@@ -53,7 +53,7 @@
};
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -41,7 +41,7 @@
};
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "ext_clock";
@@ -52,7 +52,7 @@
status = "okay";
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
@@ -68,7 +68,7 @@
status = "okay";
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -79,7 +79,7 @@
enable-active-high;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
@@ -39,25 +39,35 @@
leds {
compatible = "gpio-leds";
- led-0 {
+ led0: led-0 {
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_BLUE>;
gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+ retain-state-suspended;
};
- led-1 {
+ led1: led-1 {
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_GREEN>;
gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
+ retain-state-suspended;
};
- led-2 {
+ led2: led-2 {
function = LED_FUNCTION_INDICATOR;
color = <LED_COLOR_ID_RED>;
gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+ retain-state-suspended;
};
};
+ multi-led {
+ compatible = "leds-group-multicolor";
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_INDICATOR;
+ leds = <&led0>, <&led1>, <&led2>;
+ };
+
reg_ps: ps-regulator {
compatible = "regulator-fixed";
regulator-name = "ps";
@@ -98,7 +98,7 @@
enable-active-high;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
post-power-on-delay-ms = <200>;
@@ -74,7 +74,7 @@
status = "okay";
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
@@ -107,27 +107,19 @@
gpu_opp_table: opp-table-gpu {
compatible = "operating-points-v2";
- opp-120000000 {
- opp-hz = /bits/ 64 <120000000>;
- };
-
- opp-312000000 {
- opp-hz = /bits/ 64 <312000000>;
- };
-
opp-432000000 {
opp-hz = /bits/ 64 <432000000>;
};
};
- osc24M: osc24M_clk {
+ osc24M: osc24M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
- osc32k: osc32k_clk {
+ osc32k: osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -216,21 +208,21 @@
};
trips {
- cpu_alert0: cpu_alert0 {
+ cpu_alert0: cpu-alert0 {
/* milliCelsius */
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
- cpu_alert1: cpu_alert1 {
+ cpu_alert1: cpu-alert1 {
/* milliCelsius */
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
- cpu_crit: cpu_crit {
+ cpu_crit: cpu-crit {
/* milliCelsius */
temperature = <110000>;
hysteresis = <2000>;
new file mode 100644
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Tanix TX1";
+ compatible = "oranth,tanix-tx1", "allwinner,sun50i-h616";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &sdio_wifi;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ key {
+ label = "hidden";
+ linux,code = <BTN_0>;
+ gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 */
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ default-state = "on";
+ };
+ };
+
+ wifi_pwrseq: pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc CLK_OSC32K_FANOUT>;
+ clock-names = "ext_clock";
+ pinctrl-0 = <&x32clk_fanout_pin>;
+ pinctrl-names = "default";
+ reset-gpios = <&pio 6 18 GPIO_ACTIVE_LOW>; /* PG18 */
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the DC input */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ir {
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_aldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ sdio_wifi: wifi@1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ vmmc-supply = <®_dldo1>;
+ vqmmc-supply = <®_aldo1>;
+ bus-width = <8>;
+ non-removable;
+ max-frequency = <100000000>;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pc-supply = <®_aldo1>;
+ vcc-pf-supply = <®_dldo1>;
+ vcc-pg-supply = <®_aldo1>;
+ vcc-ph-supply = <®_dldo1>;
+ vcc-pi-supply = <®_dldo1>;
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp313: pmic@36 {
+ compatible = "x-powers,axp313a";
+ reg = <0x36>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+
+ vin1-supply = <®_vcc5v>;
+ vin2-supply = <®_vcc5v>;
+ vin3-supply = <®_vcc5v>;
+
+ regulators {
+ /* Supplies VCC-PLL, so needs to be always on. */
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ /* Supplies VCC-IO, so needs to be always on. */
+ reg_dldo1: dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <990000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd-dram";
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "host"; /* USB A type receptable */
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
@@ -68,7 +68,7 @@
states = <1100000 0>, <1300000 1>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
post-power-on-delay-ms = <200>;
@@ -103,7 +103,7 @@
states = <1100000 0x0>, <1300000 0x1>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
post-power-on-delay-ms = <200>;
@@ -170,7 +170,7 @@
non-removable;
status = "okay";
- rtl8189etv: sdio_wifi@1 {
+ rtl8189etv: wifi@1 {
reg = <1>;
};
};
@@ -85,7 +85,7 @@
status = "okay";
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 2 14 GPIO_ACTIVE_LOW>; /* PC14 */
};
@@ -97,7 +97,7 @@
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
- rtl8189ftv: sdio_wifi@1 {
+ rtl8189ftv: wifi@1 {
reg = <1>;
};
};
@@ -52,7 +52,7 @@
regulator-max-microvolt = <3300000>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
post-power-on-delay-ms = <200>;
@@ -34,7 +34,7 @@
};
};
- ext_osc32k: ext_osc32k_clk {
+ ext_osc32k: ext-osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -33,7 +33,7 @@
};
};
- ext_osc32k: ext_osc32k_clk {
+ ext_osc32k: ext-osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -11,7 +11,7 @@
serial1 = &uart1; /* BT-UART */
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "ext_clock";
@@ -32,7 +32,7 @@
};
};
- ext_osc32k: ext_osc32k_clk {
+ ext_osc32k: ext-osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -5,13 +5,13 @@
#include "sun50i-h6-pine-h64.dts"
+/delete-node/ ®_gmac_3v3;
+
/ {
model = "Pine H64 model B";
compatible = "pine64,pine-h64-model-b", "allwinner,sun50i-h6";
- /delete-node/ reg_gmac_3v3;
-
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
post-power-on-delay-ms = <200>;
@@ -22,7 +22,7 @@
stdout-path = "serial0:115200n8";
};
- ext_osc32k: ext_osc32k_clk {
+ ext_osc32k: ext-osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -68,7 +68,7 @@
status = "disabled";
};
- osc24M: osc24M_clk {
+ osc24M: osc24M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
@@ -6,6 +6,7 @@
/dts-v1/;
#include "sun50i-h616.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -62,6 +63,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&mmc0 {
vmmc-supply = <®_dldo1>;
/* Card detection pin is not connected */
new file mode 100644
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2023 Martin Botka <martin@somainline.org>
+
+/ {
+ cpu_opp_table: opp-table-cpu {
+ compatible = "allwinner,sun50i-h616-operating-points";
+ nvmem-cells = <&cpu_speed_grade>;
+ opp-shared;
+
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <900000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x1f>;
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <900000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x12>;
+ };
+
+ opp-720000000 {
+ opp-hz = /bits/ 64 <720000000>;
+ opp-microvolt = <900000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x0d>;
+ };
+
+ opp-792000000 {
+ opp-hz = /bits/ 64 <792000000>;
+ opp-microvolt-speed1 = <900000>;
+ opp-microvolt-speed4 = <940000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x12>;
+ };
+
+ opp-936000000 {
+ opp-hz = /bits/ 64 <936000000>;
+ opp-microvolt = <900000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x0d>;
+ };
+
+ opp-1008000000 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt-speed0 = <950000>;
+ opp-microvolt-speed1 = <940000>;
+ opp-microvolt-speed2 = <950000>;
+ opp-microvolt-speed3 = <950000>;
+ opp-microvolt-speed4 = <1020000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x1f>;
+ };
+
+ opp-1104000000 {
+ opp-hz = /bits/ 64 <1104000000>;
+ opp-microvolt-speed0 = <1000000>;
+ opp-microvolt-speed2 = <1000000>;
+ opp-microvolt-speed3 = <1000000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x0d>;
+ };
+
+ opp-1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt-speed0 = <1050000>;
+ opp-microvolt-speed1 = <1020000>;
+ opp-microvolt-speed2 = <1050000>;
+ opp-microvolt-speed3 = <1050000>;
+ opp-microvolt-speed4 = <1100000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x1f>;
+ };
+
+ opp-1320000000 {
+ opp-hz = /bits/ 64 <1320000000>;
+ opp-microvolt = <1100000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x1d>;
+ };
+
+ opp-1416000000 {
+ opp-hz = /bits/ 64 <1416000000>;
+ opp-microvolt = <1100000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x0d>;
+ };
+
+ opp-1512000000 {
+ opp-hz = /bits/ 64 <1512000000>;
+ opp-microvolt-speed1 = <1100000>;
+ opp-microvolt-speed3 = <1100000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ opp-supported-hw = <0x0a>;
+ };
+ };
+};
+
+&cpu0 {
+ operating-points-v2 = <&cpu_opp_table>;
+};
+
+&cpu1 {
+ operating-points-v2 = <&cpu_opp_table>;
+};
+
+&cpu2 {
+ operating-points-v2 = <&cpu_opp_table>;
+};
+
+&cpu3 {
+ operating-points-v2 = <&cpu_opp_table>;
+};
@@ -6,12 +6,17 @@
/dts-v1/;
#include "sun50i-h616-orangepi-zero.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
/ {
model = "OrangePi Zero2";
compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
};
+&cpu0 {
+ cpu-supply = <®_dcdca>;
+};
+
&emac0 {
allwinner,rx-delay-ps = <3100>;
allwinner,tx-delay-ps = <700>;
@@ -6,6 +6,7 @@
/dts-v1/;
#include "sun50i-h616.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -32,6 +33,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdca>;
+};
+
&ehci0 {
status = "okay";
};
@@ -26,6 +26,7 @@
reg = <0>;
enable-method = "psci";
clocks = <&ccu CLK_CPUX>;
+ #cooling-cells = <2>;
};
cpu1: cpu@1 {
@@ -34,6 +35,7 @@
reg = <1>;
enable-method = "psci";
clocks = <&ccu CLK_CPUX>;
+ #cooling-cells = <2>;
};
cpu2: cpu@2 {
@@ -42,6 +44,7 @@
reg = <2>;
enable-method = "psci";
clocks = <&ccu CLK_CPUX>;
+ #cooling-cells = <2>;
};
cpu3: cpu@3 {
@@ -50,6 +53,7 @@
reg = <3>;
enable-method = "psci";
clocks = <&ccu CLK_CPUX>;
+ #cooling-cells = <2>;
};
};
@@ -156,6 +160,10 @@
ths_calibration: thermal-sensor-calibration@14 {
reg = <0x14 0x8>;
};
+
+ cpu_speed_grade: cpu-speed-grade@0 {
+ reg = <0x0 2>;
+ };
};
watchdog: watchdog@30090a0 {
@@ -194,7 +202,7 @@
};
i2c0_pins: i2c0-pins {
- pins = "PI6", "PI7";
+ pins = "PI5", "PI6";
function = "i2c0";
};
@@ -775,6 +783,15 @@
#reset-cells = <1>;
};
+ nmi_intc: interrupt-controller@7010320 {
+ compatible = "allwinner,sun50i-h616-nmi",
+ "allwinner,sun9i-a80-nmi";
+ reg = <0x07010320 0xc>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
r_pio: pinctrl@7022000 {
compatible = "allwinner,sun50i-h616-r-pinctrl";
reg = <0x07022000 0x400>;
@@ -4,6 +4,11 @@
*/
#include "sun50i-h616.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
&mmc2 {
pinctrl-names = "default";
@@ -6,6 +6,7 @@
/dts-v1/;
#include "sun50i-h616.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -53,6 +54,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&ehci1 {
status = "okay";
};
@@ -6,12 +6,17 @@
/dts-v1/;
#include "sun50i-h616-orangepi-zero.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
/ {
model = "OrangePi Zero3";
compatible = "xunlong,orangepi-zero3", "allwinner,sun50i-h618";
};
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&emac0 {
allwinner,tx-delay-ps = <700>;
phy-mode = "rgmii-rxid";
@@ -6,6 +6,7 @@
/dts-v1/;
#include "sun50i-h616.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -41,7 +42,7 @@
regulator-always-on;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rtc CLK_OSC32K_FANOUT>;
clock-names = "ext_clock";
@@ -51,6 +52,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
&ehci0 {
status = "okay";
};
@@ -42,7 +42,7 @@
regulator-always-on;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
post-power-on-delay-ms = <200>;
new file mode 100644
@@ -0,0 +1,327 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2024 Ryan Walklin <ryan@testtoast.com>.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Anbernic RG35XX 2024";
+ chassis-type = "handset";
+ compatible = "anbernic,rg35xx-2024", "allwinner,sun50i-h700";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys_gamepad: gpio-keys-gamepad {
+ compatible = "gpio-keys";
+
+ button-a {
+ label = "Action-Pad A";
+ gpios = <&pio 0 0 GPIO_ACTIVE_LOW>; /* PA0 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_EAST>;
+ };
+
+ button-b {
+ label = "Action-Pad B";
+ gpios = <&pio 0 1 GPIO_ACTIVE_LOW>; /* PA1 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_SOUTH>;
+ };
+
+ button-down {
+ label = "D-Pad Down";
+ gpios = <&pio 4 0 GPIO_ACTIVE_LOW>; /* PE0 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_DPAD_DOWN>;
+ };
+
+ button-l1 {
+ label = "Key L1";
+ gpios = <&pio 0 10 GPIO_ACTIVE_LOW>; /* PA10 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_TL>;
+ };
+
+ button-l2 {
+ label = "Key L2";
+ gpios = <&pio 0 11 GPIO_ACTIVE_LOW>; /* PA11 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_TL2>;
+ };
+
+ button-left {
+ label = "D-Pad left";
+ gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_DPAD_LEFT>;
+ };
+
+ button-menu {
+ label = "Key Menu";
+ gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_MODE>;
+ };
+
+ button-r1 {
+ label = "Key R1";
+ gpios = <&pio 0 12 GPIO_ACTIVE_LOW>; /* PA12 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_TR>;
+ };
+
+ button-r2 {
+ label = "Key R2";
+ gpios = <&pio 0 7 GPIO_ACTIVE_LOW>; /* PA7 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_TR2>;
+ };
+
+ button-right {
+ label = "D-Pad Right";
+ gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_DPAD_RIGHT>;
+ };
+
+ button-select {
+ label = "Key Select";
+ gpios = <&pio 0 5 GPIO_ACTIVE_LOW>; /* PA5 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_SELECT>;
+ };
+ button-start {
+ label = "Key Start";
+ gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_START>;
+ };
+
+ button-up {
+ label = "D-Pad Up";
+ gpios = <&pio 0 6 GPIO_ACTIVE_LOW>; /* PA6 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_DPAD_UP>;
+ };
+
+ button-x {
+ label = "Action-Pad X";
+ gpios = <&pio 0 3 GPIO_ACTIVE_LOW>; /* PA3 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_NORTH>;
+ };
+
+ button-y {
+ label = "Action Pad Y";
+ gpios = <&pio 0 2 GPIO_ACTIVE_LOW>; /* PA2 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_WEST>;
+ };
+ };
+
+ gpio-keys-volume {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ button-vol-up {
+ label = "Key Volume Up";
+ gpios = <&pio 4 1 GPIO_ACTIVE_LOW>; /* PE1 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ button-vol-down {
+ label = "Key Volume Down";
+ gpios = <&pio 4 2 GPIO_ACTIVE_LOW>; /* PE2 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 8 12 GPIO_ACTIVE_HIGH>; /* PI12 */
+ default-state = "on";
+ };
+ };
+
+ reg_vcc5v: regulator-vcc5v { /* USB-C power input */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc1>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_cldo3>;
+ disable-wp;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ vcc-pa-supply = <®_cldo3>;
+ vcc-pc-supply = <®_cldo3>;
+ vcc-pe-supply = <®_cldo3>;
+ vcc-pf-supply = <®_cldo3>;
+ vcc-pg-supply = <®_aldo4>;
+ vcc-ph-supply = <®_cldo3>;
+ vcc-pi-supply = <®_cldo3>;
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp717: pmic@3a3 {
+ compatible = "x-powers,axp717";
+ reg = <0x3a3>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ vin1-supply = <®_vcc5v>;
+ vin2-supply = <®_vcc5v>;
+ vin3-supply = <®_vcc5v>;
+ vin4-supply = <®_vcc5v>;
+
+ regulators {
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <940000>;
+ regulator-max-microvolt = <940000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-dram";
+ };
+
+ reg_aldo1: aldo1 {
+ /* 1.8v - unused */
+ };
+
+ reg_aldo2: aldo2 {
+ /* 1.8v - unused */
+ };
+
+ reg_aldo3: aldo3 {
+ /* 1.8v - unused */
+ };
+
+ reg_aldo4: aldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pg";
+ };
+
+ reg_bldo1: bldo1 {
+ /* 1.8v - unused */
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pll";
+ };
+
+ reg_bldo3: bldo3 {
+ /* 2.8v - unused */
+ };
+
+ reg_bldo4: bldo4 {
+ /* 1.2v - unused */
+ };
+
+ reg_cldo1: cldo1 {
+ /* 3.3v - audio codec - not yet implemented */
+ };
+
+ reg_cldo2: cldo2 {
+ /* 3.3v - unused */
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-io";
+ };
+
+ reg_cldo4: cldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ };
+
+ reg_boost: boost {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5200000>;
+ regulator-name = "boost";
+ };
+
+ reg_cpusldo: cpusldo {
+ /* unused */
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+/* the AXP717 has USB type-C role switch functionality, not yet described by the binding */
+&usbotg {
+ dr_mode = "peripheral"; /* USB type-C receptable */
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2024 Ryan Walklin <ryan@testtoast.com>.
+ * Copyright (C) 2024 Chris Morgan <macroalpha82@gmail.com>.
+ */
+
+#include "sun50i-h700-anbernic-rg35xx-plus.dts"
+
+/ {
+ model = "Anbernic RG35XX H";
+ compatible = "anbernic,rg35xx-h", "allwinner,sun50i-h700";
+};
+
+&gpio_keys_gamepad {
+ button-thumbl {
+ label = "GPIO Thumb Left";
+ gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_THUMBL>;
+ };
+
+ button-thumbr {
+ label = "GPIO Thumb Right";
+ gpios = <&pio 4 9 GPIO_ACTIVE_LOW>; /* PE9 */
+ linux,input-type = <EV_KEY>;
+ linux,code = <BTN_THUMBR>;
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2024 Ryan Walklin <ryan@testtoast.com>.
+ */
+
+#include "sun50i-h700-anbernic-rg35xx-2024.dts"
+
+/ {
+ model = "Anbernic RG35XX Plus";
+ compatible = "anbernic,rg35xx-plus", "allwinner,sun50i-h700";
+
+ wifi_pwrseq: pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc CLK_OSC32K_FANOUT>;
+ clock-names = "ext_clock";
+ pinctrl-0 = <&x32clk_fanout_pin>;
+ pinctrl-names = "default";
+ post-power-on-delay-ms = <200>;
+ reset-gpios = <&pio 6 18 GPIO_ACTIVE_LOW>; /* PG18 */
+ };
+};
+
+/* SDIO WiFi RTL8821CS */
+&mmc1 {
+ vmmc-supply = <®_cldo4>;
+ vqmmc-supply = <®_aldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ sdio_wifi: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 15 IRQ_TYPE_LEVEL_LOW>; /* PG15 */
+ interrupt-names = "host-wake";
+ };
+};
+
+/* Bluetooth RTL8821CS */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "realtek,rtl8821cs-bt", "realtek,rtl8723bs-bt";
+ device-wake-gpios = <&pio 6 17 GPIO_ACTIVE_HIGH>; /* PG17 */
+ enable-gpios = <&pio 6 19 GPIO_ACTIVE_HIGH>; /* PG19 */
+ host-wake-gpios = <&pio 6 16 GPIO_ACTIVE_HIGH>; /* PG16 */
+ };
+};
@@ -62,14 +62,14 @@
};
trips {
- cpu_alert0: cpu_alert0 {
+ cpu_alert0: cpu-alert0 {
/* milliCelsius */
temperature = <85000>;
hysteresis = <2000>;
type = "passive";
};
- cpu_crit: cpu_crit {
+ cpu_crit: cpu-crit {
/* milliCelsius */
temperature = <100000>;
hysteresis = <2000>;
@@ -77,7 +77,7 @@
};
};
- mmc0_pwrseq: mmc0_pwrseq {
+ mmc0_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
};
@@ -77,7 +77,7 @@
};
};
- mmc0_pwrseq: mmc0_pwrseq {
+ mmc0_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
};
@@ -109,7 +109,7 @@
};
};
- reg_vga_3v3: vga_3v3_regulator {
+ reg_vga_3v3: vga-3v3-regulator {
compatible = "regulator-fixed";
regulator-name = "vga-3v3";
regulator-min-microvolt = <3300000>;
@@ -119,7 +119,7 @@
gpio = <&pio 7 25 GPIO_ACTIVE_HIGH>; /* PH25 */
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
};
@@ -179,14 +179,14 @@
};
trips {
- cpu_alert0: cpu_alert0 {
+ cpu_alert0: cpu-alert0 {
/* milliCelsius */
temperature = <70000>;
hysteresis = <2000>;
type = "passive";
};
- cpu_crit: cpu_crit {
+ cpu_crit: cpu-crit {
/* milliCelsius */
temperature = <100000>;
hysteresis = <2000>;
@@ -1315,7 +1315,7 @@
compatible = "allwinner,sun6i-a31-prcm";
reg = <0x01f01400 0x200>;
- ar100: ar100_clk {
+ ar100: ar100-clk {
compatible = "allwinner,sun6i-a31-ar100-clk";
#clock-cells = <0>;
clocks = <&rtc CLK_OSC32K>, <&osc24M>,
@@ -1324,7 +1324,7 @@
clock-output-names = "ar100";
};
- ahb0: ahb0_clk {
+ ahb0: ahb0-clk {
compatible = "fixed-factor-clock";
#clock-cells = <0>;
clock-div = <1>;
@@ -1333,14 +1333,14 @@
clock-output-names = "ahb0";
};
- apb0: apb0_clk {
+ apb0: apb0-clk {
compatible = "allwinner,sun6i-a31-apb0-clk";
#clock-cells = <0>;
clocks = <&ahb0>;
clock-output-names = "apb0";
};
- apb0_gates: apb0_gates_clk {
+ apb0_gates: apb0-gates-clk {
compatible = "allwinner,sun6i-a31-apb0-gates-clk";
#clock-cells = <1>;
clocks = <&apb0>;
@@ -1350,14 +1350,14 @@
"apb0_i2c";
};
- ir_clk: ir_clk {
+ ir_clk: ir-clk {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
clocks = <&rtc CLK_OSC32K>, <&osc24M>;
clock-output-names = "ir";
};
- apb0_rst: apb0_rst {
+ apb0_rst: apb0-rst {
compatible = "allwinner,sun6i-a31-clock-reset";
#reset-cells = <1>;
};
@@ -75,7 +75,7 @@
};
};
- mmc2_pwrseq: mmc2_pwrseq {
+ mmc2_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 WIFI_EN */
};
@@ -86,7 +86,7 @@
};
};
- mmc3_pwrseq: mmc3_pwrseq {
+ mmc3_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
};
@@ -96,7 +96,7 @@
};
};
- mmc3_pwrseq: mmc3_pwrseq {
+ mmc3_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
clocks = <&ccu CLK_OUT_A>;
@@ -65,7 +65,7 @@
stdout-path = "serial0:115200n8";
};
- reg_mmc3_vdd: mmc3_vdd {
+ reg_mmc3_vdd: regulator-mmc3-vdd {
compatible = "regulator-fixed";
regulator-name = "mmc3_vdd";
regulator-min-microvolt = <3000000>;
@@ -74,7 +74,7 @@
gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
};
- reg_gmac_vdd: gmac_vdd {
+ reg_gmac_vdd: regulator-gmac-vdd {
compatible = "regulator-fixed";
regulator-name = "gmac_vdd";
regulator-min-microvolt = <3000000>;
@@ -14,7 +14,7 @@
model = "Olimex A20-Olimex-SOM-EVB-eMMC";
compatible = "olimex,a20-olimex-som-evb-emmc", "allwinner,sun7i-a20";
- mmc2_pwrseq: mmc2_pwrseq {
+ mmc2_pwrseq: pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&pio 2 18 GPIO_ACTIVE_LOW>;
};
@@ -13,7 +13,7 @@
model = "Olimex A20-SOM204-EVB-eMMC";
compatible = "olimex,a20-olimex-som204-evb-emmc", "allwinner,sun7i-a20";
- mmc2_pwrseq: mmc2_pwrseq {
+ mmc2_pwrseq: pwrseq-1 {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&pio 2 16 GPIO_ACTIVE_LOW>;
};
@@ -65,7 +65,7 @@
};
};
- rtl_pwrseq: rtl_pwrseq {
+ rtl_pwrseq: pwrseq-0 {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 6 9 GPIO_ACTIVE_LOW>;
};
@@ -177,7 +177,7 @@
non-removable;
status = "okay";
- rtl8723bs: sdio_wifi@1 {
+ rtl8723bs: wifi@1 {
reg = <1>;
};
};
@@ -82,7 +82,7 @@
};
};
- reg_axp_ipsout: axp_ipsout {
+ reg_axp_ipsout: regulator-axp-ipsout {
compatible = "regulator-fixed";
regulator-name = "axp-ipsout";
regulator-min-microvolt = <5000000>;
@@ -60,7 +60,7 @@
stdout-path = "serial0:115200n8";
};
- mmc3_pwrseq: mmc3_pwrseq {
+ mmc3_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
};
@@ -153,14 +153,14 @@
};
trips {
- cpu_alert0: cpu_alert0 {
+ cpu_alert0: cpu-alert0 {
/* milliCelsius */
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
- cpu_crit: cpu_crit {
+ cpu_crit: cpu-crit {
/* milliCelsius */
temperature = <100000>;
hysteresis = <2000>;
@@ -108,7 +108,7 @@
#size-cells = <1>;
ranges;
- osc24M: osc24M_clk {
+ osc24M: osc24M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
@@ -116,7 +116,7 @@
clock-output-names = "osc24M";
};
- ext_osc32k: ext_osc32k_clk {
+ ext_osc32k: ext-osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -730,7 +730,7 @@
compatible = "allwinner,sun8i-a23-prcm";
reg = <0x01f01400 0x200>;
- ar100: ar100_clk {
+ ar100: ar100-clk {
compatible = "fixed-factor-clock";
#clock-cells = <0>;
clock-div = <1>;
@@ -739,7 +739,7 @@
clock-output-names = "ar100";
};
- ahb0: ahb0_clk {
+ ahb0: ahb0-clk {
compatible = "fixed-factor-clock";
#clock-cells = <0>;
clock-div = <1>;
@@ -748,14 +748,14 @@
clock-output-names = "ahb0";
};
- apb0: apb0_clk {
+ apb0: apb0-clk {
compatible = "allwinner,sun8i-a23-apb0-clk";
#clock-cells = <0>;
clocks = <&ahb0>;
clock-output-names = "apb0";
};
- apb0_gates: apb0_gates_clk {
+ apb0_gates: apb0-gates-clk {
compatible = "allwinner,sun8i-a23-apb0-gates-clk";
#clock-cells = <1>;
clocks = <&apb0>;
@@ -764,7 +764,7 @@
"apb0_i2c";
};
- apb0_rst: apb0_rst {
+ apb0_rst: apb0-rst {
compatible = "allwinner,sun6i-a31-clock-reset";
#reset-cells = <1>;
};
@@ -52,7 +52,7 @@
ethernet0 = &esp8089;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
/* The esp8089 needs 200 ms after driving wifi-en high */
@@ -76,7 +76,7 @@
non-removable;
status = "okay";
- esp8089: sdio_wifi@1 {
+ esp8089: wifi@1 {
compatible = "esp,esp8089";
reg = <1>;
esp,crystal-26M-en = <2>;
@@ -52,7 +52,7 @@
ethernet0 = &esp8089;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
/* The esp8089 needs 200 ms after driving wifi-en high */
@@ -69,7 +69,7 @@
non-removable;
status = "okay";
- esp8089: sdio_wifi@1 {
+ esp8089: wifi@1 {
compatible = "esp,esp8089";
reg = <1>;
esp,crystal-26M-en = <2>;
@@ -85,7 +85,7 @@
non-removable;
status = "okay";
- rtl8703as: sdio_wifi@1 {
+ rtl8703as: wifi@1 {
reg = <1>;
};
};
@@ -78,7 +78,7 @@
non-removable;
status = "okay";
- rtl8723bs: sdio_wifi@1 {
+ rtl8723bs: wifi@1 {
reg = <1>;
};
};
@@ -323,35 +323,35 @@
};
trips {
- cpu_alert0: cpu_alert0 {
+ cpu_alert0: cpu-alert0 {
/* milliCelsius */
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
- gpu_alert0: gpu_alert0 {
+ gpu_alert0: gpu-alert0 {
/* milliCelsius */
temperature = <85000>;
hysteresis = <2000>;
type = "passive";
};
- cpu_alert1: cpu_alert1 {
+ cpu_alert1: cpu-alert1 {
/* milliCelsius */
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
- gpu_alert1: gpu_alert1 {
+ gpu_alert1: gpu-alert1 {
/* milliCelsius */
temperature = <95000>;
hysteresis = <2000>;
type = "hot";
};
- cpu_crit: cpu_crit {
+ cpu_crit: cpu-crit {
/* milliCelsius */
temperature = <110000>;
hysteresis = <2000>;
@@ -95,7 +95,7 @@
gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&ac100_rtc 1>;
clock-names = "ext_clock";
@@ -144,7 +144,7 @@
compatible = "linux,spdif-dit";
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&ac100_rtc 1>;
clock-names = "ext_clock";
@@ -123,7 +123,7 @@
vin-supply = <®_vbat>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
@@ -164,7 +164,7 @@
ranges;
/* TODO: PRCM block has a mux for this. */
- osc24M: osc24M_clk {
+ osc24M: osc24M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
@@ -177,14 +177,14 @@
* It is an internal RC-based oscillator.
* TODO: Its controls are in the PRCM block.
*/
- osc16M: osc16M_clk {
+ osc16M: osc16M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <16000000>;
clock-output-names = "osc16M";
};
- osc16Md512: osc16Md512_clk {
+ osc16Md512: osc16Md512-clk {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clock-div = <512>;
@@ -1126,7 +1126,7 @@
#reset-cells = <1>;
};
- r_cpucfg@1f01c00 {
+ cpucfg@1f01c00 {
compatible = "allwinner,sun8i-a83t-r-cpucfg";
reg = <0x1f01c00 0x400>;
};
@@ -103,7 +103,7 @@
cpu-supply = <®_vcc1v2>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -43,11 +43,12 @@
/* Orange Pi R1 is based on Orange Pi Zero design */
#include "sun8i-h2-plus-orangepi-zero.dts"
+/delete-node/ ®_vcc_wifi;
+
/ {
model = "Xunlong Orange Pi R1";
compatible = "xunlong,orangepi-r1", "allwinner,sun8i-h2-plus";
- /delete-node/ reg_vcc_wifi;
/*
* Ths pin of this regulator is the same with the Wi-Fi extra
@@ -89,7 +90,7 @@
vmmc-supply = <®_vcc3v3>;
vqmmc-supply = <®_vcc3v3>;
- rtl8189etv: sdio_wifi@1 {
+ rtl8189etv: wifi@1 {
reg = <1>;
};
};
@@ -80,7 +80,7 @@
};
};
- reg_vcc_wifi: reg_vcc_wifi {
+ reg_vcc_wifi: reg-vcc-wifi {
compatible = "regulator-fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
@@ -105,7 +105,7 @@
states = <1100000 0>, <1300000 1>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
post-power-on-delay-ms = <200>;
@@ -149,7 +149,7 @@
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
- xr819: sdio_wifi@1 {
+ xr819: wifi@1 {
reg = <1>;
};
};
@@ -122,7 +122,7 @@
compatible = "linux,spdif-dit";
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -185,7 +185,7 @@
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
- sdiowifi: sdio_wifi@1 {
+ sdiowifi: wifi@1 {
reg = <1>;
};
};
@@ -87,7 +87,7 @@
vin-supply = <®_vcc5v0>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -119,7 +119,7 @@
non-removable;
status = "okay";
- sdio_wifi: sdio_wifi@1 {
+ sdio_wifi: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
@@ -62,7 +62,7 @@
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
@@ -132,7 +132,7 @@
non-removable;
status = "okay";
- sdio_wifi: sdio_wifi@1 {
+ sdio_wifi: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
@@ -73,7 +73,7 @@
};
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
@@ -43,7 +43,7 @@
<1300000 0x1>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -105,7 +105,7 @@
};
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
};
@@ -169,7 +169,7 @@
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
- rtl8189: sdio_wifi@1 {
+ rtl8189: wifi@1 {
reg = <1>;
};
};
@@ -143,7 +143,7 @@
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
- rtl8189ftv: sdio_wifi@1 {
+ rtl8189ftv: wifi@1 {
reg = <1>;
};
};
@@ -63,7 +63,7 @@
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
- rtl8189ftv: sdio_wifi@1 {
+ rtl8189ftv: wifi@1 {
reg = <1>;
};
};
@@ -92,7 +92,7 @@
regulator-max-microvolt = <3300000>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
post-power-on-delay-ms = <200>;
@@ -62,7 +62,7 @@
};
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
/*
* Q8 boards use various PL# pins as wifi-en. On other boards
@@ -94,7 +94,7 @@
non-removable;
status = "okay";
- sdio_wifi: sdio_wifi@1 {
+ sdio_wifi: wifi@1 {
reg = <1>;
};
};
@@ -88,7 +88,7 @@
regulator-max-microvolt = <5000000>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -75,7 +75,7 @@
};
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
};
@@ -100,7 +100,7 @@
enable-active-high;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
clocks = <&ccu CLK_OUTA>;
@@ -62,7 +62,7 @@
regulator-max-microvolt = <5000000>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; // PB10 WIFI_EN
clocks = <&ccu CLK_OUTA>;
@@ -51,7 +51,7 @@
startup-delay-us = <200000>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
post-power-on-delay-ms = <200>;
@@ -98,7 +98,7 @@
#size-cells = <1>;
ranges;
- osc24M: osc24M_clk {
+ osc24M: osc24M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
@@ -106,7 +106,7 @@
clock-output-names = "osc24M";
};
- osc32k: osc32k_clk {
+ osc32k: osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
@@ -94,7 +94,7 @@
enable-active-high;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
clocks = <&ccu CLK_OUTA>;
@@ -196,14 +196,14 @@
* The actual TX clock rate is not controlled by the
* gmac_tx clock.
*/
- mii_phy_tx_clk: mii_phy_tx_clk {
+ mii_phy_tx_clk: mii-phy-tx-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
clock-output-names = "mii_phy_tx";
};
- gmac_int_tx_clk: gmac_int_tx_clk {
+ gmac_int_tx_clk: gmac-int-tx-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <125000000>;
@@ -98,7 +98,7 @@
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
clocks = <&rtc CLK_OSC32K_FANOUT>;
@@ -18,7 +18,7 @@
stdout-path = "serial0:115200n8";
};
- wifi_pwrseq: wifi_pwrseq {
+ wifi_pwrseq: pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
post-power-on-delay-ms = <200>;
@@ -83,7 +83,7 @@
#size-cells = <1>;
ranges;
- osc24M: osc24M_clk {
+ osc24M: osc24M-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
@@ -91,7 +91,7 @@
clock-output-names = "osc24M";
};
- osc32k: osc32k_clk {
+ osc32k: osc32k-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
Sync the devicetree files from the official Linux kernel tree, v6.10. This is covering Allwinner SoCs with 32-bit and 64-bit ARM cores. Besides mostly cosmectic changes, this adds cpufreq support to H616 boards, Nothing that U-Boot needs for itself, but helpful to pass on to kernels. We also get the .dts files for the Tanix TX1 TV box and three Anbernic handheld gaming devices. As before, this omits the non-backwards compatible changes to the R_INTC controller, to remain compatible with older kernels. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm/dts/sun50i-a64-bananapi-m64.dts | 2 +- arch/arm/dts/sun50i-a64-nanopi-a64.dts | 2 +- arch/arm/dts/sun50i-a64-olinuxino.dts | 2 +- arch/arm/dts/sun50i-a64-orangepi-win.dts | 2 +- arch/arm/dts/sun50i-a64-pinebook.dts | 2 +- arch/arm/dts/sun50i-a64-pinephone.dtsi | 16 +- arch/arm/dts/sun50i-a64-pinetab.dts | 2 +- arch/arm/dts/sun50i-a64-teres-i.dts | 2 +- arch/arm/dts/sun50i-a64.dtsi | 18 +- arch/arm/dts/sun50i-h313-tanix-tx1.dts | 183 ++++++++++ arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts | 2 +- arch/arm/dts/sun50i-h5-nanopi-r1s-h5.dts | 4 +- arch/arm/dts/sun50i-h5-orangepi-prime.dts | 2 +- arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts | 2 +- .../arm/dts/sun50i-h5-orangepi-zero-plus2.dts | 2 +- arch/arm/dts/sun50i-h6-beelink-gs1.dts | 2 +- arch/arm/dts/sun50i-h6-orangepi-3.dts | 2 +- arch/arm/dts/sun50i-h6-orangepi-lite2.dts | 2 +- arch/arm/dts/sun50i-h6-orangepi.dtsi | 2 +- arch/arm/dts/sun50i-h6-pine-h64-model-b.dts | 6 +- arch/arm/dts/sun50i-h6-pine-h64.dts | 2 +- arch/arm/dts/sun50i-h6.dtsi | 2 +- arch/arm/dts/sun50i-h616-bigtreetech-cb1.dtsi | 5 + arch/arm/dts/sun50i-h616-cpu-opp.dtsi | 115 ++++++ arch/arm/dts/sun50i-h616-orangepi-zero2.dts | 5 + arch/arm/dts/sun50i-h616-x96-mate.dts | 5 + arch/arm/dts/sun50i-h616.dtsi | 19 +- .../arm/dts/sun50i-h618-longan-module-3h.dtsi | 5 + arch/arm/dts/sun50i-h618-orangepi-zero2w.dts | 5 + arch/arm/dts/sun50i-h618-orangepi-zero3.dts | 5 + .../arm/dts/sun50i-h618-transpeed-8k618-t.dts | 7 +- arch/arm/dts/sun50i-h64-remix-mini-pc.dts | 2 +- .../dts/sun50i-h700-anbernic-rg35xx-2024.dts | 327 ++++++++++++++++++ .../arm/dts/sun50i-h700-anbernic-rg35xx-h.dts | 36 ++ .../dts/sun50i-h700-anbernic-rg35xx-plus.dts | 53 +++ arch/arm/dts/sun5i-a13.dtsi | 4 +- arch/arm/dts/sun5i-gr8-chip-pro.dts | 2 +- arch/arm/dts/sun5i-r8-chip.dts | 2 +- arch/arm/dts/sun6i-a31-hummingbird.dts | 4 +- arch/arm/dts/sun6i-a31.dtsi | 16 +- arch/arm/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 2 +- arch/arm/dts/sun7i-a20-bananapi-m1-plus.dts | 2 +- arch/arm/dts/sun7i-a20-cubietruck.dts | 2 +- arch/arm/dts/sun7i-a20-hummingbird.dts | 4 +- .../arm/dts/sun7i-a20-olimex-som-evb-emmc.dts | 2 +- .../dts/sun7i-a20-olimex-som204-evb-emmc.dts | 2 +- arch/arm/dts/sun7i-a20-olimex-som204-evb.dts | 4 +- arch/arm/dts/sun7i-a20-olinuxino-lime2.dts | 2 +- arch/arm/dts/sun7i-a20-wits-pro-a20-dkt.dts | 2 +- arch/arm/dts/sun7i-a20.dtsi | 4 +- arch/arm/dts/sun8i-a23-a33.dtsi | 14 +- .../dts/sun8i-a23-polaroid-mid2407pxe03.dts | 4 +- .../dts/sun8i-a23-polaroid-mid2809pxe04.dts | 4 +- arch/arm/dts/sun8i-a33-ga10h-v1.1.dts | 2 +- arch/arm/dts/sun8i-a33-inet-d978-rev2.dts | 2 +- arch/arm/dts/sun8i-a33.dtsi | 10 +- arch/arm/dts/sun8i-a83t-bananapi-m3.dts | 2 +- arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 2 +- arch/arm/dts/sun8i-a83t-tbs-a711.dts | 2 +- arch/arm/dts/sun8i-a83t.dtsi | 8 +- .../dts/sun8i-h2-plus-bananapi-m2-zero.dts | 2 +- arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts | 5 +- arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts | 6 +- arch/arm/dts/sun8i-h3-beelink-x2.dts | 4 +- arch/arm/dts/sun8i-h3-nanopi-duo2.dts | 4 +- arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts | 4 +- arch/arm/dts/sun8i-h3-nanopi-neo-air.dts | 2 +- arch/arm/dts/sun8i-h3-nanopi-r1.dts | 2 +- arch/arm/dts/sun8i-h3-orangepi-2.dts | 4 +- arch/arm/dts/sun8i-h3-orangepi-lite.dts | 2 +- arch/arm/dts/sun8i-h3-orangepi-pc-plus.dts | 2 +- arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts | 2 +- arch/arm/dts/sun8i-q8-common.dtsi | 4 +- arch/arm/dts/sun8i-r16-bananapi-m2m.dts | 2 +- arch/arm/dts/sun8i-r16-parrot.dts | 2 +- arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts | 2 +- arch/arm/dts/sun8i-r40-oka40i-c.dts | 2 +- arch/arm/dts/sun8i-s3-pinecube.dts | 2 +- arch/arm/dts/sun8i-v3s.dtsi | 4 +- arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts | 2 +- arch/arm/dts/sun9i-a80.dtsi | 4 +- arch/arm/dts/sunxi-bananapi-m2-plus.dtsi | 2 +- arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi | 2 +- arch/arm/dts/sunxi-h3-h5.dtsi | 4 +- 84 files changed, 897 insertions(+), 128 deletions(-) create mode 100644 arch/arm/dts/sun50i-h313-tanix-tx1.dts create mode 100644 arch/arm/dts/sun50i-h616-cpu-opp.dtsi create mode 100644 arch/arm/dts/sun50i-h700-anbernic-rg35xx-2024.dts create mode 100644 arch/arm/dts/sun50i-h700-anbernic-rg35xx-h.dts create mode 100644 arch/arm/dts/sun50i-h700-anbernic-rg35xx-plus.dts