diff mbox

[v5,2/4] i2c: add support for Diolan DLN-2 USB-I2C adapter

Message ID 1411158165-25794-3-git-send-email-octavian.purdila@intel.com
State Not Applicable, archived
Headers show

Commit Message

Octavian Purdila Sept. 19, 2014, 8:22 p.m. UTC
From: Laurentiu Palcu <laurentiu.palcu@intel.com>

This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.

Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
---
 drivers/i2c/busses/Kconfig    |  10 ++
 drivers/i2c/busses/Makefile   |   1 +
 drivers/i2c/busses/i2c-dln2.c | 383 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 394 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-dln2.c

Comments

Johan Hovold Sept. 24, 2014, 10:58 a.m. UTC | #1
On Fri, Sep 19, 2014 at 11:22:43PM +0300, Octavian Purdila wrote:

> +struct dln2_i2c {
> +	struct platform_device *pdev;
> +	struct i2c_adapter adapter;
> +	u32 freq;
> +	u32 min_freq;
> +	u32 max_freq;
> +	/*
> +	 * Buffer to hold the packet for read or write transfers. One
> +	 * is enough since we can't have multiple transfers in
> +	 * parallel on the i2c adapter.
> +	 */
> +	union {
> +		struct {
> +			u8 port;
> +			u8 addr;
> +			u8 mem_addr_len;
> +			__le32 mem_addr;
> +			__le16 buf_len;
> +			u8 buf[DLN2_I2C_MAX_XFER_SIZE];
> +		} __packed tx;
> +		struct {
> +			__le16 buf_len;
> +			u8 buf[DLN2_I2C_MAX_XFER_SIZE];
> +		} __packed rx;
> +	} *buf;

Please declare these structs separately from the dln2_i2c struct so you
can use temporary pointers below.

Perhaps just allocate a large enough buffer (or page) here and keep you
transfer-buffer declarations in the two functions where they are used if
you prefer.

> +};
>
> +static int dln2_i2c_enable(struct dln2_i2c *dln2, bool enable)
> +{
> +	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
> +	int ret;
> +	u8 port;
> +	u16 cmd;
> +
> +	port = pdata->port;

Store the port number in the dln2_i2c struct rather than access it
through the platform data for every I/O operation.

> +
> +	if (enable)
> +		cmd = DLN2_I2C_ENABLE;
> +	else
> +		cmd = DLN2_I2C_DISABLE;
> +
> +	ret = dln2_transfer(dln2->pdev, cmd, &port, sizeof(port), NULL, NULL);
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int dln2_i2c_set_frequency(struct dln2_i2c *dln2, u32 freq)
> +{
> +	int ret;
> +	struct tx_data {
> +		u8 port;
> +		__le32 freq;
> +	} __packed tx;
> +	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
> +
> +	tx.port = pdata->port;
> +	tx.freq = cpu_to_le32(freq);
> +
> +	ret = dln2_transfer(dln2->pdev, DLN2_I2C_SET_FREQUENCY, &tx, sizeof(tx),
> +			    NULL, NULL);
> +	if (ret < 0)
> +		return ret;
> +
> +	dln2->freq = freq;
> +
> +	return 0;
> +}
> +
> +static int dln2_i2c_get_freq(struct dln2_i2c *dln2, u16 cmd, u32 *res)
> +{
> +	int ret;
> +	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
> +	u8 port = pdata->port;
> +	__le32 freq;
> +	unsigned len = sizeof(freq);
> +
> +	ret = dln2_transfer(dln2->pdev, cmd, &port, sizeof(port),
> +			    &freq, &len);
> +	if (ret < 0)
> +		return ret;
> +	if (len < sizeof(freq))
> +		return -EPROTO;
> +
> +	*res = le32_to_cpu(freq);
> +
> +	return 0;
> +}
> +
> +static int dln2_i2c_setup(struct dln2_i2c *dln2)
> +{
> +	int ret;
> +
> +	ret = dln2_i2c_enable(dln2, false);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = dln2_i2c_get_freq(dln2, DLN2_I2C_GET_MIN_FREQUENCY,
> +				&dln2->min_freq);
> +	if (ret < 0)
> +		return 0;

return ret

> +
> +	ret = dln2_i2c_get_freq(dln2, DLN2_I2C_GET_MAX_FREQUENCY,
> +				&dln2->max_freq);
> +	if (ret < 0)
> +		return 0;

return ret

> +
> +	ret = dln2_i2c_set_frequency(dln2, DLN2_I2C_FREQ_STD);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = dln2_i2c_enable(dln2, true);
> +
> +	return ret;
> +}
> +
> +static int dln2_i2c_write(struct dln2_i2c *dln2, u8 addr,
> +			  u8 *data, u16 data_len)
> +{
> +	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
> +	int ret;
> +	unsigned len;
> +
> +	dln2->buf->tx.port = pdata->port;
> +	dln2->buf->tx.addr = addr;
> +	dln2->buf->tx.mem_addr_len = 0;
> +	dln2->buf->tx.mem_addr = 0;
> +	dln2->buf->tx.buf_len = cpu_to_le16(data_len);
> +	memcpy(dln2->buf->tx.buf, data, data_len);
> +
> +	len = sizeof(dln2->buf->tx) + data_len - DLN2_I2C_MAX_XFER_SIZE;
> +	ret = dln2_transfer(dln2->pdev, DLN2_I2C_WRITE, &dln2->buf->tx, len,
> +			    NULL, NULL);

Use a temporary pointer to the tx struct above for readability.

> +	if (ret < 0)
> +		return ret;
> +
> +	return data_len;
> +}
> +
> +static int dln2_i2c_read(struct dln2_i2c *dln2, u16 addr, u8 *data,
> +			 u16 data_len)
> +{
> +	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
> +	int ret;
> +	struct {
> +		u8 port;
> +		u8 addr;
> +		u8 mem_addr_len;
> +		__le32 mem_addr;
> +		__le16 buf_len;
> +	} __packed tx;
> +	unsigned rx_len;
> +
> +	tx.port = pdata->port;
> +	tx.addr = addr;
> +	tx.mem_addr_len = 0;
> +	tx.mem_addr = 0;
> +	tx.buf_len = cpu_to_le16(data_len);
> +
> +	rx_len = sizeof(dln2->buf->rx);
> +
> +	ret = dln2_transfer(dln2->pdev, DLN2_I2C_READ, &tx, sizeof(tx),
> +			    &dln2->buf->rx, &rx_len);
> +	if (ret < 0)
> +		return ret;
> +	if (rx_len < sizeof(dln2->buf->rx.buf_len) + data_len)
> +		return -EPROTO;
> +	if (le16_to_cpu(dln2->buf->rx.buf_len) != data_len)
> +		return -EPROTO;
> +
> +	memcpy(data, dln2->buf->rx.buf, data_len);'

Use a temporary pointer to the rx struct above.

> +
> +	return data_len;
> +}

[...]

> +static DEVICE_ATTR_RW(dln2_i2c_freq);

Any new sysfs attribute must to be documented under Documentation/ABI.

[...]

> +static struct platform_driver dln2_i2c_driver = {
> +	.driver.name	= "dln2-i2c",
> +	.driver.owner	= THIS_MODULE,

No need to set the owner field when using the module_platform_driver
macro.

> +	.probe		= dln2_i2c_probe,
> +	.remove		= dln2_i2c_remove,
> +};
> +
> +module_platform_driver(dln2_i2c_driver);
> +
> +MODULE_AUTHOR("Laurentiu Palcu <laurentiu.palcu@intel.com>");
> +MODULE_DESCRIPTION("Driver for the Diolan DLN2 I2C master interface");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:dln2-i2c");

Johan
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 2ac87fa..6afc17e 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -1021,4 +1021,14 @@  config SCx200_ACB
 	  This support is also available as a module.  If so, the module
 	  will be called scx200_acb.
 
+config I2C_DLN2
+       tristate "Diolan DLN-2 USB I2C adapter"
+       depends on MFD_DLN2
+       help
+         If you say yes to this option, support will be included for Diolan
+         DLN2, a USB to I2C interface.
+
+         This driver can also be built as a module.  If so, the module
+         will be called i2c-dln2.
+
 endmenu
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 49bf07e..3118fea 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -100,5 +100,6 @@  obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o
 obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
 obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
 obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
+obj-$(CONFIG_I2C_DLN2)		+= i2c-dln2.o
 
 ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG
diff --git a/drivers/i2c/busses/i2c-dln2.c b/drivers/i2c/busses/i2c-dln2.c
new file mode 100644
index 0000000..21ad6dc
--- /dev/null
+++ b/drivers/i2c/busses/i2c-dln2.c
@@ -0,0 +1,383 @@ 
+/*
+ * Driver for the Diolan DLN-2 USB-I2C adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ *  i2c-diolan-u2c.c
+ *  Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_I2C_MODULE_ID		0x03
+#define DLN2_I2C_CMD(cmd)		DLN2_CMD(cmd, DLN2_I2C_MODULE_ID)
+
+/* I2C commands */
+#define DLN2_I2C_GET_PORT_COUNT		DLN2_I2C_CMD(0x00)
+#define DLN2_I2C_ENABLE			DLN2_I2C_CMD(0x01)
+#define DLN2_I2C_DISABLE		DLN2_I2C_CMD(0x02)
+#define DLN2_I2C_IS_ENABLED		DLN2_I2C_CMD(0x03)
+#define DLN2_I2C_SET_FREQUENCY		DLN2_I2C_CMD(0x04)
+#define DLN2_I2C_GET_FREQUENCY		DLN2_I2C_CMD(0x05)
+#define DLN2_I2C_WRITE			DLN2_I2C_CMD(0x06)
+#define DLN2_I2C_READ			DLN2_I2C_CMD(0x07)
+#define DLN2_I2C_SCAN_DEVICES		DLN2_I2C_CMD(0x08)
+#define DLN2_I2C_PULLUP_ENABLE		DLN2_I2C_CMD(0x09)
+#define DLN2_I2C_PULLUP_DISABLE		DLN2_I2C_CMD(0x0A)
+#define DLN2_I2C_PULLUP_IS_ENABLED	DLN2_I2C_CMD(0x0B)
+#define DLN2_I2C_TRANSFER		DLN2_I2C_CMD(0x0C)
+#define DLN2_I2C_SET_MAX_REPLY_COUNT	DLN2_I2C_CMD(0x0D)
+#define DLN2_I2C_GET_MAX_REPLY_COUNT	DLN2_I2C_CMD(0x0E)
+#define DLN2_I2C_GET_MIN_FREQUENCY	DLN2_I2C_CMD(0x40)
+#define DLN2_I2C_GET_MAX_FREQUENCY	DLN2_I2C_CMD(0x41)
+
+#define DLN2_I2C_FREQ_STD		100000
+
+#define DLN2_I2C_MAX_XFER_SIZE		256
+
+struct dln2_i2c {
+	struct platform_device *pdev;
+	struct i2c_adapter adapter;
+	u32 freq;
+	u32 min_freq;
+	u32 max_freq;
+	/*
+	 * Buffer to hold the packet for read or write transfers. One
+	 * is enough since we can't have multiple transfers in
+	 * parallel on the i2c adapter.
+	 */
+	union {
+		struct {
+			u8 port;
+			u8 addr;
+			u8 mem_addr_len;
+			__le32 mem_addr;
+			__le16 buf_len;
+			u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+		} __packed tx;
+		struct {
+			__le16 buf_len;
+			u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+		} __packed rx;
+	} *buf;
+};
+
+static int dln2_i2c_enable(struct dln2_i2c *dln2, bool enable)
+{
+	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
+	int ret;
+	u8 port;
+	u16 cmd;
+
+	port = pdata->port;
+
+	if (enable)
+		cmd = DLN2_I2C_ENABLE;
+	else
+		cmd = DLN2_I2C_DISABLE;
+
+	ret = dln2_transfer(dln2->pdev, cmd, &port, sizeof(port), NULL, NULL);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int dln2_i2c_set_frequency(struct dln2_i2c *dln2, u32 freq)
+{
+	int ret;
+	struct tx_data {
+		u8 port;
+		__le32 freq;
+	} __packed tx;
+	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
+
+	tx.port = pdata->port;
+	tx.freq = cpu_to_le32(freq);
+
+	ret = dln2_transfer(dln2->pdev, DLN2_I2C_SET_FREQUENCY, &tx, sizeof(tx),
+			    NULL, NULL);
+	if (ret < 0)
+		return ret;
+
+	dln2->freq = freq;
+
+	return 0;
+}
+
+static int dln2_i2c_get_freq(struct dln2_i2c *dln2, u16 cmd, u32 *res)
+{
+	int ret;
+	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
+	u8 port = pdata->port;
+	__le32 freq;
+	unsigned len = sizeof(freq);
+
+	ret = dln2_transfer(dln2->pdev, cmd, &port, sizeof(port),
+			    &freq, &len);
+	if (ret < 0)
+		return ret;
+	if (len < sizeof(freq))
+		return -EPROTO;
+
+	*res = le32_to_cpu(freq);
+
+	return 0;
+}
+
+static int dln2_i2c_setup(struct dln2_i2c *dln2)
+{
+	int ret;
+
+	ret = dln2_i2c_enable(dln2, false);
+	if (ret < 0)
+		return ret;
+
+	ret = dln2_i2c_get_freq(dln2, DLN2_I2C_GET_MIN_FREQUENCY,
+				&dln2->min_freq);
+	if (ret < 0)
+		return 0;
+
+	ret = dln2_i2c_get_freq(dln2, DLN2_I2C_GET_MAX_FREQUENCY,
+				&dln2->max_freq);
+	if (ret < 0)
+		return 0;
+
+	ret = dln2_i2c_set_frequency(dln2, DLN2_I2C_FREQ_STD);
+	if (ret < 0)
+		return ret;
+
+	ret = dln2_i2c_enable(dln2, true);
+
+	return ret;
+}
+
+static int dln2_i2c_write(struct dln2_i2c *dln2, u8 addr,
+			  u8 *data, u16 data_len)
+{
+	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
+	int ret;
+	unsigned len;
+
+	dln2->buf->tx.port = pdata->port;
+	dln2->buf->tx.addr = addr;
+	dln2->buf->tx.mem_addr_len = 0;
+	dln2->buf->tx.mem_addr = 0;
+	dln2->buf->tx.buf_len = cpu_to_le16(data_len);
+	memcpy(dln2->buf->tx.buf, data, data_len);
+
+	len = sizeof(dln2->buf->tx) + data_len - DLN2_I2C_MAX_XFER_SIZE;
+	ret = dln2_transfer(dln2->pdev, DLN2_I2C_WRITE, &dln2->buf->tx, len,
+			    NULL, NULL);
+	if (ret < 0)
+		return ret;
+
+	return data_len;
+}
+
+static int dln2_i2c_read(struct dln2_i2c *dln2, u16 addr, u8 *data,
+			 u16 data_len)
+{
+	struct dln2_platform_data *pdata = dev_get_platdata(&dln2->pdev->dev);
+	int ret;
+	struct {
+		u8 port;
+		u8 addr;
+		u8 mem_addr_len;
+		__le32 mem_addr;
+		__le16 buf_len;
+	} __packed tx;
+	unsigned rx_len;
+
+	tx.port = pdata->port;
+	tx.addr = addr;
+	tx.mem_addr_len = 0;
+	tx.mem_addr = 0;
+	tx.buf_len = cpu_to_le16(data_len);
+
+	rx_len = sizeof(dln2->buf->rx);
+
+	ret = dln2_transfer(dln2->pdev, DLN2_I2C_READ, &tx, sizeof(tx),
+			    &dln2->buf->rx, &rx_len);
+	if (ret < 0)
+		return ret;
+	if (rx_len < sizeof(dln2->buf->rx.buf_len) + data_len)
+		return -EPROTO;
+	if (le16_to_cpu(dln2->buf->rx.buf_len) != data_len)
+		return -EPROTO;
+
+	memcpy(data, dln2->buf->rx.buf, data_len);
+
+	return data_len;
+}
+
+static int dln2_i2c_xfer(struct i2c_adapter *adapter,
+			 struct i2c_msg *msgs, int num)
+{
+	struct dln2_i2c *dln2 = i2c_get_adapdata(adapter);
+	struct i2c_msg *pmsg;
+	int i;
+
+	for (i = 0; i < num; i++) {
+		int ret;
+
+		pmsg = &msgs[i];
+
+		if (pmsg->len > DLN2_I2C_MAX_XFER_SIZE)
+			return -EINVAL;
+
+		if (pmsg->flags & I2C_M_RD) {
+			ret = dln2_i2c_read(dln2, pmsg->addr, pmsg->buf,
+					    pmsg->len);
+			if (ret < 0)
+				return ret;
+
+			pmsg->len = ret;
+		} else {
+			ret = dln2_i2c_write(dln2, pmsg->addr, pmsg->buf,
+					     pmsg->len);
+			if (ret != pmsg->len)
+				return -EPROTO;
+		}
+	}
+
+	return num;
+}
+
+static u32 dln2_i2c_func(struct i2c_adapter *a)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_BYTE_DATA |
+		I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
+		I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static const struct i2c_algorithm dln2_i2c_usb_algorithm = {
+	.master_xfer = dln2_i2c_xfer,
+	.functionality = dln2_i2c_func,
+};
+
+static ssize_t dln2_i2c_freq_show(struct device *dev,
+				  struct device_attribute *attr, char *buf)
+{
+	struct dln2_i2c *dln2 = dev_get_drvdata(dev);
+
+	return snprintf(buf, PAGE_SIZE, "%d\n", dln2->freq);
+}
+
+static ssize_t dln2_i2c_freq_store(struct device *dev,
+				   struct device_attribute *attr,
+				   const char *buf, size_t count)
+{
+	struct dln2_i2c *dln2 = dev_get_drvdata(dev);
+	unsigned long freq;
+	int ret;
+
+	if (kstrtoul(buf, 0, &freq) || freq < dln2->min_freq ||
+	    freq > dln2->max_freq)
+		return -EINVAL;
+
+	ret = dln2_i2c_enable(dln2, false);
+	if (ret < 0)
+		return ret;
+
+	ret = dln2_i2c_set_frequency(dln2, freq);
+	if (ret < 0)
+		return ret;
+
+	ret = dln2_i2c_enable(dln2, true);
+
+	return count;
+}
+
+static DEVICE_ATTR_RW(dln2_i2c_freq);
+static struct attribute *dln2_i2c_freq_attrs[] = {
+	&dev_attr_dln2_i2c_freq.attr,
+	NULL
+};
+ATTRIBUTE_GROUPS(dln2_i2c_freq);
+
+static int dln2_i2c_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct dln2_i2c *dln2;
+	struct device *dev = &pdev->dev;
+	struct dln2_platform_data *pdata = dev_get_platdata(&pdev->dev);
+
+	dln2 = devm_kzalloc(dev, sizeof(*dln2), GFP_KERNEL);
+	if (!dln2)
+		return -ENOMEM;
+
+	dln2->buf = devm_kmalloc(dev, sizeof(*dln2->buf), GFP_KERNEL);
+	if (!dln2->buf)
+		return -ENOMEM;
+
+	dln2->pdev = pdev;
+
+	/* setup i2c adapter description */
+	dln2->adapter.owner = THIS_MODULE;
+	dln2->adapter.class = I2C_CLASS_HWMON;
+	dln2->adapter.algo = &dln2_i2c_usb_algorithm;
+	dln2->adapter.dev.parent = dev;
+	dln2->adapter.dev.groups = dln2_i2c_freq_groups;
+	i2c_set_adapdata(&dln2->adapter, dln2);
+	snprintf(dln2->adapter.name, sizeof(dln2->adapter.name), "%s-%s-%d",
+		 "dln2-i2c", dev_name(pdev->dev.parent), pdata->port);
+
+	platform_set_drvdata(pdev, dln2);
+
+	/* initialize the i2c interface */
+	ret = dln2_i2c_setup(dln2);
+	if (ret < 0) {
+		dev_err(dev, "failed to initialize adapter: %d\n", ret);
+		return ret;
+	}
+
+	/* and finally attach to i2c layer */
+	ret = i2c_add_adapter(&dln2->adapter);
+	if (ret < 0) {
+		dev_err(dev, "failed to add I2C adapter: %d\n", ret);
+		goto out_disable;
+	}
+
+	return 0;
+
+out_disable:
+	dln2_i2c_enable(dln2, false);
+
+	return ret;
+}
+
+static int dln2_i2c_remove(struct platform_device *pdev)
+{
+	struct dln2_i2c *dln2 = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&dln2->adapter);
+	dln2_i2c_enable(dln2, false);
+
+	return 0;
+}
+
+static struct platform_driver dln2_i2c_driver = {
+	.driver.name	= "dln2-i2c",
+	.driver.owner	= THIS_MODULE,
+	.probe		= dln2_i2c_probe,
+	.remove		= dln2_i2c_remove,
+};
+
+module_platform_driver(dln2_i2c_driver);
+
+MODULE_AUTHOR("Laurentiu Palcu <laurentiu.palcu@intel.com>");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 I2C master interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-i2c");