| Message ID | 1442996938-47147-1-git-send-email-hongtao.jia@freescale.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Delegated to: | Scott Wood |
| Headers | show |
On Wed, 2015-09-23 at 16:28 +0800, Jia Hongtao wrote: > This driver add thermal management support by enabling TMU (Thermal > Monitoring Unit) on QorIQ platform. > > It's based on thermal of framework: > - Trip points defined in device tree. > - Cpufreq as cooling device registered in qoriq cpufreq driver. I don't see any cooling device registered in the qoriq cpufreq driver. Is this dependent on some other patch? > > Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com> > --- > V3: Using thermal of framework. > > drivers/thermal/Kconfig | 11 ++ > drivers/thermal/Makefile | 1 + > drivers/thermal/qoriq_thermal.c | 267 > ++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 279 insertions(+) > create mode 100644 drivers/thermal/qoriq_thermal.c > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > index 0390044..c91041b 100644 > --- a/drivers/thermal/Kconfig > +++ b/drivers/thermal/Kconfig > @@ -180,6 +180,17 @@ config IMX_THERMAL > cpufreq is used as the cooling device to throttle CPUs when the > passive trip is crossed. > > +config QORIQ_THERMAL > + tristate "Freescale QorIQ Thermal Monitoring Unit" > + depends on CPU_THERMAL > + depends on THERMAL_OF > + default n > + help > + Enable thermal management based on Freescale QorIQ Thermal Monitoring > + Unit (TMU). It supports one critical trip point and one passive trip > + point. The cpufreq is used as the cooling device to throttle CPUs when > + the passive trip is crossed. "default n" is unnecessary -- n is already the default. Where is the interaction between this driver and cpufreq? > config SPEAR_THERMAL > bool "SPEAr thermal sensor driver" > depends on PLAT_SPEAR > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > index 26f1608..e55d703 100644 > --- a/drivers/thermal/Makefile > +++ b/drivers/thermal/Makefile > @@ -33,6 +33,7 @@ obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o > obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o > obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o > obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o > +obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o > obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o > obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o > obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o > diff --git a/drivers/thermal/qoriq_thermal.c > b/drivers/thermal/qoriq_thermal.c > new file mode 100644 > index 0000000..7c2a3261 > --- /dev/null > +++ b/drivers/thermal/qoriq_thermal.c > @@ -0,0 +1,267 @@ > +/* > + * Copyright 2015 Freescale Semiconductor, Inc. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms and conditions of the GNU General Public License, > + * version 2, as published by the Free Software Foundation. > + * > + * This program is distributed in the hope it will be useful, but WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License > for > + * more details. > + * > + */ > + > +/* > + * Based on Freescale QorIQ Thermal Monitoring Unit (TMU) > + */ What does this comment mean? This *is* the "Freescale QorIQ Thermal Monitoring Unit" driver. > +#include <linux/cpufreq.h> What do you use from this header? > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/err.h> > +#include <linux/io.h> > +#include <linux/of.h> > +#include <linux/of_address.h> > +#include <linux/thermal.h> > + > +#include "thermal_core.h" > + > +#define SITES_MAX 16 > + > +/* > + * QorIQ TMU Registers > + */ > +struct qoriq_tmu_site_regs { > + __be32 tritsr; /* Immediate Temperature Site Register */ > + __be32 tratsr; /* Average Temperature Site Register */ > + u8 res0[0x8]; > +} __packed; > + > +struct qoriq_tmu_regs { > + __be32 tmr; /* Mode Register */ > +#define TMR_DISABLE 0x0 > +#define TMR_ME 0x80000000 > +#define TMR_ALPF 0x0c000000 > +#define TMR_MSITE 0x00008000 /* Core temperature site */ > +#define TMR_ALL (TMR_ME | TMR_ALPF | TMR_MSITE) > + __be32 tsr; /* Status Register */ > + __be32 tmtmir; /* Temperature measurement interval Register */ > +#define TMTMIR_DEFAULT 0x00000007 > + u8 res0[0x14]; > + __be32 tier; /* Interrupt Enable Register */ > +#define TIER_DISABLE 0x0 > + __be32 tidr; /* Interrupt Detect Register */ > + __be32 tiscr; /* Interrupt Site Capture Register */ > + __be32 ticscr; /* Interrupt Critical Site Capture Register */ > + u8 res1[0x10]; > + __be32 tmhtcrh; /* High Temperature Capture Register */ > + __be32 tmhtcrl; /* Low Temperature Capture Register */ > + u8 res2[0x8]; > + __be32 tmhtitr; /* High Temperature Immediate Threshold */ > + __be32 tmhtatr; /* High Temperature Average Threshold */ > + __be32 tmhtactr; /* High Temperature Average Crit Threshold */ > + u8 res3[0x24]; > + __be32 ttcfgr; /* Temperature Configuration Register */ > + __be32 tscfgr; /* Sensor Configuration Register */ > + u8 res4[0x78]; > + struct qoriq_tmu_site_regs site[SITES_MAX]; > + u8 res5[0x9f8]; > + __be32 ipbrr0; /* IP Block Revision Register 0 */ > + __be32 ipbrr1; /* IP Block Revision Register 1 */ > + u8 res6[0x310]; > + __be32 ttr0cr; /* Temperature Range 0 Control Register */ > + __be32 ttr1cr; /* Temperature Range 1 Control Register */ > + __be32 ttr2cr; /* Temperature Range 2 Control Register */ > + __be32 ttr3cr; /* Temperature Range 3 Control Register */ > +}; > + > +/* > + * Thermal zone data > + */ > +struct qoriq_tmu_data { > + struct thermal_zone_device *tz; > + struct qoriq_tmu_regs __iomem *regs; > +}; > + > +static int tmu_get_temp(void *p, int *temp) > +{ > + u8 val; > + struct qoriq_tmu_data *data = p; > + > + val = ioread32be(&data->regs->site[0].tritsr); > + *temp = (int)val * 1000; Why don't you declare val as int in the first place? > + for (i = 0; i < len; i += 8, calibration += 2) { > + val = (int)of_read_number(calibration, 1); > + iowrite32be(val, &data->regs->ttcfgr); > + val = (int)of_read_number(calibration + 1, 1); > + iowrite32be(val, &data->regs->tscfgr); Unnecessary casts. > + } > + > + return 0; > +} > + > +static void qoriq_tmu_init_device(struct qoriq_tmu_data *data) > +{ > + /* Disable interrupt, using polling instead */ > + iowrite32be(TIER_DISABLE, &data->regs->tier); > + > + /* Set update_interval */ > + iowrite32be(TMTMIR_DEFAULT, &data->regs->tmtmir); > + > + /* Enable monitoring */ > + iowrite32be(TMR_ALL, &data->regs->tmr); > +} > + > +static struct thermal_zone_of_device_ops tmu_tz_ops = { > + .get_temp = tmu_get_temp, > +}; > + > +static int qoriq_tmu_probe(struct platform_device *pdev) > +{ > + int ret; > + const struct thermal_trip *trip; > + struct qoriq_tmu_data *data; > + > + if (!pdev->dev.of_node) { > + dev_err(&pdev->dev, "Device OF-Node is NULL"); > + return -EFAULT; > + } EFAULT is for bad user addresses and is not appropriate here. > + > + data = devm_kzalloc(&pdev->dev, sizeof(struct qoriq_tmu_data), > + GFP_KERNEL); > + if (!data) > + return -ENOMEM; > + > + platform_set_drvdata(pdev, data); > + data->regs = of_iomap(pdev->dev.of_node, 0); > + > + if (!data->regs) { > + dev_err(&pdev->dev, "Failed to get memory region\n"); > + ret = -ENODEV; > + goto err_iomap; > + } > + > + ret = qoriq_tmu_calibration(pdev); /* TMU calibration */ > + if (ret < 0) { > + dev_err(&pdev->dev, "TMU calibration failed.\n"); > + ret = -ENODEV; > + goto err_iomap; > + } That function returns negative when device tree properties are missing, not when a calibration procedure fails. > + > + qoriq_tmu_init_device(data); /* TMU initialization */ > + > + data->tz = thermal_zone_of_sensor_register(&pdev->dev, 0, > + data, &tmu_tz_ops); > + if (IS_ERR(data->tz)) { > + ret = PTR_ERR(data->tz); > + dev_err(&pdev->dev, > + "Failed to register thermal zone device %d\n", ret); > + goto err_thermal; > + } > + > + trip = of_thermal_get_trip_points(data->tz); > + > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); Doesn't thermal_zone_of_sensor_register() already call ops->set_mode with TERMAL_DEVICE_ENABLED? > + > + return 0; > + > +err_thermal: > + iounmap(data->regs); > + > +err_iomap: > + platform_set_drvdata(pdev, NULL); > + devm_kfree(&pdev->dev, data); > + > + return ret; > +} > + > +static int qoriq_tmu_remove(struct platform_device *pdev) > +{ > + struct qoriq_tmu_data *data = platform_get_drvdata(pdev); > + > + /* Disable monitoring */ > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > + > + thermal_zone_of_sensor_unregister(&pdev->dev, data->tz); > + iounmap(data->regs); > + > + platform_set_drvdata(pdev, NULL); > + devm_kfree(&pdev->dev, data); > + > + return 0; > +} > + > +#ifdef CONFIG_PM_SLEEP > +static int qoriq_tmu_suspend(struct device *dev) > +{ > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > + > + /* Disable monitoring */ > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_DISABLED); > + > + return 0; > +} > + > +static int qoriq_tmu_resume(struct device *dev) > +{ > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > + > + /* Enable monitoring */ > + iowrite32be(TMR_ALL, &data->regs->tmr); > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); > + > + return 0; > +} > +#endif > + > +static SIMPLE_DEV_PM_OPS(qoriq_tmu_pm_ops, > + qoriq_tmu_suspend, qoriq_tmu_resume); > + > +static const struct of_device_id qoriq_tmu_match[] = { > + { .compatible = "fsl,qoriq-tmu", }, > + {}, > +}; Binding? > + > +static struct platform_driver qoriq_tmu = { > + .driver = { > + .name = "qoriq_thermal", > + .pm = &qoriq_tmu_pm_ops, > + .of_match_table = qoriq_tmu_match, > + }, Why the tabs after ".name"? -Scott
> -----Original Message----- > From: Wood Scott-B07421 > Sent: Friday, September 25, 2015 6:10 AM > To: Jia Hongtao-B38951 > Cc: edubezval@gmail.com; linux-pm@vger.kernel.org; linuxppc- > dev@lists.ozlabs.org > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management support > > On Wed, 2015-09-23 at 16:28 +0800, Jia Hongtao wrote: > > This driver add thermal management support by enabling TMU (Thermal > > Monitoring Unit) on QorIQ platform. > > > > It's based on thermal of framework: > > - Trip points defined in device tree. > > - Cpufreq as cooling device registered in qoriq cpufreq driver. > > I don't see any cooling device registered in the qoriq cpufreq driver. > Is this dependent on some other patch? It's not depend on any patch. But I saw your patch below: [PATCH v3 5/5] cpufreq: qoriq: Don't look at clock implementation details So I hold my patch waiting for your patch merged or there will be conflict. I could send it out too if you are fine with it. > > > > > Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com> > > --- > > V3: Using thermal of framework. > > > > drivers/thermal/Kconfig | 11 ++ > > drivers/thermal/Makefile | 1 + > > drivers/thermal/qoriq_thermal.c | 267 > > ++++++++++++++++++++++++++++++++++++++++ > > 3 files changed, 279 insertions(+) > > create mode 100644 drivers/thermal/qoriq_thermal.c > > > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index > > 0390044..c91041b 100644 > > --- a/drivers/thermal/Kconfig > > +++ b/drivers/thermal/Kconfig > > @@ -180,6 +180,17 @@ config IMX_THERMAL > > cpufreq is used as the cooling device to throttle CPUs when the > > passive trip is crossed. > > > > +config QORIQ_THERMAL > > + tristate "Freescale QorIQ Thermal Monitoring Unit" > > + depends on CPU_THERMAL > > + depends on THERMAL_OF > > + default n > > + help > > + Enable thermal management based on Freescale QorIQ Thermal > Monitoring > > + Unit (TMU). It supports one critical trip point and one passive > trip > > + point. The cpufreq is used as the cooling device to throttle > CPUs when > > + the passive trip is crossed. > > "default n" is unnecessary -- n is already the default. Right. > > Where is the interaction between this driver and cpufreq? It's all in cpufreq patch I mentioned above. > > > config SPEAR_THERMAL > > bool "SPEAr thermal sensor driver" > > depends on PLAT_SPEAR > > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index > > 26f1608..e55d703 100644 > > --- a/drivers/thermal/Makefile > > +++ b/drivers/thermal/Makefile > > @@ -33,6 +33,7 @@ obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o > > obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o > > obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o > > obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o > > +obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o > > obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o > > obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o > > obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o > > diff --git a/drivers/thermal/qoriq_thermal.c > > b/drivers/thermal/qoriq_thermal.c new file mode 100644 index > > 0000000..7c2a3261 > > --- /dev/null > > +++ b/drivers/thermal/qoriq_thermal.c > > @@ -0,0 +1,267 @@ > > +/* > > + * Copyright 2015 Freescale Semiconductor, Inc. > > + * > > + * This program is free software; you can redistribute it and/or > > +modify it > > + * under the terms and conditions of the GNU General Public License, > > + * version 2, as published by the Free Software Foundation. > > + * > > + * This program is distributed in the hope it will be useful, but > > +WITHOUT > > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY > > +or > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public > > +License > > for > > + * more details. > > + * > > + */ > > + > > +/* > > + * Based on Freescale QorIQ Thermal Monitoring Unit (TMU) */ > > What does this comment mean? This *is* the "Freescale QorIQ Thermal > Monitoring Unit" driver. I mean thermal management based on the monitor TMU. I could remove this comment though. > > > +#include <linux/cpufreq.h> > > What do you use from this header? Sorry, forget to remove it from last version in which cooling devices are registered in thermal driver instead of cpufreq driver. > > > +#include <linux/module.h> > > +#include <linux/platform_device.h> > > +#include <linux/err.h> > > +#include <linux/io.h> > > +#include <linux/of.h> > > +#include <linux/of_address.h> > > +#include <linux/thermal.h> > > + > > +#include "thermal_core.h" > > + > > +#define SITES_MAX 16 > > + > > +/* > > + * QorIQ TMU Registers > > + */ > > +struct qoriq_tmu_site_regs { > > + __be32 tritsr; /* Immediate Temperature Site Register */ > > + __be32 tratsr; /* Average Temperature Site Register */ > > + u8 res0[0x8]; > > +} __packed; > > + > > +struct qoriq_tmu_regs { > > + __be32 tmr; /* Mode Register */ > > +#define TMR_DISABLE 0x0 > > +#define TMR_ME 0x80000000 > > +#define TMR_ALPF 0x0c000000 > > +#define TMR_MSITE 0x00008000 /* Core temperature site */ > > +#define TMR_ALL (TMR_ME | TMR_ALPF | TMR_MSITE) > > + __be32 tsr; /* Status Register */ > > + __be32 tmtmir; /* Temperature measurement interval > Register */ > > +#define TMTMIR_DEFAULT 0x00000007 > > + u8 res0[0x14]; > > + __be32 tier; /* Interrupt Enable Register */ > > +#define TIER_DISABLE 0x0 > > + __be32 tidr; /* Interrupt Detect Register */ > > + __be32 tiscr; /* Interrupt Site Capture Register */ > > + __be32 ticscr; /* Interrupt Critical Site Capture > Register */ > > + u8 res1[0x10]; > > + __be32 tmhtcrh; /* High Temperature Capture Register */ > > + __be32 tmhtcrl; /* Low Temperature Capture Register */ > > + u8 res2[0x8]; > > + __be32 tmhtitr; /* High Temperature Immediate Threshold > */ > > + __be32 tmhtatr; /* High Temperature Average Threshold */ > > + __be32 tmhtactr; /* High Temperature Average Crit > Threshold */ > > + u8 res3[0x24]; > > + __be32 ttcfgr; /* Temperature Configuration Register */ > > + __be32 tscfgr; /* Sensor Configuration Register */ > > + u8 res4[0x78]; > > + struct qoriq_tmu_site_regs site[SITES_MAX]; > > + u8 res5[0x9f8]; > > + __be32 ipbrr0; /* IP Block Revision Register 0 */ > > + __be32 ipbrr1; /* IP Block Revision Register 1 */ > > + u8 res6[0x310]; > > + __be32 ttr0cr; /* Temperature Range 0 Control Register > */ > > + __be32 ttr1cr; /* Temperature Range 1 Control Register > */ > > + __be32 ttr2cr; /* Temperature Range 2 Control Register > */ > > + __be32 ttr3cr; /* Temperature Range 3 Control Register > */ > > +}; > > + > > +/* > > + * Thermal zone data > > + */ > > +struct qoriq_tmu_data { > > + struct thermal_zone_device *tz; > > + struct qoriq_tmu_regs __iomem *regs; }; > > + > > > +static int tmu_get_temp(void *p, int *temp) { > > + u8 val; > > + struct qoriq_tmu_data *data = p; > > + > > + val = ioread32be(&data->regs->site[0].tritsr); > > + *temp = (int)val * 1000; > > Why don't you declare val as int in the first place? It's a 32bit register. Only the least significant 8 bits represent the temperature. The most significant bit shows the validness of the value. I use u8 type to remove the rest 24bits influence. > > > + for (i = 0; i < len; i += 8, calibration += 2) { > > + val = (int)of_read_number(calibration, 1); > > + iowrite32be(val, &data->regs->ttcfgr); > > + val = (int)of_read_number(calibration + 1, 1); > > + iowrite32be(val, &data->regs->tscfgr); > > Unnecessary casts. Ok. > > > + } > > + > > + return 0; > > +} > > + > > +static void qoriq_tmu_init_device(struct qoriq_tmu_data *data) { > > + /* Disable interrupt, using polling instead */ > > + iowrite32be(TIER_DISABLE, &data->regs->tier); > > + > > + /* Set update_interval */ > > + iowrite32be(TMTMIR_DEFAULT, &data->regs->tmtmir); > > + > > + /* Enable monitoring */ > > + iowrite32be(TMR_ALL, &data->regs->tmr); } > > + > > +static struct thermal_zone_of_device_ops tmu_tz_ops = { > > + .get_temp = tmu_get_temp, > > +}; > > + > > +static int qoriq_tmu_probe(struct platform_device *pdev) { > > + int ret; > > + const struct thermal_trip *trip; > > + struct qoriq_tmu_data *data; > > + > > + if (!pdev->dev.of_node) { > > + dev_err(&pdev->dev, "Device OF-Node is NULL"); > > + return -EFAULT; > > + } > > EFAULT is for bad user addresses and is not appropriate here. I will change it to ENODEV. > > > + > > + data = devm_kzalloc(&pdev->dev, sizeof(struct qoriq_tmu_data), > > + GFP_KERNEL); > > + if (!data) > > + return -ENOMEM; > > + > > + platform_set_drvdata(pdev, data); > > + data->regs = of_iomap(pdev->dev.of_node, 0); > > + > > + if (!data->regs) { > > + dev_err(&pdev->dev, "Failed to get memory region\n"); > > + ret = -ENODEV; > > + goto err_iomap; > > + } > > + > > + ret = qoriq_tmu_calibration(pdev); /* TMU calibration */ > > + if (ret < 0) { > > + dev_err(&pdev->dev, "TMU calibration failed.\n"); > > + ret = -ENODEV; > > + goto err_iomap; > > + } > > That function returns negative when device tree properties are missing, > not when a calibration procedure fails. What's your suggestion here to return then? > > > + > > + qoriq_tmu_init_device(data); /* TMU initialization */ > > + > > + data->tz = thermal_zone_of_sensor_register(&pdev->dev, 0, > > + data, &tmu_tz_ops); > > + if (IS_ERR(data->tz)) { > > + ret = PTR_ERR(data->tz); > > + dev_err(&pdev->dev, > > + "Failed to register thermal zone device %d\n", > ret); > > + goto err_thermal; > > + } > > + > > + trip = of_thermal_get_trip_points(data->tz); > > + > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); > > Doesn't thermal_zone_of_sensor_register() already call ops->set_mode with > TERMAL_DEVICE_ENABLED? You are right. I referenced the code from other platform and did not notice this. Thanks. > > > + > > + return 0; > > + > > +err_thermal: > > + iounmap(data->regs); > > + > > +err_iomap: > > + platform_set_drvdata(pdev, NULL); > > + devm_kfree(&pdev->dev, data); > > + > > + return ret; > > +} > > + > > +static int qoriq_tmu_remove(struct platform_device *pdev) { > > + struct qoriq_tmu_data *data = platform_get_drvdata(pdev); > > + > > + /* Disable monitoring */ > > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > > + > > + thermal_zone_of_sensor_unregister(&pdev->dev, data->tz); > > + iounmap(data->regs); > > + > > + platform_set_drvdata(pdev, NULL); > > + devm_kfree(&pdev->dev, data); > > + > > + return 0; > > +} > > + > > +#ifdef CONFIG_PM_SLEEP > > +static int qoriq_tmu_suspend(struct device *dev) { > > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > > + > > + /* Disable monitoring */ > > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_DISABLED); > > + > > + return 0; > > +} > > + > > +static int qoriq_tmu_resume(struct device *dev) { > > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > > + > > + /* Enable monitoring */ > > + iowrite32be(TMR_ALL, &data->regs->tmr); > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); > > + > > + return 0; > > +} > > +#endif > > + > > +static SIMPLE_DEV_PM_OPS(qoriq_tmu_pm_ops, > > + qoriq_tmu_suspend, qoriq_tmu_resume); > > + > > > > +static const struct of_device_id qoriq_tmu_match[] = { > > + { .compatible = "fsl,qoriq-tmu", }, > > + {}, > > +}; > > Binding? Not send out yet. I planned to send the patch with device tree patchset including adding TMU node to T1040/T1024/LS1021A platform. It's depending on the device tree files moving patch I sent out not long ago. > > > + > > +static struct platform_driver qoriq_tmu = { > > + .driver = { > > + .name = "qoriq_thermal", > > + .pm = &qoriq_tmu_pm_ops, > > + .of_match_table = qoriq_tmu_match, > > + }, > > Why the tabs after ".name"? Will indent the other two. > > -Scott
On Thu, 2015-09-24 at 22:09 -0500, Jia Hongtao-B38951 wrote: > > -----Original Message----- > > From: Wood Scott-B07421 > > Sent: Friday, September 25, 2015 6:10 AM > > To: Jia Hongtao-B38951 > > Cc: edubezval@gmail.com; linux-pm@vger.kernel.org; linuxppc- > > dev@lists.ozlabs.org > > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management support > > > > On Wed, 2015-09-23 at 16:28 +0800, Jia Hongtao wrote: > > > This driver add thermal management support by enabling TMU (Thermal > > > Monitoring Unit) on QorIQ platform. > > > > > > It's based on thermal of framework: > > > - Trip points defined in device tree. > > > - Cpufreq as cooling device registered in qoriq cpufreq driver. > > > > I don't see any cooling device registered in the qoriq cpufreq driver. > > Is this dependent on some other patch? > > It's not depend on any patch. But I saw your patch below: > [PATCH v3 5/5] cpufreq: qoriq: Don't look at clock implementation details > So I hold my patch waiting for your patch merged or there will be conflict. > > I could send it out too if you are fine with it. Yes, rebase it on that patch and send it. Mention below the --- that you're depending on that patch, and provide a patchwork/archive link. > > > +static int tmu_get_temp(void *p, int *temp) { > > > + u8 val; > > > + struct qoriq_tmu_data *data = p; > > > + > > > + val = ioread32be(&data->regs->site[0].tritsr); > > > + *temp = (int)val * 1000; > > > > Why don't you declare val as int in the first place? > > It's a 32bit register. > Only the least significant 8 bits represent the temperature. > The most significant bit shows the validness of the value. > I use u8 type to remove the rest 24bits influence. That's even worse. Use an explicit & operation to extract the field you're interested in. > > > + ret = qoriq_tmu_calibration(pdev); /* TMU calibration */ > > > + if (ret < 0) { > > > + dev_err(&pdev->dev, "TMU calibration failed.\n"); > > > + ret = -ENODEV; > > > + goto err_iomap; > > > + } > > > > That function returns negative when device tree properties are missing, > > not when a calibration procedure fails. > > What's your suggestion here to return then? Remove this message and add a message in qoriq_tmu_calibration for each error condition. Also have qoriq_tmu_calibration pass back a proper error code, not -1. > > > +static const struct of_device_id qoriq_tmu_match[] = { > > > + { .compatible = "fsl,qoriq-tmu", }, > > > + {}, > > > +}; > > > > Binding? > > Not send out yet. The binding needs to come before the driver that uses it. -Scott
> -----Original Message----- > From: Wood Scott-B07421 > Sent: Friday, September 25, 2015 1:12 PM > To: Jia Hongtao-B38951 > Cc: edubezval@gmail.com; linux-pm@vger.kernel.org; linuxppc- > dev@lists.ozlabs.org > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management support > > On Thu, 2015-09-24 at 22:09 -0500, Jia Hongtao-B38951 wrote: > > > -----Original Message----- > > > From: Wood Scott-B07421 > > > Sent: Friday, September 25, 2015 6:10 AM > > > To: Jia Hongtao-B38951 > > > Cc: edubezval@gmail.com; linux-pm@vger.kernel.org; linuxppc- > > > dev@lists.ozlabs.org > > > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management > support > > > > > > On Wed, 2015-09-23 at 16:28 +0800, Jia Hongtao wrote: > > > > This driver add thermal management support by enabling TMU (Thermal > > > > Monitoring Unit) on QorIQ platform. > > > > > > > > It's based on thermal of framework: > > > > - Trip points defined in device tree. > > > > - Cpufreq as cooling device registered in qoriq cpufreq driver. > > > > > > I don't see any cooling device registered in the qoriq cpufreq driver. > > > Is this dependent on some other patch? > > > > It's not depend on any patch. But I saw your patch below: > > [PATCH v3 5/5] cpufreq: qoriq: Don't look at clock implementation > details > > So I hold my patch waiting for your patch merged or there will be > conflict. > > > > I could send it out too if you are fine with it. > > Yes, rebase it on that patch and send it. Mention below the --- that > you're > depending on that patch, and provide a patchwork/archive link. Ok. But I need rebase again if you have further changes on that patch. Anyway, this is not a big problem for me. > > > > > +static int tmu_get_temp(void *p, int *temp) { > > > > + u8 val; > > > > + struct qoriq_tmu_data *data = p; > > > > + > > > > + val = ioread32be(&data->regs->site[0].tritsr); > > > > + *temp = (int)val * 1000; > > > > > > Why don't you declare val as int in the first place? > > > > It's a 32bit register. > > Only the least significant 8 bits represent the temperature. > > The most significant bit shows the validness of the value. > > I use u8 type to remove the rest 24bits influence. > > That's even worse. Use an explicit & operation to extract the field > you're > interested in. Will change for next version. > > > > > + ret = qoriq_tmu_calibration(pdev); /* TMU calibration */ > > > > + if (ret < 0) { > > > > + dev_err(&pdev->dev, "TMU calibration failed.\n"); > > > > + ret = -ENODEV; > > > > + goto err_iomap; > > > > + } > > > > > > That function returns negative when device tree properties are > missing, > > > not when a calibration procedure fails. > > > > What's your suggestion here to return then? > > Remove this message and add a message in qoriq_tmu_calibration for each > error > condition. Also have qoriq_tmu_calibration pass back a proper error code, > not -1. Yes, this is more reasonable. > > > > > +static const struct of_device_id qoriq_tmu_match[] = { > > > > + { .compatible = "fsl,qoriq-tmu", }, > > > > + {}, > > > > +}; > > > > > > Binding? > > > > Not send out yet. > > The binding needs to come before the driver that uses it. Right. I will send out the whole patchset. > > -Scott >
On Fri, Sep 25, 2015 at 03:09:42AM +0000, Hongtao Jia wrote: > > > -----Original Message----- > > From: Wood Scott-B07421 > > Sent: Friday, September 25, 2015 6:10 AM > > To: Jia Hongtao-B38951 > > Cc: edubezval@gmail.com; linux-pm@vger.kernel.org; linuxppc- > > dev@lists.ozlabs.org > > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management support > > > > On Wed, 2015-09-23 at 16:28 +0800, Jia Hongtao wrote: > > > This driver add thermal management support by enabling TMU (Thermal > > > Monitoring Unit) on QorIQ platform. > > > > > > It's based on thermal of framework: > > > - Trip points defined in device tree. > > > - Cpufreq as cooling device registered in qoriq cpufreq driver. > > > > I don't see any cooling device registered in the qoriq cpufreq driver. > > Is this dependent on some other patch? > > It's not depend on any patch. But I saw your patch below: > [PATCH v3 5/5] cpufreq: qoriq: Don't look at clock implementation details > So I hold my patch waiting for your patch merged or there will be conflict. > > I could send it out too if you are fine with it. Would you guys benefit of cpufreq-cpu0? > > > > > > > > > Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com> > > > --- > > > V3: Using thermal of framework. > > > > > > drivers/thermal/Kconfig | 11 ++ > > > drivers/thermal/Makefile | 1 + > > > drivers/thermal/qoriq_thermal.c | 267 Please include a binding description in your next version. Also, remember to include an example of your binding. > > > ++++++++++++++++++++++++++++++++++++++++ > > > 3 files changed, 279 insertions(+) > > > create mode 100644 drivers/thermal/qoriq_thermal.c > > > > > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index > > > 0390044..c91041b 100644 > > > --- a/drivers/thermal/Kconfig > > > +++ b/drivers/thermal/Kconfig > > > @@ -180,6 +180,17 @@ config IMX_THERMAL > > > cpufreq is used as the cooling device to throttle CPUs when the > > > passive trip is crossed. > > > > > > +config QORIQ_THERMAL It would be really great if you could consolidate this driver with IMX_THERMAL. Do you think it is doable? > > > + tristate "Freescale QorIQ Thermal Monitoring Unit" > > > + depends on CPU_THERMAL > > > + depends on THERMAL_OF > > > + default n > > > + help > > > + Enable thermal management based on Freescale QorIQ Thermal > > Monitoring > > > + Unit (TMU). It supports one critical trip point and one passive > > trip > > > + point. The cpufreq is used as the cooling device to throttle > > CPUs when > > > + the passive trip is crossed. > > > > "default n" is unnecessary -- n is already the default. > > Right. > > > > > Where is the interaction between this driver and cpufreq? > > It's all in cpufreq patch I mentioned above. > > > > > > config SPEAR_THERMAL > > > bool "SPEAr thermal sensor driver" > > > depends on PLAT_SPEAR > > > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index > > > 26f1608..e55d703 100644 > > > --- a/drivers/thermal/Makefile > > > +++ b/drivers/thermal/Makefile > > > @@ -33,6 +33,7 @@ obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o > > > obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o > > > obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o > > > obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o > > > +obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o > > > obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o > > > obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o > > > obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o > > > diff --git a/drivers/thermal/qoriq_thermal.c > > > b/drivers/thermal/qoriq_thermal.c new file mode 100644 index > > > 0000000..7c2a3261 > > > --- /dev/null > > > +++ b/drivers/thermal/qoriq_thermal.c > > > @@ -0,0 +1,267 @@ > > > +/* > > > + * Copyright 2015 Freescale Semiconductor, Inc. > > > + * > > > + * This program is free software; you can redistribute it and/or > > > +modify it > > > + * under the terms and conditions of the GNU General Public License, > > > + * version 2, as published by the Free Software Foundation. > > > + * > > > + * This program is distributed in the hope it will be useful, but > > > +WITHOUT > > > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY > > > +or > > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public > > > +License > > > for > > > + * more details. > > > + * > > > + */ > > > + > > > +/* > > > + * Based on Freescale QorIQ Thermal Monitoring Unit (TMU) */ > > > > What does this comment mean? This *is* the "Freescale QorIQ Thermal > > Monitoring Unit" driver. > > I mean thermal management based on the monitor TMU. > I could remove this comment though. > > > > > > +#include <linux/cpufreq.h> > > > > What do you use from this header? > > Sorry, forget to remove it from last version in which cooling devices are > registered in thermal driver instead of cpufreq driver. > > > > > > +#include <linux/module.h> > > > +#include <linux/platform_device.h> > > > +#include <linux/err.h> > > > +#include <linux/io.h> > > > +#include <linux/of.h> > > > +#include <linux/of_address.h> > > > +#include <linux/thermal.h> > > > + > > > +#include "thermal_core.h" > > > + > > > +#define SITES_MAX 16 > > > + > > > +/* > > > + * QorIQ TMU Registers > > > + */ > > > +struct qoriq_tmu_site_regs { > > > + __be32 tritsr; /* Immediate Temperature Site Register */ > > > + __be32 tratsr; /* Average Temperature Site Register */ > > > + u8 res0[0x8]; > > > +} __packed; > > > + > > > +struct qoriq_tmu_regs { > > > + __be32 tmr; /* Mode Register */ > > > +#define TMR_DISABLE 0x0 > > > +#define TMR_ME 0x80000000 > > > +#define TMR_ALPF 0x0c000000 > > > +#define TMR_MSITE 0x00008000 /* Core temperature site */ > > > +#define TMR_ALL (TMR_ME | TMR_ALPF | TMR_MSITE) > > > + __be32 tsr; /* Status Register */ > > > + __be32 tmtmir; /* Temperature measurement interval > > Register */ > > > +#define TMTMIR_DEFAULT 0x00000007 > > > + u8 res0[0x14]; > > > + __be32 tier; /* Interrupt Enable Register */ > > > +#define TIER_DISABLE 0x0 > > > + __be32 tidr; /* Interrupt Detect Register */ > > > + __be32 tiscr; /* Interrupt Site Capture Register */ > > > + __be32 ticscr; /* Interrupt Critical Site Capture > > Register */ > > > + u8 res1[0x10]; > > > + __be32 tmhtcrh; /* High Temperature Capture Register */ > > > + __be32 tmhtcrl; /* Low Temperature Capture Register */ > > > + u8 res2[0x8]; > > > + __be32 tmhtitr; /* High Temperature Immediate Threshold > > */ > > > + __be32 tmhtatr; /* High Temperature Average Threshold */ > > > + __be32 tmhtactr; /* High Temperature Average Crit > > Threshold */ > > > + u8 res3[0x24]; > > > + __be32 ttcfgr; /* Temperature Configuration Register */ > > > + __be32 tscfgr; /* Sensor Configuration Register */ > > > + u8 res4[0x78]; > > > + struct qoriq_tmu_site_regs site[SITES_MAX]; > > > + u8 res5[0x9f8]; > > > + __be32 ipbrr0; /* IP Block Revision Register 0 */ > > > + __be32 ipbrr1; /* IP Block Revision Register 1 */ > > > + u8 res6[0x310]; > > > + __be32 ttr0cr; /* Temperature Range 0 Control Register > > */ > > > + __be32 ttr1cr; /* Temperature Range 1 Control Register > > */ > > > + __be32 ttr2cr; /* Temperature Range 2 Control Register > > */ > > > + __be32 ttr3cr; /* Temperature Range 3 Control Register > > */ > > > +}; > > > + > > > +/* > > > + * Thermal zone data > > > + */ > > > +struct qoriq_tmu_data { > > > + struct thermal_zone_device *tz; > > > + struct qoriq_tmu_regs __iomem *regs; }; > > > + > > > > > +static int tmu_get_temp(void *p, int *temp) { > > > + u8 val; > > > + struct qoriq_tmu_data *data = p; > > > + > > > + val = ioread32be(&data->regs->site[0].tritsr); > > > + *temp = (int)val * 1000; > > > > Why don't you declare val as int in the first place? > > It's a 32bit register. > Only the least significant 8 bits represent the temperature. > The most significant bit shows the validness of the value. > I use u8 type to remove the rest 24bits influence. > > > > > > + for (i = 0; i < len; i += 8, calibration += 2) { > > > + val = (int)of_read_number(calibration, 1); > > > + iowrite32be(val, &data->regs->ttcfgr); > > > + val = (int)of_read_number(calibration + 1, 1); > > > + iowrite32be(val, &data->regs->tscfgr); > > > > Unnecessary casts. > > Ok. > > > > > > + } > > > + > > > + return 0; > > > +} > > > + > > > +static void qoriq_tmu_init_device(struct qoriq_tmu_data *data) { > > > + /* Disable interrupt, using polling instead */ > > > + iowrite32be(TIER_DISABLE, &data->regs->tier); > > > + > > > + /* Set update_interval */ > > > + iowrite32be(TMTMIR_DEFAULT, &data->regs->tmtmir); > > > + > > > + /* Enable monitoring */ > > > + iowrite32be(TMR_ALL, &data->regs->tmr); } > > > + > > > +static struct thermal_zone_of_device_ops tmu_tz_ops = { > > > + .get_temp = tmu_get_temp, > > > +}; > > > + > > > +static int qoriq_tmu_probe(struct platform_device *pdev) { > > > + int ret; > > > + const struct thermal_trip *trip; > > > + struct qoriq_tmu_data *data; > > > + > > > + if (!pdev->dev.of_node) { > > > + dev_err(&pdev->dev, "Device OF-Node is NULL"); > > > + return -EFAULT; > > > + } > > > > EFAULT is for bad user addresses and is not appropriate here. > > I will change it to ENODEV. > > > > > > + > > > + data = devm_kzalloc(&pdev->dev, sizeof(struct qoriq_tmu_data), > > > + GFP_KERNEL); > > > + if (!data) > > > + return -ENOMEM; > > > + > > > + platform_set_drvdata(pdev, data); > > > + data->regs = of_iomap(pdev->dev.of_node, 0); > > > + > > > + if (!data->regs) { > > > + dev_err(&pdev->dev, "Failed to get memory region\n"); > > > + ret = -ENODEV; > > > + goto err_iomap; > > > + } > > > + > > > + ret = qoriq_tmu_calibration(pdev); /* TMU calibration */ > > > + if (ret < 0) { > > > + dev_err(&pdev->dev, "TMU calibration failed.\n"); > > > + ret = -ENODEV; > > > + goto err_iomap; > > > + } > > > > That function returns negative when device tree properties are missing, > > not when a calibration procedure fails. > > What's your suggestion here to return then? > > > > > > + > > > + qoriq_tmu_init_device(data); /* TMU initialization */ > > > + > > > + data->tz = thermal_zone_of_sensor_register(&pdev->dev, 0, > > > + data, &tmu_tz_ops); > > > + if (IS_ERR(data->tz)) { > > > + ret = PTR_ERR(data->tz); > > > + dev_err(&pdev->dev, > > > + "Failed to register thermal zone device %d\n", > > ret); > > > + goto err_thermal; > > > + } > > > + > > > + trip = of_thermal_get_trip_points(data->tz); > > > + > > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); > > > > Doesn't thermal_zone_of_sensor_register() already call ops->set_mode with > > TERMAL_DEVICE_ENABLED? > > You are right. > I referenced the code from other platform and did not notice this. > Thanks. > > > > > > + > > > + return 0; > > > + > > > +err_thermal: > > > + iounmap(data->regs); > > > + > > > +err_iomap: > > > + platform_set_drvdata(pdev, NULL); > > > + devm_kfree(&pdev->dev, data); > > > + > > > + return ret; > > > +} > > > + > > > +static int qoriq_tmu_remove(struct platform_device *pdev) { > > > + struct qoriq_tmu_data *data = platform_get_drvdata(pdev); > > > + > > > + /* Disable monitoring */ > > > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > > > + > > > + thermal_zone_of_sensor_unregister(&pdev->dev, data->tz); > > > + iounmap(data->regs); > > > + > > > + platform_set_drvdata(pdev, NULL); > > > + devm_kfree(&pdev->dev, data); > > > + > > > + return 0; > > > +} > > > + > > > +#ifdef CONFIG_PM_SLEEP > > > +static int qoriq_tmu_suspend(struct device *dev) { > > > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > > > + > > > + /* Disable monitoring */ > > > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_DISABLED); > > > + > > > + return 0; > > > +} > > > + > > > +static int qoriq_tmu_resume(struct device *dev) { > > > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > > > + > > > + /* Enable monitoring */ > > > + iowrite32be(TMR_ALL, &data->regs->tmr); > > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); > > > + > > > + return 0; > > > +} > > > +#endif > > > + > > > +static SIMPLE_DEV_PM_OPS(qoriq_tmu_pm_ops, > > > + qoriq_tmu_suspend, qoriq_tmu_resume); > > > + > > > > > > > +static const struct of_device_id qoriq_tmu_match[] = { > > > + { .compatible = "fsl,qoriq-tmu", }, > > > + {}, > > > +}; > > > > Binding? > > Not send out yet. > I planned to send the patch with device tree patchset including > adding TMU node to T1040/T1024/LS1021A platform. > > It's depending on the device tree files moving patch I sent out > not long ago. > > > > > > + > > > +static struct platform_driver qoriq_tmu = { > > > + .driver = { > > > + .name = "qoriq_thermal", > > > + .pm = &qoriq_tmu_pm_ops, > > > + .of_match_table = qoriq_tmu_match, > > > + }, > > > > Why the tabs after ".name"? > > Will indent the other two. > > > > > -Scott >
On Wed, 2015-11-04 at 11:24 -0800, Eduardo Valentin wrote: > On Fri, Sep 25, 2015 at 03:09:42AM +0000, Hongtao Jia wrote: > > > > > -----Original Message----- > > > From: Wood Scott-B07421 > > > Sent: Friday, September 25, 2015 6:10 AM > > > To: Jia Hongtao-B38951 > > > Cc: edubezval@gmail.com; linux-pm@vger.kernel.org; linuxppc- > > > dev@lists.ozlabs.org > > > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management support > > > > > > On Wed, 2015-09-23 at 16:28 +0800, Jia Hongtao wrote: > > > > This driver add thermal management support by enabling TMU (Thermal > > > > Monitoring Unit) on QorIQ platform. > > > > > > > > It's based on thermal of framework: > > > > - Trip points defined in device tree. > > > > - Cpufreq as cooling device registered in qoriq cpufreq driver. > > > > > > I don't see any cooling device registered in the qoriq cpufreq driver. > > > Is this dependent on some other patch? > > > > It's not depend on any patch. But I saw your patch below: > > [PATCH v3 5/5] cpufreq: qoriq: Don't look at clock implementation details > > So I hold my patch waiting for your patch merged or there will be > > conflict. > > > > I could send it out too if you are fine with it. > > Would you guys benefit of cpufreq-cpu0? If you mean cpufreq-dt, no, as I explained in https://lkml.org/lkml/2015/9/18/699 -Scott
> -----Original Message----- > From: Eduardo Valentin [mailto:edubezval@gmail.com] > Sent: Thursday, November 05, 2015 3:25 AM > To: Jia Hongtao-B38951 > Cc: Wood Scott-B07421; linux-pm@vger.kernel.org; linuxppc- > dev@lists.ozlabs.org > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management support > > On Fri, Sep 25, 2015 at 03:09:42AM +0000, Hongtao Jia wrote: > > > > > -----Original Message----- > > > From: Wood Scott-B07421 > > > Sent: Friday, September 25, 2015 6:10 AM > > > To: Jia Hongtao-B38951 > > > Cc: edubezval@gmail.com; linux-pm@vger.kernel.org; linuxppc- > > > dev@lists.ozlabs.org > > > Subject: Re: [PATCH V3] thermal: qoriq: Add thermal management > > > support > > > > > > On Wed, 2015-09-23 at 16:28 +0800, Jia Hongtao wrote: > > > > This driver add thermal management support by enabling TMU > > > > (Thermal Monitoring Unit) on QorIQ platform. > > > > > > > > It's based on thermal of framework: > > > > - Trip points defined in device tree. > > > > - Cpufreq as cooling device registered in qoriq cpufreq driver. > > > > > > I don't see any cooling device registered in the qoriq cpufreq driver. > > > Is this dependent on some other patch? > > > > It's not depend on any patch. But I saw your patch below: > > [PATCH v3 5/5] cpufreq: qoriq: Don't look at clock implementation > > details So I hold my patch waiting for your patch merged or there will > be conflict. > > > > I could send it out too if you are fine with it. > > Would you guys benefit of cpufreq-cpu0? > > > > > > > > > > > > > > > > > Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com> > > > > --- > > > > V3: Using thermal of framework. > > > > > > > > drivers/thermal/Kconfig | 11 ++ > > > > drivers/thermal/Makefile | 1 + > > > > drivers/thermal/qoriq_thermal.c | 267 > > Please include a binding description in your next version. Also, remember > to include an example of your binding. > > > > > > > ++++++++++++++++++++++++++++++++++++++++ > > > > 3 files changed, 279 insertions(+) create mode 100644 > > > > drivers/thermal/qoriq_thermal.c > > > > > > > > diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig > > > > index 0390044..c91041b 100644 > > > > --- a/drivers/thermal/Kconfig > > > > +++ b/drivers/thermal/Kconfig > > > > @@ -180,6 +180,17 @@ config IMX_THERMAL > > > > cpufreq is used as the cooling device to throttle CPUs when > the > > > > passive trip is crossed. > > > > > > > > +config QORIQ_THERMAL > > > It would be really great if you could consolidate this driver with > IMX_THERMAL. Do you think it is doable? The TMU IP on I.MX and QorIQ platform are completely different and they use the different cpufreq driver. I don't think they could share the same thermal driver elegantly. -Hongtao. > > > > > + tristate "Freescale QorIQ Thermal Monitoring Unit" > > > > + depends on CPU_THERMAL > > > > + depends on THERMAL_OF > > > > + default n > > > > + help > > > > + Enable thermal management based on Freescale QorIQ Thermal > > > Monitoring > > > > + Unit (TMU). It supports one critical trip point and one > > > > + passive > > > trip > > > > + point. The cpufreq is used as the cooling device to > > > > + throttle > > > CPUs when > > > > + the passive trip is crossed. > > > > > > "default n" is unnecessary -- n is already the default. > > > > Right. > > > > > > > > Where is the interaction between this driver and cpufreq? > > > > It's all in cpufreq patch I mentioned above. > > > > > > > > > config SPEAR_THERMAL > > > > bool "SPEAr thermal sensor driver" > > > > depends on PLAT_SPEAR > > > > diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile > > > > index > > > > 26f1608..e55d703 100644 > > > > --- a/drivers/thermal/Makefile > > > > +++ b/drivers/thermal/Makefile > > > > @@ -33,6 +33,7 @@ obj-$(CONFIG_DOVE_THERMAL) += > dove_thermal.o > > > > obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o > > > > obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o > > > > obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o > > > > +obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o > > > > obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o > > > > obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o > > > > obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o > > > > diff --git a/drivers/thermal/qoriq_thermal.c > > > > b/drivers/thermal/qoriq_thermal.c new file mode 100644 index > > > > 0000000..7c2a3261 > > > > --- /dev/null > > > > +++ b/drivers/thermal/qoriq_thermal.c > > > > @@ -0,0 +1,267 @@ > > > > +/* > > > > + * Copyright 2015 Freescale Semiconductor, Inc. > > > > + * > > > > + * This program is free software; you can redistribute it and/or > > > > +modify it > > > > + * under the terms and conditions of the GNU General Public > > > > +License, > > > > + * version 2, as published by the Free Software Foundation. > > > > + * > > > > + * This program is distributed in the hope it will be useful, but > > > > +WITHOUT > > > > + * ANY WARRANTY; without even the implied warranty of > > > > +MERCHANTABILITY or > > > > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public > > > > +License > > > > for > > > > + * more details. > > > > + * > > > > + */ > > > > + > > > > +/* > > > > + * Based on Freescale QorIQ Thermal Monitoring Unit (TMU) */ > > > > > > What does this comment mean? This *is* the "Freescale QorIQ Thermal > > > Monitoring Unit" driver. > > > > I mean thermal management based on the monitor TMU. > > I could remove this comment though. > > > > > > > > > +#include <linux/cpufreq.h> > > > > > > What do you use from this header? > > > > Sorry, forget to remove it from last version in which cooling devices > > are registered in thermal driver instead of cpufreq driver. > > > > > > > > > +#include <linux/module.h> > > > > +#include <linux/platform_device.h> #include <linux/err.h> > > > > +#include <linux/io.h> #include <linux/of.h> #include > > > > +<linux/of_address.h> #include <linux/thermal.h> > > > > + > > > > +#include "thermal_core.h" > > > > + > > > > +#define SITES_MAX 16 > > > > + > > > > +/* > > > > + * QorIQ TMU Registers > > > > + */ > > > > +struct qoriq_tmu_site_regs { > > > > + __be32 tritsr; /* Immediate Temperature Site > Register */ > > > > + __be32 tratsr; /* Average Temperature Site Register > */ > > > > + u8 res0[0x8]; > > > > +} __packed; > > > > + > > > > +struct qoriq_tmu_regs { > > > > + __be32 tmr; /* Mode Register */ > > > > +#define TMR_DISABLE 0x0 > > > > +#define TMR_ME 0x80000000 > > > > +#define TMR_ALPF 0x0c000000 > > > > +#define TMR_MSITE 0x00008000 /* Core temperature site */ > > > > +#define TMR_ALL (TMR_ME | TMR_ALPF | TMR_MSITE) > > > > + __be32 tsr; /* Status Register */ > > > > + __be32 tmtmir; /* Temperature measurement interval > > > Register */ > > > > +#define TMTMIR_DEFAULT 0x00000007 > > > > + u8 res0[0x14]; > > > > + __be32 tier; /* Interrupt Enable Register */ > > > > +#define TIER_DISABLE 0x0 > > > > + __be32 tidr; /* Interrupt Detect Register */ > > > > + __be32 tiscr; /* Interrupt Site Capture Register */ > > > > + __be32 ticscr; /* Interrupt Critical Site Capture > > > Register */ > > > > + u8 res1[0x10]; > > > > + __be32 tmhtcrh; /* High Temperature Capture Register > */ > > > > + __be32 tmhtcrl; /* Low Temperature Capture Register > */ > > > > + u8 res2[0x8]; > > > > + __be32 tmhtitr; /* High Temperature Immediate > Threshold > > > */ > > > > + __be32 tmhtatr; /* High Temperature Average Threshold > */ > > > > + __be32 tmhtactr; /* High Temperature Average Crit > > > Threshold */ > > > > + u8 res3[0x24]; > > > > + __be32 ttcfgr; /* Temperature Configuration Register > */ > > > > + __be32 tscfgr; /* Sensor Configuration Register */ > > > > + u8 res4[0x78]; > > > > + struct qoriq_tmu_site_regs site[SITES_MAX]; > > > > + u8 res5[0x9f8]; > > > > + __be32 ipbrr0; /* IP Block Revision Register 0 */ > > > > + __be32 ipbrr1; /* IP Block Revision Register 1 */ > > > > + u8 res6[0x310]; > > > > + __be32 ttr0cr; /* Temperature Range 0 Control > Register > > > */ > > > > + __be32 ttr1cr; /* Temperature Range 1 Control > Register > > > */ > > > > + __be32 ttr2cr; /* Temperature Range 2 Control > Register > > > */ > > > > + __be32 ttr3cr; /* Temperature Range 3 Control > Register > > > */ > > > > +}; > > > > + > > > > +/* > > > > + * Thermal zone data > > > > + */ > > > > +struct qoriq_tmu_data { > > > > + struct thermal_zone_device *tz; > > > > + struct qoriq_tmu_regs __iomem *regs; }; > > > > + > > > > > > > +static int tmu_get_temp(void *p, int *temp) { > > > > + u8 val; > > > > + struct qoriq_tmu_data *data = p; > > > > + > > > > + val = ioread32be(&data->regs->site[0].tritsr); > > > > + *temp = (int)val * 1000; > > > > > > Why don't you declare val as int in the first place? > > > > It's a 32bit register. > > Only the least significant 8 bits represent the temperature. > > The most significant bit shows the validness of the value. > > I use u8 type to remove the rest 24bits influence. > > > > > > > > > + for (i = 0; i < len; i += 8, calibration += 2) { > > > > + val = (int)of_read_number(calibration, 1); > > > > + iowrite32be(val, &data->regs->ttcfgr); > > > > + val = (int)of_read_number(calibration + 1, 1); > > > > + iowrite32be(val, &data->regs->tscfgr); > > > > > > Unnecessary casts. > > > > Ok. > > > > > > > > > + } > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static void qoriq_tmu_init_device(struct qoriq_tmu_data *data) { > > > > + /* Disable interrupt, using polling instead */ > > > > + iowrite32be(TIER_DISABLE, &data->regs->tier); > > > > + > > > > + /* Set update_interval */ > > > > + iowrite32be(TMTMIR_DEFAULT, &data->regs->tmtmir); > > > > + > > > > + /* Enable monitoring */ > > > > + iowrite32be(TMR_ALL, &data->regs->tmr); } > > > > + > > > > +static struct thermal_zone_of_device_ops tmu_tz_ops = { > > > > + .get_temp = tmu_get_temp, > > > > +}; > > > > + > > > > +static int qoriq_tmu_probe(struct platform_device *pdev) { > > > > + int ret; > > > > + const struct thermal_trip *trip; > > > > + struct qoriq_tmu_data *data; > > > > + > > > > + if (!pdev->dev.of_node) { > > > > + dev_err(&pdev->dev, "Device OF-Node is NULL"); > > > > + return -EFAULT; > > > > + } > > > > > > EFAULT is for bad user addresses and is not appropriate here. > > > > I will change it to ENODEV. > > > > > > > > > + > > > > + data = devm_kzalloc(&pdev->dev, sizeof(struct qoriq_tmu_data), > > > > + GFP_KERNEL); > > > > + if (!data) > > > > + return -ENOMEM; > > > > + > > > > + platform_set_drvdata(pdev, data); > > > > + data->regs = of_iomap(pdev->dev.of_node, 0); > > > > + > > > > + if (!data->regs) { > > > > + dev_err(&pdev->dev, "Failed to get memory region\n"); > > > > + ret = -ENODEV; > > > > + goto err_iomap; > > > > + } > > > > + > > > > + ret = qoriq_tmu_calibration(pdev); /* TMU calibration */ > > > > + if (ret < 0) { > > > > + dev_err(&pdev->dev, "TMU calibration failed.\n"); > > > > + ret = -ENODEV; > > > > + goto err_iomap; > > > > + } > > > > > > That function returns negative when device tree properties are > > > missing, not when a calibration procedure fails. > > > > What's your suggestion here to return then? > > > > > > > > > + > > > > + qoriq_tmu_init_device(data); /* TMU initialization */ > > > > + > > > > + data->tz = thermal_zone_of_sensor_register(&pdev->dev, 0, > > > > + data, &tmu_tz_ops); > > > > + if (IS_ERR(data->tz)) { > > > > + ret = PTR_ERR(data->tz); > > > > + dev_err(&pdev->dev, > > > > + "Failed to register thermal zone device > > > > + %d\n", > > > ret); > > > > + goto err_thermal; > > > > + } > > > > + > > > > + trip = of_thermal_get_trip_points(data->tz); > > > > + > > > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); > > > > > > Doesn't thermal_zone_of_sensor_register() already call ops->set_mode > > > with TERMAL_DEVICE_ENABLED? > > > > You are right. > > I referenced the code from other platform and did not notice this. > > Thanks. > > > > > > > > > + > > > > + return 0; > > > > + > > > > +err_thermal: > > > > + iounmap(data->regs); > > > > + > > > > +err_iomap: > > > > + platform_set_drvdata(pdev, NULL); > > > > + devm_kfree(&pdev->dev, data); > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static int qoriq_tmu_remove(struct platform_device *pdev) { > > > > + struct qoriq_tmu_data *data = platform_get_drvdata(pdev); > > > > + > > > > + /* Disable monitoring */ > > > > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > > > > + > > > > + thermal_zone_of_sensor_unregister(&pdev->dev, data->tz); > > > > + iounmap(data->regs); > > > > + > > > > + platform_set_drvdata(pdev, NULL); > > > > + devm_kfree(&pdev->dev, data); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +#ifdef CONFIG_PM_SLEEP > > > > +static int qoriq_tmu_suspend(struct device *dev) { > > > > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > > > > + > > > > + /* Disable monitoring */ > > > > + iowrite32be(TMR_DISABLE, &data->regs->tmr); > > > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_DISABLED); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static int qoriq_tmu_resume(struct device *dev) { > > > > + struct qoriq_tmu_data *data = dev_get_drvdata(dev); > > > > + > > > > + /* Enable monitoring */ > > > > + iowrite32be(TMR_ALL, &data->regs->tmr); > > > > + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); > > > > + > > > > + return 0; > > > > +} > > > > +#endif > > > > + > > > > +static SIMPLE_DEV_PM_OPS(qoriq_tmu_pm_ops, > > > > + qoriq_tmu_suspend, qoriq_tmu_resume); > > > > + > > > > > > > > > > +static const struct of_device_id qoriq_tmu_match[] = { > > > > + { .compatible = "fsl,qoriq-tmu", }, > > > > + {}, > > > > +}; > > > > > > Binding? > > > > Not send out yet. > > I planned to send the patch with device tree patchset including adding > > TMU node to T1040/T1024/LS1021A platform. > > > > It's depending on the device tree files moving patch I sent out not > > long ago. > > > > > > > > > + > > > > +static struct platform_driver qoriq_tmu = { > > > > + .driver = { > > > > + .name = "qoriq_thermal", > > > > + .pm = &qoriq_tmu_pm_ops, > > > > + .of_match_table = qoriq_tmu_match, > > > > + }, > > > > > > Why the tabs after ".name"? > > > > Will indent the other two. > > > > > > > > -Scott > >
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index 0390044..c91041b 100644 --- a/drivers/thermal/Kconfig +++ b/drivers/thermal/Kconfig @@ -180,6 +180,17 @@ config IMX_THERMAL cpufreq is used as the cooling device to throttle CPUs when the passive trip is crossed. +config QORIQ_THERMAL + tristate "Freescale QorIQ Thermal Monitoring Unit" + depends on CPU_THERMAL + depends on THERMAL_OF + default n + help + Enable thermal management based on Freescale QorIQ Thermal Monitoring + Unit (TMU). It supports one critical trip point and one passive trip + point. The cpufreq is used as the cooling device to throttle CPUs when + the passive trip is crossed. + config SPEAR_THERMAL bool "SPEAr thermal sensor driver" depends on PLAT_SPEAR diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index 26f1608..e55d703 100644 --- a/drivers/thermal/Makefile +++ b/drivers/thermal/Makefile @@ -33,6 +33,7 @@ obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o +obj-$(CONFIG_QORIQ_THERMAL) += qoriq_thermal.o obj-$(CONFIG_DB8500_CPUFREQ_COOLING) += db8500_cpufreq_cooling.o obj-$(CONFIG_INTEL_POWERCLAMP) += intel_powerclamp.o obj-$(CONFIG_X86_PKG_TEMP_THERMAL) += x86_pkg_temp_thermal.o diff --git a/drivers/thermal/qoriq_thermal.c b/drivers/thermal/qoriq_thermal.c new file mode 100644 index 0000000..7c2a3261 --- /dev/null +++ b/drivers/thermal/qoriq_thermal.c @@ -0,0 +1,267 @@ +/* + * Copyright 2015 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + */ + +/* + * Based on Freescale QorIQ Thermal Monitoring Unit (TMU) + */ +#include <linux/cpufreq.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/thermal.h> + +#include "thermal_core.h" + +#define SITES_MAX 16 + +/* + * QorIQ TMU Registers + */ +struct qoriq_tmu_site_regs { + __be32 tritsr; /* Immediate Temperature Site Register */ + __be32 tratsr; /* Average Temperature Site Register */ + u8 res0[0x8]; +} __packed; + +struct qoriq_tmu_regs { + __be32 tmr; /* Mode Register */ +#define TMR_DISABLE 0x0 +#define TMR_ME 0x80000000 +#define TMR_ALPF 0x0c000000 +#define TMR_MSITE 0x00008000 /* Core temperature site */ +#define TMR_ALL (TMR_ME | TMR_ALPF | TMR_MSITE) + __be32 tsr; /* Status Register */ + __be32 tmtmir; /* Temperature measurement interval Register */ +#define TMTMIR_DEFAULT 0x00000007 + u8 res0[0x14]; + __be32 tier; /* Interrupt Enable Register */ +#define TIER_DISABLE 0x0 + __be32 tidr; /* Interrupt Detect Register */ + __be32 tiscr; /* Interrupt Site Capture Register */ + __be32 ticscr; /* Interrupt Critical Site Capture Register */ + u8 res1[0x10]; + __be32 tmhtcrh; /* High Temperature Capture Register */ + __be32 tmhtcrl; /* Low Temperature Capture Register */ + u8 res2[0x8]; + __be32 tmhtitr; /* High Temperature Immediate Threshold */ + __be32 tmhtatr; /* High Temperature Average Threshold */ + __be32 tmhtactr; /* High Temperature Average Crit Threshold */ + u8 res3[0x24]; + __be32 ttcfgr; /* Temperature Configuration Register */ + __be32 tscfgr; /* Sensor Configuration Register */ + u8 res4[0x78]; + struct qoriq_tmu_site_regs site[SITES_MAX]; + u8 res5[0x9f8]; + __be32 ipbrr0; /* IP Block Revision Register 0 */ + __be32 ipbrr1; /* IP Block Revision Register 1 */ + u8 res6[0x310]; + __be32 ttr0cr; /* Temperature Range 0 Control Register */ + __be32 ttr1cr; /* Temperature Range 1 Control Register */ + __be32 ttr2cr; /* Temperature Range 2 Control Register */ + __be32 ttr3cr; /* Temperature Range 3 Control Register */ +}; + +/* + * Thermal zone data + */ +struct qoriq_tmu_data { + struct thermal_zone_device *tz; + struct qoriq_tmu_regs __iomem *regs; +}; + +static int tmu_get_temp(void *p, int *temp) +{ + u8 val; + struct qoriq_tmu_data *data = p; + + val = ioread32be(&data->regs->site[0].tritsr); + *temp = (int)val * 1000; + + return 0; +} + +static int qoriq_tmu_calibration(struct platform_device *pdev) +{ + int i, val, len; + u32 range[4]; + const __be32 *calibration; + struct device_node *node = pdev->dev.of_node; + struct qoriq_tmu_data *data = platform_get_drvdata(pdev); + + /* Disable monitoring before calibration */ + iowrite32be(TMR_DISABLE, &data->regs->tmr); + + if (of_property_read_u32_array(node, "fsl,tmu-range", range, 4)) + return -1; + + /* Init temperature range registers */ + iowrite32be(range[0], &data->regs->ttr0cr); + iowrite32be(range[1], &data->regs->ttr1cr); + iowrite32be(range[2], &data->regs->ttr2cr); + iowrite32be(range[3], &data->regs->ttr3cr); + + calibration = of_get_property(node, "fsl,tmu-calibration", &len); + if (calibration == NULL) + return -1; + + for (i = 0; i < len; i += 8, calibration += 2) { + val = (int)of_read_number(calibration, 1); + iowrite32be(val, &data->regs->ttcfgr); + val = (int)of_read_number(calibration + 1, 1); + iowrite32be(val, &data->regs->tscfgr); + } + + return 0; +} + +static void qoriq_tmu_init_device(struct qoriq_tmu_data *data) +{ + /* Disable interrupt, using polling instead */ + iowrite32be(TIER_DISABLE, &data->regs->tier); + + /* Set update_interval */ + iowrite32be(TMTMIR_DEFAULT, &data->regs->tmtmir); + + /* Enable monitoring */ + iowrite32be(TMR_ALL, &data->regs->tmr); +} + +static struct thermal_zone_of_device_ops tmu_tz_ops = { + .get_temp = tmu_get_temp, +}; + +static int qoriq_tmu_probe(struct platform_device *pdev) +{ + int ret; + const struct thermal_trip *trip; + struct qoriq_tmu_data *data; + + if (!pdev->dev.of_node) { + dev_err(&pdev->dev, "Device OF-Node is NULL"); + return -EFAULT; + } + + data = devm_kzalloc(&pdev->dev, sizeof(struct qoriq_tmu_data), + GFP_KERNEL); + if (!data) + return -ENOMEM; + + platform_set_drvdata(pdev, data); + data->regs = of_iomap(pdev->dev.of_node, 0); + + if (!data->regs) { + dev_err(&pdev->dev, "Failed to get memory region\n"); + ret = -ENODEV; + goto err_iomap; + } + + ret = qoriq_tmu_calibration(pdev); /* TMU calibration */ + if (ret < 0) { + dev_err(&pdev->dev, "TMU calibration failed.\n"); + ret = -ENODEV; + goto err_iomap; + } + + qoriq_tmu_init_device(data); /* TMU initialization */ + + data->tz = thermal_zone_of_sensor_register(&pdev->dev, 0, + data, &tmu_tz_ops); + if (IS_ERR(data->tz)) { + ret = PTR_ERR(data->tz); + dev_err(&pdev->dev, + "Failed to register thermal zone device %d\n", ret); + goto err_thermal; + } + + trip = of_thermal_get_trip_points(data->tz); + + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); + + return 0; + +err_thermal: + iounmap(data->regs); + +err_iomap: + platform_set_drvdata(pdev, NULL); + devm_kfree(&pdev->dev, data); + + return ret; +} + +static int qoriq_tmu_remove(struct platform_device *pdev) +{ + struct qoriq_tmu_data *data = platform_get_drvdata(pdev); + + /* Disable monitoring */ + iowrite32be(TMR_DISABLE, &data->regs->tmr); + + thermal_zone_of_sensor_unregister(&pdev->dev, data->tz); + iounmap(data->regs); + + platform_set_drvdata(pdev, NULL); + devm_kfree(&pdev->dev, data); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int qoriq_tmu_suspend(struct device *dev) +{ + struct qoriq_tmu_data *data = dev_get_drvdata(dev); + + /* Disable monitoring */ + iowrite32be(TMR_DISABLE, &data->regs->tmr); + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_DISABLED); + + return 0; +} + +static int qoriq_tmu_resume(struct device *dev) +{ + struct qoriq_tmu_data *data = dev_get_drvdata(dev); + + /* Enable monitoring */ + iowrite32be(TMR_ALL, &data->regs->tmr); + data->tz->ops->set_mode(data->tz, THERMAL_DEVICE_ENABLED); + + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(qoriq_tmu_pm_ops, + qoriq_tmu_suspend, qoriq_tmu_resume); + +static const struct of_device_id qoriq_tmu_match[] = { + { .compatible = "fsl,qoriq-tmu", }, + {}, +}; + +static struct platform_driver qoriq_tmu = { + .driver = { + .name = "qoriq_thermal", + .pm = &qoriq_tmu_pm_ops, + .of_match_table = qoriq_tmu_match, + }, + .probe = qoriq_tmu_probe, + .remove = qoriq_tmu_remove, +}; +module_platform_driver(qoriq_tmu); + +MODULE_AUTHOR("Jia Hongtao <hongtao.jia@freescale.com>"); +MODULE_DESCRIPTION("Freescale QorIQ Thermal Monitoring Unit driver"); +MODULE_LICENSE("GPL v2");
This driver add thermal management support by enabling TMU (Thermal Monitoring Unit) on QorIQ platform. It's based on thermal of framework: - Trip points defined in device tree. - Cpufreq as cooling device registered in qoriq cpufreq driver. Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com> --- V3: Using thermal of framework. drivers/thermal/Kconfig | 11 ++ drivers/thermal/Makefile | 1 + drivers/thermal/qoriq_thermal.c | 267 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 279 insertions(+) create mode 100644 drivers/thermal/qoriq_thermal.c