@@ -612,6 +612,12 @@ config VIDEO_LCD_HITACHI_TX18D42VM
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
+config VIDEO_LCD_NEWVISION_NV3052C
+ bool "NewVision NV3052C RGB/SPI panel support"
+ select VIDEO_MIPI_DBI
+ ---help---
+ Support for panels built around the NewVision NV3052C controller.
+
config VIDEO_LCD_SPI_CS
string "SPI CS pin for LCD related config job"
depends on VIDEO_LCD_SSD2828 || VIDEO_LCD_HITACHI_TX18D42VM
@@ -66,6 +66,7 @@ obj-$(CONFIG_VIDEO_LCD_RENESAS_R69328) += renesas-r69328.o
obj-$(CONFIG_VIDEO_LCD_SAMSUNG_LTL106HL02) += samsung-ltl106hl02.o
obj-$(CONFIG_VIDEO_LCD_SSD2828) += ssd2828.o
obj-$(CONFIG_VIDEO_LCD_TDO_TL070WSH30) += tdo-tl070wsh30.o
+obj-$(CONFIG_VIDEO_LCD_NEWVISION_NV3052C) += newvision-nv3052c.o
obj-$(CONFIG_VIDEO_MCDE_SIMPLE) += mcde_simple.o
obj-${CONFIG_VIDEO_MESON} += meson/
obj-${CONFIG_VIDEO_MIPI_DSI} += mipi_dsi.o
new file mode 100644
@@ -0,0 +1,608 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * NewVision NV3052C IPS LCD panel driver
+ *
+ * Copyright (C) 2020, Paul Cercueil <paul@crapouillou.net>
+ * Copyright (C) 2022, Christophe Branchereau <cbranchereau@gmail.com>
+ */
+
+#include <asm/gpio.h>
+#include <backlight.h>
+#include <dm/device_compat.h>
+#include <dm.h>
+#include <linux/delay.h>
+#include <mipi_dbi.h>
+#include <panel.h>
+#include <power/regulator.h>
+
+struct nv3052c_reg {
+ u8 cmd;
+ u8 val;
+};
+
+struct nv3052c_panel_info {
+ struct display_timing default_timing;
+ const struct nv3052c_reg *panel_regs;
+ unsigned int panel_regs_len;
+};
+
+struct nv3052c {
+ const struct nv3052c_panel_info *panel_info;
+ struct udevice *supply;
+ struct gpio_desc reset_gpio;
+ struct udevice *backlight;
+ struct spi_slave *spi;
+ struct mipi_dbi dbi;
+};
+
+static const struct nv3052c_reg ltk035c5444t_panel_regs[] = {
+ // EXTC Command set enable, select page 1
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x01 },
+ // Mostly unknown registers
+ { 0xe3, 0x00 },
+ { 0x40, 0x00 },
+ { 0x03, 0x40 },
+ { 0x04, 0x00 },
+ { 0x05, 0x03 },
+ { 0x08, 0x00 },
+ { 0x09, 0x07 },
+ { 0x0a, 0x01 },
+ { 0x0b, 0x32 },
+ { 0x0c, 0x32 },
+ { 0x0d, 0x0b },
+ { 0x0e, 0x00 },
+ { 0x23, 0xa0 },
+ { 0x24, 0x0c },
+ { 0x25, 0x06 },
+ { 0x26, 0x14 },
+ { 0x27, 0x14 },
+ { 0x38, 0xcc }, // VCOM_ADJ1
+ { 0x39, 0xd7 }, // VCOM_ADJ2
+ { 0x3a, 0x4a }, // VCOM_ADJ3
+ { 0x28, 0x40 },
+ { 0x29, 0x01 },
+ { 0x2a, 0xdf },
+ { 0x49, 0x3c },
+ { 0x91, 0x77 }, // EXTPW_CTRL2
+ { 0x92, 0x77 }, // EXTPW_CTRL3
+ { 0xa0, 0x55 },
+ { 0xa1, 0x50 },
+ { 0xa4, 0x9c },
+ { 0xa7, 0x02 },
+ { 0xa8, 0x01 },
+ { 0xa9, 0x01 },
+ { 0xaa, 0xfc },
+ { 0xab, 0x28 },
+ { 0xac, 0x06 },
+ { 0xad, 0x06 },
+ { 0xae, 0x06 },
+ { 0xaf, 0x03 },
+ { 0xb0, 0x08 },
+ { 0xb1, 0x26 },
+ { 0xb2, 0x28 },
+ { 0xb3, 0x28 },
+ { 0xb4, 0x33 },
+ { 0xb5, 0x08 },
+ { 0xb6, 0x26 },
+ { 0xb7, 0x08 },
+ { 0xb8, 0x26 },
+ { 0xf0, 0x00 },
+ { 0xf6, 0xc0 },
+ // EXTC Command set enable, select page 2
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
+ // Set gray scale voltage to adjust gamma
+ { 0xb0, 0x0b }, // PGAMVR0
+ { 0xb1, 0x16 }, // PGAMVR1
+ { 0xb2, 0x17 }, // PGAMVR2
+ { 0xb3, 0x2c }, // PGAMVR3
+ { 0xb4, 0x32 }, // PGAMVR4
+ { 0xb5, 0x3b }, // PGAMVR5
+ { 0xb6, 0x29 }, // PGAMPR0
+ { 0xb7, 0x40 }, // PGAMPR1
+ { 0xb8, 0x0d }, // PGAMPK0
+ { 0xb9, 0x05 }, // PGAMPK1
+ { 0xba, 0x12 }, // PGAMPK2
+ { 0xbb, 0x10 }, // PGAMPK3
+ { 0xbc, 0x12 }, // PGAMPK4
+ { 0xbd, 0x15 }, // PGAMPK5
+ { 0xbe, 0x19 }, // PGAMPK6
+ { 0xbf, 0x0e }, // PGAMPK7
+ { 0xc0, 0x16 }, // PGAMPK8
+ { 0xc1, 0x0a }, // PGAMPK9
+ // Set gray scale voltage to adjust gamma
+ { 0xd0, 0x0c }, // NGAMVR0
+ { 0xd1, 0x17 }, // NGAMVR0
+ { 0xd2, 0x14 }, // NGAMVR1
+ { 0xd3, 0x2e }, // NGAMVR2
+ { 0xd4, 0x32 }, // NGAMVR3
+ { 0xd5, 0x3c }, // NGAMVR4
+ { 0xd6, 0x22 }, // NGAMPR0
+ { 0xd7, 0x3d }, // NGAMPR1
+ { 0xd8, 0x0d }, // NGAMPK0
+ { 0xd9, 0x07 }, // NGAMPK1
+ { 0xda, 0x13 }, // NGAMPK2
+ { 0xdb, 0x13 }, // NGAMPK3
+ { 0xdc, 0x11 }, // NGAMPK4
+ { 0xdd, 0x15 }, // NGAMPK5
+ { 0xde, 0x19 }, // NGAMPK6
+ { 0xdf, 0x10 }, // NGAMPK7
+ { 0xe0, 0x17 }, // NGAMPK8
+ { 0xe1, 0x0a }, // NGAMPK9
+ // EXTC Command set enable, select page 3
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x03 },
+ // Set various timing settings
+ { 0x00, 0x2a }, // GIP_VST_1
+ { 0x01, 0x2a }, // GIP_VST_2
+ { 0x02, 0x2a }, // GIP_VST_3
+ { 0x03, 0x2a }, // GIP_VST_4
+ { 0x04, 0x61 }, // GIP_VST_5
+ { 0x05, 0x80 }, // GIP_VST_6
+ { 0x06, 0xc7 }, // GIP_VST_7
+ { 0x07, 0x01 }, // GIP_VST_8
+ { 0x08, 0x03 }, // GIP_VST_9
+ { 0x09, 0x04 }, // GIP_VST_10
+ { 0x70, 0x22 }, // GIP_ECLK1
+ { 0x71, 0x80 }, // GIP_ECLK2
+ { 0x30, 0x2a }, // GIP_CLK_1
+ { 0x31, 0x2a }, // GIP_CLK_2
+ { 0x32, 0x2a }, // GIP_CLK_3
+ { 0x33, 0x2a }, // GIP_CLK_4
+ { 0x34, 0x61 }, // GIP_CLK_5
+ { 0x35, 0xc5 }, // GIP_CLK_6
+ { 0x36, 0x80 }, // GIP_CLK_7
+ { 0x37, 0x23 }, // GIP_CLK_8
+ { 0x40, 0x03 }, // GIP_CLKA_1
+ { 0x41, 0x04 }, // GIP_CLKA_2
+ { 0x42, 0x05 }, // GIP_CLKA_3
+ { 0x43, 0x06 }, // GIP_CLKA_4
+ { 0x44, 0x11 }, // GIP_CLKA_5
+ { 0x45, 0xe8 }, // GIP_CLKA_6
+ { 0x46, 0xe9 }, // GIP_CLKA_7
+ { 0x47, 0x11 }, // GIP_CLKA_8
+ { 0x48, 0xea }, // GIP_CLKA_9
+ { 0x49, 0xeb }, // GIP_CLKA_10
+ { 0x50, 0x07 }, // GIP_CLKB_1
+ { 0x51, 0x08 }, // GIP_CLKB_2
+ { 0x52, 0x09 }, // GIP_CLKB_3
+ { 0x53, 0x0a }, // GIP_CLKB_4
+ { 0x54, 0x11 }, // GIP_CLKB_5
+ { 0x55, 0xec }, // GIP_CLKB_6
+ { 0x56, 0xed }, // GIP_CLKB_7
+ { 0x57, 0x11 }, // GIP_CLKB_8
+ { 0x58, 0xef }, // GIP_CLKB_9
+ { 0x59, 0xf0 }, // GIP_CLKB_10
+ // Map internal GOA signals to GOA output pad
+ { 0xb1, 0x01 }, // PANELD2U2
+ { 0xb4, 0x15 }, // PANELD2U5
+ { 0xb5, 0x16 }, // PANELD2U6
+ { 0xb6, 0x09 }, // PANELD2U7
+ { 0xb7, 0x0f }, // PANELD2U8
+ { 0xb8, 0x0d }, // PANELD2U9
+ { 0xb9, 0x0b }, // PANELD2U10
+ { 0xba, 0x00 }, // PANELD2U11
+ { 0xc7, 0x02 }, // PANELD2U24
+ { 0xca, 0x17 }, // PANELD2U27
+ { 0xcb, 0x18 }, // PANELD2U28
+ { 0xcc, 0x0a }, // PANELD2U29
+ { 0xcd, 0x10 }, // PANELD2U30
+ { 0xce, 0x0e }, // PANELD2U31
+ { 0xcf, 0x0c }, // PANELD2U32
+ { 0xd0, 0x00 }, // PANELD2U33
+ // Map internal GOA signals to GOA output pad
+ { 0x81, 0x00 }, // PANELU2D2
+ { 0x84, 0x15 }, // PANELU2D5
+ { 0x85, 0x16 }, // PANELU2D6
+ { 0x86, 0x10 }, // PANELU2D7
+ { 0x87, 0x0a }, // PANELU2D8
+ { 0x88, 0x0c }, // PANELU2D9
+ { 0x89, 0x0e }, // PANELU2D10
+ { 0x8a, 0x02 }, // PANELU2D11
+ { 0x97, 0x00 }, // PANELU2D24
+ { 0x9a, 0x17 }, // PANELU2D27
+ { 0x9b, 0x18 }, // PANELU2D28
+ { 0x9c, 0x0f }, // PANELU2D29
+ { 0x9d, 0x09 }, // PANELU2D30
+ { 0x9e, 0x0b }, // PANELU2D31
+ { 0x9f, 0x0d }, // PANELU2D32
+ { 0xa0, 0x01 }, // PANELU2D33
+ // EXTC Command set enable, select page 2
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
+ // Unknown registers
+ { 0x01, 0x01 },
+ { 0x02, 0xda },
+ { 0x03, 0xba },
+ { 0x04, 0xa8 },
+ { 0x05, 0x9a },
+ { 0x06, 0x70 },
+ { 0x07, 0xff },
+ { 0x08, 0x91 },
+ { 0x09, 0x90 },
+ { 0x0a, 0xff },
+ { 0x0b, 0x8f },
+ { 0x0c, 0x60 },
+ { 0x0d, 0x58 },
+ { 0x0e, 0x48 },
+ { 0x0f, 0x38 },
+ { 0x10, 0x2b },
+ // EXTC Command set enable, select page 0
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x00 },
+ // Display Access Control
+ { 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
+};
+
+static const struct nv3052c_reg fs035vg158_panel_regs[] = {
+ // EXTC Command set enable, select page 1
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x01 },
+ // Mostly unknown registers
+ { 0xe3, 0x00 },
+ { 0x40, 0x00 },
+ { 0x03, 0x40 },
+ { 0x04, 0x00 },
+ { 0x05, 0x03 },
+ { 0x08, 0x00 },
+ { 0x09, 0x07 },
+ { 0x0a, 0x01 },
+ { 0x0b, 0x32 },
+ { 0x0c, 0x32 },
+ { 0x0d, 0x0b },
+ { 0x0e, 0x00 },
+ { 0x23, 0x20 }, // RGB interface control: DE MODE PCLK-N
+ { 0x24, 0x0c },
+ { 0x25, 0x06 },
+ { 0x26, 0x14 },
+ { 0x27, 0x14 },
+ { 0x38, 0x9c }, //VCOM_ADJ1, different to ltk035c5444t
+ { 0x39, 0xa7 }, //VCOM_ADJ2, different to ltk035c5444t
+ { 0x3a, 0x50 }, //VCOM_ADJ3, different to ltk035c5444t
+ { 0x28, 0x40 },
+ { 0x29, 0x01 },
+ { 0x2a, 0xdf },
+ { 0x49, 0x3c },
+ { 0x91, 0x57 }, //EXTPW_CTRL2, different to ltk035c5444t
+ { 0x92, 0x57 }, //EXTPW_CTRL3, different to ltk035c5444t
+ { 0xa0, 0x55 },
+ { 0xa1, 0x50 },
+ { 0xa4, 0x9c },
+ { 0xa7, 0x02 },
+ { 0xa8, 0x01 },
+ { 0xa9, 0x01 },
+ { 0xaa, 0xfc },
+ { 0xab, 0x28 },
+ { 0xac, 0x06 },
+ { 0xad, 0x06 },
+ { 0xae, 0x06 },
+ { 0xaf, 0x03 },
+ { 0xb0, 0x08 },
+ { 0xb1, 0x26 },
+ { 0xb2, 0x28 },
+ { 0xb3, 0x28 },
+ { 0xb4, 0x03 }, // Unknown, different to ltk035c5444
+ { 0xb5, 0x08 },
+ { 0xb6, 0x26 },
+ { 0xb7, 0x08 },
+ { 0xb8, 0x26 },
+ { 0xf0, 0x00 },
+ { 0xf6, 0xc0 },
+ // EXTC Command set enable, select page 0
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
+ // Set gray scale voltage to adjust gamma
+ { 0xb0, 0x0b }, // PGAMVR0
+ { 0xb1, 0x16 }, // PGAMVR1
+ { 0xb2, 0x17 }, // PGAMVR2
+ { 0xb3, 0x2c }, // PGAMVR3
+ { 0xb4, 0x32 }, // PGAMVR4
+ { 0xb5, 0x3b }, // PGAMVR5
+ { 0xb6, 0x29 }, // PGAMPR0
+ { 0xb7, 0x40 }, // PGAMPR1
+ { 0xb8, 0x0d }, // PGAMPK0
+ { 0xb9, 0x05 }, // PGAMPK1
+ { 0xba, 0x12 }, // PGAMPK2
+ { 0xbb, 0x10 }, // PGAMPK3
+ { 0xbc, 0x12 }, // PGAMPK4
+ { 0xbd, 0x15 }, // PGAMPK5
+ { 0xbe, 0x19 }, // PGAMPK6
+ { 0xbf, 0x0e }, // PGAMPK7
+ { 0xc0, 0x16 }, // PGAMPK8
+ { 0xc1, 0x0a }, // PGAMPK9
+ // Set gray scale voltage to adjust gamma
+ { 0xd0, 0x0c }, // NGAMVR0
+ { 0xd1, 0x17 }, // NGAMVR0
+ { 0xd2, 0x14 }, // NGAMVR1
+ { 0xd3, 0x2e }, // NGAMVR2
+ { 0xd4, 0x32 }, // NGAMVR3
+ { 0xd5, 0x3c }, // NGAMVR4
+ { 0xd6, 0x22 }, // NGAMPR0
+ { 0xd7, 0x3d }, // NGAMPR1
+ { 0xd8, 0x0d }, // NGAMPK0
+ { 0xd9, 0x07 }, // NGAMPK1
+ { 0xda, 0x13 }, // NGAMPK2
+ { 0xdb, 0x13 }, // NGAMPK3
+ { 0xdc, 0x11 }, // NGAMPK4
+ { 0xdd, 0x15 }, // NGAMPK5
+ { 0xde, 0x19 }, // NGAMPK6
+ { 0xdf, 0x10 }, // NGAMPK7
+ { 0xe0, 0x17 }, // NGAMPK8
+ { 0xe1, 0x0a }, // NGAMPK9
+ // EXTC Command set enable, select page 3
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x03 },
+ // Set various timing settings
+ { 0x00, 0x2a }, // GIP_VST_1
+ { 0x01, 0x2a }, // GIP_VST_2
+ { 0x02, 0x2a }, // GIP_VST_3
+ { 0x03, 0x2a }, // GIP_VST_4
+ { 0x04, 0x61 }, // GIP_VST_5
+ { 0x05, 0x80 }, // GIP_VST_6
+ { 0x06, 0xc7 }, // GIP_VST_7
+ { 0x07, 0x01 }, // GIP_VST_8
+ { 0x08, 0x03 }, // GIP_VST_9
+ { 0x09, 0x04 }, // GIP_VST_10
+ { 0x70, 0x22 }, // GIP_ECLK1
+ { 0x71, 0x80 }, // GIP_ECLK2
+ { 0x30, 0x2a }, // GIP_CLK_1
+ { 0x31, 0x2a }, // GIP_CLK_2
+ { 0x32, 0x2a }, // GIP_CLK_3
+ { 0x33, 0x2a }, // GIP_CLK_4
+ { 0x34, 0x61 }, // GIP_CLK_5
+ { 0x35, 0xc5 }, // GIP_CLK_6
+ { 0x36, 0x80 }, // GIP_CLK_7
+ { 0x37, 0x23 }, // GIP_CLK_8
+ { 0x40, 0x03 }, // GIP_CLKA_1
+ { 0x41, 0x04 }, // GIP_CLKA_2
+ { 0x42, 0x05 }, // GIP_CLKA_3
+ { 0x43, 0x06 }, // GIP_CLKA_4
+ { 0x44, 0x11 }, // GIP_CLKA_5
+ { 0x45, 0xe8 }, // GIP_CLKA_6
+ { 0x46, 0xe9 }, // GIP_CLKA_7
+ { 0x47, 0x11 }, // GIP_CLKA_8
+ { 0x48, 0xea }, // GIP_CLKA_9
+ { 0x49, 0xeb }, // GIP_CLKA_10
+ { 0x50, 0x07 }, // GIP_CLKB_1
+ { 0x51, 0x08 }, // GIP_CLKB_2
+ { 0x52, 0x09 }, // GIP_CLKB_3
+ { 0x53, 0x0a }, // GIP_CLKB_4
+ { 0x54, 0x11 }, // GIP_CLKB_5
+ { 0x55, 0xec }, // GIP_CLKB_6
+ { 0x56, 0xed }, // GIP_CLKB_7
+ { 0x57, 0x11 }, // GIP_CLKB_8
+ { 0x58, 0xef }, // GIP_CLKB_9
+ { 0x59, 0xf0 }, // GIP_CLKB_10
+ // Map internal GOA signals to GOA output pad
+ { 0xb1, 0x01 }, // PANELD2U2
+ { 0xb4, 0x15 }, // PANELD2U5
+ { 0xb5, 0x16 }, // PANELD2U6
+ { 0xb6, 0x09 }, // PANELD2U7
+ { 0xb7, 0x0f }, // PANELD2U8
+ { 0xb8, 0x0d }, // PANELD2U9
+ { 0xb9, 0x0b }, // PANELD2U10
+ { 0xba, 0x00 }, // PANELD2U11
+ { 0xc7, 0x02 }, // PANELD2U24
+ { 0xca, 0x17 }, // PANELD2U27
+ { 0xcb, 0x18 }, // PANELD2U28
+ { 0xcc, 0x0a }, // PANELD2U29
+ { 0xcd, 0x10 }, // PANELD2U30
+ { 0xce, 0x0e }, // PANELD2U31
+ { 0xcf, 0x0c }, // PANELD2U32
+ { 0xd0, 0x00 }, // PANELD2U33
+ // Map internal GOA signals to GOA output pad
+ { 0x81, 0x00 }, // PANELU2D2
+ { 0x84, 0x15 }, // PANELU2D5
+ { 0x85, 0x16 }, // PANELU2D6
+ { 0x86, 0x10 }, // PANELU2D7
+ { 0x87, 0x0a }, // PANELU2D8
+ { 0x88, 0x0c }, // PANELU2D9
+ { 0x89, 0x0e }, // PANELU2D10
+ { 0x8a, 0x02 }, // PANELU2D11
+ { 0x97, 0x00 }, // PANELU2D24
+ { 0x9a, 0x17 }, // PANELU2D27
+ { 0x9b, 0x18 }, // PANELU2D28
+ { 0x9c, 0x0f }, // PANELU2D29
+ { 0x9d, 0x09 }, // PANELU2D30
+ { 0x9e, 0x0b }, // PANELU2D31
+ { 0x9f, 0x0d }, // PANELU2D32
+ { 0xa0, 0x01 }, // PANELU2D33
+ // EXTC Command set enable, select page 2
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x02 },
+ // Unknown registers
+ { 0x01, 0x01 },
+ { 0x02, 0xda },
+ { 0x03, 0xba },
+ { 0x04, 0xa8 },
+ { 0x05, 0x9a },
+ { 0x06, 0x70 },
+ { 0x07, 0xff },
+ { 0x08, 0x91 },
+ { 0x09, 0x90 },
+ { 0x0a, 0xff },
+ { 0x0b, 0x8f },
+ { 0x0c, 0x60 },
+ { 0x0d, 0x58 },
+ { 0x0e, 0x48 },
+ { 0x0f, 0x38 },
+ { 0x10, 0x2b },
+ // EXTC Command set enable, select page 0
+ { 0xff, 0x30 }, { 0xff, 0x52 }, { 0xff, 0x00 },
+ // Display Access Control
+ { 0x36, 0x0a }, // bgr = 1, ss = 1, gs = 0
+};
+
+static const struct nv3052c_panel_info ltk035c5444t_panel_info = {
+ .default_timing = {
+ .pixelclock.typ = 24000000,
+ .hactive.typ = 640,
+ .hfront_porch.typ = 96,
+ .hback_porch.typ = 16,
+ .hsync_len.typ = 48,
+ .vactive.typ = 480,
+ .vfront_porch.typ = 5,
+ .vback_porch.typ = 2,
+ .vsync_len.typ = 13,
+ .flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW | DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_NEGEDGE,
+ },
+ .panel_regs = ltk035c5444t_panel_regs,
+ .panel_regs_len = ARRAY_SIZE(ltk035c5444t_panel_regs),
+};
+
+static const struct nv3052c_panel_info fs035vg158_panel_info = {
+ .default_timing = {
+ .pixelclock.typ = 21000000,
+ .hactive.typ = 640,
+ .hfront_porch.typ = 34,
+ .hback_porch.typ = 20,
+ .hsync_len.typ = 4,
+ .vactive.typ = 480,
+ .vfront_porch.typ = 12,
+ .vback_porch.typ = 6,
+ .vsync_len.typ = 4,
+ .flags = DISPLAY_FLAGS_VSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW | DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_NEGEDGE,
+ },
+ .panel_regs = fs035vg158_panel_regs,
+ .panel_regs_len = ARRAY_SIZE(fs035vg158_panel_regs),
+};
+
+static const struct nv3052c_panel_info *panel_infos[] = {
+ <k035c5444t_panel_info,
+ &fs035vg158_panel_info,
+};
+
+static int nv3052c_panel_enable_backlight(struct udevice *dev)
+{
+ struct nv3052c *priv = dev_get_priv(dev);
+ struct mipi_dbi *dbi = &priv->dbi;
+ int err;
+
+ err = mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+ if (err) {
+ dev_err(dev, "Unable to enable display: %d\n", err);
+ return err;
+ }
+
+ if (priv->backlight) {
+ /* Wait for the picture to be ready before enabling backlight */
+ mdelay(120);
+ err = backlight_enable(priv->backlight);
+ }
+
+ return err;
+}
+
+static int nv3052c_panel_get_display_timing(struct udevice *dev,
+ struct display_timing *timing)
+{
+ struct nv3052c *priv = dev_get_priv(dev);
+ const struct nv3052c_panel_info *info = priv->panel_info;
+ const struct display_timing *our_timing = &info->default_timing;
+
+ memcpy(timing, our_timing, sizeof(*our_timing));
+
+ return 0;
+}
+
+static int nv3052c_panel_of_to_plat(struct udevice *dev)
+{
+ struct nv3052c *priv = dev_get_priv(dev);
+ int panel_info_index = dev_get_driver_data(dev);
+ int err;
+
+ priv->spi = dev_get_parent_priv(dev);
+ priv->panel_info = panel_infos[panel_info_index];
+
+ if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+ err = device_get_supply_regulator(dev, "power-supply",
+ &priv->supply);
+ if (err) {
+ dev_err(dev, "Failed to get power supply: %d\n", err);
+ return err;
+ }
+ }
+
+ err = gpio_request_by_name(dev, "reset-gpios", 0, &priv->reset_gpio,
+ GPIOD_IS_OUT);
+ if (err) {
+ dev_err(dev, "Failed to get reset GPIO: %d\n", err);
+ return err;
+ }
+
+ err = uclass_get_device_by_phandle(UCLASS_PANEL_BACKLIGHT, dev,
+ "backlight", &priv->backlight);
+ if (err) {
+ dev_err(dev, "Failed to get backlight: %d\n", err);
+ return err;
+ }
+
+ return 0;
+}
+
+static int nv3052c_panel_probe(struct udevice *dev)
+{
+ struct nv3052c *priv = dev_get_priv(dev);
+ const struct nv3052c_reg *panel_regs = priv->panel_info->panel_regs;
+ unsigned int panel_regs_len = priv->panel_info->panel_regs_len;
+ struct mipi_dbi *dbi = &priv->dbi;
+ unsigned int i;
+ int err;
+
+ err = mipi_dbi_spi_init(priv->spi, &priv->dbi, NULL);
+ if (err) {
+ dev_err(dev, "MPI DBI init failed: %d\n", err);
+ return err;
+ }
+
+ if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+ err = regulator_set_enable(priv->supply, true);
+ if (err) {
+ dev_err(dev, "Failed to enable power supply: %d\n", err);
+ return err;
+ }
+ }
+
+ /* Reset the chip */
+ dm_gpio_set_value(&priv->reset_gpio, true);
+ mdelay(1);
+ dm_gpio_set_value(&priv->reset_gpio, false);
+ mdelay(150);
+
+ for (i = 0; i < panel_regs_len; i++) {
+ err = mipi_dbi_command(dbi, panel_regs[i].cmd,
+ panel_regs[i].val);
+
+ if (err) {
+ dev_err(dev, "Unable to set register: %d\n", err);
+ goto err_disable_regulator;
+ }
+ }
+
+ err = mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+ if (err) {
+ dev_err(dev, "Unable to exit sleep mode: %d\n", err);
+ goto err_disable_regulator;
+ }
+
+ return 0;
+
+err_disable_regulator:
+ if (CONFIG_IS_ENABLED(DM_REGULATOR))
+ regulator_set_enable(priv->supply, false);
+
+ return err;
+}
+
+static const struct panel_ops nv3052c_panel_ops = {
+ .enable_backlight = nv3052c_panel_enable_backlight,
+ .get_display_timing = nv3052c_panel_get_display_timing,
+};
+
+static const struct udevice_id nv3052c_panel_ids[] = {
+ { .compatible = "leadtek,ltk035c5444t", .data = 0 },
+ { .compatible = "fascontek,fs035vg158", .data = 1 },
+ { }
+};
+
+U_BOOT_DRIVER(nv3052c_panel) = {
+ .name = "nv3052c_panel",
+ .id = UCLASS_PANEL,
+ .of_match = nv3052c_panel_ids,
+ .ops = &nv3052c_panel_ops,
+ .of_to_plat = nv3052c_panel_of_to_plat,
+ .probe = nv3052c_panel_probe,
+ .priv_auto = sizeof(struct nv3052c),
+};
This driver is mostly copied from the Linux kernel and includes support for two physical panels that use this driver. Signed-off-by: John Watts <contact@jookia.org> --- This patch is a straightforward port of the kernel NV3052C SPI driver to U-Boot, keeping full compatibility with mainline device tree bindings. --- drivers/video/Kconfig | 6 + drivers/video/Makefile | 1 + drivers/video/newvision-nv3052c.c | 608 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 615 insertions(+) --- base-commit: 0cc0eab0a140b5e660c25a27e116c9be538c1c12 change-id: 20240601-panel_nv3052c-76bab2b2c358 Best regards,