * Unfortunately, the ESTeem Hotfoot board uses a mangled version of 
- * ppcboot.h for historical reasons, and in the interest of having a 
- * mainline kernel boot on the production board+bootloader, this was the 
- * least-offensive solution.  Please direct all flames to:
- *
- *  Solomon Peachy <solomon@linux-wlan.com>
- *
- * (This header is identical to ppcboot.h except for the 
- *  TARGET_HOTFOOT bits)
- */
-
-/*
- * (C) Copyright 2000, 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- */
-
-#ifndef __PPCBOOT_H__
-#define __PPCBOOT_H__
-
-/*
- * Board information passed to kernel from PPCBoot
- *
- * include/asm-ppc/ppcboot.h
- */
-
-#include "types.h"
-
-typedef struct bd_info {
-	unsigned long	bi_memstart;	/* start of DRAM memory */
-	unsigned long	bi_memsize;	/* size	 of DRAM memory in bytes */
-	unsigned long	bi_flashstart;	/* start of FLASH memory */
-	unsigned long	bi_flashsize;	/* size	 of FLASH memory */
-	unsigned long	bi_flashoffset; /* reserved area for startup monitor */
-	unsigned long	bi_sramstart;	/* start of SRAM memory */
-	unsigned long	bi_sramsize;	/* size	 of SRAM memory */
-#if defined(TARGET_8xx) || defined(TARGET_CPM2) || defined(TARGET_85xx) ||\
-	defined(TARGET_83xx)
-	unsigned long	bi_immr_base;	/* base of IMMR register */
-#endif
-#if defined(TARGET_PPC_MPC52xx)
-	unsigned long   bi_mbar_base;   /* base of internal registers */
-#endif
-	unsigned long	bi_bootflags;	/* boot / reboot flag (for LynxOS) */
-	unsigned long	bi_ip_addr;	/* IP Address */
-	unsigned char	bi_enetaddr[6];	/* Ethernet address */
-#if defined(TARGET_HOTFOOT)
-	/* second onboard ethernet port */
-	unsigned char	bi_enet1addr[6];
-#define HAVE_ENET1ADDR
-#endif /* TARGET_HOOTFOOT */
-	unsigned short	bi_ethspeed;	/* Ethernet speed in Mbps */
-	unsigned long	bi_intfreq;	/* Internal Freq, in MHz */
-	unsigned long	bi_busfreq;	/* Bus Freq, in MHz */
-#if defined(TARGET_CPM2)
-	unsigned long	bi_cpmfreq;	/* CPM_CLK Freq, in MHz */
-	unsigned long	bi_brgfreq;	/* BRG_CLK Freq, in MHz */
-	unsigned long	bi_sccfreq;	/* SCC_CLK Freq, in MHz */
-	unsigned long	bi_vco;		/* VCO Out from PLL, in MHz */
-#endif
-#if defined(TARGET_PPC_MPC52xx)
-	unsigned long   bi_ipbfreq;     /* IPB Bus Freq, in MHz */
-	unsigned long   bi_pcifreq;     /* PCI Bus Freq, in MHz */
-#endif
-	unsigned long	bi_baudrate;	/* Console Baudrate */
-#if defined(TARGET_4xx)
-	unsigned char	bi_s_version[4];	/* Version of this structure */
-	unsigned char	bi_r_version[32];	/* Version of the ROM (IBM) */
-	unsigned int	bi_procfreq;	/* CPU (Internal) Freq, in Hz */
-	unsigned int	bi_plb_busfreq;	/* PLB Bus speed, in Hz */
-	unsigned int	bi_pci_busfreq;	/* PCI Bus speed, in Hz */
-	unsigned char	bi_pci_enetaddr[6];	/* PCI Ethernet MAC address */
-#endif
-#if defined(TARGET_HOTFOOT)
-	unsigned int     bi_pllouta_freq;       /* PLL OUTA speed, in Hz */
-#endif
-#if defined(TARGET_HYMOD)
-	hymod_conf_t	bi_hymod_conf;	/* hymod configuration information */
-#endif
-#if defined(TARGET_EVB64260) || defined(TARGET_405EP) || defined(TARGET_44x) || \
-	defined(TARGET_85xx) ||	defined(TARGET_83xx) || defined(TARGET_HAS_ETH1)
-	/* second onboard ethernet port */
-	unsigned char	bi_enet1addr[6];
-#define HAVE_ENET1ADDR
-#endif
-#if defined(TARGET_EVB64260) || defined(TARGET_440GX) || \
-    defined(TARGET_85xx) || defined(TARGET_HAS_ETH2)
-	/* third onboard ethernet ports */
-	unsigned char	bi_enet2addr[6];
-#define HAVE_ENET2ADDR
-#endif
-#if defined(TARGET_440GX) || defined(TARGET_HAS_ETH3)
-	/* fourth onboard ethernet ports */
-	unsigned char	bi_enet3addr[6];
-#define HAVE_ENET3ADDR
-#endif
-#if defined(TARGET_HOTFOOT)
-        int             bi_phynum[2];           /* Determines phy mapping */
-        int             bi_phymode[2];          /* Determines phy mode */
-#endif
-#if defined(TARGET_4xx)
-	unsigned int	bi_opbfreq;		/* OB clock in Hz */
-	int		bi_iic_fast[2];		/* Use fast i2c mode */
-#endif
-#if defined(TARGET_440GX)
-	int		bi_phynum[4];		/* phy mapping */
-	int		bi_phymode[4];		/* phy mode */
-#endif
-} bd_t;
-
-#define bi_tbfreq	bi_intfreq
-
-#endif	/* __PPCBOOT_H__ */
diff --git a/arch/powerpc/boot/ppcboot.h b/arch/powerpc/boot/ppcboot.h
index a78b0b257698..90c8f452fe6e 100644
--- a/arch/powerpc/boot/ppcboot.h
+++ b/arch/powerpc/boot/ppcboot.h
@@ -63,7 +63,7 @@ typedef struct bd_info {
 #if defined(TARGET_HYMOD)
 	hymod_conf_t	bi_hymod_conf;	/* hymod configuration information */
 #endif
-#if defined(TARGET_EVB64260) || defined(TARGET_405EP) || defined(TARGET_44x) || \
+#if defined(TARGET_EVB64260) || defined(TARGET_44x) || \
 	defined(TARGET_85xx) ||	defined(TARGET_83xx) || defined(TARGET_HAS_ETH1)
 	/* second onboard ethernet port */
 	unsigned char	bi_enet1addr[6];
