diff --git a/arch/arm/mach-k3/Kconfig b/arch/arm/mach-k3/Kconfig
index 171a7f2f25..b7ff17d43b 100644
--- a/arch/arm/mach-k3/Kconfig
+++ b/arch/arm/mach-k3/Kconfig
@@ -19,6 +19,9 @@ config SOC_K3_AM642
 config SOC_K3_AM625
 	bool "TI's K3 based AM625 SoC Family Support"
 
+config SOC_K3_J784S4
+	bool "TI's K3 based J784S4 SoC Family Support"
+
 endchoice
 
 config SYS_SOC
@@ -27,7 +30,7 @@ config SYS_SOC
 config SYS_K3_NON_SECURE_MSRAM_SIZE
 	hex
 	default 0x80000 if SOC_K3_AM654
-	default 0x100000 if SOC_K3_J721E || SOC_K3_J721S2
+	default 0x100000 if SOC_K3_J721E || SOC_K3_J721S2 || SOC_K3_J784S4
 	default 0x1c0000 if SOC_K3_AM642
 	default 0x3c000 if SOC_K3_AM625
 	help
@@ -39,7 +42,7 @@ config SYS_K3_NON_SECURE_MSRAM_SIZE
 config SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
 	hex
 	default 0x58000 if SOC_K3_AM654
-	default 0xc0000 if SOC_K3_J721E || SOC_K3_J721S2
+	default 0xc0000 if SOC_K3_J721E || SOC_K3_J721S2 || SOC_K3_J784S4
 	default 0x180000 if SOC_K3_AM642
 	default 0x38000 if SOC_K3_AM625
 	help
@@ -49,14 +52,14 @@ config SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
 config SYS_K3_MCU_SCRATCHPAD_BASE
 	hex
 	default 0x40280000 if SOC_K3_AM654
-	default 0x40280000 if SOC_K3_J721E || SOC_K3_J721S2
+	default 0x40280000 if SOC_K3_J721E || SOC_K3_J721S2 || SOC_K3_J784S4
 	help
 	  Describes the base address of MCU Scratchpad RAM.
 
 config SYS_K3_MCU_SCRATCHPAD_SIZE
 	hex
 	default 0x200 if SOC_K3_AM654
-	default 0x200 if SOC_K3_J721E || SOC_K3_J721S2
+	default 0x200 if SOC_K3_J721E || SOC_K3_J721S2 || SOC_K3_J784S4
 	help
 	  Describes the size of MCU Scratchpad RAM.
 
@@ -64,7 +67,7 @@ config SYS_K3_BOOT_PARAM_TABLE_INDEX
 	hex
 	default 0x41c7fbfc if SOC_K3_AM654
 	default 0x41cffbfc if SOC_K3_J721E
-	default 0x41cfdbfc if SOC_K3_J721S2
+	default 0x41cfdbfc if SOC_K3_J721S2 || SOC_K3_J784S4
 	default 0x701bebfc if SOC_K3_AM642
 	default 0x43c3f290 if SOC_K3_AM625
 	help
@@ -167,7 +170,7 @@ config K3_ATF_LOAD_ADDR
 
 config K3_DM_FW
 	bool "Separate DM firmware image"
-	depends on SPL && CPU_V7R && (SOC_K3_J721E || SOC_K3_J721S2 || SOC_K3_AM625) && !CLK_TI_SCI && !TI_SCI_POWER_DOMAIN
+	depends on SPL && CPU_V7R && (SOC_K3_J721E || SOC_K3_J721S2 || SOC_K3_AM625 || SOC_K3_J784S4) && !CLK_TI_SCI && !TI_SCI_POWER_DOMAIN
 	default y
 	help
 	  Enabling this will indicate that the system has separate DM
@@ -188,4 +191,5 @@ source "board/ti/am62x/Kconfig"
 source "board/ti/j721e/Kconfig"
 source "board/siemens/iot2050/Kconfig"
 source "board/ti/j721s2/Kconfig"
+source "board/ti/j784s4/Kconfig"
 endif
diff --git a/arch/arm/mach-k3/Makefile b/arch/arm/mach-k3/Makefile
index 6ac2b61c3d..f5106d8e3e 100644
--- a/arch/arm/mach-k3/Makefile
+++ b/arch/arm/mach-k3/Makefile
@@ -6,6 +6,7 @@
 obj-$(CONFIG_SOC_K3_J721E) += j721e/ j7200/
 obj-$(CONFIG_SOC_K3_J721S2) += j721s2/
 obj-$(CONFIG_SOC_K3_AM625) += am62x/
+obj-$(CONFIG_SOC_K3_J784S4) += j784s4/
 obj-$(CONFIG_ARM64) += arm64-mmu.o
 obj-$(CONFIG_CPU_V7R) += r5_mpu.o lowlevel_init.o
 obj-$(CONFIG_ARM64) += cache.o
@@ -15,6 +16,7 @@ obj-$(CONFIG_SOC_K3_J721E) += j721e_init.o
 obj-$(CONFIG_SOC_K3_J721S2) += j721s2_init.o
 obj-$(CONFIG_SOC_K3_AM642) += am642_init.o
 obj-$(CONFIG_SOC_K3_AM625) += am625_init.o
+obj-$(CONFIG_SOC_K3_J784S4) += j784s4_init.o
 obj-$(CONFIG_K3_LOAD_SYSFW) += sysfw-loader.o
 endif
 obj-y += common.o security.o
diff --git a/arch/arm/mach-k3/arm64-mmu.c b/arch/arm/mach-k3/arm64-mmu.c
index b4d7ab1f16..977d9ec9d1 100644
--- a/arch/arm/mach-k3/arm64-mmu.c
+++ b/arch/arm/mach-k3/arm64-mmu.c
@@ -262,3 +262,44 @@ struct mm_region am64_mem_map[NR_MMU_REGIONS] = {
 
 struct mm_region *mem_map = am64_mem_map;
 #endif /* CONFIG_SOC_K3_AM642 || CONFIG_SOC_K3_AM625 */
+
+#ifdef CONFIG_SOC_K3_J784S4
+#define NR_MMU_REGIONS	(CONFIG_NR_DRAM_BANKS + 3)
+
+/* ToDo: Add 64bit IO */
+struct mm_region j784s4_mem_map[NR_MMU_REGIONS] = {
+	{
+		.virt = 0x0UL,
+		.phys = 0x0UL,
+		.size = 0x80000000UL,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+			 PTE_BLOCK_NON_SHARE |
+			 PTE_BLOCK_PXN | PTE_BLOCK_UXN
+	}, {
+		.virt = 0x80000000UL,
+		.phys = 0x80000000UL,
+		.size = 0x80000000UL,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+			 PTE_BLOCK_INNER_SHARE
+	}, {
+		.virt = 0x880000000UL,
+		.phys = 0x880000000UL,
+		.size = 0x80000000UL,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+			 PTE_BLOCK_INNER_SHARE
+	}, {
+		.virt = 0x500000000UL,
+		.phys = 0x500000000UL,
+		.size = 0x400000000UL,
+		.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+			 PTE_BLOCK_NON_SHARE |
+			 PTE_BLOCK_PXN | PTE_BLOCK_UXN
+	}, {
+		/* List terminator */
+		0,
+	}
+};
+
+struct mm_region *mem_map = j784s4_mem_map;
+
+#endif /* CONFIG_SOC_K3_J784S4 */
diff --git a/arch/arm/mach-k3/include/mach/hardware.h b/arch/arm/mach-k3/include/mach/hardware.h
index d6d2cf6dc2..ce5194c180 100644
--- a/arch/arm/mach-k3/include/mach/hardware.h
+++ b/arch/arm/mach-k3/include/mach/hardware.h
@@ -26,6 +26,10 @@
 #include "am62_hardware.h"
 #endif
 
+#ifdef CONFIG_SOC_K3_J784S4
+#include "j784s4_hardware.h"
+#endif
+
 /* Assuming these addresses and definitions stay common across K3 devices */
 #define CTRLMMR_WKUP_JTAG_ID	(WKUP_CTRL_MMR0_BASE + 0x14)
 #define JTAG_ID_VARIANT_SHIFT	28
diff --git a/arch/arm/mach-k3/include/mach/j784s4_hardware.h b/arch/arm/mach-k3/include/mach/j784s4_hardware.h
new file mode 100644
index 0000000000..22313c602c
--- /dev/null
+++ b/arch/arm/mach-k3/include/mach/j784s4_hardware.h
@@ -0,0 +1,41 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * K3: J784S4 SoC definitions, structures etc.
+ *
+ * (C) Copyright (C) 2022 Texas Instruments Incorporated - http://www.ti.com/
+ */
+#ifndef __ASM_ARCH_J784S4_HARDWARE_H
+#define __ASM_ARCH_J784S4_HARDWARE_H
+
+#include <config.h>
+#ifndef __ASSEMBLY__
+#include <linux/bitops.h>
+#endif
+
+#define WKUP_CTRL_MMR0_BASE				0x43000000
+#define MCU_CTRL_MMR0_BASE				0x40f00000
+#define CTRL_MMR0_BASE					0x00100000
+
+#define CTRLMMR_MAIN_DEVSTAT				(CTRL_MMR0_BASE + 0x30)
+#define MAIN_DEVSTAT_BOOT_MODE_B_MASK			BIT(0)
+#define MAIN_DEVSTAT_BOOT_MODE_B_SHIFT			0
+#define MAIN_DEVSTAT_BKUP_BOOTMODE_MASK			GENMASK(3, 1)
+#define MAIN_DEVSTAT_BKUP_BOOTMODE_SHIFT		1
+#define MAIN_DEVSTAT_PRIM_BOOTMODE_MMC_PORT_MASK	BIT(6)
+#define MAIN_DEVSTAT_PRIM_BOOTMODE_PORT_SHIFT		6
+#define MAIN_DEVSTAT_BKUP_MMC_PORT_MASK			BIT(7)
+#define MAIN_DEVSTAT_BKUP_MMC_PORT_SHIFT		7
+
+#define CTRLMMR_WKUP_DEVSTAT				(WKUP_CTRL_MMR0_BASE + 0x30)
+#define WKUP_DEVSTAT_PRIMARY_BOOTMODE_MASK		GENMASK(5, 3)
+#define WKUP_DEVSTAT_PRIMARY_BOOTMODE_SHIFT		3
+#define WKUP_DEVSTAT_MCU_OMLY_MASK			BIT(6)
+#define WKUP_DEVSTAT_MCU_ONLY_SHIFT			6
+
+/* ROM HANDOFF Structure location */
+#define ROM_ENTENDED_BOOT_DATA_INFO			0x41cfdb00
+
+/* MCU SCRATCHPAD usage */
+#define TI_SRAM_SCRATCH_BOARD_EEPROM_START	CONFIG_SYS_K3_MCU_SCRATCHPAD_BASE
+
+#endif /* __ASM_ARCH_J784S4_HARDWARE_H */
diff --git a/arch/arm/mach-k3/include/mach/j784s4_spl.h b/arch/arm/mach-k3/include/mach/j784s4_spl.h
new file mode 100644
index 0000000000..d312a57e69
--- /dev/null
+++ b/arch/arm/mach-k3/include/mach/j784s4_spl.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2022 Texas Instruments Incorporated - http://www.ti.com/
+ *	David Huang <d-huang@ti.com>
+ */
+#ifndef _ASM_ARCH_J784S4_SPL_H_
+#define _ASM_ARCH_J784S4_SPL_H_
+
+/* With BootMode B = 0 */
+#include <linux/bitops.h>
+#define BOOT_DEVICE_HYPERFLASH		0x00
+#define BOOT_DEVICE_OSPI		0x01
+#define BOOT_DEVICE_QSPI		0x02
+#define BOOT_DEVICE_SPI			0x03
+#define BOOT_DEVICE_ETHERNET		0x04
+#define BOOT_DEVICE_I2C			0x06
+#define BOOT_DEVICE_UART		0x07
+#define BOOT_DEVICE_NOR			BOOT_DEVICE_HYPERFLASH
+
+/* With BootMode B = 1 */
+#define BOOT_DEVICE_MMC2		0x10
+#define BOOT_DEVICE_MMC1		0x11
+#define BOOT_DEVICE_DFU			0x12
+#define BOOT_DEVICE_UFS			0x13
+#define BOOT_DEVIE_GPMC			0x14
+#define BOOT_DEVICE_PCIE		0x15
+#define BOOT_DEVICE_XSPI		0x16
+#define BOOT_DEVICE_RAM			0x17
+#define BOOT_DEVICE_MMC2_2		0xFF /* Invalid value */
+
+/* Backup boot modes with MCU Only = 0 */
+#define BACKUP_BOOT_DEVICE_RAM		0x0
+#define BACKUP_BOOT_DEVICE_USB		0x1
+#define BACKUP_BOOT_DEVICE_UART		0x3
+#define BACKUP_BOOT_DEVICE_ETHERNET	0x4
+#define BACKUP_BOOT_DEVICE_MMC2		0x5
+#define BACKUP_BOOT_DEVICE_SPI		0x6
+#define BACKUP_BOOT_DEVICE_I2C		0x7
+
+#define BOOT_MODE_B_SHIFT		4
+#define BOOT_MODE_B_MASK		BIT(4)
+
+#define K3_PRIMARY_BOOTMODE		0x0
+#define K3_BACKUP_BOOTMODE		0x1
+
+#endif
diff --git a/arch/arm/mach-k3/include/mach/spl.h b/arch/arm/mach-k3/include/mach/spl.h
index c9a324a5f0..b3f8acc8bc 100644
--- a/arch/arm/mach-k3/include/mach/spl.h
+++ b/arch/arm/mach-k3/include/mach/spl.h
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
- * Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
  *	Lokesh Vutla <lokeshvutla@ti.com>
  */
 #ifndef _ASM_ARCH_SPL_H_
@@ -26,4 +26,8 @@
 #include "am62_spl.h"
 #endif
 
+#ifdef CONFIG_SOC_K3_J784S4
+#include "j784s4_spl.h"
+#endif
+
 #endif /* _ASM_ARCH_SPL_H_ */
diff --git a/arch/arm/mach-k3/j784s4/Makefile b/arch/arm/mach-k3/j784s4/Makefile
new file mode 100644
index 0000000000..d8bb3c7719
--- /dev/null
+++ b/arch/arm/mach-k3/j784s4/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier:	GPL-2.0+
+#
+# Copyright (C) 2022 Texas Instruments Incorporated - http://www.ti.com/
+obj-y += clk-data.o
+obj-y += dev-data.o
diff --git a/arch/arm/mach-k3/j784s4/clk-data.c b/arch/arm/mach-k3/j784s4/clk-data.c
new file mode 100644
index 0000000000..1c9f0698ea
--- /dev/null
+++ b/arch/arm/mach-k3/j784s4/clk-data.c
@@ -0,0 +1,428 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * J784S4 specific clock platform data
+ *
+ * This file is auto generated. Please do not hand edit and report any issues
+ * to Bryan Brattlof <bb@ti.com>.
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <linux/clk-provider.h>
+#include "k3-clk.h"
+
+static const char * const gluelogic_hfosc0_clkout_parents[] = {
+	"osc_19_2_mhz",
+	"osc_20_mhz",
+	"osc_24_mhz",
+	"osc_25_mhz",
+	"osc_26_mhz",
+	"osc_27_mhz",
+};
+
+static const char * const mcu_ospi0_iclk_sel_out0_parents[] = {
+	"board_0_mcu_ospi0_dqs_out",
+	"fss_mcu_0_ospi_0_ospi_oclk_clk",
+};
+
+static const char * const mcu_ospi1_iclk_sel_out0_parents[] = {
+	"board_0_mcu_ospi1_dqs_out",
+	"fss_mcu_0_ospi_1_ospi_oclk_clk",
+};
+
+static const char * const wkup_fref_clksel_out0_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"j7am_wakeup_16ff_wkup_0_wkup_rcosc_12p5m_clk",
+};
+
+static const char * const k3_pll_ctrl_wrap_wkup_0_sysclkout_clk_parents[] = {
+	"wkup_fref_clksel_out0",
+	"hsdiv1_16fft_mcu_0_hsdivout0_clk",
+};
+
+static const char * const mcu_ospi_ref_clk_sel_out0_parents[] = {
+	"hsdiv4_16fft_mcu_1_hsdivout4_clk",
+	"hsdiv4_16fft_mcu_2_hsdivout4_clk",
+};
+
+static const char * const mcu_ospi_ref_clk_sel_out1_parents[] = {
+	"hsdiv4_16fft_mcu_1_hsdivout4_clk",
+	"hsdiv4_16fft_mcu_2_hsdivout4_clk",
+};
+
+static const char * const wkup_gpio0_clksel_out0_parents[] = {
+	"k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk",
+	"k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk",
+	"j7am_wakeup_16ff_wkup_0_wkup_rcosc_32k_clk",
+	"j7am_wakeup_16ff_wkup_0_wkup_rcosc_12p5m_clk",
+};
+
+static const char * const mcu_usart_clksel_out0_parents[] = {
+	"hsdiv4_16fft_mcu_1_hsdivout3_clk",
+	"postdiv3_16fft_main_1_hsdivout5_clk",
+};
+
+static const char * const wkup_i2c_mcupll_bypass_out0_parents[] = {
+	"hsdiv4_16fft_mcu_1_hsdivout3_clk",
+	"gluelogic_hfosc0_clkout",
+};
+
+static const char * const main_pll_hfosc_sel_out0_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out1_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out12_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out19_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out2_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out26_0_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out27_0_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out28_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out3_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out7_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const main_pll_hfosc_sel_out8_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const usb0_refclk_sel_out0_parents[] = {
+	"gluelogic_hfosc0_clkout",
+	"board_0_hfosc1_clk_out",
+};
+
+static const char * const emmcsd1_lb_clksel_out0_parents[] = {
+	"board_0_mmc1_clklb_out",
+	"board_0_mmc1_clk_out",
+};
+
+static const char * const mcu_clkout_mux_out0_parents[] = {
+	"hsdiv4_16fft_mcu_2_hsdivout0_clk",
+	"hsdiv4_16fft_mcu_2_hsdivout0_clk",
+};
+
+static const char * const k3_pll_ctrl_wrap_main_0_sysclkout_clk_parents[] = {
+	"main_pll_hfosc_sel_out0",
+	"hsdiv4_16fft_main_0_hsdivout0_clk",
+};
+
+static const char * const dpi0_ext_clksel_out0_parents[] = {
+	"hsdiv1_16fft_main_19_hsdivout0_clk",
+	"board_0_vout0_extpclkin_out",
+};
+
+static const char * const emmcsd_refclk_sel_out0_parents[] = {
+	"hsdiv4_16fft_main_0_hsdivout2_clk",
+	"hsdiv4_16fft_main_1_hsdivout2_clk",
+	"hsdiv4_16fft_main_2_hsdivout2_clk",
+	"hsdiv4_16fft_main_3_hsdivout2_clk",
+};
+
+static const char * const emmcsd_refclk_sel_out1_parents[] = {
+	"hsdiv4_16fft_main_0_hsdivout2_clk",
+	"hsdiv4_16fft_main_1_hsdivout2_clk",
+	"hsdiv4_16fft_main_2_hsdivout2_clk",
+	"hsdiv4_16fft_main_3_hsdivout2_clk",
+};
+
+static const char * const gtc_clk_mux_out0_parents[] = {
+	"hsdiv4_16fft_main_3_hsdivout1_clk",
+	"postdiv3_16fft_main_0_hsdivout6_clk",
+	"board_0_mcu_cpts0_rft_clk_out",
+	"board_0_cpts0_rft_clk_out",
+	"board_0_mcu_ext_refclk0_out",
+	"board_0_ext_refclk1_out",
+	NULL,
+	NULL,
+	NULL,
+	NULL,
+	NULL,
+	NULL,
+	NULL,
+	NULL,
+	"hsdiv4_16fft_mcu_2_hsdivout1_clk",
+	"k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk",
+};
+
+static const struct clk_data clk_list[] = {
+	CLK_FIXED_RATE("osc_27_mhz", 27000000, 0),
+	CLK_FIXED_RATE("osc_26_mhz", 26000000, 0),
+	CLK_FIXED_RATE("osc_25_mhz", 25000000, 0),
+	CLK_FIXED_RATE("osc_24_mhz", 24000000, 0),
+	CLK_FIXED_RATE("osc_20_mhz", 20000000, 0),
+	CLK_FIXED_RATE("osc_19_2_mhz", 19200000, 0),
+	CLK_MUX("gluelogic_hfosc0_clkout", gluelogic_hfosc0_clkout_parents, 6, 0x43000030, 0, 3, 0),
+	CLK_FIXED_RATE("board_0_hfosc1_clk_out", 0, 0),
+	CLK_FIXED_RATE("board_0_mcu_ospi0_dqs_out", 0, 0),
+	CLK_FIXED_RATE("board_0_mcu_ospi1_dqs_out", 0, 0),
+	CLK_FIXED_RATE("board_0_wkup_i2c0_scl_out", 0, 0),
+	CLK_FIXED_RATE("fss_mcu_0_hyperbus1p0_0_hpb_out_clk_n", 0, 0),
+	CLK_FIXED_RATE("fss_mcu_0_hyperbus1p0_0_hpb_out_clk_p", 0, 0),
+	CLK_FIXED_RATE("fss_mcu_0_ospi_0_ospi_oclk_clk", 0, 0),
+	CLK_FIXED_RATE("fss_mcu_0_ospi_1_ospi_oclk_clk", 0, 0),
+	CLK_FIXED_RATE("j7am_wakeup_16ff_wkup_0_wkup_rcosc_12p5m_clk", 12500000, 0),
+	CLK_FIXED_RATE("j7am_wakeup_16ff_wkup_0_wkup_rcosc_32k_clk", 32000, 0),
+	CLK_MUX("mcu_ospi0_iclk_sel_out0", mcu_ospi0_iclk_sel_out0_parents, 2, 0x40f08030, 4, 1, 0),
+	CLK_MUX("mcu_ospi1_iclk_sel_out0", mcu_ospi1_iclk_sel_out0_parents, 2, 0x40f08034, 4, 1, 0),
+	CLK_FIXED_RATE("mshsi2c_wkup_0_porscl", 0, 0),
+	CLK_MUX("wkup_fref_clksel_out0", wkup_fref_clksel_out0_parents, 2, 0x43008050, 8, 1, 0),
+	CLK_PLL("pllfracf2_ssmod_16fft_mcu_0_foutvcop_clk", "wkup_fref_clksel_out0", 0x40d00000, 0),
+	CLK_PLL_DEFFREQ("pllfracf2_ssmod_16fft_mcu_1_foutvcop_clk", "wkup_fref_clksel_out0", 0x40d01000, 0, 2400000000),
+	CLK_PLL_DEFFREQ("pllfracf2_ssmod_16fft_mcu_2_foutvcop_clk", "wkup_fref_clksel_out0", 0x40d02000, 0, 2000000000),
+	CLK_DIV("hsdiv1_16fft_mcu_0_hsdivout0_clk", "pllfracf2_ssmod_16fft_mcu_0_foutvcop_clk", 0x40d00080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_mcu_1_hsdivout3_clk", "pllfracf2_ssmod_16fft_mcu_1_foutvcop_clk", 0x40d0108c, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_mcu_1_hsdivout4_clk", "pllfracf2_ssmod_16fft_mcu_1_foutvcop_clk", 0x40d01090, 0, 7, 0, 0),
+	CLK_DIV_DEFFREQ("hsdiv4_16fft_mcu_2_hsdivout4_clk", "pllfracf2_ssmod_16fft_mcu_2_foutvcop_clk", 0x40d02090, 0, 7, 0, 0, 166666666),
+	CLK_MUX_PLLCTRL("k3_pll_ctrl_wrap_wkup_0_sysclkout_clk", k3_pll_ctrl_wrap_wkup_0_sysclkout_clk_parents, 2, 0x42010000, 0),
+	CLK_DIV("k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk", "k3_pll_ctrl_wrap_wkup_0_sysclkout_clk", 0x42010118, 0, 5, 0, 0),
+	CLK_MUX("mcu_ospi_ref_clk_sel_out0", mcu_ospi_ref_clk_sel_out0_parents, 2, 0x40f08030, 0, 1, 0),
+	CLK_MUX("mcu_ospi_ref_clk_sel_out1", mcu_ospi_ref_clk_sel_out1_parents, 2, 0x40f08034, 0, 1, 0),
+	CLK_MUX("wkup_gpio0_clksel_out0", wkup_gpio0_clksel_out0_parents, 4, 0x43008070, 0, 2, 0),
+	CLK_MUX("mcu_usart_clksel_out0", mcu_usart_clksel_out0_parents, 2, 0x40f081c0, 0, 1, 0),
+	CLK_MUX("wkup_i2c_mcupll_bypass_out0", wkup_i2c_mcupll_bypass_out0_parents, 2, 0x43008060, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out0", main_pll_hfosc_sel_out0_parents, 2, 0x43008080, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out1", main_pll_hfosc_sel_out1_parents, 2, 0x43008084, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out12", main_pll_hfosc_sel_out12_parents, 2, 0x430080b0, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out19", main_pll_hfosc_sel_out19_parents, 2, 0x430080cc, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out2", main_pll_hfosc_sel_out2_parents, 2, 0x43008088, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out26_0", main_pll_hfosc_sel_out26_0_parents, 2, 0x430080e8, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out27_0", main_pll_hfosc_sel_out27_0_parents, 2, 0x430080ec, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out28", main_pll_hfosc_sel_out28_parents, 2, 0x430080f0, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out3", main_pll_hfosc_sel_out3_parents, 2, 0x4300808c, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out7", main_pll_hfosc_sel_out7_parents, 2, 0x4300809c, 0, 1, 0),
+	CLK_MUX("main_pll_hfosc_sel_out8", main_pll_hfosc_sel_out8_parents, 2, 0x430080a0, 0, 1, 0),
+	CLK_MUX("usb0_refclk_sel_out0", usb0_refclk_sel_out0_parents, 2, 0x1080e0, 0, 1, 0),
+	CLK_FIXED_RATE("board_0_cpts0_rft_clk_out", 0, 0),
+	CLK_FIXED_RATE("board_0_ext_refclk1_out", 0, 0),
+	CLK_FIXED_RATE("board_0_mcu_cpts0_rft_clk_out", 0, 0),
+	CLK_FIXED_RATE("board_0_mcu_ext_refclk0_out", 0, 0),
+	CLK_FIXED_RATE("board_0_mmc1_clklb_out", 0, 0),
+	CLK_FIXED_RATE("board_0_mmc1_clk_out", 0, 0),
+	CLK_FIXED_RATE("board_0_tck_out", 0, 0),
+	CLK_FIXED_RATE("board_0_vout0_extpclkin_out", 0, 0),
+	CLK_FIXED_RATE("emmcsd4ss_main_0_emmcsdss_io_clk_o", 0, 0),
+	CLK_DIV("hsdiv4_16fft_mcu_2_hsdivout0_clk", "pllfracf2_ssmod_16fft_mcu_2_foutvcop_clk", 0x40d02080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_mcu_2_hsdivout1_clk", "pllfracf2_ssmod_16fft_mcu_2_foutvcop_clk", 0x40d02084, 0, 7, 0, 0),
+	CLK_PLL_DEFFREQ("pllfracf2_ssmod_16fft_main_0_foutvcop_clk", "main_pll_hfosc_sel_out0", 0x680000, 0, 2000000000),
+	CLK_DIV("pllfracf2_ssmod_16fft_main_0_foutpostdiv_clk_subdiv", "pllfracf2_ssmod_16fft_main_0_foutvcop_clk", 0x680038, 16, 3, 0, CLK_DIVIDER_ONE_BASED),
+	CLK_DIV("pllfracf2_ssmod_16fft_main_0_foutpostdiv_clk", "pllfracf2_ssmod_16fft_main_0_foutpostdiv_clk_subdiv", 0x680038, 24, 3, 0, CLK_DIVIDER_ONE_BASED),
+	CLK_PLL_DEFFREQ("pllfracf2_ssmod_16fft_main_1_foutvcop_clk", "main_pll_hfosc_sel_out1", 0x681000, 0, 1920000000),
+	CLK_DIV("pllfracf2_ssmod_16fft_main_1_foutpostdiv_clk_subdiv", "pllfracf2_ssmod_16fft_main_1_foutvcop_clk", 0x681038, 16, 3, 0, CLK_DIVIDER_ONE_BASED),
+	CLK_DIV("pllfracf2_ssmod_16fft_main_1_foutpostdiv_clk", "pllfracf2_ssmod_16fft_main_1_foutpostdiv_clk_subdiv", 0x681038, 24, 3, 0, CLK_DIVIDER_ONE_BASED),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_12_foutvcop_clk", "main_pll_hfosc_sel_out12", 0x68c000, 0),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_19_foutvcop_clk", "main_pll_hfosc_sel_out19", 0x693000, 0),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_2_foutvcop_clk", "main_pll_hfosc_sel_out2", 0x682000, 0),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_26_foutvcop_clk", "main_pll_hfosc_sel_out26_0", 0x69a000, 0),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_27_foutvcop_clk", "main_pll_hfosc_sel_out27_0", 0x69b000, 0),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_28_foutvcop_clk", "main_pll_hfosc_sel_out28", 0x69c000, 0),
+	CLK_PLL_DEFFREQ("pllfracf2_ssmod_16fft_main_3_foutvcop_clk", "main_pll_hfosc_sel_out3", 0x683000, 0, 2000000000),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_7_foutvcop_clk", "main_pll_hfosc_sel_out7", 0x687000, 0),
+	CLK_PLL("pllfracf2_ssmod_16fft_main_8_foutvcop_clk", "main_pll_hfosc_sel_out8", 0x688000, 0),
+	CLK_DIV("postdiv3_16fft_main_0_hsdivout6_clk", "pllfracf2_ssmod_16fft_main_0_foutpostdiv_clk", 0x680098, 0, 7, 0, 0),
+	CLK_DIV("postdiv3_16fft_main_0_hsdivout8_clk", "pllfracf2_ssmod_16fft_main_0_foutpostdiv_clk", 0x6800a0, 0, 7, 0, 0),
+	CLK_DIV("postdiv3_16fft_main_1_hsdivout5_clk", "pllfracf2_ssmod_16fft_main_1_foutpostdiv_clk", 0x681094, 0, 7, 0, 0),
+	CLK_DIV("postdiv3_16fft_main_1_hsdivout7_clk", "pllfracf2_ssmod_16fft_main_1_foutpostdiv_clk", 0x68109c, 0, 7, 0, 0),
+	CLK_MUX("emmcsd1_lb_clksel_out0", emmcsd1_lb_clksel_out0_parents, 2, 0x1080b4, 16, 1, 0),
+	CLK_MUX("mcu_clkout_mux_out0", mcu_clkout_mux_out0_parents, 2, 0x40f08010, 0, 1, 0),
+	CLK_DIV("hsdiv0_16fft_main_12_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_12_foutvcop_clk", 0x68c080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv0_16fft_main_26_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_26_foutvcop_clk", 0x69a080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv0_16fft_main_27_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_27_foutvcop_clk", 0x69b080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv0_16fft_main_28_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_28_foutvcop_clk", 0x69c080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv0_16fft_main_7_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_7_foutvcop_clk", 0x687080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv0_16fft_main_8_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_8_foutvcop_clk", 0x688080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv1_16fft_main_19_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_19_foutvcop_clk", 0x693080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_main_0_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_0_foutvcop_clk", 0x680080, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_main_0_hsdivout2_clk", "pllfracf2_ssmod_16fft_main_0_foutvcop_clk", 0x680088, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_main_0_hsdivout3_clk", "pllfracf2_ssmod_16fft_main_0_foutvcop_clk", 0x68008c, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_main_0_hsdivout4_clk", "pllfracf2_ssmod_16fft_main_0_foutvcop_clk", 0x680090, 0, 7, 0, 0),
+	CLK_DIV_DEFFREQ("hsdiv4_16fft_main_1_hsdivout0_clk", "pllfracf2_ssmod_16fft_main_1_foutvcop_clk", 0x681080, 0, 7, 0, 0, 192000000),
+	CLK_DIV("hsdiv4_16fft_main_1_hsdivout2_clk", "pllfracf2_ssmod_16fft_main_1_foutvcop_clk", 0x681088, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_main_2_hsdivout2_clk", "pllfracf2_ssmod_16fft_main_2_foutvcop_clk", 0x682088, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_main_3_hsdivout1_clk", "pllfracf2_ssmod_16fft_main_3_foutvcop_clk", 0x683084, 0, 7, 0, 0),
+	CLK_DIV("hsdiv4_16fft_main_3_hsdivout2_clk", "pllfracf2_ssmod_16fft_main_3_foutvcop_clk", 0x683088, 0, 7, 0, 0),
+	CLK_MUX_PLLCTRL("k3_pll_ctrl_wrap_main_0_sysclkout_clk", k3_pll_ctrl_wrap_main_0_sysclkout_clk_parents, 2, 0x410000, 0),
+	CLK_DIV("k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk", "k3_pll_ctrl_wrap_main_0_sysclkout_clk", 0x410118, 0, 5, 0, 0),
+	CLK_MUX("dpi0_ext_clksel_out0", dpi0_ext_clksel_out0_parents, 2, 0x108300, 0, 1, 0),
+	CLK_MUX("emmcsd_refclk_sel_out0", emmcsd_refclk_sel_out0_parents, 4, 0x1080b0, 0, 2, 0),
+	CLK_MUX("emmcsd_refclk_sel_out1", emmcsd_refclk_sel_out1_parents, 4, 0x1080b4, 0, 2, 0),
+	CLK_MUX("gtc_clk_mux_out0", gtc_clk_mux_out0_parents, 16, 0x108030, 0, 4, 0),
+	CLK_DIV_DEFFREQ("usart_programmable_clock_divider_out0", "hsdiv4_16fft_main_1_hsdivout0_clk", 0x1081c0, 0, 2, 0, 0, 48000000),
+	CLK_DIV("usart_programmable_clock_divider_out5", "hsdiv4_16fft_main_1_hsdivout0_clk", 0x1081d4, 0, 2, 0, 0),
+	CLK_DIV("usart_programmable_clock_divider_out8", "hsdiv4_16fft_main_1_hsdivout0_clk", 0x1081e0, 0, 2, 0, 0),
+	CLK_DIV("k3_pll_ctrl_wrap_main_0_chip_div24_clk_clk", "k3_pll_ctrl_wrap_main_0_sysclkout_clk", 0x41011c, 0, 5, 0, 0),
+	CLK_DIV("k3_pll_ctrl_wrap_wkup_0_chip_div24_clk_clk", "k3_pll_ctrl_wrap_wkup_0_sysclkout_clk", 0x4201011c, 0, 5, 0, 0),
+};
+
+static const struct dev_clk soc_dev_clk_data[] = {
+	DEV_CLK(198, 0, "hsdiv0_16fft_main_8_hsdivout0_clk"),
+	DEV_CLK(198, 3, "hsdiv0_16fft_main_7_hsdivout0_clk"),
+	DEV_CLK(198, 4, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(202, 0, "hsdiv0_16fft_main_8_hsdivout0_clk"),
+	DEV_CLK(203, 0, "hsdiv0_16fft_main_8_hsdivout0_clk"),
+	DEV_CLK(61, 0, "gtc_clk_mux_out0"),
+	DEV_CLK(61, 1, "hsdiv4_16fft_main_3_hsdivout1_clk"),
+	DEV_CLK(61, 2, "postdiv3_16fft_main_0_hsdivout6_clk"),
+	DEV_CLK(61, 3, "board_0_mcu_cpts0_rft_clk_out"),
+	DEV_CLK(61, 4, "board_0_cpts0_rft_clk_out"),
+	DEV_CLK(61, 5, "board_0_mcu_ext_refclk0_out"),
+	DEV_CLK(61, 6, "board_0_ext_refclk1_out"),
+	DEV_CLK(61, 15, "hsdiv4_16fft_mcu_2_hsdivout1_clk"),
+	DEV_CLK(61, 16, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(61, 17, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(78, 0, "postdiv3_16fft_main_0_hsdivout8_clk"),
+	DEV_CLK(78, 1, "hsdiv4_16fft_main_0_hsdivout2_clk"),
+	DEV_CLK(78, 2, "hsdiv4_16fft_main_0_hsdivout3_clk"),
+	DEV_CLK(78, 3, "hsdiv4_16fft_main_0_hsdivout4_clk"),
+	DEV_CLK(78, 4, "gluelogic_hfosc0_clkout"),
+	DEV_CLK(78, 5, "board_0_hfosc1_clk_out"),
+	DEV_CLK(78, 6, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(78, 8, "gluelogic_hfosc0_clkout"),
+	DEV_CLK(78, 9, "board_0_hfosc1_clk_out"),
+	DEV_CLK(78, 10, "j7am_wakeup_16ff_wkup_0_wkup_rcosc_12p5m_clk"),
+	DEV_CLK(78, 11, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(78, 12, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(140, 1, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(140, 2, "emmcsd_refclk_sel_out0"),
+	DEV_CLK(140, 3, "hsdiv4_16fft_main_0_hsdivout2_clk"),
+	DEV_CLK(140, 4, "hsdiv4_16fft_main_1_hsdivout2_clk"),
+	DEV_CLK(140, 5, "hsdiv4_16fft_main_2_hsdivout2_clk"),
+	DEV_CLK(140, 6, "hsdiv4_16fft_main_3_hsdivout2_clk"),
+	DEV_CLK(141, 0, "emmcsd1_lb_clksel_out0"),
+	DEV_CLK(141, 3, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(141, 4, "emmcsd_refclk_sel_out1"),
+	DEV_CLK(141, 5, "hsdiv4_16fft_main_0_hsdivout2_clk"),
+	DEV_CLK(141, 6, "hsdiv4_16fft_main_1_hsdivout2_clk"),
+	DEV_CLK(141, 7, "hsdiv4_16fft_main_2_hsdivout2_clk"),
+	DEV_CLK(141, 8, "hsdiv4_16fft_main_3_hsdivout2_clk"),
+	DEV_CLK(146, 0, "usart_programmable_clock_divider_out0"),
+	DEV_CLK(146, 3, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(149, 0, "mcu_usart_clksel_out0"),
+	DEV_CLK(149, 1, "hsdiv4_16fft_mcu_1_hsdivout3_clk"),
+	DEV_CLK(149, 2, "postdiv3_16fft_main_1_hsdivout5_clk"),
+	DEV_CLK(149, 5, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(157, 174, "mcu_clkout_mux_out0"),
+	DEV_CLK(157, 175, "hsdiv4_16fft_mcu_2_hsdivout0_clk"),
+	DEV_CLK(157, 176, "hsdiv4_16fft_mcu_2_hsdivout0_clk"),
+	DEV_CLK(157, 179, "fss_mcu_0_hyperbus1p0_0_hpb_out_clk_p"),
+	DEV_CLK(157, 180, "fss_mcu_0_hyperbus1p0_0_hpb_out_clk_n"),
+	DEV_CLK(157, 224, "fss_mcu_0_ospi_0_ospi_oclk_clk"),
+	DEV_CLK(157, 226, "fss_mcu_0_ospi_0_ospi_oclk_clk"),
+	DEV_CLK(157, 228, "fss_mcu_0_ospi_1_ospi_oclk_clk"),
+	DEV_CLK(157, 230, "fss_mcu_0_ospi_1_ospi_oclk_clk"),
+	DEV_CLK(157, 239, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(157, 243, "emmcsd4ss_main_0_emmcsdss_io_clk_o"),
+	DEV_CLK(157, 245, "emmcsd4ss_main_0_emmcsdss_io_clk_o"),
+	DEV_CLK(157, 354, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(157, 359, "dpi0_ext_clksel_out0"),
+	DEV_CLK(157, 360, "mshsi2c_wkup_0_porscl"),
+	DEV_CLK(160, 0, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(160, 2, "hsdiv4_16fft_mcu_2_hsdivout4_clk"),
+	DEV_CLK(160, 4, "hsdiv4_16fft_mcu_2_hsdivout4_clk"),
+	DEV_CLK(160, 6, "hsdiv4_16fft_mcu_2_hsdivout4_clk"),
+	DEV_CLK(160, 8, "hsdiv4_16fft_mcu_2_hsdivout4_clk"),
+	DEV_CLK(161, 0, "board_0_mcu_ospi0_dqs_out"),
+	DEV_CLK(161, 1, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(161, 2, "mcu_ospi0_iclk_sel_out0"),
+	DEV_CLK(161, 3, "board_0_mcu_ospi0_dqs_out"),
+	DEV_CLK(161, 4, "fss_mcu_0_ospi_0_ospi_oclk_clk"),
+	DEV_CLK(161, 6, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(161, 7, "mcu_ospi_ref_clk_sel_out0"),
+	DEV_CLK(161, 8, "hsdiv4_16fft_mcu_1_hsdivout4_clk"),
+	DEV_CLK(161, 9, "hsdiv4_16fft_mcu_2_hsdivout4_clk"),
+	DEV_CLK(162, 0, "board_0_mcu_ospi1_dqs_out"),
+	DEV_CLK(162, 1, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(162, 2, "mcu_ospi1_iclk_sel_out0"),
+	DEV_CLK(162, 3, "board_0_mcu_ospi1_dqs_out"),
+	DEV_CLK(162, 4, "fss_mcu_0_ospi_1_ospi_oclk_clk"),
+	DEV_CLK(162, 6, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(162, 7, "mcu_ospi_ref_clk_sel_out1"),
+	DEV_CLK(162, 8, "hsdiv4_16fft_mcu_1_hsdivout4_clk"),
+	DEV_CLK(162, 9, "hsdiv4_16fft_mcu_2_hsdivout4_clk"),
+	DEV_CLK(167, 0, "wkup_gpio0_clksel_out0"),
+	DEV_CLK(178, 0, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(178, 1, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(188, 0, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(188, 1, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(191, 0, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(191, 1, "hsdiv0_16fft_main_12_hsdivout0_clk"),
+	DEV_CLK(191, 4, "hsdiv0_16fft_main_7_hsdivout0_clk"),
+	DEV_CLK(191, 5, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(192, 0, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(192, 1, "hsdiv0_16fft_main_26_hsdivout0_clk"),
+	DEV_CLK(192, 4, "hsdiv0_16fft_main_7_hsdivout0_clk"),
+	DEV_CLK(192, 5, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(193, 0, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(193, 1, "hsdiv0_16fft_main_27_hsdivout0_clk"),
+	DEV_CLK(193, 4, "hsdiv0_16fft_main_7_hsdivout0_clk"),
+	DEV_CLK(193, 5, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(194, 0, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(194, 1, "hsdiv0_16fft_main_28_hsdivout0_clk"),
+	DEV_CLK(194, 4, "hsdiv0_16fft_main_7_hsdivout0_clk"),
+	DEV_CLK(194, 5, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(201, 0, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(201, 1, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(243, 0, "j7am_wakeup_16ff_wkup_0_wkup_rcosc_12p5m_clk"),
+	DEV_CLK(243, 1, "gluelogic_hfosc0_clkout"),
+	DEV_CLK(243, 2, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(279, 0, "k3_pll_ctrl_wrap_wkup_0_chip_div1_clk_clk"),
+	DEV_CLK(279, 1, "board_0_wkup_i2c0_scl_out"),
+	DEV_CLK(279, 2, "wkup_i2c_mcupll_bypass_out0"),
+	DEV_CLK(279, 3, "hsdiv4_16fft_mcu_1_hsdivout3_clk"),
+	DEV_CLK(279, 4, "gluelogic_hfosc0_clkout"),
+	DEV_CLK(392, 0, "usart_programmable_clock_divider_out5"),
+	DEV_CLK(392, 3, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(395, 0, "usart_programmable_clock_divider_out8"),
+	DEV_CLK(395, 3, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(398, 0, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(398, 1, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(398, 2, "postdiv3_16fft_main_1_hsdivout7_clk"),
+	DEV_CLK(398, 3, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(398, 20, "k3_pll_ctrl_wrap_main_0_chip_div1_clk_clk"),
+	DEV_CLK(398, 21, "usb0_refclk_sel_out0"),
+	DEV_CLK(398, 22, "gluelogic_hfosc0_clkout"),
+	DEV_CLK(398, 23, "board_0_hfosc1_clk_out"),
+	DEV_CLK(398, 28, "board_0_tck_out"),
+};
+
+const struct ti_k3_clk_platdata j784s4_clk_platdata = {
+	.clk_list = clk_list,
+	.clk_list_cnt = 106,
+	.soc_dev_clk_data = soc_dev_clk_data,
+	.soc_dev_clk_data_cnt = 128,
+};
diff --git a/arch/arm/mach-k3/j784s4/dev-data.c b/arch/arm/mach-k3/j784s4/dev-data.c
new file mode 100644
index 0000000000..e44afad3ec
--- /dev/null
+++ b/arch/arm/mach-k3/j784s4/dev-data.c
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * J784S4 specific device platform data
+ *
+ * This file is auto generated. Please do not hand edit and report any issues
+ * to Bryan Brattlof <bb@ti.com>.
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include "k3-dev.h"
+
+static struct ti_psc soc_psc_list[] = {
+	[0] = PSC(0, 0x42000000),
+	[1] = PSC(1, 0x00420000),
+	[2] = PSC(2, 0x00400000),
+};
+
+static struct ti_pd soc_pd_list[] = {
+	[0] = PSC_PD(0, &soc_psc_list[0], NULL),
+	[1] = PSC_PD(3, &soc_psc_list[1], NULL),
+	[2] = PSC_PD(0, &soc_psc_list[2], NULL),
+	[3] = PSC_PD(1, &soc_psc_list[2], &soc_pd_list[2]),
+	[4] = PSC_PD(14, &soc_psc_list[2], NULL),
+	[5] = PSC_PD(15, &soc_psc_list[2], &soc_pd_list[4]),
+	[6] = PSC_PD(16, &soc_psc_list[2], &soc_pd_list[4]),
+	[7] = PSC_PD(38, &soc_psc_list[2], NULL),
+};
+
+static struct ti_lpsc soc_lpsc_list[] = {
+	[0] = PSC_LPSC(0, &soc_psc_list[0], &soc_pd_list[0], NULL),
+	[1] = PSC_LPSC(3, &soc_psc_list[0], &soc_pd_list[0], NULL),
+	[2] = PSC_LPSC(10, &soc_psc_list[0], &soc_pd_list[0], NULL),
+	[3] = PSC_LPSC(11, &soc_psc_list[0], &soc_pd_list[0], NULL),
+	[4] = PSC_LPSC(12, &soc_psc_list[0], &soc_pd_list[0], NULL),
+	[5] = PSC_LPSC(12, &soc_psc_list[1], &soc_pd_list[1], &soc_lpsc_list[6]),
+	[6] = PSC_LPSC(13, &soc_psc_list[1], &soc_pd_list[1], NULL),
+	[7] = PSC_LPSC(0, &soc_psc_list[2], &soc_pd_list[2], NULL),
+	[8] = PSC_LPSC(9, &soc_psc_list[2], &soc_pd_list[2], &soc_lpsc_list[2]),
+	[9] = PSC_LPSC(14, &soc_psc_list[2], &soc_pd_list[2], &soc_lpsc_list[10]),
+	[10] = PSC_LPSC(15, &soc_psc_list[2], &soc_pd_list[2], NULL),
+	[11] = PSC_LPSC(16, &soc_psc_list[2], &soc_pd_list[2], &soc_lpsc_list[12]),
+	[12] = PSC_LPSC(17, &soc_psc_list[2], &soc_pd_list[2], NULL),
+	[13] = PSC_LPSC(20, &soc_psc_list[2], &soc_pd_list[2], &soc_lpsc_list[5]),
+	[14] = PSC_LPSC(23, &soc_psc_list[2], &soc_pd_list[2], &soc_lpsc_list[5]),
+	[15] = PSC_LPSC(25, &soc_psc_list[2], &soc_pd_list[2], &soc_lpsc_list[5]),
+	[16] = PSC_LPSC(43, &soc_psc_list[2], &soc_pd_list[3], NULL),
+	[17] = PSC_LPSC(45, &soc_psc_list[2], &soc_pd_list[3], NULL),
+	[18] = PSC_LPSC(78, &soc_psc_list[2], &soc_pd_list[4], NULL),
+	[19] = PSC_LPSC(80, &soc_psc_list[2], &soc_pd_list[5], &soc_lpsc_list[18]),
+	[20] = PSC_LPSC(81, &soc_psc_list[2], &soc_pd_list[6], &soc_lpsc_list[18]),
+	[21] = PSC_LPSC(120, &soc_psc_list[2], &soc_pd_list[7], &soc_lpsc_list[22]),
+	[22] = PSC_LPSC(121, &soc_psc_list[2], &soc_pd_list[7], NULL),
+};
+
+static struct ti_dev soc_dev_list[] = {
+	PSC_DEV(160, &soc_lpsc_list[0]),
+	PSC_DEV(161, &soc_lpsc_list[0]),
+	PSC_DEV(162, &soc_lpsc_list[0]),
+	PSC_DEV(243, &soc_lpsc_list[0]),
+	PSC_DEV(149, &soc_lpsc_list[0]),
+	PSC_DEV(167, &soc_lpsc_list[1]),
+	PSC_DEV(279, &soc_lpsc_list[1]),
+	PSC_DEV(161, &soc_lpsc_list[2]),
+	PSC_DEV(162, &soc_lpsc_list[3]),
+	PSC_DEV(160, &soc_lpsc_list[4]),
+	PSC_DEV(139, &soc_lpsc_list[5]),
+	PSC_DEV(194, &soc_lpsc_list[6]),
+	PSC_DEV(78, &soc_lpsc_list[7]),
+	PSC_DEV(61, &soc_lpsc_list[8]),
+	PSC_DEV(131, &soc_lpsc_list[9]),
+	PSC_DEV(191, &soc_lpsc_list[10]),
+	PSC_DEV(132, &soc_lpsc_list[11]),
+	PSC_DEV(192, &soc_lpsc_list[12]),
+	PSC_DEV(398, &soc_lpsc_list[13]),
+	PSC_DEV(141, &soc_lpsc_list[14]),
+	PSC_DEV(140, &soc_lpsc_list[15]),
+	PSC_DEV(146, &soc_lpsc_list[16]),
+	PSC_DEV(392, &soc_lpsc_list[17]),
+	PSC_DEV(395, &soc_lpsc_list[17]),
+	PSC_DEV(198, &soc_lpsc_list[18]),
+	PSC_DEV(202, &soc_lpsc_list[19]),
+	PSC_DEV(203, &soc_lpsc_list[20]),
+	PSC_DEV(133, &soc_lpsc_list[21]),
+	PSC_DEV(193, &soc_lpsc_list[22]),
+};
+
+const struct ti_k3_pd_platdata j784s4_pd_platdata = {
+	.psc = soc_psc_list,
+	.pd = soc_pd_list,
+	.lpsc = soc_lpsc_list,
+	.devs = soc_dev_list,
+	.num_psc = 3,
+	.num_pd = 8,
+	.num_lpsc = 23,
+	.num_devs = 29,
+};
diff --git a/arch/arm/mach-k3/j784s4_init.c b/arch/arm/mach-k3/j784s4_init.c
new file mode 100644
index 0000000000..62e8169b0d
--- /dev/null
+++ b/arch/arm/mach-k3/j784s4_init.c
@@ -0,0 +1,322 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * J784S4: SoC specific initialization
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - http://www.ti.com/
+ *	Hari Nagalla <hnagalla@ti.com>
+ */
+
+#include <common.h>
+#include <init.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/armv7_mpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sysfw-loader.h>
+#include "common.h"
+#include <asm/arch/sys_proto.h>
+#include <linux/soc/ti/ti_sci_protocol.h>
+#include <dm.h>
+#include <dm/uclass-internal.h>
+#include <dm/pinctrl.h>
+#include <mmc.h>
+#include <remoteproc.h>
+
+#ifdef CONFIG_SPL_BUILD
+
+static void ctrl_mmr_unlock(void)
+{
+	/* Unlock all WKUP_CTRL_MMR0 module registers */
+	mmr_unlock(WKUP_CTRL_MMR0_BASE, 0);
+	mmr_unlock(WKUP_CTRL_MMR0_BASE, 1);
+	mmr_unlock(WKUP_CTRL_MMR0_BASE, 2);
+	mmr_unlock(WKUP_CTRL_MMR0_BASE, 3);
+	mmr_unlock(WKUP_CTRL_MMR0_BASE, 4);
+	mmr_unlock(WKUP_CTRL_MMR0_BASE, 6);
+	mmr_unlock(WKUP_CTRL_MMR0_BASE, 7);
+
+	/* Unlock all MCU_CTRL_MMR0 module registers */
+	mmr_unlock(MCU_CTRL_MMR0_BASE, 0);
+	mmr_unlock(MCU_CTRL_MMR0_BASE, 1);
+	mmr_unlock(MCU_CTRL_MMR0_BASE, 2);
+	mmr_unlock(MCU_CTRL_MMR0_BASE, 3);
+	mmr_unlock(MCU_CTRL_MMR0_BASE, 4);
+
+	/* Unlock all CTRL_MMR0 module registers */
+	mmr_unlock(CTRL_MMR0_BASE, 0);
+	mmr_unlock(CTRL_MMR0_BASE, 1);
+	mmr_unlock(CTRL_MMR0_BASE, 2);
+	mmr_unlock(CTRL_MMR0_BASE, 3);
+	mmr_unlock(CTRL_MMR0_BASE, 5);
+	mmr_unlock(CTRL_MMR0_BASE, 7);
+}
+
+void k3_mmc_stop_clock(void)
+{
+	if (IS_ENABLED(CONFIG_K3_LOAD_SYSFW)) {
+		if (spl_boot_device() == BOOT_DEVICE_MMC1) {
+			struct mmc *mmc = find_mmc_device(0);
+
+			if (!mmc)
+				return;
+
+			mmc->saved_clock = mmc->clock;
+			mmc_set_clock(mmc, 0, true);
+		}
+	}
+}
+
+void k3_mmc_restart_clock(void)
+{
+	if (IS_ENABLED(CONFIG_K3_LOAD_SYSFW)) {
+		if (spl_boot_device() == BOOT_DEVICE_MMC1) {
+			struct mmc *mmc = find_mmc_device(0);
+
+			if (!mmc)
+				return;
+
+			mmc_set_clock(mmc, mmc->saved_clock, false);
+		}
+	}
+}
+
+/*
+ * This uninitialized global variable would normal end up in the .bss section,
+ * but the .bss is cleared between writing and reading this variable, so move
+ * it to the .data section.
+ */
+u32 bootindex __attribute__((section(".data")));
+static struct rom_extended_boot_data bootdata __section(".data");
+
+static void store_boot_info_from_rom(void)
+{
+	bootindex = *(u32 *)(CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX);
+	memcpy(&bootdata, (uintptr_t *)ROM_ENTENDED_BOOT_DATA_INFO,
+	       sizeof(struct rom_extended_boot_data));
+}
+
+void board_init_f(ulong dummy)
+{
+	struct udevice *dev;
+	int ret;
+
+	/*
+	 * Cannot delay this further as there is a chance that
+	 * K3_BOOT_PARAM_TABLE_INDEX can be over written by SPL MALLOC section.
+	 */
+	store_boot_info_from_rom();
+
+	/* Make all control module registers accessible */
+	ctrl_mmr_unlock();
+
+	if (IS_ENABLED(CONFIG_CPU_V7R)) {
+		disable_linefill_optimization();
+		setup_k3_mpu_regions();
+	}
+
+	/* Init DM early */
+	spl_early_init();
+
+	/* Prepare console output */
+	preloader_console_init();
+
+	if (IS_ENABLED(CONFIG_K3_LOAD_SYSFW)) {
+		/*
+		 * Process pinctrl for the serial0 a.k.a. WKUP_UART0 module and continue
+		 * regardless of the result of pinctrl. Do this without probing the
+		 * device, but instead by searching the device that would request the
+		 * given sequence number if probed. The UART will be used by the system
+		 * firmware (SYSFW) image for various purposes and SYSFW depends on us
+		 * to initialize its pin settings.
+		 */
+		ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, &dev);
+		if (!ret)
+			pinctrl_select_state(dev, "default");
+
+		/*
+		 * Load, start up, and configure system controller firmware. Provide
+		 * the U-Boot console init function to the SYSFW post-PM configuration
+		 * callback hook, effectively switching on (or over) the console
+		 * output.
+		 */
+		k3_sysfw_loader(is_rom_loaded_sysfw(&bootdata),
+				k3_mmc_stop_clock, k3_mmc_restart_clock);
+
+		if (IS_ENABLED(CONFIG_SPL_CLK_K3)) {
+			/*
+			 * Force probe of clk_k3 driver here to ensure basic default clock
+			 * configuration is always done for enabling PM services.
+			 */
+			ret = uclass_get_device_by_driver(UCLASS_CLK,
+							  DM_DRIVER_GET(ti_clk),
+							  &dev);
+			if (ret)
+				panic("Failed to initialize clk-k3!\n");
+		}
+	}
+
+	/* Output System Firmware version info */
+	k3_sysfw_print_ver();
+
+	if (IS_ENABLED(CONFIG_TARGET_J784S4_R5_EVM)) {
+		ret = uclass_get_device_by_name(UCLASS_MISC, "msmc", &dev);
+		if (ret)
+			panic("Probe of msmc failed: %d\n", ret);
+
+		ret = uclass_get_device(UCLASS_RAM, 0, &dev);
+		if (ret)
+			panic("DRAM 0 init failed: %d\n", ret);
+
+		ret = uclass_next_device_err(&dev);
+		if (ret)
+			panic("DRAM 1 init failed: %d\n", ret);
+
+		ret = uclass_next_device_err(&dev);
+		if (ret)
+			panic("DRAM 2 init failed: %d\n", ret);
+
+		ret = uclass_next_device_err(&dev);
+		if (ret)
+			panic("DRAM 3 init failed: %d\n", ret);
+	}
+
+	spl_enable_dcache();
+}
+
+u32 spl_mmc_boot_mode(struct mmc *mmc, const u32 boot_device)
+{
+	switch (boot_device) {
+	case BOOT_DEVICE_MMC1:
+		return MMCSD_MODE_EMMCBOOT;
+	case BOOT_DEVICE_MMC2:
+		return MMCSD_MODE_FS;
+	default:
+		return MMCSD_MODE_RAW;
+	}
+}
+
+static u32 __get_backup_bootmedia(u32 main_devstat)
+{
+	u32 bkup_boot = (main_devstat & MAIN_DEVSTAT_BKUP_BOOTMODE_MASK) >>
+			MAIN_DEVSTAT_BKUP_BOOTMODE_SHIFT;
+
+	switch (bkup_boot) {
+	case BACKUP_BOOT_DEVICE_USB:
+		return BOOT_DEVICE_DFU;
+	case BACKUP_BOOT_DEVICE_UART:
+		return BOOT_DEVICE_UART;
+	case BACKUP_BOOT_DEVICE_ETHERNET:
+		return BOOT_DEVICE_ETHERNET;
+	case BACKUP_BOOT_DEVICE_MMC2:
+	{
+		u32 port = (main_devstat & MAIN_DEVSTAT_BKUP_MMC_PORT_MASK) >>
+			    MAIN_DEVSTAT_BKUP_MMC_PORT_SHIFT;
+		if (port == 0x0)
+			return BOOT_DEVICE_MMC1;
+		return BOOT_DEVICE_MMC2;
+	}
+	case BACKUP_BOOT_DEVICE_SPI:
+		return BOOT_DEVICE_SPI;
+	case BACKUP_BOOT_DEVICE_I2C:
+		return BOOT_DEVICE_I2C;
+	}
+
+	return BOOT_DEVICE_RAM;
+}
+
+static u32 __get_primary_bootmedia(u32 main_devstat, u32 wkup_devstat)
+{
+	u32 bootmode = (wkup_devstat & WKUP_DEVSTAT_PRIMARY_BOOTMODE_MASK) >>
+			WKUP_DEVSTAT_PRIMARY_BOOTMODE_SHIFT;
+
+	bootmode |= (main_devstat & MAIN_DEVSTAT_BOOT_MODE_B_MASK) <<
+			BOOT_MODE_B_SHIFT;
+
+	if (bootmode == BOOT_DEVICE_OSPI || bootmode ==	BOOT_DEVICE_QSPI ||
+	    bootmode == BOOT_DEVICE_XSPI)
+		bootmode = BOOT_DEVICE_SPI;
+
+	if (bootmode == BOOT_DEVICE_MMC2) {
+		u32 port = (main_devstat &
+			    MAIN_DEVSTAT_PRIM_BOOTMODE_MMC_PORT_MASK) >>
+			   MAIN_DEVSTAT_PRIM_BOOTMODE_PORT_SHIFT;
+		if (port == 0x0)
+			bootmode = BOOT_DEVICE_MMC1;
+	}
+
+	return bootmode;
+}
+
+u32 spl_boot_device(void)
+{
+	u32 wkup_devstat = readl(CTRLMMR_WKUP_DEVSTAT);
+	u32 main_devstat;
+
+	if (wkup_devstat & WKUP_DEVSTAT_MCU_OMLY_MASK) {
+		printf("ERROR: MCU only boot is not yet supported\n");
+		return BOOT_DEVICE_RAM;
+	}
+
+	/* MAIN CTRL MMR can only be read if MCU ONLY is 0 */
+	main_devstat = readl(CTRLMMR_MAIN_DEVSTAT);
+
+	if (bootindex == K3_PRIMARY_BOOTMODE)
+		return __get_primary_bootmedia(main_devstat, wkup_devstat);
+	else
+		return __get_backup_bootmedia(main_devstat);
+}
+#endif
+
+#define J784S4_DEV_MCU_RTI0			367
+#define J784S4_DEV_MCU_RTI1			368
+#define J784S4_DEV_MCU_ARMSS0_CPU0		346
+#define J784S4_DEV_MCU_ARMSS0_CPU1		347
+
+void release_resources_for_core_shutdown(void)
+{
+	if (IS_ENABLED(CONFIG_SYS_K3_SPL_ATF)) {
+		struct ti_sci_handle *ti_sci;
+		struct ti_sci_dev_ops *dev_ops;
+		struct ti_sci_proc_ops *proc_ops;
+		int ret;
+		u32 i;
+
+		const u32 put_device_ids[] = {
+			J784S4_DEV_MCU_RTI0,
+			J784S4_DEV_MCU_RTI1,
+		};
+
+		ti_sci = get_ti_sci_handle();
+		dev_ops = &ti_sci->ops.dev_ops;
+		proc_ops = &ti_sci->ops.proc_ops;
+
+		/* Iterate through list of devices to put (shutdown) */
+		for (i = 0; i < ARRAY_SIZE(put_device_ids); i++) {
+			u32 id = put_device_ids[i];
+
+			ret = dev_ops->put_device(ti_sci, id);
+			if (ret)
+				panic("Failed to put device %u (%d)\n", id, ret);
+		}
+
+		const u32 put_core_ids[] = {
+			J784S4_DEV_MCU_ARMSS0_CPU1,
+			J784S4_DEV_MCU_ARMSS0_CPU0,	/* Handle CPU0 after CPU1 */
+		};
+
+		/* Iterate through list of cores to put (shutdown) */
+		for (i = 0; i < ARRAY_SIZE(put_core_ids); i++) {
+			u32 id = put_core_ids[i];
+
+			/*
+			 * Queue up the core shutdown request. Note that this call
+			 * needs to be followed up by an actual invocation of an WFE
+			 * or WFI CPU instruction.
+			 */
+			ret = proc_ops->proc_shutdown_no_wait(ti_sci, id);
+			if (ret)
+				panic("Failed sending core %u shutdown message (%d)\n",
+				      id, ret);
+		}
+	}
+}
diff --git a/include/configs/j784s4_evm.h b/include/configs/j784s4_evm.h
new file mode 100644
index 0000000000..c05c16bea1
--- /dev/null
+++ b/include/configs/j784s4_evm.h
@@ -0,0 +1,146 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration header file for K3 J784S4 EVM
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Hari Nagalla <hnagalla@ti.com>
+ */
+
+#ifndef __CONFIG_J784S4_EVM_H
+#define __CONFIG_J784S4_EVM_H
+
+#include <linux/sizes.h>
+#include <config_distro_bootcmd.h>
+#include <environment/ti/mmc.h>
+#include <environment/ti/k3_rproc.h>
+#include <environment/ti/ufs.h>
+#include <environment/ti/k3_dfu.h>
+
+/* DDR Configuration */
+#define CONFIG_SYS_SDRAM_BASE1		0x880000000
+
+/* SPL Loader Configuration */
+#if defined(CONFIG_TARGET_J784S4_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
+#define CONFIG_SYS_UBOOT_BASE		0x50280000
+/* Image load address in RAM for DFU boot*/
+#else
+#define CONFIG_SYS_UBOOT_BASE		0x50080000
+#endif
+
+/* U-Boot general configuration */
+#define EXTRA_ENV_J784S4_BOARD_SETTINGS					\
+	"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"	\
+	"findfdt="							\
+		"setenv name_fdt ${default_device_tree};"		\
+		"setenv fdtfile ${name_fdt}\0"				\
+	"name_kern=Image\0"						\
+	"console=ttyS2,115200n8\0"					\
+	"args_all=setenv optargs earlycon=ns16550a,mmio32,0x02880000 "	\
+		"${mtdparts}\0"						\
+	"run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
+
+#define PARTS_DEFAULT \
+	/* Linux partitions */ \
+	"uuid_disk=${uuid_gpt_disk};" \
+	"name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"
+
+#ifdef CONFIG_SYS_K3_SPL_ATF
+#if defined(CONFIG_TARGET_J784S4_R5_EVM)
+#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
+	"addr_mcur5f0_0load=0x89000000\0"				\
+	"name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
+#elif defined(CONFIG_TARGET_J7200_R5_EVM)
+#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
+	"addr_mcur5f0_0load=0x89000000\0"				\
+	"name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0"
+#endif /* CONFIG_TARGET_J784S4_R5_EVM */
+#else
+#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
+#endif /* CONFIG_SYS_K3_SPL_ATF */
+
+/* U-Boot MMC-specific configuration */
+#define EXTRA_ENV_J784S4_BOARD_SETTINGS_MMC				\
+	"boot=mmc\0"							\
+	"mmcdev=1\0"							\
+	"bootpart=1:2\0"						\
+	"bootdir=/boot\0"						\
+	EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
+	"rd_spec=-\0"							\
+	"init_mmc=run args_all args_mmc\0"				\
+	"get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
+	"get_overlay_mmc="						\
+		"fdt address ${fdtaddr};"				\
+		"fdt resize 0x100000;"					\
+		"for overlay in $name_overlays;"			\
+		"do;"							\
+		"load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && "	\
+		"fdt apply ${dtboaddr};"				\
+		"done;\0"						\
+	"partitions=" PARTS_DEFAULT					\
+	"get_kern_mmc=load mmc ${bootpart} ${loadaddr} "		\
+		"${bootdir}/${name_kern}\0"				\
+	"get_fit_mmc=load mmc ${bootpart} ${addr_fit} "			\
+		"${bootdir}/${name_fit}\0"				\
+	"partitions=" PARTS_DEFAULT
+
+/* Set the default list of remote processors to boot */
+#if defined(CONFIG_TARGET_J784S4_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
+#ifdef DEFAULT_RPROCS
+#undef DEFAULT_RPROCS
+#endif
+#endif
+
+#ifdef CONFIG_TARGET_J784S4_A72_EVM
+#define DEFAULT_RPROCS	""						\
+		"2 /lib/firmware/j784s4-main-r5f0_0-fw "			\
+		"3 /lib/firmware/j784s4-main-r5f0_1-fw "			\
+		"4 /lib/firmware/j784s4-main-r5f1_0-fw "			\
+		"5 /lib/firmware/j784s4-main-r5f1_1-fw "			\
+		"6 /lib/firmware/j784s4-c71_0-fw "				\
+		"7 /lib/firmware/j784s4-c71_1-fw "
+#endif /* CONFIG_TARGET_J784S4_A72_EVM */
+
+#ifdef CONFIG_TARGET_J7200_A72_EVM
+#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY				\
+	"do_main_cpsw0_qsgmii_phyinit=1\0"				\
+	"init_main_cpsw0_qsgmii_phy=gpio set gpio@22_17;"		\
+		 "gpio clear gpio@22_16\0"				\
+	"main_cpsw0_qsgmii_phyinit="					\
+	"if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
+			"test ${boot} = mmc; then "			\
+		"run init_main_cpsw0_qsgmii_phy;"			\
+	"fi;\0"
+#define DEFAULT_RPROCS ""						\
+		"2 /lib/firmware/j7200-main-r5f0_0-fw "			\
+		"3 /lib/firmware/j7200-main-r5f0_1-fw "
+#endif /* CONFIG_TARGET_J7200_A72_EVM */
+
+#ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
+#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
+#endif
+
+/* set default dfu_bufsiz to 128KB (sector size of OSPI) */
+#define EXTRA_ENV_DFUARGS \
+	DFU_ALT_INFO_MMC \
+	DFU_ALT_INFO_EMMC \
+	DFU_ALT_INFO_RAM \
+	DFU_ALT_INFO_OSPI
+
+/* Incorporate settings into the U-Boot environment */
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	DEFAULT_LINUX_BOOT_ENV						\
+	DEFAULT_MMC_TI_ARGS						\
+	DEFAULT_FIT_TI_ARGS						\
+	EXTRA_ENV_J784S4_BOARD_SETTINGS					\
+	EXTRA_ENV_J784S4_BOARD_SETTINGS_MMC				\
+	EXTRA_ENV_RPROC_SETTINGS					\
+	EXTRA_ENV_DFUARGS						\
+	DEFAULT_UFS_TI_ARGS						\
+	EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
+
+/* Now for the remaining common defines */
+#include <configs/ti_armv7_common.h>
+
+/* MMC ENV related defines */
+
+#endif /* __CONFIG_J784S4_EVM_H */
