| Message ID | 20230721134606.4505-3-andre.przywara@arm.com |
|---|---|
| State | Superseded |
| Delegated to: | Andre Przywara |
| Headers | show |
| Series | sunxi: Allwinner T113s support | expand |
Hi Andre, Series looks good so far! I'm trying to move my testing build over to it now; I will report back when I've been running on it for a little bit. On 7/21/23 07:45, Andre Przywara wrote: > diff --git a/board/sunxi/board.c b/board/sunxi/board.c > index 7ac50c4ae8c..2db4a2d73ca 100644 > --- a/board/sunxi/board.c > +++ b/board/sunxi/board.c > @@ -187,7 +187,7 @@ enum env_location env_get_location(enum env_operation op, int prio) > /* add board specific code here */ > int board_init(void) > { > - __maybe_unused int id_pfr1, ret, macpwr_pin; > + __maybe_unused int id_pfr1, ret; > > gd->bd->bi_boot_params = (PHYS_SDRAM_0 + 0x100); > > @@ -224,15 +224,6 @@ int board_init(void) > if (ret) > return ret; > > - /* strcmp() would look better, but doesn't get optimised away. */ > - if (CONFIG_MACPWR[0]) { > - macpwr_pin = sunxi_name_to_gpio(CONFIG_MACPWR); > - if (macpwr_pin >= 0) { > - gpio_request(macpwr_pin, "macpwr"); > - gpio_direction_output(macpwr_pin, 1); > - } > - } This version of your series does not include the CONFIG_SATAPWR removal (is that intentional or did you miss it?) so these hunks do not apply against master. I was able to cherry-pick the rc series version of the CONFIG_SATAPWR removal and everything applied fine. Just thought you should know! Cheers, Sam
Hi Sam, On 25/07/2023 22:21, Sam Edwards wrote: > Hi Andre, > > Series looks good so far! I'm trying to move my testing build over to it > now; I will report back when I've been running on it for a little bit. Cool, thanks! > > On 7/21/23 07:45, Andre Przywara wrote: >> diff --git a/board/sunxi/board.c b/board/sunxi/board.c >> index 7ac50c4ae8c..2db4a2d73ca 100644 >> --- a/board/sunxi/board.c >> +++ b/board/sunxi/board.c >> @@ -187,7 +187,7 @@ enum env_location env_get_location(enum >> env_operation op, int prio) >> /* add board specific code here */ >> int board_init(void) >> { >> - __maybe_unused int id_pfr1, ret, macpwr_pin; >> + __maybe_unused int id_pfr1, ret; >> gd->bd->bi_boot_params = (PHYS_SDRAM_0 + 0x100); >> @@ -224,15 +224,6 @@ int board_init(void) >> if (ret) >> return ret; >> - /* strcmp() would look better, but doesn't get optimised away. */ >> - if (CONFIG_MACPWR[0]) { >> - macpwr_pin = sunxi_name_to_gpio(CONFIG_MACPWR); >> - if (macpwr_pin >= 0) { >> - gpio_request(macpwr_pin, "macpwr"); >> - gpio_direction_output(macpwr_pin, 1); >> - } >> - } > > This version of your series does not include the CONFIG_SATAPWR removal > (is that intentional or did you miss it?) so these hunks do not apply > against master. I was able to cherry-pick the rc series version of the > CONFIG_SATAPWR removal and everything applied fine. Just thought you > should know! Ah, thanks for the heads up! It's actually the first patch, but I apparently had an off-by-one on the git format-patch command line. The gitlab repo has the patch: https://source.denx.de/u-boot/custodians/u-boot-sunxi/-/commits/t113s/ I will send it separately later today. Cheers, Andre
Hi Andre, Ditto my response to the previous patch. On 7/21/23 07:45, Andre Przywara wrote: > The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables > the power for the Ethernet "MAC" (mostly PHY, really). > In the DT this is described with the phy-supply property in the MAC DT > node, pointing to a (GPIO controlled) regulator. Since we need Ethernet > only in U-Boot proper, and use a DM driver there, we should use the DT > instead of hardcoding this. > > Add code to the sun8i_emac and sunxi_emac drivers to check the DT for > that regulator and enable it, at probe time. Then drop the current code > from board.c, which was doing that job before. > This allows us to remove the MACPWR Kconfig definition and the respective > values from the defconfigs. > > Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Sam Edwards <CFSworks@gmail.com> Thanks, Sam
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig index a7c5ae80a1e..dff9f5ea947 100644 --- a/arch/arm/mach-sunxi/Kconfig +++ b/arch/arm/mach-sunxi/Kconfig @@ -695,13 +695,6 @@ config OLD_SUNXI_KERNEL_COMPAT Set this to enable various workarounds for old kernels, this results in sub-optimal settings for newer kernels, only enable if needed. -config MACPWR - string "MAC power pin" - default "" - help - Set the pin used to power the MAC. This takes a string in the format - understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - config MMC1_PINS_PH bool "Pins for mmc1 are on Port H" depends on MACH_SUN4I || MACH_SUN7I || MACH_SUN8I_R40 diff --git a/board/sunxi/board.c b/board/sunxi/board.c index 7ac50c4ae8c..2db4a2d73ca 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -187,7 +187,7 @@ enum env_location env_get_location(enum env_operation op, int prio) /* add board specific code here */ int board_init(void) { - __maybe_unused int id_pfr1, ret, macpwr_pin; + __maybe_unused int id_pfr1, ret; gd->bd->bi_boot_params = (PHYS_SDRAM_0 + 0x100); @@ -224,15 +224,6 @@ int board_init(void) if (ret) return ret; - /* strcmp() would look better, but doesn't get optimised away. */ - if (CONFIG_MACPWR[0]) { - macpwr_pin = sunxi_name_to_gpio(CONFIG_MACPWR); - if (macpwr_pin >= 0) { - gpio_request(macpwr_pin, "macpwr"); - gpio_direction_output(macpwr_pin, 1); - } - } - #if CONFIG_IS_ENABLED(DM_I2C) /* * Temporary workaround for enabling I2C clocks until proper sunxi DM @@ -240,7 +231,6 @@ int board_init(void) */ i2c_init_board(); #endif - eth_init_board(); return 0; diff --git a/configs/Bananapi_M2_Ultra_defconfig b/configs/Bananapi_M2_Ultra_defconfig index a5fe76af568..2cc7bbbd8b7 100644 --- a/configs/Bananapi_M2_Ultra_defconfig +++ b/configs/Bananapi_M2_Ultra_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-r40-bananapi-m2-ultra" CONFIG_SPL=y CONFIG_MACH_SUN8I_R40=y CONFIG_DRAM_CLK=576 -CONFIG_MACPWR="PA17" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_USB1_VBUS_PIN="PH23" CONFIG_USB2_VBUS_PIN="PH23" diff --git a/configs/Bananapi_defconfig b/configs/Bananapi_defconfig index 6c2a1f630e8..f4910ba13ac 100644 --- a/configs/Bananapi_defconfig +++ b/configs/Bananapi_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi" CONFIG_SPL=y CONFIG_MACH_SUN7I=y CONFIG_DRAM_CLK=432 -CONFIG_MACPWR="PH23" CONFIG_VIDEO_COMPOSITE=y CONFIG_GMAC_TX_DELAY=3 CONFIG_AHCI=y diff --git a/configs/Bananapro_defconfig b/configs/Bananapro_defconfig index 94fd74754ea..02be8971df9 100644 --- a/configs/Bananapro_defconfig +++ b/configs/Bananapro_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapro" CONFIG_SPL=y CONFIG_MACH_SUN7I=y CONFIG_DRAM_CLK=432 -CONFIG_MACPWR="PH23" CONFIG_USB1_VBUS_PIN="PH0" CONFIG_USB2_VBUS_PIN="PH1" CONFIG_VIDEO_COMPOSITE=y diff --git a/configs/Lamobo_R1_defconfig b/configs/Lamobo_R1_defconfig index 9639cb6aad9..66f57ab3c85 100644 --- a/configs/Lamobo_R1_defconfig +++ b/configs/Lamobo_R1_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-lamobo-r1" CONFIG_SPL=y CONFIG_MACH_SUN7I=y CONFIG_DRAM_CLK=432 -CONFIG_MACPWR="PH23" CONFIG_GMAC_TX_DELAY=4 CONFIG_AHCI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set diff --git a/configs/Mele_A1000_defconfig b/configs/Mele_A1000_defconfig index f5b6d908cdc..9ac2e4839d9 100644 --- a/configs/Mele_A1000_defconfig +++ b/configs/Mele_A1000_defconfig @@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-a1000" CONFIG_SPL=y CONFIG_MACH_SUN4I=y -CONFIG_MACPWR="PH15" CONFIG_VIDEO_VGA=y CONFIG_VIDEO_COMPOSITE=y CONFIG_AHCI=y diff --git a/configs/Orangepi_defconfig b/configs/Orangepi_defconfig index c89a9a1f9dd..53edf525ec0 100644 --- a/configs/Orangepi_defconfig +++ b/configs/Orangepi_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi" CONFIG_SPL=y CONFIG_MACH_SUN7I=y CONFIG_DRAM_CLK=432 -CONFIG_MACPWR="PH23" CONFIG_USB1_VBUS_PIN="PH26" CONFIG_USB2_VBUS_PIN="PH22" CONFIG_VIDEO_VGA=y diff --git a/configs/Orangepi_mini_defconfig b/configs/Orangepi_mini_defconfig index fe9ce808a1e..ccf32670170 100644 --- a/configs/Orangepi_mini_defconfig +++ b/configs/Orangepi_mini_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-orangepi-mini" CONFIG_SPL=y CONFIG_MACH_SUN7I=y CONFIG_DRAM_CLK=432 -CONFIG_MACPWR="PH23" CONFIG_MMC_SUNXI_SLOT_EXTRA=3 CONFIG_USB1_VBUS_PIN="PH26" CONFIG_USB2_VBUS_PIN="PH22" diff --git a/configs/bananapi_m1_plus_defconfig b/configs/bananapi_m1_plus_defconfig index 0fbb619d623..a432a01f6b4 100644 --- a/configs/bananapi_m1_plus_defconfig +++ b/configs/bananapi_m1_plus_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi-m1-plus" CONFIG_SPL=y CONFIG_MACH_SUN7I=y CONFIG_DRAM_CLK=432 -CONFIG_MACPWR="PH23" CONFIG_VIDEO_COMPOSITE=y CONFIG_GMAC_TX_DELAY=3 CONFIG_AHCI=y diff --git a/configs/bananapi_m2_plus_h3_defconfig b/configs/bananapi_m2_plus_h3_defconfig index 26ced59fb02..a8f9b5044b0 100644 --- a/configs/bananapi_m2_plus_h3_defconfig +++ b/configs/bananapi_m2_plus_h3_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-bananapi-m2-plus" CONFIG_SPL=y CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=672 -CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y diff --git a/configs/bananapi_m2_plus_h5_defconfig b/configs/bananapi_m2_plus_h5_defconfig index fb6c945919a..1634f626190 100644 --- a/configs/bananapi_m2_plus_h5_defconfig +++ b/configs/bananapi_m2_plus_h5_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-bananapi-m2-plus" CONFIG_SPL=y CONFIG_MACH_SUN50I_H5=y CONFIG_DRAM_CLK=672 -CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y diff --git a/configs/i12-tvbox_defconfig b/configs/i12-tvbox_defconfig index 257dd89af45..37f0f53ae7d 100644 --- a/configs/i12-tvbox_defconfig +++ b/configs/i12-tvbox_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-i12-tvbox" CONFIG_SPL=y CONFIG_MACH_SUN7I=y CONFIG_DRAM_CLK=384 -CONFIG_MACPWR="PH21" CONFIG_VIDEO_COMPOSITE=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_I2C=y diff --git a/configs/jesurun_q5_defconfig b/configs/jesurun_q5_defconfig index 0ff666b2ee5..c99be7cea4e 100644 --- a/configs/jesurun_q5_defconfig +++ b/configs/jesurun_q5_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun4i-a10-jesurun-q5" CONFIG_SPL=y CONFIG_MACH_SUN4I=y CONFIG_DRAM_CLK=312 -CONFIG_MACPWR="PH19" CONFIG_USB0_VBUS_PIN="PB9" CONFIG_VIDEO_COMPOSITE=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set diff --git a/configs/mixtile_loftq_defconfig b/configs/mixtile_loftq_defconfig index 0e4cdc44670..2f92228eb7b 100644 --- a/configs/mixtile_loftq_defconfig +++ b/configs/mixtile_loftq_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-mixtile-loftq" CONFIG_SPL=y CONFIG_MACH_SUN6I=y CONFIG_DRAM_ZQ=251 -CONFIG_MACPWR="PA21" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_USB1_VBUS_PIN="PH24" CONFIG_USB2_VBUS_PIN="" diff --git a/configs/nanopi_m1_plus_defconfig b/configs/nanopi_m1_plus_defconfig index 76655d79ae0..078e98b644d 100644 --- a/configs/nanopi_m1_plus_defconfig +++ b/configs/nanopi_m1_plus_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-m1-plus" CONFIG_SPL=y CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=408 -CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y diff --git a/configs/nanopi_neo_plus2_defconfig b/configs/nanopi_neo_plus2_defconfig index 924ff38f17c..85ff31c6fe5 100644 --- a/configs/nanopi_neo_plus2_defconfig +++ b/configs/nanopi_neo_plus2_defconfig @@ -6,7 +6,6 @@ CONFIG_MACH_SUN50I_H5=y CONFIG_DRAM_CLK=408 CONFIG_DRAM_ZQ=3881977 # CONFIG_DRAM_ODT_EN is not set -CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y diff --git a/configs/nanopi_r1s_h5_defconfig b/configs/nanopi_r1s_h5_defconfig index 27cf172d72a..2a6f94afe40 100644 --- a/configs/nanopi_r1s_h5_defconfig +++ b/configs/nanopi_r1s_h5_defconfig @@ -6,7 +6,6 @@ CONFIG_MACH_SUN50I_H5=y CONFIG_DRAM_CLK=672 CONFIG_DRAM_ZQ=3881977 # CONFIG_DRAM_ODT_EN is not set -CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig index 777af8c60ea..fb6fbaf787a 100644 --- a/configs/orangepi_pc2_defconfig +++ b/configs/orangepi_pc2_defconfig @@ -5,7 +5,6 @@ CONFIG_SPL=y CONFIG_MACH_SUN50I_H5=y CONFIG_DRAM_CLK=672 CONFIG_DRAM_ZQ=3881977 -CONFIG_MACPWR="PD6" CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_I2C=y diff --git a/configs/orangepi_plus2e_defconfig b/configs/orangepi_plus2e_defconfig index 138a6a72b8c..5e2cbc48ea2 100644 --- a/configs/orangepi_plus2e_defconfig +++ b/configs/orangepi_plus2e_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-plus2e" CONFIG_SPL=y CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=672 -CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_I2C=y diff --git a/configs/orangepi_plus_defconfig b/configs/orangepi_plus_defconfig index ed585881d49..092ce77a6c4 100644 --- a/configs/orangepi_plus_defconfig +++ b/configs/orangepi_plus_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-plus" CONFIG_SPL=y CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=672 -CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_USB1_VBUS_PIN="PG13" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set diff --git a/configs/orangepi_win_defconfig b/configs/orangepi_win_defconfig index df11ad8c8fd..3ddaf050a48 100644 --- a/configs/orangepi_win_defconfig +++ b/configs/orangepi_win_defconfig @@ -3,7 +3,6 @@ CONFIG_ARCH_SUNXI=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-orangepi-win" CONFIG_SPL=y CONFIG_MACH_SUN50I=y -CONFIG_MACPWR="PD14" CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPI_FLASH_WINBOND=y diff --git a/configs/pine_h64_defconfig b/configs/pine_h64_defconfig index 6dac6098d04..4712b8e4694 100644 --- a/configs/pine_h64_defconfig +++ b/configs/pine_h64_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-pine-h64" CONFIG_SPL=y CONFIG_MACH_SUN50I_H6=y CONFIG_SUNXI_DRAM_H6_LPDDR3=y -CONFIG_MACPWR="PC16" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_USB3_VBUS_PIN="PL5" CONFIG_SPL_SPI_SUNXI=y diff --git a/configs/zeropi_defconfig b/configs/zeropi_defconfig index 11f3715e6dc..7901bffd159 100644 --- a/configs/zeropi_defconfig +++ b/configs/zeropi_defconfig @@ -4,7 +4,6 @@ CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-zeropi" CONFIG_SPL=y CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=408 -CONFIG_MACPWR="PD6" # CONFIG_VIDEO_DE2 is not set # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_CONSOLE_MUX=y diff --git a/drivers/net/sun8i_emac.c b/drivers/net/sun8i_emac.c index 04c3274fbe1..7b60a60ad52 100644 --- a/drivers/net/sun8i_emac.c +++ b/drivers/net/sun8i_emac.c @@ -29,6 +29,7 @@ #include <net.h> #include <reset.h> #include <wait_bit.h> +#include <power/regulator.h> #define MDIO_CMD_MII_BUSY BIT(0) #define MDIO_CMD_MII_WRITE BIT(1) @@ -167,9 +168,8 @@ struct emac_eth_dev { struct clk ephy_clk; struct reset_ctl tx_rst; struct reset_ctl ephy_rst; -#if CONFIG_IS_ENABLED(DM_GPIO) struct gpio_desc reset_gpio; -#endif + struct udevice *phy_reg; }; @@ -720,6 +720,9 @@ static int sun8i_emac_eth_probe(struct udevice *dev) sun8i_emac_set_syscon(sun8i_pdata, priv); + if (priv->phy_reg) + regulator_set_enable(priv->phy_reg, true); + sun8i_mdio_init(dev->name, dev); priv->bus = miiphy_get_dev_by_name(dev->name); @@ -829,6 +832,8 @@ static int sun8i_emac_eth_of_to_plat(struct udevice *dev) priv->sysctl_reg = (void *)syscon_base + priv->variant->syscon_offset; + device_get_supply_regulator(dev, "phy-supply", &priv->phy_reg); + pdata->phy_interface = -1; priv->phyaddr = -1; priv->use_internal_phy = false;
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables the power for the Ethernet "MAC" (mostly PHY, really). In the DT this is described with the phy-supply property in the MAC DT node, pointing to a (GPIO controlled) regulator. Since we need Ethernet only in U-Boot proper, and use a DM driver there, we should use the DT instead of hardcoding this. Add code to the sun8i_emac and sunxi_emac drivers to check the DT for that regulator and enable it, at probe time. Then drop the current code from board.c, which was doing that job before. This allows us to remove the MACPWR Kconfig definition and the respective values from the defconfigs. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm/mach-sunxi/Kconfig | 7 ------- board/sunxi/board.c | 12 +----------- configs/Bananapi_M2_Ultra_defconfig | 1 - configs/Bananapi_defconfig | 1 - configs/Bananapro_defconfig | 1 - configs/Lamobo_R1_defconfig | 1 - configs/Mele_A1000_defconfig | 1 - configs/Orangepi_defconfig | 1 - configs/Orangepi_mini_defconfig | 1 - configs/bananapi_m1_plus_defconfig | 1 - configs/bananapi_m2_plus_h3_defconfig | 1 - configs/bananapi_m2_plus_h5_defconfig | 1 - configs/i12-tvbox_defconfig | 1 - configs/jesurun_q5_defconfig | 1 - configs/mixtile_loftq_defconfig | 1 - configs/nanopi_m1_plus_defconfig | 1 - configs/nanopi_neo_plus2_defconfig | 1 - configs/nanopi_r1s_h5_defconfig | 1 - configs/orangepi_pc2_defconfig | 1 - configs/orangepi_plus2e_defconfig | 1 - configs/orangepi_plus_defconfig | 1 - configs/orangepi_win_defconfig | 1 - configs/pine_h64_defconfig | 1 - configs/zeropi_defconfig | 1 - drivers/net/sun8i_emac.c | 9 +++++++-- 25 files changed, 8 insertions(+), 42 deletions(-)