Message ID | cover.1680663252.git.Takahiro.Kuwano@infineon.com |
---|---|
Headers | show |
Series | mtd: hyperbus: Add support for Infineon S26Hx-T | expand |
Hi, Takahiro, Vignesh, On 07.04.2023 09:11, tkuw584924@gmail.com wrote: > From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> > > This sereis adds support for Infineon S26HL-T/S26HS-T flash family. > https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 > > This family supports two interface modes, SPI mode and Hyperbus mode. The mode > can be switched at rutime. The default mode is selected by ordering option > and non-volatile user configuration. In hyperbus mode, the device is compatible > with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of > use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch > set focuses on particular usage that the device is pre-configured as hyperbus > mode for compatibility with S26Kx-S. I'm questioning the overall hyperbus software architecture, not your patches per se. IMO hyperbus framework should have been written on top of SPIMEM and the controllers be placed in drivers/spi/. So I'd first address the SPIMEM adoption before adding/accepting new support. Would love to hear more from Vignesh. Cheers, ta
+ Sergei, Geert, Mark & linux-spi Hi, Sergei, On 23.05.2023 07:22, Tudor Ambarus wrote: > Hi, Takahiro, Vignesh, > > > On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >> >> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >> >> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >> can be switched at rutime. The default mode is selected by ordering option >> and non-volatile user configuration. In hyperbus mode, the device is compatible >> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >> set focuses on particular usage that the device is pre-configured as hyperbus >> mode for compatibility with S26Kx-S. > > I'm questioning the overall hyperbus software architecture, not your > patches per se. IMO hyperbus framework should have been written on top > of SPIMEM and the controllers be placed in drivers/spi/. So I'd first > address the SPIMEM adoption before adding/accepting new support. Would > love to hear more from Vignesh. > RPC is the only multi IO SPI controller that's upstreamed and capable of dealing with hyperflashes, but there are others which are not upstreamed yet (microchip). Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct spi_mem_op`` [2] which could have been avoided if hyperflash driver was extended with SPI MEM support. This way the RPC hyperbus driver, which is an SPI controller, could have been moved to drivers/spi. Sergei, do you remember why we haven't used SPI MEM for hyberbus since the beginning? Was it something that we aimed for in a future patch set? Thanks, ta [1] https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 [2] https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99
Ah, Sergei's email was bouncing, I updated his email address. Sergei, would you please read the thread? Thanks! On 22.01.2024 08:11, Tudor Ambarus wrote: > + Sergei, Geert, Mark & linux-spi > > Hi, Sergei, > > On 23.05.2023 07:22, Tudor Ambarus wrote: >> Hi, Takahiro, Vignesh, >> >> >> On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >>> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >>> >>> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >>> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >>> >>> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >>> can be switched at rutime. The default mode is selected by ordering option >>> and non-volatile user configuration. In hyperbus mode, the device is compatible >>> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >>> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >>> set focuses on particular usage that the device is pre-configured as hyperbus >>> mode for compatibility with S26Kx-S. >> >> I'm questioning the overall hyperbus software architecture, not your >> patches per se. IMO hyperbus framework should have been written on top >> of SPIMEM and the controllers be placed in drivers/spi/. So I'd first >> address the SPIMEM adoption before adding/accepting new support. Would >> love to hear more from Vignesh. >> > > RPC is the only multi IO SPI controller that's upstreamed and capable of > dealing with hyperflashes, but there are others which are not upstreamed > yet (microchip). > > Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct > spi_mem_op`` [2] which could have been avoided if hyperflash driver was > extended with SPI MEM support. This way the RPC hyperbus driver, which > is an SPI controller, could have been moved to drivers/spi. > > Sergei, do you remember why we haven't used SPI MEM for hyberbus since > the beginning? Was it something that we aimed for in a future patch set? > > Thanks, > ta > > [1] > https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 > > [2] > https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99 >
On 1/22/2024 11:41 AM, Tudor Ambarus wrote: > + Sergei, Geert, Mark & linux-spi > > Hi, Sergei, > > On 23.05.2023 07:22, Tudor Ambarus wrote: >> Hi, Takahiro, Vignesh, >> >> >> On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >>> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >>> >>> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >>> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >>> >>> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >>> can be switched at rutime. The default mode is selected by ordering option >>> and non-volatile user configuration. In hyperbus mode, the device is compatible >>> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >>> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >>> set focuses on particular usage that the device is pre-configured as hyperbus >>> mode for compatibility with S26Kx-S. >> >> I'm questioning the overall hyperbus software architecture, not your >> patches per se. IMO hyperbus framework should have been written on top >> of SPIMEM and the controllers be placed in drivers/spi/. So I'd first >> address the SPIMEM adoption before adding/accepting new support. Would >> love to hear more from Vignesh. >> > > RPC is the only multi IO SPI controller that's upstreamed and capable of > dealing with hyperflashes, but there are others which are not upstreamed > yet (microchip). > > Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct > spi_mem_op`` [2] which could have been avoided if hyperflash driver was > extended with SPI MEM support. This way the RPC hyperbus driver, which > is an SPI controller, could have been moved to drivers/spi. > > Sergei, do you remember why we haven't used SPI MEM for hyberbus since > the beginning? Was it something that we aimed for in a future patch set? > > Thanks, > ta > > [1] > https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 > > [2] > https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99 > The initial hyperflash predates opening up of HyperBus protocol and inclusion of it in xSPI spec. First gen Flashes followed CFI specification and hence made sense to make use of cfi_cmdset_0002.c We did have a discussion on extending spi_mem to support xSPI profile 2.0 during the RPC_IF [3] [4]. Overall, both Controllers and Flashes have moved away from CFI parallel flash protocol over to xSPI / SPI NOR flash protocol (profile 2.0), so I agree with Tudor's assessment that we need to move towards spi_mem in longer term. So a) Extend spi_mem_op to support xSPI profile 2.0 transaction template b) HyperBus layer can then either be a adapter from CFI to spi_mem for CFI compliant devices. And be subsumed completely within SPI NOR for SFDP compliant devices. c) Move the existing controllers over to new framework. [3] https://lore.kernel.org/all/b8224f46-fc2e-de35-0a90-a2a86cacb489@ti.com/ [4] https://lore.kernel.org/all/20200220084927.7a411d40@collabora.com/
On 1/22/24 06:25, Raghavendra, Vignesh wrote: > > > On 1/22/2024 11:41 AM, Tudor Ambarus wrote: >> + Sergei, Geert, Mark & linux-spi >> >> Hi, Sergei, >> >> On 23.05.2023 07:22, Tudor Ambarus wrote: >>> Hi, Takahiro, Vignesh, >>> >>> >>> On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >>>> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >>>> >>>> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >>>> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >>>> >>>> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >>>> can be switched at rutime. The default mode is selected by ordering option >>>> and non-volatile user configuration. In hyperbus mode, the device is compatible >>>> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >>>> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >>>> set focuses on particular usage that the device is pre-configured as hyperbus >>>> mode for compatibility with S26Kx-S. >>> >>> I'm questioning the overall hyperbus software architecture, not your >>> patches per se. IMO hyperbus framework should have been written on top >>> of SPIMEM and the controllers be placed in drivers/spi/. So I'd first >>> address the SPIMEM adoption before adding/accepting new support. Would >>> love to hear more from Vignesh. >>> >> >> RPC is the only multi IO SPI controller that's upstreamed and capable of >> dealing with hyperflashes, but there are others which are not upstreamed >> yet (microchip). >> >> Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct >> spi_mem_op`` [2] which could have been avoided if hyperflash driver was >> extended with SPI MEM support. This way the RPC hyperbus driver, which >> is an SPI controller, could have been moved to drivers/spi. >> >> Sergei, do you remember why we haven't used SPI MEM for hyberbus since >> the beginning? Was it something that we aimed for in a future patch set? >> >> Thanks, >> ta >> >> [1] >> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 >> >> [2] >> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99 >> > > The initial hyperflash predates opening up of HyperBus protocol and > inclusion of it in xSPI spec. First gen Flashes followed CFI specification > and hence made sense to make use of cfi_cmdset_0002.c > > We did have a discussion on extending spi_mem to support xSPI profile > 2.0 during the RPC_IF [3] [4]. > > Overall, both Controllers and Flashes have moved away from CFI parallel > flash protocol over to xSPI / SPI NOR flash protocol (profile 2.0), so I > agree with Tudor's assessment that we need to move towards spi_mem in > longer term. So > Good, thanks Vignesh! I'll study a bit more and let you know about the progress on this topic. Cheers, ta > a) Extend spi_mem_op to support xSPI profile 2.0 transaction template > b) HyperBus layer can then either be a adapter from CFI to spi_mem for CFI > compliant devices. And be subsumed completely within SPI NOR for SFDP > compliant devices. > c) Move the existing controllers over to new framework. > > > [3] https://lore.kernel.org/all/b8224f46-fc2e-de35-0a90-a2a86cacb489@ti.com/ > [4] https://lore.kernel.org/all/20200220084927.7a411d40@collabora.com/ >
On 1/22/24 09:13, Tudor Ambarus wrote: > > > On 1/22/24 06:25, Raghavendra, Vignesh wrote: >> >> >> On 1/22/2024 11:41 AM, Tudor Ambarus wrote: >>> + Sergei, Geert, Mark & linux-spi >>> >>> Hi, Sergei, >>> >>> On 23.05.2023 07:22, Tudor Ambarus wrote: >>>> Hi, Takahiro, Vignesh, >>>> >>>> >>>> On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >>>>> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >>>>> >>>>> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >>>>> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >>>>> >>>>> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >>>>> can be switched at rutime. The default mode is selected by ordering option >>>>> and non-volatile user configuration. In hyperbus mode, the device is compatible >>>>> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >>>>> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >>>>> set focuses on particular usage that the device is pre-configured as hyperbus >>>>> mode for compatibility with S26Kx-S. >>>> >>>> I'm questioning the overall hyperbus software architecture, not your >>>> patches per se. IMO hyperbus framework should have been written on top >>>> of SPIMEM and the controllers be placed in drivers/spi/. So I'd first >>>> address the SPIMEM adoption before adding/accepting new support. Would >>>> love to hear more from Vignesh. >>>> >>> >>> RPC is the only multi IO SPI controller that's upstreamed and capable of >>> dealing with hyperflashes, but there are others which are not upstreamed >>> yet (microchip). >>> >>> Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct >>> spi_mem_op`` [2] which could have been avoided if hyperflash driver was >>> extended with SPI MEM support. This way the RPC hyperbus driver, which >>> is an SPI controller, could have been moved to drivers/spi. >>> >>> Sergei, do you remember why we haven't used SPI MEM for hyberbus since >>> the beginning? Was it something that we aimed for in a future patch set? >>> >>> Thanks, >>> ta >>> >>> [1] >>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 >>> >>> [2] >>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99 >>> >> >> The initial hyperflash predates opening up of HyperBus protocol and >> inclusion of it in xSPI spec. First gen Flashes followed CFI specification >> and hence made sense to make use of cfi_cmdset_0002.c >> >> We did have a discussion on extending spi_mem to support xSPI profile >> 2.0 during the RPC_IF [3] [4]. >> >> Overall, both Controllers and Flashes have moved away from CFI parallel >> flash protocol over to xSPI / SPI NOR flash protocol (profile 2.0), so I >> agree with Tudor's assessment that we need to move towards spi_mem in >> longer term. So >> > > Good, thanks Vignesh! I'll study a bit more and let you know about the > progress on this topic. Hi All At STMicroelectronics we got an OSPI block which is supporting both OSPI and HyperBus protocol similarly to the mentioned RPC-IF. This means that we intend to split our implementation in 3 drivers as RPC-IF: _ backend driver including common source code to OSPI and HyperBus _ OSPI frontend driver _ HyperBus frontend driver Following this discussion thread, we are wondering if it will be the right direction to choose in order to propose this implementation to MTD mailing list. Have you an idea about time scale regarding the HyperBus migration over spi-mem ? Thanks Patrice > > Cheers, > ta > >> a) Extend spi_mem_op to support xSPI profile 2.0 transaction template >> b) HyperBus layer can then either be a adapter from CFI to spi_mem for CFI >> compliant devices. And be subsumed completely within SPI NOR for SFDP >> compliant devices. >> c) Move the existing controllers over to new framework. >> >> >> [3] https://lore.kernel.org/all/b8224f46-fc2e-de35-0a90-a2a86cacb489@ti.com/ >> [4] https://lore.kernel.org/all/20200220084927.7a411d40@collabora.com/ >> > > ______________________________________________________ > Linux MTD discussion mailing list > http://lists.infradead.org/mailman/listinfo/linux-mtd/
On 2/1/24 10:46, Patrice CHOTARD wrote: > > > On 1/22/24 09:13, Tudor Ambarus wrote: >> >> >> On 1/22/24 06:25, Raghavendra, Vignesh wrote: >>> >>> >>> On 1/22/2024 11:41 AM, Tudor Ambarus wrote: >>>> + Sergei, Geert, Mark & linux-spi >>>> >>>> Hi, Sergei, >>>> >>>> On 23.05.2023 07:22, Tudor Ambarus wrote: >>>>> Hi, Takahiro, Vignesh, >>>>> >>>>> >>>>> On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >>>>>> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >>>>>> >>>>>> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >>>>>> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >>>>>> >>>>>> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >>>>>> can be switched at rutime. The default mode is selected by ordering option >>>>>> and non-volatile user configuration. In hyperbus mode, the device is compatible >>>>>> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >>>>>> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >>>>>> set focuses on particular usage that the device is pre-configured as hyperbus >>>>>> mode for compatibility with S26Kx-S. >>>>> >>>>> I'm questioning the overall hyperbus software architecture, not your >>>>> patches per se. IMO hyperbus framework should have been written on top >>>>> of SPIMEM and the controllers be placed in drivers/spi/. So I'd first >>>>> address the SPIMEM adoption before adding/accepting new support. Would >>>>> love to hear more from Vignesh. >>>>> >>>> >>>> RPC is the only multi IO SPI controller that's upstreamed and capable of >>>> dealing with hyperflashes, but there are others which are not upstreamed >>>> yet (microchip). >>>> >>>> Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct >>>> spi_mem_op`` [2] which could have been avoided if hyperflash driver was >>>> extended with SPI MEM support. This way the RPC hyperbus driver, which >>>> is an SPI controller, could have been moved to drivers/spi. >>>> >>>> Sergei, do you remember why we haven't used SPI MEM for hyberbus since >>>> the beginning? Was it something that we aimed for in a future patch set? >>>> >>>> Thanks, >>>> ta >>>> >>>> [1] >>>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 >>>> >>>> [2] >>>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99 >>>> >>> >>> The initial hyperflash predates opening up of HyperBus protocol and >>> inclusion of it in xSPI spec. First gen Flashes followed CFI specification >>> and hence made sense to make use of cfi_cmdset_0002.c >>> >>> We did have a discussion on extending spi_mem to support xSPI profile >>> 2.0 during the RPC_IF [3] [4]. >>> >>> Overall, both Controllers and Flashes have moved away from CFI parallel >>> flash protocol over to xSPI / SPI NOR flash protocol (profile 2.0), so I >>> agree with Tudor's assessment that we need to move towards spi_mem in >>> longer term. So >>> >> >> Good, thanks Vignesh! I'll study a bit more and let you know about the >> progress on this topic. > > Hi All Hi, > > At STMicroelectronics we got an OSPI block which is supporting both OSPI and HyperBus protocol > similarly to the mentioned RPC-IF. > > This means that we intend to split our implementation in 3 drivers as RPC-IF: > _ backend driver including common source code to OSPI and HyperBus > _ OSPI frontend driver > _ HyperBus frontend driver > > Following this discussion thread, we are wondering if it will be the right direction to > choose in order to propose this implementation to MTD mailing list. I think the right direction would be to have hyperflash on top of SPIMEM, and the SPI controller under drivers/spi. > > Have you an idea about time scale regarding the HyperBus migration over spi-mem ? > No, sorry. It's at best effort from my side. Happy to review proposals though. > Thanks > Patrice > > >> >> Cheers, >> ta >> >>> a) Extend spi_mem_op to support xSPI profile 2.0 transaction template >>> b) HyperBus layer can then either be a adapter from CFI to spi_mem for CFI >>> compliant devices. And be subsumed completely within SPI NOR for SFDP >>> compliant devices. >>> c) Move the existing controllers over to new framework. >>> >>> >>> [3] https://lore.kernel.org/all/b8224f46-fc2e-de35-0a90-a2a86cacb489@ti.com/ >>> [4] https://lore.kernel.org/all/20200220084927.7a411d40@collabora.com/ >>> >> >> ______________________________________________________ >> Linux MTD discussion mailing list >> http://lists.infradead.org/mailman/listinfo/linux-mtd/
On 2/1/24 13:02, Tudor Ambarus wrote: > > > On 2/1/24 10:46, Patrice CHOTARD wrote: >> >> >> On 1/22/24 09:13, Tudor Ambarus wrote: >>> >>> >>> On 1/22/24 06:25, Raghavendra, Vignesh wrote: >>>> >>>> >>>> On 1/22/2024 11:41 AM, Tudor Ambarus wrote: >>>>> + Sergei, Geert, Mark & linux-spi >>>>> >>>>> Hi, Sergei, >>>>> >>>>> On 23.05.2023 07:22, Tudor Ambarus wrote: >>>>>> Hi, Takahiro, Vignesh, >>>>>> >>>>>> >>>>>> On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >>>>>>> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >>>>>>> >>>>>>> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >>>>>>> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >>>>>>> >>>>>>> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >>>>>>> can be switched at rutime. The default mode is selected by ordering option >>>>>>> and non-volatile user configuration. In hyperbus mode, the device is compatible >>>>>>> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >>>>>>> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >>>>>>> set focuses on particular usage that the device is pre-configured as hyperbus >>>>>>> mode for compatibility with S26Kx-S. >>>>>> >>>>>> I'm questioning the overall hyperbus software architecture, not your >>>>>> patches per se. IMO hyperbus framework should have been written on top >>>>>> of SPIMEM and the controllers be placed in drivers/spi/. So I'd first >>>>>> address the SPIMEM adoption before adding/accepting new support. Would >>>>>> love to hear more from Vignesh. >>>>>> >>>>> >>>>> RPC is the only multi IO SPI controller that's upstreamed and capable of >>>>> dealing with hyperflashes, but there are others which are not upstreamed >>>>> yet (microchip). >>>>> >>>>> Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct >>>>> spi_mem_op`` [2] which could have been avoided if hyperflash driver was >>>>> extended with SPI MEM support. This way the RPC hyperbus driver, which >>>>> is an SPI controller, could have been moved to drivers/spi. >>>>> >>>>> Sergei, do you remember why we haven't used SPI MEM for hyberbus since >>>>> the beginning? Was it something that we aimed for in a future patch set? >>>>> >>>>> Thanks, >>>>> ta >>>>> >>>>> [1] >>>>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 >>>>> >>>>> [2] >>>>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99 >>>>> >>>> >>>> The initial hyperflash predates opening up of HyperBus protocol and >>>> inclusion of it in xSPI spec. First gen Flashes followed CFI specification >>>> and hence made sense to make use of cfi_cmdset_0002.c >>>> >>>> We did have a discussion on extending spi_mem to support xSPI profile >>>> 2.0 during the RPC_IF [3] [4]. >>>> >>>> Overall, both Controllers and Flashes have moved away from CFI parallel >>>> flash protocol over to xSPI / SPI NOR flash protocol (profile 2.0), so I >>>> agree with Tudor's assessment that we need to move towards spi_mem in >>>> longer term. So >>>> >>> >>> Good, thanks Vignesh! I'll study a bit more and let you know about the >>> progress on this topic. >> >> Hi All > > Hi, > >> >> At STMicroelectronics we got an OSPI block which is supporting both OSPI and HyperBus protocol >> similarly to the mentioned RPC-IF. >> >> This means that we intend to split our implementation in 3 drivers as RPC-IF: >> _ backend driver including common source code to OSPI and HyperBus >> _ OSPI frontend driver >> _ HyperBus frontend driver >> >> Following this discussion thread, we are wondering if it will be the right direction to >> choose in order to propose this implementation to MTD mailing list. > > I think the right direction would be to have hyperflash on top of > SPIMEM, and the SPI controller under drivers/spi. To be more precise, when you say "would be to have", you mean you will NAK an implementation in 3 drivers as RPC-IF ? Patrice >> >> Have you an idea about time scale regarding the HyperBus migration over spi-mem ? >> > > No, sorry. It's at best effort from my side. Happy to review proposals > though. > >> Thanks >> Patrice >> >> >>> >>> Cheers, >>> ta >>> >>>> a) Extend spi_mem_op to support xSPI profile 2.0 transaction template >>>> b) HyperBus layer can then either be a adapter from CFI to spi_mem for CFI >>>> compliant devices. And be subsumed completely within SPI NOR for SFDP >>>> compliant devices. >>>> c) Move the existing controllers over to new framework. >>>> >>>> >>>> [3] https://lore.kernel.org/all/b8224f46-fc2e-de35-0a90-a2a86cacb489@ti.com/ >>>> [4] https://lore.kernel.org/all/20200220084927.7a411d40@collabora.com/ >>>> >>> >>> ______________________________________________________ >>> Linux MTD discussion mailing list >>> http://lists.infradead.org/mailman/listinfo/linux-mtd/
On 2/1/24 12:23, Patrice CHOTARD wrote: > > > On 2/1/24 13:02, Tudor Ambarus wrote: >> >> >> On 2/1/24 10:46, Patrice CHOTARD wrote: >>> >>> >>> On 1/22/24 09:13, Tudor Ambarus wrote: >>>> >>>> >>>> On 1/22/24 06:25, Raghavendra, Vignesh wrote: >>>>> >>>>> >>>>> On 1/22/2024 11:41 AM, Tudor Ambarus wrote: >>>>>> + Sergei, Geert, Mark & linux-spi >>>>>> >>>>>> Hi, Sergei, >>>>>> >>>>>> On 23.05.2023 07:22, Tudor Ambarus wrote: >>>>>>> Hi, Takahiro, Vignesh, >>>>>>> >>>>>>> >>>>>>> On 07.04.2023 09:11, tkuw584924@gmail.com wrote: >>>>>>>> From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> >>>>>>>> >>>>>>>> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. >>>>>>>> https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 >>>>>>>> >>>>>>>> This family supports two interface modes, SPI mode and Hyperbus mode. The mode >>>>>>>> can be switched at rutime. The default mode is selected by ordering option >>>>>>>> and non-volatile user configuration. In hyperbus mode, the device is compatible >>>>>>>> with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of >>>>>>>> use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch >>>>>>>> set focuses on particular usage that the device is pre-configured as hyperbus >>>>>>>> mode for compatibility with S26Kx-S. >>>>>>> >>>>>>> I'm questioning the overall hyperbus software architecture, not your >>>>>>> patches per se. IMO hyperbus framework should have been written on top >>>>>>> of SPIMEM and the controllers be placed in drivers/spi/. So I'd first >>>>>>> address the SPIMEM adoption before adding/accepting new support. Would >>>>>>> love to hear more from Vignesh. >>>>>>> >>>>>> >>>>>> RPC is the only multi IO SPI controller that's upstreamed and capable of >>>>>> dealing with hyperflashes, but there are others which are not upstreamed >>>>>> yet (microchip). >>>>>> >>>>>> Struct ``struct rpcif_op`` [1] duplicates the contents of ``struct >>>>>> spi_mem_op`` [2] which could have been avoided if hyperflash driver was >>>>>> extended with SPI MEM support. This way the RPC hyperbus driver, which >>>>>> is an SPI controller, could have been moved to drivers/spi. >>>>>> >>>>>> Sergei, do you remember why we haven't used SPI MEM for hyberbus since >>>>>> the beginning? Was it something that we aimed for in a future patch set? >>>>>> >>>>>> Thanks, >>>>>> ta >>>>>> >>>>>> [1] >>>>>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/memory/renesas-rpc-if.h?h=mtd/for-6.8#n22 >>>>>> >>>>>> [2] >>>>>> https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git/tree/include/linux/spi/spi-mem.h?h=mtd/for-6.8#n99 >>>>>> >>>>> >>>>> The initial hyperflash predates opening up of HyperBus protocol and >>>>> inclusion of it in xSPI spec. First gen Flashes followed CFI specification >>>>> and hence made sense to make use of cfi_cmdset_0002.c >>>>> >>>>> We did have a discussion on extending spi_mem to support xSPI profile >>>>> 2.0 during the RPC_IF [3] [4]. >>>>> >>>>> Overall, both Controllers and Flashes have moved away from CFI parallel >>>>> flash protocol over to xSPI / SPI NOR flash protocol (profile 2.0), so I >>>>> agree with Tudor's assessment that we need to move towards spi_mem in >>>>> longer term. So >>>>> >>>> >>>> Good, thanks Vignesh! I'll study a bit more and let you know about the >>>> progress on this topic. >>> >>> Hi All >> >> Hi, >> >>> >>> At STMicroelectronics we got an OSPI block which is supporting both OSPI and HyperBus protocol >>> similarly to the mentioned RPC-IF. >>> >>> This means that we intend to split our implementation in 3 drivers as RPC-IF: >>> _ backend driver including common source code to OSPI and HyperBus >>> _ OSPI frontend driver >>> _ HyperBus frontend driver >>> >>> Following this discussion thread, we are wondering if it will be the right direction to >>> choose in order to propose this implementation to MTD mailing list. >> >> I think the right direction would be to have hyperflash on top of >> SPIMEM, and the SPI controller under drivers/spi. > > > To be more precise, when you say "would be to have", you mean you will NAK > an implementation in 3 drivers as RPC-IF ? > Yes. I think we should move towards SPIMEM adoption, don't you? > >>> >>> Have you an idea about time scale regarding the HyperBus migration over spi-mem ? >>> >> >> No, sorry. It's at best effort from my side. Happy to review proposals >> though. >> >>> Thanks >>> Patrice >>> >>> >>>> >>>> Cheers, >>>> ta >>>> >>>>> a) Extend spi_mem_op to support xSPI profile 2.0 transaction template >>>>> b) HyperBus layer can then either be a adapter from CFI to spi_mem for CFI >>>>> compliant devices. And be subsumed completely within SPI NOR for SFDP >>>>> compliant devices. >>>>> c) Move the existing controllers over to new framework. >>>>> >>>>> >>>>> [3] https://lore.kernel.org/all/b8224f46-fc2e-de35-0a90-a2a86cacb489@ti.com/ >>>>> [4] https://lore.kernel.org/all/20200220084927.7a411d40@collabora.com/ >>>>> >>>> >>>> ______________________________________________________ >>>> Linux MTD discussion mailing list >>>> http://lists.infradead.org/mailman/listinfo/linux-mtd/
From: Takahiro Kuwano <Takahiro.Kuwano@infineon.com> This sereis adds support for Infineon S26HL-T/S26HS-T flash family. https://www.infineon.com/dgdl/Infineon-S26HS01GTGABHM020-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7f2a768a017f52f2f5182c91 This family supports two interface modes, SPI mode and Hyperbus mode. The mode can be switched at rutime. The default mode is selected by ordering option and non-volatile user configuration. In hyperbus mode, the device is compatible with S26KL-S/S26KS-S hyperflash family that supports hyperbus only so one of use cases of S26Hx-T is replacement of (or migration from) S26Kx-S. This patch set focuses on particular usage that the device is pre-configured as hyperbus mode for compatibility with S26Kx-S. Runtime mode switch between SPI and Hyperbus may be added as needed basis with spi-mem framework and controller support. Takahiro Kuwano (2): mtd: hyperbus: Introduce SFDP probe mtd: chips: cfi_cmdset0002: Fixups for Infineon(Cypress) S26Hx drivers/mtd/chips/cfi_cmdset_0002.c | 25 ++ drivers/mtd/hyperbus/Makefile | 4 +- drivers/mtd/hyperbus/hyperbus-core.c | 15 +- drivers/mtd/hyperbus/hyperbus-sfdp.c | 346 +++++++++++++++++++++++++++ include/linux/mtd/cfi.h | 1 + 5 files changed, 389 insertions(+), 2 deletions(-) create mode 100644 drivers/mtd/hyperbus/hyperbus-sfdp.c