@@ -109,7 +109,7 @@
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
- compatible = "fsl,mpc8315-immr", "simple-bus";
+ compatible = "fsl,mpc8308-immr", "simple-bus";
ranges = <0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <0>;
@@ -35,6 +35,8 @@
/* system i/o configuration register high */
#define MPC83XX_SICRH_OFFS 0x118
+#define MPC8308_SICRH_USB_MASK 0x000c0000
+#define MPC8308_SICRH_USB_ULPI 0x00040000
#define MPC834X_SICRH_USB_UTMI 0x00020000
#define MPC831X_SICRH_USB_MASK 0x000000e0
#define MPC831X_SICRH_USB_ULPI 0x000000a0
@@ -127,7 +127,8 @@ int mpc831x_usb_cfg(void)
/* Configure clock */
immr_node = of_get_parent(np);
- if (immr_node && of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
+ if (immr_node && (of_device_is_compatible(immr_node, "fsl,mpc8315-immr") ||
+ of_device_is_compatible(immr_node, "fsl,mpc8308-immr")))
clrsetbits_be32(immap + MPC83XX_SCCR_OFFS,
MPC8315_SCCR_USB_MASK,
MPC8315_SCCR_USB_DRCM_01);
@@ -138,7 +139,11 @@ int mpc831x_usb_cfg(void)
/* Configure pin mux for ULPI. There is no pin mux for UTMI */
if (prop && !strcmp(prop, "ulpi")) {
- if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
+ if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+ clrsetbits_be32(immap + MPC83XX_SICRH_OFFS,
+ MPC8308_SICRH_USB_MASK,
+ MPC8308_SICRH_USB_ULPI);
+ } else if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr")) {
clrsetbits_be32(immap + MPC83XX_SICRL_OFFS,
MPC8315_SICRL_USB_MASK,
MPC8315_SICRL_USB_ULPI);
@@ -173,6 +178,9 @@ int mpc831x_usb_cfg(void)
!strcmp(prop, "utmi"))) {
u32 refsel;
+ if (of_device_is_compatible(immr_node, "fsl,mpc8308-immr"))
+ goto out;
+
if (of_device_is_compatible(immr_node, "fsl,mpc8315-immr"))
refsel = CONTROL_REFSEL_24MHZ;
else
@@ -186,9 +194,11 @@ int mpc831x_usb_cfg(void)
temp = CONTROL_PHY_CLK_SEL_ULPI;
#ifdef CONFIG_USB_OTG
/* Set OTG_PORT */
- dr_mode = of_get_property(np, "dr_mode", NULL);
- if (dr_mode && !strcmp(dr_mode, "otg"))
- temp |= CONTROL_OTG_PORT;
+ if (!of_device_is_compatible(immr_node, "fsl,mpc8308-immr")) {
+ dr_mode = of_get_property(np, "dr_mode", NULL);
+ if (dr_mode && !strcmp(dr_mode, "otg"))
+ temp |= CONTROL_OTG_PORT;
+ }
#endif /* CONFIG_USB_OTG */
out_be32(usb_regs + FSL_USB2_CONTROL_OFFS, temp);
} else {
@@ -196,6 +206,7 @@ int mpc831x_usb_cfg(void)
ret = -EINVAL;
}
+out:
iounmap(usb_regs);
of_node_put(np);
return ret;
MPC8308 has ULPI pin muxing settings in SICRH register, bits 17-18 which is different from both MPC8313 and MPC8315. Also MPC8308 doesn't have REFSEL, UTMI_PHY_EN and OTG_PORT fields in the USB DR controller CONTROL register. Signed-off-by: Ilya Yanok <yanok@emcraft.com> --- arch/powerpc/boot/dts/mpc8308rdb.dts | 2 +- arch/powerpc/platforms/83xx/mpc83xx.h | 2 ++ arch/powerpc/platforms/83xx/usb.c | 21 ++++++++++++++++----- 3 files changed, 19 insertions(+), 6 deletions(-)