diff --git a/Makefile b/Makefile
index e3ce28791869..471ac7170aab 100644
--- a/Makefile
+++ b/Makefile
@@ -841,6 +841,7 @@ libs-y += drivers/usb/host/
 libs-y += drivers/usb/mtu3/
 libs-y += drivers/usb/musb/
 libs-y += drivers/usb/musb-new/
+libs-y += drivers/usb/isp1760/
 libs-y += drivers/usb/phy/
 libs-y += drivers/usb/ulpi/
 ifdef CONFIG_POST
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index ab1d061bd0d5..86804166de3e 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -68,6 +68,8 @@ config SPL_DM_USB_GADGET
 
 source "drivers/usb/host/Kconfig"
 
+source "drivers/usb/isp1760/Kconfig"
+
 source "drivers/usb/cdns3/Kconfig"
 
 source "drivers/usb/dwc3/Kconfig"
diff --git a/drivers/usb/common/Makefile b/drivers/usb/common/Makefile
index dc05cb0a5077..f08b064d2493 100644
--- a/drivers/usb/common/Makefile
+++ b/drivers/usb/common/Makefile
@@ -4,6 +4,7 @@
 #
 
 obj-$(CONFIG_$(SPL_)DM_USB) += common.o
+obj-$(CONFIG_USB_ISP1760) += usb_urb.o
 obj-$(CONFIG_USB_MUSB_HCD) += usb_urb.o
 obj-$(CONFIG_USB_MUSB_UDC) += usb_urb.o
 obj-$(CONFIG_USB_EHCI_FSL) += fsl-dt-fixup.o fsl-errata.o
diff --git a/drivers/usb/isp1760/Kconfig b/drivers/usb/isp1760/Kconfig
new file mode 100644
index 000000000000..993d71e74cd2
--- /dev/null
+++ b/drivers/usb/isp1760/Kconfig
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config USB_ISP1760
+	tristate "NXP ISP 1760/1761/1763 support"
+	select DM_USB
+	select USB_HOST
+	help
+	  Say Y or M here if your system as an ISP1760/1761/1763 USB host
+	  controller.
+
+	  This USB controller is usually attached to a non-DMA-Master
+	  capable bus.
diff --git a/drivers/usb/isp1760/Makefile b/drivers/usb/isp1760/Makefile
new file mode 100644
index 000000000000..2c809c01b118
--- /dev/null
+++ b/drivers/usb/isp1760/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+isp1760-y := isp1760-core.o isp1760-if.o isp1760-uboot.o isp1760-hcd.o
+
+#isp1760-hcd.o
+
+obj-$(CONFIG_USB_ISP1760) += isp1760.o
diff --git a/drivers/usb/isp1760/isp1760-core.c b/drivers/usb/isp1760/isp1760-core.c
new file mode 100644
index 000000000000..78a7e1983f6e
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-core.c
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the NXP ISP1760 chip
+ *
+ * Copyright 2022 Linaro, Rui Miguel Silva <rui.silva@linaro.org>
+ *
+ * This is based on linux kernel driver, original developed:
+ * Copyright 2014 Laurent Pinchart
+ * Copyright 2007 Sebastian Siewior
+ *
+ */
+
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <dm/device_compat.h>
+#include <dm/devres.h>
+#include <linux/compat.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <regmap.h>
+#include <usb.h>
+
+#include "isp1760-core.h"
+#include "isp1760-hcd.h"
+#include "isp1760-regs.h"
+
+#define msleep(a) udelay((a) * 1000)
+
+static int isp1760_init_core(struct isp1760_device *isp)
+{
+	struct isp1760_hcd *hcd = &isp->hcd;
+
+	/*
+	 * Reset the host controller, including the CPU interface
+	 * configuration.
+	 */
+	isp1760_field_set(hcd->fields, SW_RESET_RESET_ALL);
+	msleep(100);
+
+	/* Setup HW Mode Control: This assumes a level active-low interrupt */
+	if ((isp->devflags & ISP1760_FLAG_ANALOG_OC) && hcd->is_isp1763)
+		return -EINVAL;
+
+	if (isp->devflags & ISP1760_FLAG_BUS_WIDTH_16)
+		isp1760_field_clear(hcd->fields, HW_DATA_BUS_WIDTH);
+	if (isp->devflags & ISP1760_FLAG_BUS_WIDTH_8)
+		isp1760_field_set(hcd->fields, HW_DATA_BUS_WIDTH);
+	if (isp->devflags & ISP1760_FLAG_ANALOG_OC)
+		isp1760_field_set(hcd->fields, HW_ANA_DIGI_OC);
+	if (isp->devflags & ISP1760_FLAG_DACK_POL_HIGH)
+		isp1760_field_set(hcd->fields, HW_DACK_POL_HIGH);
+	if (isp->devflags & ISP1760_FLAG_DREQ_POL_HIGH)
+		isp1760_field_set(hcd->fields, HW_DREQ_POL_HIGH);
+	if (isp->devflags & ISP1760_FLAG_INTR_POL_HIGH)
+		isp1760_field_set(hcd->fields, HW_INTR_HIGH_ACT);
+	if (isp->devflags & ISP1760_FLAG_INTR_EDGE_TRIG)
+		isp1760_field_set(hcd->fields, HW_INTR_EDGE_TRIG);
+
+	/*
+	 * The ISP1761 has a dedicated DC IRQ line but supports sharing the HC
+	 * IRQ line for both the host and device controllers. Hardcode IRQ
+	 * sharing for now and disable the DC interrupts globally to avoid
+	 * spurious interrupts during HCD registration.
+	 */
+	if (isp->devflags & ISP1760_FLAG_ISP1761) {
+		isp1760_reg_write(hcd->regs, ISP176x_DC_MODE, 0);
+		isp1760_field_set(hcd->fields, HW_COMN_IRQ);
+	}
+
+	/*
+	 * PORT 1 Control register of the ISP1760 is the OTG control register
+	 * on ISP1761.
+	 *
+	 * TODO: Really support OTG. For now we configure port 1 in device mode
+	 */
+	if (((isp->devflags & ISP1760_FLAG_ISP1761) ||
+	     (isp->devflags & ISP1760_FLAG_ISP1763)) &&
+	    (isp->devflags & ISP1760_FLAG_PERIPHERAL_EN)) {
+		isp1760_field_set(hcd->fields, HW_DM_PULLDOWN);
+		isp1760_field_set(hcd->fields, HW_DP_PULLDOWN);
+		isp1760_field_set(hcd->fields, HW_OTG_DISABLE);
+	} else {
+		isp1760_field_set(hcd->fields, HW_SW_SEL_HC_DC);
+		isp1760_field_set(hcd->fields, HW_VBUS_DRV);
+		isp1760_field_set(hcd->fields, HW_SEL_CP_EXT);
+	}
+
+	printf("%s bus width: %u, oc: %s\n",
+	       hcd->is_isp1763 ? "isp1763" : "isp1760",
+	       isp->devflags & ISP1760_FLAG_BUS_WIDTH_8 ? 8 :
+	       isp->devflags & ISP1760_FLAG_BUS_WIDTH_16 ? 16 : 32,
+	       hcd->is_isp1763 ? "not available" :
+	       isp->devflags & ISP1760_FLAG_ANALOG_OC ? "analog" : "digital");
+
+	return 0;
+}
+
+void isp1760_set_pullup(struct isp1760_device *isp, bool enable)
+{
+	struct isp1760_hcd *hcd = &isp->hcd;
+
+	if (enable)
+		isp1760_field_set(hcd->fields, HW_DP_PULLUP);
+	else
+		isp1760_field_set(hcd->fields, HW_DP_PULLUP_CLEAR);
+}
+
+/*
+ * ISP1760/61:
+ *
+ * 60kb divided in:
+ * - 32 blocks @ 256  bytes
+ * - 20 blocks @ 1024 bytes
+ * -  4 blocks @ 8192 bytes
+ */
+static const struct isp1760_memory_layout isp176x_memory_conf = {
+	.blocks[0]		= 32,
+	.blocks_size[0]		= 256,
+	.blocks[1]		= 20,
+	.blocks_size[1]		= 1024,
+	.blocks[2]		= 4,
+	.blocks_size[2]		= 8192,
+
+	.slot_num		= 32,
+	.payload_blocks		= 32 + 20 + 4,
+	.payload_area_size	= 0xf000,
+};
+
+/*
+ * ISP1763:
+ *
+ * 20kb divided in:
+ * - 8 blocks @ 256  bytes
+ * - 2 blocks @ 1024 bytes
+ * - 4 blocks @ 4096 bytes
+ */
+static const struct isp1760_memory_layout isp1763_memory_conf = {
+	.blocks[0]		= 8,
+	.blocks_size[0]		= 256,
+	.blocks[1]		= 2,
+	.blocks_size[1]		= 1024,
+	.blocks[2]		= 4,
+	.blocks_size[2]		= 4096,
+
+	.slot_num		= 16,
+	.payload_blocks		= 8 + 2 + 4,
+	.payload_area_size	= 0x5000,
+};
+
+static const struct regmap_config isp1760_hc_regmap_conf = {
+	.width = REGMAP_SIZE_16,
+};
+
+static const struct reg_field isp1760_hc_reg_fields[] = {
+	[HCS_PPC]		= REG_FIELD(ISP176x_HC_HCSPARAMS, 4, 4),
+	[HCS_N_PORTS]		= REG_FIELD(ISP176x_HC_HCSPARAMS, 0, 3),
+	[HCC_ISOC_CACHE]	= REG_FIELD(ISP176x_HC_HCCPARAMS, 7, 7),
+	[HCC_ISOC_THRES]	= REG_FIELD(ISP176x_HC_HCCPARAMS, 4, 6),
+	[CMD_LRESET]		= REG_FIELD(ISP176x_HC_USBCMD, 7, 7),
+	[CMD_RESET]		= REG_FIELD(ISP176x_HC_USBCMD, 1, 1),
+	[CMD_RUN]		= REG_FIELD(ISP176x_HC_USBCMD, 0, 0),
+	[STS_PCD]		= REG_FIELD(ISP176x_HC_USBSTS, 2, 2),
+	[HC_FRINDEX]		= REG_FIELD(ISP176x_HC_FRINDEX, 0, 13),
+	[FLAG_CF]		= REG_FIELD(ISP176x_HC_CONFIGFLAG, 0, 0),
+	[HC_ISO_PTD_DONEMAP]	= REG_FIELD(ISP176x_HC_ISO_PTD_DONEMAP, 0, 31),
+	[HC_ISO_PTD_SKIPMAP]	= REG_FIELD(ISP176x_HC_ISO_PTD_SKIPMAP, 0, 31),
+	[HC_ISO_PTD_LASTPTD]	= REG_FIELD(ISP176x_HC_ISO_PTD_LASTPTD, 0, 31),
+	[HC_INT_PTD_DONEMAP]	= REG_FIELD(ISP176x_HC_INT_PTD_DONEMAP, 0, 31),
+	[HC_INT_PTD_SKIPMAP]	= REG_FIELD(ISP176x_HC_INT_PTD_SKIPMAP, 0, 31),
+	[HC_INT_PTD_LASTPTD]	= REG_FIELD(ISP176x_HC_INT_PTD_LASTPTD, 0, 31),
+	[HC_ATL_PTD_DONEMAP]	= REG_FIELD(ISP176x_HC_ATL_PTD_DONEMAP, 0, 31),
+	[HC_ATL_PTD_SKIPMAP]	= REG_FIELD(ISP176x_HC_ATL_PTD_SKIPMAP, 0, 31),
+	[HC_ATL_PTD_LASTPTD]	= REG_FIELD(ISP176x_HC_ATL_PTD_LASTPTD, 0, 31),
+	[PORT_OWNER]		= REG_FIELD(ISP176x_HC_PORTSC1, 13, 13),
+	[PORT_POWER]		= REG_FIELD(ISP176x_HC_PORTSC1, 12, 12),
+	[PORT_LSTATUS]		= REG_FIELD(ISP176x_HC_PORTSC1, 10, 11),
+	[PORT_RESET]		= REG_FIELD(ISP176x_HC_PORTSC1, 8, 8),
+	[PORT_SUSPEND]		= REG_FIELD(ISP176x_HC_PORTSC1, 7, 7),
+	[PORT_RESUME]		= REG_FIELD(ISP176x_HC_PORTSC1, 6, 6),
+	[PORT_PE]		= REG_FIELD(ISP176x_HC_PORTSC1, 2, 2),
+	[PORT_CSC]		= REG_FIELD(ISP176x_HC_PORTSC1, 1, 1),
+	[PORT_CONNECT]		= REG_FIELD(ISP176x_HC_PORTSC1, 0, 0),
+	[ALL_ATX_RESET]		= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 31, 31),
+	[HW_ANA_DIGI_OC]	= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 15, 15),
+	[HW_COMN_IRQ]		= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 10, 10),
+	[HW_DATA_BUS_WIDTH]	= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 8, 8),
+	[HW_DACK_POL_HIGH]	= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 6, 6),
+	[HW_DREQ_POL_HIGH]	= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 5, 5),
+	[HW_INTR_HIGH_ACT]	= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 2, 2),
+	[HW_INTR_EDGE_TRIG]	= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 1, 1),
+	[HW_GLOBAL_INTR_EN]	= REG_FIELD(ISP176x_HC_HW_MODE_CTRL, 0, 0),
+	[HC_CHIP_REV]		= REG_FIELD(ISP176x_HC_CHIP_ID, 16, 31),
+	[HC_CHIP_ID_HIGH]	= REG_FIELD(ISP176x_HC_CHIP_ID, 8, 15),
+	[HC_CHIP_ID_LOW]	= REG_FIELD(ISP176x_HC_CHIP_ID, 0, 7),
+	[HC_SCRATCH]		= REG_FIELD(ISP176x_HC_SCRATCH, 0, 31),
+	[SW_RESET_RESET_ALL]	= REG_FIELD(ISP176x_HC_RESET, 0, 0),
+	[ISO_BUF_FILL]		= REG_FIELD(ISP176x_HC_BUFFER_STATUS, 2, 2),
+	[INT_BUF_FILL]		= REG_FIELD(ISP176x_HC_BUFFER_STATUS, 1, 1),
+	[ATL_BUF_FILL]		= REG_FIELD(ISP176x_HC_BUFFER_STATUS, 0, 0),
+	[MEM_BANK_SEL]		= REG_FIELD(ISP176x_HC_MEMORY, 16, 17),
+	[MEM_START_ADDR]	= REG_FIELD(ISP176x_HC_MEMORY, 0, 15),
+	[HC_INTERRUPT]		= REG_FIELD(ISP176x_HC_INTERRUPT, 0, 9),
+	[HC_ATL_IRQ_ENABLE]	= REG_FIELD(ISP176x_HC_INTERRUPT_ENABLE, 8, 8),
+	[HC_INT_IRQ_ENABLE]	= REG_FIELD(ISP176x_HC_INTERRUPT_ENABLE, 7, 7),
+	[HC_ISO_IRQ_MASK_OR]	= REG_FIELD(ISP176x_HC_ISO_IRQ_MASK_OR, 0, 31),
+	[HC_INT_IRQ_MASK_OR]	= REG_FIELD(ISP176x_HC_INT_IRQ_MASK_OR, 0, 31),
+	[HC_ATL_IRQ_MASK_OR]	= REG_FIELD(ISP176x_HC_ATL_IRQ_MASK_OR, 0, 31),
+	[HC_ISO_IRQ_MASK_AND]	= REG_FIELD(ISP176x_HC_ISO_IRQ_MASK_AND, 0, 31),
+	[HC_INT_IRQ_MASK_AND]	= REG_FIELD(ISP176x_HC_INT_IRQ_MASK_AND, 0, 31),
+	[HC_ATL_IRQ_MASK_AND]	= REG_FIELD(ISP176x_HC_ATL_IRQ_MASK_AND, 0, 31),
+	[HW_OTG_DISABLE]	= REG_FIELD(ISP176x_HC_OTG_CTRL_SET, 10, 10),
+	[HW_SW_SEL_HC_DC]	= REG_FIELD(ISP176x_HC_OTG_CTRL_SET, 7, 7),
+	[HW_VBUS_DRV]		= REG_FIELD(ISP176x_HC_OTG_CTRL_SET, 4, 4),
+	[HW_SEL_CP_EXT]		= REG_FIELD(ISP176x_HC_OTG_CTRL_SET, 3, 3),
+	[HW_DM_PULLDOWN]	= REG_FIELD(ISP176x_HC_OTG_CTRL_SET, 2, 2),
+	[HW_DP_PULLDOWN]	= REG_FIELD(ISP176x_HC_OTG_CTRL_SET, 1, 1),
+	[HW_DP_PULLUP]		= REG_FIELD(ISP176x_HC_OTG_CTRL_SET, 0, 0),
+	[HW_OTG_DISABLE_CLEAR]	= REG_FIELD(ISP176x_HC_OTG_CTRL_CLEAR, 10, 10),
+	[HW_SW_SEL_HC_DC_CLEAR]	= REG_FIELD(ISP176x_HC_OTG_CTRL_CLEAR, 7, 7),
+	[HW_VBUS_DRV_CLEAR]	= REG_FIELD(ISP176x_HC_OTG_CTRL_CLEAR, 4, 4),
+	[HW_SEL_CP_EXT_CLEAR]	= REG_FIELD(ISP176x_HC_OTG_CTRL_CLEAR, 3, 3),
+	[HW_DM_PULLDOWN_CLEAR]	= REG_FIELD(ISP176x_HC_OTG_CTRL_CLEAR, 2, 2),
+	[HW_DP_PULLDOWN_CLEAR]	= REG_FIELD(ISP176x_HC_OTG_CTRL_CLEAR, 1, 1),
+	[HW_DP_PULLUP_CLEAR]	= REG_FIELD(ISP176x_HC_OTG_CTRL_CLEAR, 0, 0),
+};
+
+static const struct regmap_config isp1763_hc_regmap_conf = {
+	.width = REGMAP_SIZE_16,
+};
+
+static const struct reg_field isp1763_hc_reg_fields[] = {
+	[CMD_LRESET]		= REG_FIELD(ISP1763_HC_USBCMD, 7, 7),
+	[CMD_RESET]		= REG_FIELD(ISP1763_HC_USBCMD, 1, 1),
+	[CMD_RUN]		= REG_FIELD(ISP1763_HC_USBCMD, 0, 0),
+	[STS_PCD]		= REG_FIELD(ISP1763_HC_USBSTS, 2, 2),
+	[HC_FRINDEX]		= REG_FIELD(ISP1763_HC_FRINDEX, 0, 13),
+	[FLAG_CF]		= REG_FIELD(ISP1763_HC_CONFIGFLAG, 0, 0),
+	[HC_ISO_PTD_DONEMAP]	= REG_FIELD(ISP1763_HC_ISO_PTD_DONEMAP, 0, 15),
+	[HC_ISO_PTD_SKIPMAP]	= REG_FIELD(ISP1763_HC_ISO_PTD_SKIPMAP, 0, 15),
+	[HC_ISO_PTD_LASTPTD]	= REG_FIELD(ISP1763_HC_ISO_PTD_LASTPTD, 0, 15),
+	[HC_INT_PTD_DONEMAP]	= REG_FIELD(ISP1763_HC_INT_PTD_DONEMAP, 0, 15),
+	[HC_INT_PTD_SKIPMAP]	= REG_FIELD(ISP1763_HC_INT_PTD_SKIPMAP, 0, 15),
+	[HC_INT_PTD_LASTPTD]	= REG_FIELD(ISP1763_HC_INT_PTD_LASTPTD, 0, 15),
+	[HC_ATL_PTD_DONEMAP]	= REG_FIELD(ISP1763_HC_ATL_PTD_DONEMAP, 0, 15),
+	[HC_ATL_PTD_SKIPMAP]	= REG_FIELD(ISP1763_HC_ATL_PTD_SKIPMAP, 0, 15),
+	[HC_ATL_PTD_LASTPTD]	= REG_FIELD(ISP1763_HC_ATL_PTD_LASTPTD, 0, 15),
+	[PORT_OWNER]		= REG_FIELD(ISP1763_HC_PORTSC1, 13, 13),
+	[PORT_POWER]		= REG_FIELD(ISP1763_HC_PORTSC1, 12, 12),
+	[PORT_LSTATUS]		= REG_FIELD(ISP1763_HC_PORTSC1, 10, 11),
+	[PORT_RESET]		= REG_FIELD(ISP1763_HC_PORTSC1, 8, 8),
+	[PORT_SUSPEND]		= REG_FIELD(ISP1763_HC_PORTSC1, 7, 7),
+	[PORT_RESUME]		= REG_FIELD(ISP1763_HC_PORTSC1, 6, 6),
+	[PORT_PE]		= REG_FIELD(ISP1763_HC_PORTSC1, 2, 2),
+	[PORT_CSC]		= REG_FIELD(ISP1763_HC_PORTSC1, 1, 1),
+	[PORT_CONNECT]		= REG_FIELD(ISP1763_HC_PORTSC1, 0, 0),
+	[HW_DATA_BUS_WIDTH]	= REG_FIELD(ISP1763_HC_HW_MODE_CTRL, 4, 4),
+	[HW_DACK_POL_HIGH]	= REG_FIELD(ISP1763_HC_HW_MODE_CTRL, 6, 6),
+	[HW_DREQ_POL_HIGH]	= REG_FIELD(ISP1763_HC_HW_MODE_CTRL, 5, 5),
+	[HW_INTF_LOCK]		= REG_FIELD(ISP1763_HC_HW_MODE_CTRL, 3, 3),
+	[HW_INTR_HIGH_ACT]	= REG_FIELD(ISP1763_HC_HW_MODE_CTRL, 2, 2),
+	[HW_INTR_EDGE_TRIG]	= REG_FIELD(ISP1763_HC_HW_MODE_CTRL, 1, 1),
+	[HW_GLOBAL_INTR_EN]	= REG_FIELD(ISP1763_HC_HW_MODE_CTRL, 0, 0),
+	[SW_RESET_RESET_ATX]	= REG_FIELD(ISP1763_HC_RESET, 3, 3),
+	[SW_RESET_RESET_ALL]	= REG_FIELD(ISP1763_HC_RESET, 0, 0),
+	[HC_CHIP_ID_HIGH]	= REG_FIELD(ISP1763_HC_CHIP_ID, 0, 15),
+	[HC_CHIP_ID_LOW]	= REG_FIELD(ISP1763_HC_CHIP_REV, 8, 15),
+	[HC_CHIP_REV]		= REG_FIELD(ISP1763_HC_CHIP_REV, 0, 7),
+	[HC_SCRATCH]		= REG_FIELD(ISP1763_HC_SCRATCH, 0, 15),
+	[ISO_BUF_FILL]		= REG_FIELD(ISP1763_HC_BUFFER_STATUS, 2, 2),
+	[INT_BUF_FILL]		= REG_FIELD(ISP1763_HC_BUFFER_STATUS, 1, 1),
+	[ATL_BUF_FILL]		= REG_FIELD(ISP1763_HC_BUFFER_STATUS, 0, 0),
+	[MEM_START_ADDR]	= REG_FIELD(ISP1763_HC_MEMORY, 0, 15),
+	[HC_DATA]		= REG_FIELD(ISP1763_HC_DATA, 0, 15),
+	[HC_INTERRUPT]		= REG_FIELD(ISP1763_HC_INTERRUPT, 0, 10),
+	[HC_ATL_IRQ_ENABLE]	= REG_FIELD(ISP1763_HC_INTERRUPT_ENABLE, 8, 8),
+	[HC_INT_IRQ_ENABLE]	= REG_FIELD(ISP1763_HC_INTERRUPT_ENABLE, 7, 7),
+	[HC_ISO_IRQ_MASK_OR]	= REG_FIELD(ISP1763_HC_ISO_IRQ_MASK_OR, 0, 15),
+	[HC_INT_IRQ_MASK_OR]	= REG_FIELD(ISP1763_HC_INT_IRQ_MASK_OR, 0, 15),
+	[HC_ATL_IRQ_MASK_OR]	= REG_FIELD(ISP1763_HC_ATL_IRQ_MASK_OR, 0, 15),
+	[HC_ISO_IRQ_MASK_AND]	= REG_FIELD(ISP1763_HC_ISO_IRQ_MASK_AND, 0, 15),
+	[HC_INT_IRQ_MASK_AND]	= REG_FIELD(ISP1763_HC_INT_IRQ_MASK_AND, 0, 15),
+	[HC_ATL_IRQ_MASK_AND]	= REG_FIELD(ISP1763_HC_ATL_IRQ_MASK_AND, 0, 15),
+	[HW_HC_2_DIS]		= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 15, 15),
+	[HW_OTG_DISABLE]	= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 10, 10),
+	[HW_SW_SEL_HC_DC]	= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 7, 7),
+	[HW_VBUS_DRV]		= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 4, 4),
+	[HW_SEL_CP_EXT]		= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 3, 3),
+	[HW_DM_PULLDOWN]	= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 2, 2),
+	[HW_DP_PULLDOWN]	= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 1, 1),
+	[HW_DP_PULLUP]		= REG_FIELD(ISP1763_HC_OTG_CTRL_SET, 0, 0),
+	[HW_HC_2_DIS_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 15, 15),
+	[HW_OTG_DISABLE_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 10, 10),
+	[HW_SW_SEL_HC_DC_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 7, 7),
+	[HW_VBUS_DRV_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 4, 4),
+	[HW_SEL_CP_EXT_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 3, 3),
+	[HW_DM_PULLDOWN_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 2, 2),
+	[HW_DP_PULLDOWN_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 1, 1),
+	[HW_DP_PULLUP_CLEAR]	= REG_FIELD(ISP1763_HC_OTG_CTRL_CLEAR, 0, 0),
+};
+
+int isp1760_register(struct isp1760_device *isp, struct resource *mem, int irq,
+		     unsigned long irqflags)
+{
+	const struct regmap_config *hc_regmap;
+	const struct reg_field *hc_reg_fields;
+	struct isp1760_hcd *hcd;
+	struct regmap_field *f;
+	unsigned int devflags;
+	struct udevice *dev;
+	int ret;
+	int i;
+
+	hcd = &isp->hcd;
+	devflags = isp->devflags;
+	dev = isp->dev;
+
+	hcd->is_isp1763 = !!(devflags & ISP1760_FLAG_ISP1763);
+
+	if (!hcd->is_isp1763 && (devflags & ISP1760_FLAG_BUS_WIDTH_8)) {
+		dev_err(dev, "isp1760/61 do not support data width 8\n");
+		return -EINVAL;
+	}
+
+	if (hcd->is_isp1763) {
+		hc_regmap = &isp1763_hc_regmap_conf;
+		hc_reg_fields = &isp1763_hc_reg_fields[0];
+	} else {
+		hc_regmap = &isp1760_hc_regmap_conf;
+		hc_reg_fields = &isp1760_hc_reg_fields[0];
+	}
+
+	hcd->base = devm_ioremap(dev, mem->start, resource_size(mem));
+	if (IS_ERR(hcd->base))
+		return PTR_ERR(hcd->base);
+
+	hcd->regs = devm_regmap_init(dev, NULL, NULL, hc_regmap);
+	if (IS_ERR(hcd->regs))
+		return PTR_ERR(hcd->regs);
+
+	for (i = 0; i < HC_FIELD_MAX; i++) {
+		f = devm_regmap_field_alloc(dev, hcd->regs, hc_reg_fields[i]);
+		if (IS_ERR(f))
+			return PTR_ERR(f);
+
+		hcd->fields[i] = f;
+	}
+
+	if (hcd->is_isp1763)
+		hcd->memory_layout = &isp1763_memory_conf;
+	else
+		hcd->memory_layout = &isp176x_memory_conf;
+
+	ret = isp1760_init_core(isp);
+	if (ret < 0)
+		return ret;
+
+	hcd->dev = dev;
+
+	ret = isp1760_hcd_register(hcd, mem, irq, irqflags, dev);
+	if (ret < 0)
+		return ret;
+
+	ret = isp1760_hcd_lowlevel_init(hcd);
+	if (ret < 0)
+		return ret;
+
+	dev_set_drvdata(dev, isp);
+
+	return 0;
+}
+
+void isp1760_unregister(struct isp1760_device *isp)
+{
+	isp1760_hcd_unregister(&isp->hcd);
+}
diff --git a/drivers/usb/isp1760/isp1760-core.h b/drivers/usb/isp1760/isp1760-core.h
new file mode 100644
index 000000000000..0a60e30b5fe7
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-core.h
@@ -0,0 +1,96 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Driver for the NXP ISP1760 chip
+ *
+ * Copyright 2021 Linaro, Rui Miguel Silva
+ * Copyright 2014 Laurent Pinchart
+ * Copyright 2007 Sebastian Siewior
+ *
+ * Contacts:
+ *	Sebastian Siewior <bigeasy@linutronix.de>
+ *	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *	Rui Miguel Silva <rui.silva@linaro.org>
+ */
+
+#ifndef _ISP1760_CORE_H_
+#define _ISP1760_CORE_H_
+
+#include <linux/compat.h>
+#include <linux/ioport.h>
+#include <regmap.h>
+
+#include "isp1760-hcd.h"
+
+struct device;
+struct gpio_desc;
+
+/*
+ * Device flags that can vary from board to board.  All of these
+ * indicate the most "atypical" case, so that a devflags of 0 is
+ * a sane default configuration.
+ */
+#define ISP1760_FLAG_BUS_WIDTH_16	0x00000002 /* 16-bit data bus width */
+#define ISP1760_FLAG_PERIPHERAL_EN	0x00000004 /* Port 1 supports Peripheral mode*/
+#define ISP1760_FLAG_ANALOG_OC		0x00000008 /* Analog overcurrent */
+#define ISP1760_FLAG_DACK_POL_HIGH	0x00000010 /* DACK active high */
+#define ISP1760_FLAG_DREQ_POL_HIGH	0x00000020 /* DREQ active high */
+#define ISP1760_FLAG_ISP1761		0x00000040 /* Chip is ISP1761 */
+#define ISP1760_FLAG_INTR_POL_HIGH	0x00000080 /* Interrupt polarity active high */
+#define ISP1760_FLAG_INTR_EDGE_TRIG	0x00000100 /* Interrupt edge triggered */
+#define ISP1760_FLAG_ISP1763		0x00000200 /* Chip is ISP1763 */
+#define ISP1760_FLAG_BUS_WIDTH_8	0x00000400 /* 8-bit data bus width */
+
+struct isp1760_device {
+	struct udevice *dev;
+
+	unsigned int devflags;
+	struct gpio_desc *rst_gpio;
+
+	struct isp1760_hcd hcd;
+};
+
+int isp1760_register(struct isp1760_device *isp, struct resource *mem, int irq,
+		     unsigned long irqflags);
+void isp1760_unregister(struct isp1760_device *isp);
+
+void isp1760_set_pullup(struct isp1760_device *isp, bool enable);
+
+static inline u32 isp1760_field_read(struct regmap_field **fields, u32 field)
+{
+	unsigned int val;
+
+	regmap_field_read(fields[field], &val);
+
+	return val;
+}
+
+static inline void isp1760_field_write(struct regmap_field **fields, u32 field,
+				       u32 val)
+{
+	regmap_field_write(fields[field], val);
+}
+
+static inline void isp1760_field_set(struct regmap_field **fields, u32 field)
+{
+	isp1760_field_write(fields, field, 0xFFFFFFFF);
+}
+
+static inline void isp1760_field_clear(struct regmap_field **fields, u32 field)
+{
+	isp1760_field_write(fields, field, 0);
+}
+
+static inline u32 isp1760_reg_read(struct regmap *regs, u32 reg)
+{
+	unsigned int val;
+
+	regmap_read(regs, reg, &val);
+
+	return val;
+}
+
+static inline void isp1760_reg_write(struct regmap *regs, u32 reg, u32 val)
+{
+	regmap_write(regs, reg, val);
+}
+#endif
diff --git a/drivers/usb/isp1760/isp1760-hcd.c b/drivers/usb/isp1760/isp1760-hcd.c
new file mode 100644
index 000000000000..a6c4d97aee3f
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-hcd.c
@@ -0,0 +1,2477 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the NXP ISP1760 chip
+ *
+ * Copyright 2021 Linaro, Rui Miguel Silva <rui.silva@linaro.org>
+ *
+ */
+
+#include <hexdump.h>
+#include <common.h>
+#include <asm/cache.h>
+#include <cpu_func.h>
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <dm/device_compat.h>
+#include <linux/bug.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/usb/usb_urb_compat.h>
+#include <usb.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <asm/unaligned.h>
+
+#include "isp1760-core.h"
+#include "isp1760-hcd.h"
+#include "isp1760-regs.h"
+#include "isp1760-uboot.h"
+
+#define ISP1760_LANGUAGE_DESC		"\4\3\19\4"
+#define ISP1760_VENDOR_DESC		"\16\3U\0-\0B\0o\0o\0t\0"
+#define ISP1760_PRODUCT_NAME_DESC	"\52\3I\0S\0P\0-\0 \0H\0o\0s\0t\0 \0C\0o\0n\0t\0r\0o\0l\0l\0e\0r\0"
+
+static struct kmem_cache *qtd_cachep;
+static struct kmem_cache *qh_cachep;
+static struct kmem_cache *urb_listitem_cachep;
+
+typedef void (packet_enqueue)(struct usb_hcd *hcd, struct isp1760_qh *qh,
+			      struct isp1760_qtd *qtd);
+
+static inline struct isp1760_hcd *hcd_to_priv(struct usb_hcd *hcd)
+{
+	return hcd->hcd_priv;
+}
+
+#define dw_to_le32(x)	(cpu_to_le32((__force u32)x))
+#define le32_to_dw(x)	((__force __dw)(le32_to_cpu(x)))
+
+/* urb state*/
+#define DELETE_URB		(0x0008)
+#define NO_TRANSFER_ACTIVE	(0xffffffff)
+
+/* Philips Proprietary Transfer Descriptor (PTD) */
+typedef __u32 __bitwise __dw;
+struct ptd {
+	__dw dw0;
+	__dw dw1;
+	__dw dw2;
+	__dw dw3;
+	__dw dw4;
+	__dw dw5;
+	__dw dw6;
+	__dw dw7;
+};
+
+struct ptd_le32 {
+	__le32 dw0;
+	__le32 dw1;
+	__le32 dw2;
+	__le32 dw3;
+	__le32 dw4;
+	__le32 dw5;
+	__le32 dw6;
+	__le32 dw7;
+};
+
+#define PTD_OFFSET		0x0400
+#define ISO_PTD_OFFSET		0x0400
+#define INT_PTD_OFFSET		0x0800
+#define ATL_PTD_OFFSET		0x0c00
+#define PAYLOAD_OFFSET		0x1000
+
+#define ISP_BANK_0		0x00
+#define ISP_BANK_1		0x01
+#define ISP_BANK_2		0x02
+#define ISP_BANK_3		0x03
+
+#define TO_DW(x)	((__force __dw)x)
+#define TO_U32(x)	((__force u32)x)
+
+ /* ATL */
+ /* DW0 */
+#define DW0_VALID_BIT			TO_DW(1)
+#define FROM_DW0_VALID(x)		(TO_U32(x) & 0x01)
+#define TO_DW0_LENGTH(x)		TO_DW((((u32)x) << 3))
+#define TO_DW0_MAXPACKET(x)		TO_DW((((u32)x) << 18))
+#define TO_DW0_MULTI(x)			TO_DW((((u32)x) << 29))
+#define TO_DW0_ENDPOINT(x)		TO_DW((((u32)x) << 31))
+/* DW1 */
+#define TO_DW1_DEVICE_ADDR(x)		TO_DW((((u32)x) << 3))
+#define TO_DW1_PID_TOKEN(x)		TO_DW((((u32)x) << 10))
+#define DW1_TRANS_BULK			TO_DW(((u32)2 << 12))
+#define DW1_TRANS_INT			TO_DW(((u32)3 << 12))
+#define DW1_TRANS_SPLIT			TO_DW(((u32)1 << 14))
+#define DW1_SE_USB_LOSPEED		TO_DW(((u32)2 << 16))
+#define TO_DW1_PORT_NUM(x)		TO_DW((((u32)x) << 18))
+#define TO_DW1_HUB_NUM(x)		TO_DW((((u32)x) << 25))
+/* DW2 */
+#define TO_DW2_DATA_START_ADDR(x)	TO_DW((((u32)x) << 8))
+#define TO_DW2_RL(x)			TO_DW(((x) << 25))
+#define FROM_DW2_RL(x)			((TO_U32(x) >> 25) & 0xf)
+/* DW3 */
+#define FROM_DW3_NRBYTESTRANSFERRED(x)		TO_U32((x) & 0x3fff)
+#define FROM_DW3_SCS_NRBYTESTRANSFERRED(x)	TO_U32((x) & 0x07ff)
+#define TO_DW3_NAKCOUNT(x)		TO_DW(((x) << 19))
+#define FROM_DW3_NAKCOUNT(x)		((TO_U32(x) >> 19) & 0xf)
+#define TO_DW3_CERR(x)			TO_DW(((x) << 23))
+#define FROM_DW3_CERR(x)		((TO_U32(x) >> 23) & 0x3)
+#define TO_DW3_DATA_TOGGLE(x)		TO_DW(((x) << 25))
+#define FROM_DW3_DATA_TOGGLE(x)		((TO_U32(x) >> 25) & 0x1)
+#define TO_DW3_PING(x)			TO_DW(((x) << 26))
+#define FROM_DW3_PING(x)		((TO_U32(x) >> 26) & 0x1)
+#define DW3_ERROR_BIT			TO_DW((1 << 28))
+#define DW3_BABBLE_BIT			TO_DW((1 << 29))
+#define DW3_HALT_BIT			TO_DW((1 << 30))
+#define DW3_ACTIVE_BIT			TO_DW((1 << 31))
+#define FROM_DW3_ACTIVE(x)		((TO_U32(x) >> 31) & 0x01)
+
+#define INT_UNDERRUN			BIT(2)
+#define INT_BABBLE			BIT(1)
+#define INT_EXACT			BIT(0)
+
+#define SETUP_PID	(2)
+#define IN_PID		(1)
+#define OUT_PID		(0)
+
+/* Errata 1 */
+#define RL_COUNTER	(0)
+#define NAK_COUNTER	(0)
+#define ERR_COUNTER	(3)
+
+struct isp1760_qtd {
+	u8 packet_type;
+	void *data_buffer;
+	u32 payload_addr;
+
+	/* the rest is HCD-private */
+	struct list_head qtd_list;
+	struct urb *urb;
+	size_t length;
+	size_t actual_length;
+
+	/*
+	 * QTD_ENQUEUED:	waiting for transfer (inactive)
+	 * QTD_PAYLOAD_ALLOC:	chip mem has been allocated for payload
+	 * QTD_XFER_STARTED:	valid ptd has been written to isp176x - only
+	 *			interrupt handler may touch this qtd!
+	 * QTD_XFER_COMPLETE:	payload has been transferred successfully
+	 * QTD_RETIRE:		transfer error/abort qtd
+	 */
+#define QTD_ENQUEUED		0
+#define QTD_PAYLOAD_ALLOC	1
+#define QTD_XFER_STARTED	2
+#define QTD_XFER_COMPLETE	3
+#define QTD_RETIRE		4
+	u32 status;
+};
+
+/* Queue head, one for each active endpoint */
+struct isp1760_qh {
+	struct list_head qh_list;
+	struct list_head qtd_list;
+	int epnum;
+	u32 toggle;
+	u32 ping;
+	int slot;
+	int tt_buffer_dirty;	/* See USB2.0 spec section 11.17.5 */
+};
+
+struct urb_listitem {
+	struct list_head urb_list;
+	struct urb *urb;
+};
+
+static const u32 isp1763_hc_portsc1_fields[] = {
+	[PORT_OWNER]		= BIT(13),
+	[PORT_POWER]		= BIT(12),
+	[PORT_LSTATUS]		= BIT(10),
+	[PORT_RESET]		= BIT(8),
+	[PORT_SUSPEND]		= BIT(7),
+	[PORT_RESUME]		= BIT(6),
+	[PORT_PE]		= BIT(2),
+	[PORT_CSC]		= BIT(1),
+	[PORT_CONNECT]		= BIT(0),
+};
+
+static struct descriptor {
+	struct usb_device_descriptor device;
+	struct usb_config_descriptor config;
+	struct usb_interface_descriptor interface;
+	struct usb_endpoint_descriptor endpoint;
+} __packed rh_descriptor = {
+	{
+		/* usb 2.0 root hub device descriptor */
+		0x12,       /*  __u8  bLength; */
+		USB_DT_DEVICE, /* __u8 bDescriptorType; Device */
+		0x0002, /*  __le16 bcdUSB; v2.0 */
+
+		0x09,       /*  __u8  bDeviceClass; HUB_CLASSCODE */
+		0x00,       /*  __u8  bDeviceSubClass; */
+		0x00,       /*  __u8  bDeviceProtocol; [ usb 2.0 no TT ] */
+		0x40,       /*  __u8  bMaxPacketSize0; 64 Bytes */
+
+		0x6b1d,     /*  __le16 idVendor; Linux Foundation 0x1d6b */
+		0x0200,     /*  __le16 idProduct; device 0x0002 */
+		0x0001,     /*  __le16 bcdDevice */
+
+		0x03,       /*  __u8  iManufacturer; */
+		0x02,       /*  __u8  iProduct; */
+		0x01,       /*  __u8  iSerialNumber; */
+		0x01        /*  __u8  bNumConfigurations; */
+	}, {
+		/* one configuration */
+		0x09,       /*  __u8  bLength; */
+		USB_DT_CONFIG, /* __u8 bDescriptorType; Configuration */
+		0x1900,     /*  __le16 wTotalLength; */
+		0x01,       /*  __u8  bNumInterfaces; (1) */
+		0x01,       /*  __u8  bConfigurationValue; */
+		0x00,       /*  __u8  iConfiguration; */
+		0xc0,       /*  __u8  bmAttributes;
+			     *		Bit 7: must be set,
+			     *		6: Self-powered,
+			     *		5: Remote wakeup,
+			     *		4..0: resvd
+			     */
+		0x00,       /*  __u8  MaxPower; */
+	}, {
+		/* one interface */
+		0x09,       /*  __u8  if_bLength; */
+		USB_DT_INTERFACE, /* __u8 if_bDescriptorType; Interface */
+		0x00,       /*  __u8  if_bInterfaceNumber; */
+		0x00,       /*  __u8  if_bAlternateSetting; */
+		0x01,       /*  __u8  if_bNumEndpoints; */
+		0x09,       /*  __u8  if_bInterfaceClass; HUB_CLASSCODE */
+		0x00,       /*  __u8  if_bInterfaceSubClass; */
+		0x00,       /*  __u8  if_bInterfaceProtocol; [usb1.1 or single tt] */
+		0x00,       /*  __u8  if_iInterface; */
+	}, {
+		/* one endpoint (status change endpoint) */
+		0x07,       /*  __u8  ep_bLength; */
+		USB_DT_ENDPOINT, /* __u8 ep_bDescriptorType; Endpoint */
+		0x81,       /*  __u8  ep_bEndpointAddress; IN Endpoint 1 */
+		0x03,       /*  __u8  ep_bmAttributes; Interrupt */
+			/* __le16 ep_wMaxPacketSize; 1 + (MAX_ROOT_PORTS / 8) */
+			/* see hub.c:hub_configure() for details. */
+		(USB_MAXCHILDREN + 1 + 7) / 8, 0x00,
+		0x0c        /*  __u8  ep_bInterval; (256ms -- usb 2.0 spec) */
+	},
+};
+
+/*
+ * Access functions for isp176x registers regmap fields
+ */
+static u32 isp1760_hcd_read(struct usb_hcd *hcd, u32 field)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	return isp1760_field_read(priv->fields, field);
+}
+
+/*
+ * We need, in isp1763, to write directly the values to the portsc1
+ * register so it will make the other values to trigger.
+ */
+static void isp1760_hcd_portsc1_set_clear(struct isp1760_hcd *priv, u32 field,
+					  u32 val)
+{
+	u32 bit = isp1763_hc_portsc1_fields[field];
+	u32 port_status = readl(priv->base + ISP1763_HC_PORTSC1);
+
+	if (val)
+		writel(port_status | bit, priv->base + ISP1763_HC_PORTSC1);
+	else
+		writel(port_status & ~bit, priv->base + ISP1763_HC_PORTSC1);
+}
+
+static void isp1760_hcd_write(struct usb_hcd *hcd, u32 field, u32 val)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	if (unlikely(priv->is_isp1763 &&
+		     (field >= PORT_OWNER && field <= PORT_CONNECT)))
+		return isp1760_hcd_portsc1_set_clear(priv, field, val);
+
+	isp1760_field_write(priv->fields, field, val);
+}
+
+static void isp1760_hcd_set(struct usb_hcd *hcd, u32 field)
+{
+	isp1760_hcd_write(hcd, field, 0xFFFFFFFF);
+}
+
+static void isp1760_hcd_clear(struct usb_hcd *hcd, u32 field)
+{
+	isp1760_hcd_write(hcd, field, 0);
+}
+
+static int isp1760_hcd_set_and_wait(struct usb_hcd *hcd, u32 field,
+				    u32 timeout_us)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	u32 val;
+
+	isp1760_hcd_set(hcd, field);
+
+	return regmap_field_read_poll_timeout(priv->fields[field], val,
+					      val, 0, timeout_us);
+}
+
+static int isp1760_hcd_set_and_wait_swap(struct usb_hcd *hcd, u32 field,
+					 u32 timeout_us)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	u32 val;
+
+	isp1760_hcd_set(hcd, field);
+
+	return regmap_field_read_poll_timeout(priv->fields[field], val,
+					      !val, 0, timeout_us);
+}
+
+static int isp1760_hcd_clear_and_wait(struct usb_hcd *hcd, u32 field,
+				      u32 timeout_us)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	u32 val;
+
+	isp1760_hcd_clear(hcd, field);
+
+	return regmap_field_read_poll_timeout(priv->fields[field], val,
+					      !val, 0, timeout_us);
+}
+
+static bool isp1760_hcd_is_set(struct usb_hcd *hcd, u32 field)
+{
+	return !!isp1760_hcd_read(hcd, field);
+}
+
+static bool isp1760_hcd_ppc_is_set(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	if (priv->is_isp1763)
+		return true;
+
+	return isp1760_hcd_is_set(hcd, HCS_PPC);
+}
+
+static u32 isp1760_hcd_n_ports(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	if (priv->is_isp1763)
+		return 1;
+
+	return isp1760_hcd_read(hcd, HCS_N_PORTS);
+}
+
+/*
+ * Access functions for isp176x memory (offset >= 0x0400).
+ *
+ * bank_reads8() reads memory locations prefetched by an earlier write to
+ * HC_MEMORY_REG (see isp176x datasheet). Unless you want to do fancy multi-
+ * bank optimizations, you should use the more generic mem_read() below.
+ *
+ * For access to ptd memory, use the specialized ptd_read() and ptd_write()
+ * below.
+ *
+ * These functions copy via MMIO data to/from the device. memcpy_{to|from}io()
+ * doesn't quite work because some people have to enforce 32-bit access
+ */
+static void bank_reads8(void __iomem *src_base, u32 src_offset, u32 bank_addr,
+			__u32 *dst, u32 bytes)
+{
+	__u32 __iomem *src;
+	u32 val;
+	__u8 *src_byteptr;
+	__u8 *dst_byteptr;
+
+	src = src_base + (bank_addr | src_offset);
+
+	if (src_offset < PAYLOAD_OFFSET) {
+		while (bytes >= 4) {
+			*dst = readl_relaxed(src);
+			bytes -= 4;
+			src++;
+			dst++;
+		}
+	} else {
+		while (bytes >= 4) {
+			*dst = __raw_readl(src);
+			bytes -= 4;
+			src++;
+			dst++;
+		}
+	}
+
+	if (!bytes)
+		return;
+
+	/* in case we have 3, 2 or 1 by left. The dst buffer may not be fully
+	 * allocated.
+	 */
+	if (src_offset < PAYLOAD_OFFSET)
+		val = readl_relaxed(src);
+	else
+		val = __raw_readl(src);
+
+	dst_byteptr = (void *)dst;
+	src_byteptr = (void *)&val;
+	while (bytes > 0) {
+		*dst_byteptr = *src_byteptr;
+		dst_byteptr++;
+		src_byteptr++;
+		bytes--;
+	}
+}
+
+static void isp1760_mem_read(struct usb_hcd *hcd, u32 src_offset, void *dst,
+			     u32 bytes)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	isp1760_hcd_write(hcd, MEM_BANK_SEL, ISP_BANK_0);
+	isp1760_hcd_write(hcd, MEM_START_ADDR, src_offset);
+	ndelay(100);
+
+	bank_reads8(priv->base, src_offset, ISP_BANK_0, dst, bytes);
+}
+
+/*
+ * ISP1763 does not have the banks direct host controller memory access,
+ * needs to use the HC_DATA register. Add data read/write according to this,
+ * and also adjust 16bit access.
+ */
+static void isp1763_mem_read(struct usb_hcd *hcd, u16 srcaddr,
+			     u16 *dstptr, u32 bytes)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	/* Write the starting device address to the hcd memory register */
+	isp1760_reg_write(priv->regs, ISP1763_HC_MEMORY, srcaddr);
+	ndelay(100); /* Delay between consecutive access */
+
+	/* As long there are at least 16-bit to read ... */
+	while (bytes >= 2) {
+		*dstptr = __raw_readw(priv->base + ISP1763_HC_DATA);
+		bytes -= 2;
+		dstptr++;
+	}
+
+	/* If there are no more bytes to read, return */
+	if (bytes <= 0)
+		return;
+
+	*((u8 *)dstptr) = (u8)(readw(priv->base + ISP1763_HC_DATA) & 0xFF);
+}
+
+static void mem_read(struct usb_hcd *hcd, u32 src_offset, __u32 *dst,
+		     u32 bytes)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	if (!priv->is_isp1763)
+		return isp1760_mem_read(hcd, src_offset, (u16 *)dst, bytes);
+
+	isp1763_mem_read(hcd, (u16)src_offset, (u16 *)dst, bytes);
+}
+
+static void isp1760_mem_write(void __iomem *dst_base, u32 dst_offset,
+			      __u32 const *src, u32 bytes)
+{
+	__u32 __iomem *dst;
+
+	dst = dst_base + dst_offset;
+
+	if (dst_offset < PAYLOAD_OFFSET) {
+		while (bytes >= 4) {
+			writel_relaxed(*src, dst);
+			bytes -= 4;
+			src++;
+			dst++;
+		}
+	} else {
+		while (bytes >= 4) {
+			__raw_writel(*src, dst);
+			bytes -= 4;
+			src++;
+			dst++;
+		}
+	}
+
+	if (!bytes)
+		return;
+	/* in case we have 3, 2 or 1 bytes left. The buffer is allocated and the
+	 * extra bytes should not be read by the HW.
+	 */
+
+	if (dst_offset < PAYLOAD_OFFSET)
+		writel_relaxed(*src, dst);
+	else
+		__raw_writel(*src, dst);
+}
+
+static void isp1763_mem_write(struct usb_hcd *hcd, u16 dstaddr, u16 *src,
+			      u32 bytes)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	/* Write the starting device address to the hcd memory register */
+	isp1760_reg_write(priv->regs, ISP1763_HC_MEMORY, dstaddr);
+	ndelay(100); /* Delay between consecutive access */
+
+	while (bytes >= 2) {
+		/* Get and write the data; then adjust the data ptr and len */
+		__raw_writew(*src, priv->base + ISP1763_HC_DATA);
+		bytes -= 2;
+		src++;
+	}
+
+	/* If there are no more bytes to process, return */
+	if (bytes <= 0)
+		return;
+
+	/*
+	 * The only way to get here is if there is a single byte left,
+	 * get it and write it to the data reg;
+	 */
+	writew(*((u8 *)src), priv->base + ISP1763_HC_DATA);
+}
+
+static void mem_write(struct usb_hcd *hcd, u32 dst_offset, __u32 *src,
+		      u32 bytes)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	if (!priv->is_isp1763)
+		return isp1760_mem_write(priv->base, dst_offset, src, bytes);
+
+	isp1763_mem_write(hcd, dst_offset, (u16 *)src, bytes);
+}
+
+/*
+ * Read and write ptds. 'ptd_offset' should be one of ISO_PTD_OFFSET,
+ * INT_PTD_OFFSET, and ATL_PTD_OFFSET. 'slot' should be less than 32.
+ */
+static void isp1760_ptd_read(struct usb_hcd *hcd, u32 ptd_offset, u32 slot,
+			     struct ptd *ptd)
+{
+	u16 src_offset = ptd_offset + slot * sizeof(*ptd);
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	isp1760_hcd_write(hcd, MEM_BANK_SEL, ISP_BANK_0);
+	isp1760_hcd_write(hcd, MEM_START_ADDR, src_offset);
+	ndelay(90);
+
+	bank_reads8(priv->base, src_offset, ISP_BANK_0, (void *)ptd,
+		    sizeof(*ptd));
+}
+
+static void isp1763_ptd_read(struct usb_hcd *hcd, u32 ptd_offset, u32 slot,
+			     struct ptd *ptd)
+{
+	u16 src_offset = ptd_offset + slot * sizeof(*ptd);
+	struct ptd_le32 le32_ptd;
+
+	isp1763_mem_read(hcd, src_offset, (u16 *)&le32_ptd, sizeof(le32_ptd));
+	/* Normalize the data obtained */
+	ptd->dw0 = le32_to_dw(le32_ptd.dw0);
+	ptd->dw1 = le32_to_dw(le32_ptd.dw1);
+	ptd->dw2 = le32_to_dw(le32_ptd.dw2);
+	ptd->dw3 = le32_to_dw(le32_ptd.dw3);
+	ptd->dw4 = le32_to_dw(le32_ptd.dw4);
+	ptd->dw5 = le32_to_dw(le32_ptd.dw5);
+	ptd->dw6 = le32_to_dw(le32_ptd.dw6);
+	ptd->dw7 = le32_to_dw(le32_ptd.dw7);
+}
+
+static void ptd_read(struct usb_hcd *hcd, u32 ptd_offset, u32 slot,
+		     struct ptd *ptd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	if (!priv->is_isp1763)
+		return isp1760_ptd_read(hcd, ptd_offset, slot, ptd);
+
+	isp1763_ptd_read(hcd, ptd_offset, slot, ptd);
+}
+
+static void isp1763_ptd_write(struct usb_hcd *hcd, u32 ptd_offset, u32 slot,
+			      struct ptd *cpu_ptd)
+{
+	u16 dst_offset = ptd_offset + slot * sizeof(*cpu_ptd);
+	struct ptd_le32 ptd;
+
+	ptd.dw0 = dw_to_le32(cpu_ptd->dw0);
+	ptd.dw1 = dw_to_le32(cpu_ptd->dw1);
+	ptd.dw2 = dw_to_le32(cpu_ptd->dw2);
+	ptd.dw3 = dw_to_le32(cpu_ptd->dw3);
+	ptd.dw4 = dw_to_le32(cpu_ptd->dw4);
+	ptd.dw5 = dw_to_le32(cpu_ptd->dw5);
+	ptd.dw6 = dw_to_le32(cpu_ptd->dw6);
+	ptd.dw7 = dw_to_le32(cpu_ptd->dw7);
+
+	isp1763_mem_write(hcd, dst_offset,  (u16 *)&ptd.dw0,
+			  8 * sizeof(ptd.dw0));
+}
+
+static void isp1760_ptd_write(void __iomem *base, u32 ptd_offset, u32 slot,
+			      struct ptd *ptd)
+{
+	u32 dst_offset = ptd_offset + slot * sizeof(*ptd);
+
+	isp1760_mem_write(base, dst_offset + sizeof(ptd->dw0),
+			  (__force u32 *)&ptd->dw1, 7 * sizeof(ptd->dw1));
+	/*
+	 * Make sure dw0 gets written last (after other dw's and after payload)
+	 *  since it contains the enable bit
+	 */
+	wmb();
+	isp1760_mem_write(base, dst_offset, (__force u32 *)&ptd->dw0,
+			  sizeof(ptd->dw0));
+}
+
+static void ptd_write(struct usb_hcd *hcd, u32 ptd_offset, u32 slot,
+		      struct ptd *ptd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+
+	if (!priv->is_isp1763)
+		return isp1760_ptd_write(priv->base, ptd_offset, slot, ptd);
+
+	isp1763_ptd_write(hcd, ptd_offset, slot, ptd);
+}
+
+/* memory management of the 60kb on the chip from 0x1000 to 0xffff */
+static void init_memory(struct isp1760_hcd *priv)
+{
+	const struct isp1760_memory_layout *mem = priv->memory_layout;
+	int i, j, curr;
+	u32 payload_addr;
+
+	payload_addr = PAYLOAD_OFFSET;
+
+	for (i = 0, curr = 0; i < ARRAY_SIZE(mem->blocks); i++, curr += j) {
+		for (j = 0; j < mem->blocks[i]; j++) {
+			priv->memory_pool[curr + j].start = payload_addr;
+			priv->memory_pool[curr + j].size = mem->blocks_size[i];
+			priv->memory_pool[curr + j].free = 1;
+			payload_addr += priv->memory_pool[curr + j].size;
+		}
+	}
+
+	WARN_ON(payload_addr - priv->memory_pool[0].start >
+		mem->payload_area_size);
+}
+
+static void alloc_mem(struct usb_hcd *hcd, struct isp1760_qtd *qtd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	const struct isp1760_memory_layout *mem = priv->memory_layout;
+	int i;
+
+	WARN_ON(qtd->payload_addr);
+
+	if (!qtd->length)
+		return;
+
+	for (i = 0; i < mem->payload_blocks; i++) {
+		if (priv->memory_pool[i].size >= qtd->length &&
+		    priv->memory_pool[i].free) {
+			priv->memory_pool[i].free = 0;
+			qtd->payload_addr = priv->memory_pool[i].start;
+			return;
+		}
+	}
+}
+
+static void free_mem(struct usb_hcd *hcd, struct isp1760_qtd *qtd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	const struct isp1760_memory_layout *mem = priv->memory_layout;
+	int i;
+
+	if (!qtd->payload_addr)
+		return;
+
+	for (i = 0; i < mem->payload_blocks; i++) {
+		if (priv->memory_pool[i].start == qtd->payload_addr) {
+			WARN_ON(priv->memory_pool[i].free);
+			priv->memory_pool[i].free = 1;
+			qtd->payload_addr = 0;
+			return;
+		}
+	}
+
+	WARN_ON(1);
+	qtd->payload_addr = 0;
+}
+
+/* reset a non-running (STS_HALT == 1) controller */
+static int ehci_reset(struct usb_hcd *hcd)
+{
+	return isp1760_hcd_set_and_wait_swap(hcd, CMD_RESET, 250 * 1000);
+}
+
+static struct isp1760_qh *qh_alloc(gfp_t flags)
+{
+	struct isp1760_qh *qh;
+
+	qh = kmem_cache_alloc(qh_cachep, flags);
+	if (!qh)
+		return NULL;
+
+	memset(qh, '\0', qh_cachep->sz);
+	INIT_LIST_HEAD(&qh->qh_list);
+	INIT_LIST_HEAD(&qh->qtd_list);
+	qh->slot = -1;
+
+	return qh;
+}
+
+static void qh_free(struct isp1760_qh *qh)
+{
+	WARN_ON(!list_empty(&qh->qtd_list));
+	WARN_ON(qh->slot > -1);
+	kmem_cache_free(qh_cachep, qh);
+}
+
+/* one-time init, only for memory state */
+static int priv_init(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	u32 isoc_cache;
+	u32 isoc_thres;
+	int i;
+
+	for (i = 0; i < QH_END; i++)
+		INIT_LIST_HEAD(&priv->qh_list[i]);
+
+	/*
+	 * hw default: 1K periodic list heads, one per frame.
+	 * periodic_size can shrink by USBCMD update if hcc_params allows.
+	 */
+	priv->periodic_size = DEFAULT_I_TDPS;
+
+	if (priv->is_isp1763) {
+		priv->i_thresh = 2;
+		return 0;
+	}
+
+	/* controllers may cache some of the periodic schedule ... */
+	isoc_cache = isp1760_hcd_read(hcd, HCC_ISOC_CACHE);
+	isoc_thres = isp1760_hcd_read(hcd, HCC_ISOC_THRES);
+
+	/* full frame cache */
+	if (isoc_cache)
+		priv->i_thresh = 8;
+	else /* N microframes cached */
+		priv->i_thresh = 2 + isoc_thres;
+
+	return 0;
+}
+
+static int isp1760_hc_setup(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	u32 atx_reset;
+	int result;
+	u32 scratch;
+	u32 pattern;
+
+	if (priv->is_isp1763)
+		pattern = 0xcafe;
+	else
+		pattern = 0xdeadcafe;
+
+	isp1760_hcd_write(hcd, HC_SCRATCH, pattern);
+
+	/* Change bus pattern */
+	isp1760_hcd_read(hcd, HC_CHIP_ID_HIGH);
+	scratch = isp1760_hcd_read(hcd, HC_SCRATCH);
+	if (scratch != pattern) {
+		printf("Scratch test failed. 0x%08x\n", scratch);
+		return -ENODEV;
+	}
+
+	/*
+	 * The RESET_HC bit in the SW_RESET register is supposed to reset the
+	 * host controller without touching the CPU interface registers, but at
+	 * least on the ISP1761 it seems to behave as the RESET_ALL bit and
+	 * reset the whole device. We thus can't use it here, so let's reset
+	 * the host controller through the EHCI USB Command register. The device
+	 * has been reset in core code anyway, so this shouldn't matter.
+	 */
+	isp1760_hcd_clear(hcd, ISO_BUF_FILL);
+	isp1760_hcd_clear(hcd, INT_BUF_FILL);
+	isp1760_hcd_clear(hcd, ATL_BUF_FILL);
+
+	isp1760_hcd_set(hcd, HC_ATL_PTD_SKIPMAP);
+	isp1760_hcd_set(hcd, HC_INT_PTD_SKIPMAP);
+	isp1760_hcd_set(hcd, HC_ISO_PTD_SKIPMAP);
+
+	result = ehci_reset(hcd);
+	if (result)
+		return result;
+
+	/* Step 11 passed */
+
+	/* ATL reset */
+	if (priv->is_isp1763)
+		atx_reset = SW_RESET_RESET_ATX;
+	else
+		atx_reset = ALL_ATX_RESET;
+
+	isp1760_hcd_set(hcd, atx_reset);
+	mdelay(10);
+	isp1760_hcd_clear(hcd, atx_reset);
+
+	if (priv->is_isp1763) {
+		isp1760_hcd_set(hcd, HW_OTG_DISABLE);
+		isp1760_hcd_set(hcd, HW_SW_SEL_HC_DC_CLEAR);
+		isp1760_hcd_set(hcd, HW_HC_2_DIS_CLEAR);
+		isp1760_hcd_set(hcd, HW_DM_PULLDOWN);
+		isp1760_hcd_set(hcd, HW_DP_PULLDOWN);
+		mdelay(10);
+
+		isp1760_hcd_set(hcd, HW_INTF_LOCK);
+	}
+
+	isp1760_hcd_set(hcd, HC_INT_IRQ_ENABLE);
+	isp1760_hcd_set(hcd, HC_ATL_IRQ_ENABLE);
+
+	return priv_init(hcd);
+}
+
+static u32 base_to_chip(u32 base)
+{
+	return ((base - 0x400) >> 3);
+}
+
+static int last_qtd_of_urb(struct isp1760_qtd *qtd, struct isp1760_qh *qh)
+{
+	struct urb *urb;
+
+	if (list_is_last(&qtd->qtd_list, &qh->qtd_list))
+		return 1;
+
+	urb = qtd->urb;
+	qtd = list_entry(qtd->qtd_list.next, typeof(*qtd), qtd_list);
+
+	return (qtd->urb != urb);
+}
+
+/* magic numbers that can affect system performance */
+#define	EHCI_TUNE_CERR		3	/* 0-3 qtd retries; 0 == don't stop */
+#define	EHCI_TUNE_RL_HS		4	/* nak throttle; see 4.9 */
+#define	EHCI_TUNE_RL_TT		0
+#define	EHCI_TUNE_MULT_HS	1	/* 1-3 transactions/uframe; 4.10.3 */
+#define	EHCI_TUNE_MULT_TT	1
+#define	EHCI_TUNE_FLS		2	/* (small) 256 frame schedule */
+
+static void create_ptd_atl(struct isp1760_qh *qh, struct isp1760_qtd *qtd,
+			   struct ptd *ptd)
+{
+	u32 maxpacket;
+	u32 multi;
+	u32 rl = RL_COUNTER;
+	u32 nak = NAK_COUNTER;
+	u8 portnr;
+	u8 hubaddr;
+
+	memset(ptd, 0, sizeof(*ptd));
+
+	/* according to 3.6.2, max packet len can not be > 0x400 */
+	maxpacket = usb_maxpacket(qtd->urb->dev, qtd->urb->pipe);
+	multi =  1 + ((maxpacket >> 11) & 0x3);
+	maxpacket &= 0x7ff;
+
+	/* DW0 */
+	ptd->dw0 = DW0_VALID_BIT;
+	ptd->dw0 |= TO_DW0_LENGTH(qtd->length);
+	ptd->dw0 |= TO_DW0_MAXPACKET(maxpacket);
+	ptd->dw0 |= TO_DW0_ENDPOINT(usb_pipeendpoint(qtd->urb->pipe));
+
+	/* DW1 */
+	ptd->dw1 = TO_DW((usb_pipeendpoint(qtd->urb->pipe) >> 1));
+	ptd->dw1 |= TO_DW1_DEVICE_ADDR(usb_pipedevice(qtd->urb->pipe));
+	ptd->dw1 |= TO_DW1_PID_TOKEN(qtd->packet_type);
+
+	if (usb_pipebulk(qtd->urb->pipe))
+		ptd->dw1 |= DW1_TRANS_BULK;
+	else if  (usb_pipeint(qtd->urb->pipe))
+		ptd->dw1 |= DW1_TRANS_INT;
+
+	if (qtd->urb->dev->speed != USB_SPEED_HIGH) {
+		/* split transaction */
+
+		ptd->dw1 |= DW1_TRANS_SPLIT;
+		if (qtd->urb->dev->speed == USB_SPEED_LOW)
+			ptd->dw1 |= DW1_SE_USB_LOSPEED;
+
+		if (!qtd->urb->dev->dev->parent_priv_) {
+			portnr = qtd->urb->dev->portnr;
+			hubaddr = qtd->urb->dev->devnum;
+		} else {
+			usb_find_usb2_hub_address_port(qtd->urb->dev, &hubaddr,
+						       &portnr);
+		}
+
+		ptd->dw1 |= TO_DW1_PORT_NUM(portnr);
+		ptd->dw1 |= TO_DW1_HUB_NUM(hubaddr);
+
+		/* SE bit for Split INT transfers */
+		if (usb_pipeint(qtd->urb->pipe) &&
+		    qtd->urb->dev->speed == USB_SPEED_LOW)
+			ptd->dw1 |= DW1_SE_USB_LOSPEED;
+
+		rl = 0;
+		nak = 0;
+	} else {
+		ptd->dw0 |= TO_DW0_MULTI(multi);
+		if (usb_pipecontrol(qtd->urb->pipe) ||
+		    usb_pipebulk(qtd->urb->pipe))
+			ptd->dw3 |= TO_DW3_PING(qh->ping);
+	}
+	/* DW2 */
+	ptd->dw2 = 0;
+	ptd->dw2 |= TO_DW2_DATA_START_ADDR(base_to_chip(qtd->payload_addr));
+	ptd->dw2 |= TO_DW2_RL(rl);
+
+	/* DW3 */
+	ptd->dw3 |= TO_DW3_NAKCOUNT(nak);
+	ptd->dw3 |= TO_DW3_DATA_TOGGLE(qh->toggle);
+
+	if (usb_pipecontrol(qtd->urb->pipe)) {
+		if (qtd->data_buffer == qtd->urb->setup_packet)
+			ptd->dw3 &= ~TO_DW3_DATA_TOGGLE(1);
+		else if (last_qtd_of_urb(qtd, qh))
+			ptd->dw3 |= TO_DW3_DATA_TOGGLE(1);
+	}
+
+	ptd->dw3 |= DW3_ACTIVE_BIT;
+	/* Cerr */
+	ptd->dw3 |= TO_DW3_CERR(ERR_COUNTER);
+}
+
+static void transform_add_int(struct isp1760_qh *qh, struct isp1760_qtd *qtd,
+			      struct ptd *ptd)
+{
+	struct usb_host_endpoint *hep = qtd->urb->ep;
+	struct usb_endpoint_descriptor *epd = &hep->desc;
+	u32 usof;
+	u32 period;
+
+	/*
+	 * Most of this is guessing. ISP1761 datasheet is quite unclear, and
+	 * the algorithm from the original Philips driver code, which was
+	 * pretty much used in this driver before as well, is quite horrendous
+	 * and, i believe, incorrect. The code below follows the datasheet and
+	 * USB2.0 spec as far as I can tell, and plug/unplug seems to be much
+	 * more reliable this way (fingers crossed...).
+	 */
+
+	if (qtd->urb->dev->speed == USB_SPEED_HIGH) {
+		/* urb->interval is in units of microframes (1/8 ms) */
+		period = epd->bInterval >> 3;
+
+		if (epd->bInterval > 4)
+			usof = 0x01; /* One bit set => interval 1 ms * uFrame-match */
+		else if (epd->bInterval > 2)
+			usof = 0x22; /* Two bits set => interval 1/2 ms */
+		else if (epd->bInterval > 1)
+			usof = 0x55; /* Four bits set => interval 1/4 ms */
+		else
+			usof = 0xff; /* All bits set => interval 1/8 ms */
+	} else {
+		/* urb->interval is in units of frames (1 ms) */
+		period = epd->bInterval;
+		/* Execute Start Split on any of the four first uFrames */
+		usof = 0x0f;
+
+		/*
+		 * First 8 bits in dw5 is uSCS and "specifies which uSOF the
+		 * complete split needs to be sent. Valid only for IN." Also,
+		 * "All bits can be set to one for every transfer." (p 82,
+		 * ISP1761 data sheet.) 0x1c is from Philips driver. Where did
+		 * that number come from? 0xff seems to work fine...
+		 */
+		/* Execute Complete Split on any uFrame */
+		ptd->dw5 = TO_DW(0xff);
+	}
+
+	/* Ensure equal or shorter period than requested */
+	period = period >> 1;
+	/* Mask off too large values and lowest unused 3 bits */
+	period &= 0xf8;
+
+	ptd->dw2 |= TO_DW(period);
+	ptd->dw4 = TO_DW(usof);
+}
+
+static void create_ptd_int(struct isp1760_qh *qh, struct isp1760_qtd *qtd,
+			   struct ptd *ptd)
+{
+	create_ptd_atl(qh, qtd, ptd);
+	transform_add_int(qh, qtd, ptd);
+}
+
+static void isp1760_urb_done(struct usb_hcd *hcd, struct urb *urb)
+{
+	if (usb_pipein(urb->pipe) && usb_pipetype(urb->pipe) != PIPE_CONTROL) {
+		void *ptr;
+
+		for (ptr = urb->transfer_buffer;
+		     ptr < urb->transfer_buffer + urb->transfer_buffer_length;
+		     ptr += PAGE_SIZE)
+			flush_dcache_range((unsigned  long)ptr,
+					   (unsigned long)ptr + PAGE_SIZE);
+	}
+
+	/* complete() can reenter this HCD */
+	usb_hcd_unlink_urb_from_ep(hcd, urb);
+	usb_hcd_giveback_urb(hcd, urb, urb->status);
+}
+
+static struct isp1760_qtd *qtd_alloc(gfp_t flags, struct urb *urb,
+				     u8 packet_type)
+{
+	struct isp1760_qtd *qtd;
+
+	qtd = kmem_cache_alloc(qtd_cachep, flags);
+	if (!qtd)
+		return NULL;
+
+	memset(qtd, '\0', sizeof(*qtd));
+	INIT_LIST_HEAD(&qtd->qtd_list);
+	qtd->urb = urb;
+	qtd->packet_type = packet_type;
+	qtd->status = QTD_ENQUEUED;
+	qtd->actual_length = 0;
+
+	return qtd;
+}
+
+static void qtd_free(struct isp1760_qtd *qtd)
+{
+	WARN_ON(qtd->payload_addr);
+	kmem_cache_free(qtd_cachep, qtd);
+}
+
+static void start_bus_transfer(struct usb_hcd *hcd, u32 ptd_offset, int slot,
+			       struct isp1760_slotinfo *slots,
+			       struct isp1760_qtd *qtd, struct isp1760_qh *qh,
+			       struct ptd *ptd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	const struct isp1760_memory_layout *mem = priv->memory_layout;
+	int skip_map;
+
+	WARN_ON((slot < 0) || (slot > mem->slot_num - 1));
+	WARN_ON(qtd->length && !qtd->payload_addr);
+	WARN_ON(slots[slot].qtd);
+	WARN_ON(slots[slot].qh);
+	WARN_ON(qtd->status != QTD_PAYLOAD_ALLOC);
+
+	if (priv->is_isp1763)
+		ndelay(100);
+
+	/* Make sure done map has not triggered from some unlinked transfer */
+	if (ptd_offset == ATL_PTD_OFFSET) {
+		skip_map = isp1760_hcd_read(hcd, HC_ATL_PTD_SKIPMAP);
+		isp1760_hcd_write(hcd, HC_ATL_PTD_SKIPMAP,
+				  skip_map | (1 << slot));
+		priv->atl_done_map |= isp1760_hcd_read(hcd, HC_ATL_PTD_DONEMAP);
+		priv->atl_done_map &= ~(1 << slot);
+	} else {
+		skip_map = isp1760_hcd_read(hcd, HC_INT_PTD_SKIPMAP);
+		isp1760_hcd_write(hcd, HC_INT_PTD_SKIPMAP,
+				  skip_map | (1 << slot));
+		priv->int_done_map |= isp1760_hcd_read(hcd, HC_INT_PTD_DONEMAP);
+		priv->int_done_map &= ~(1 << slot);
+	}
+
+	skip_map &= ~(1 << slot);
+	qh->slot = slot;
+	qtd->status = QTD_XFER_STARTED;
+	slots[slot].qtd = qtd;
+	slots[slot].qh = qh;
+
+	ptd_write(hcd, ptd_offset, slot, ptd);
+
+	if (ptd_offset == ATL_PTD_OFFSET)
+		isp1760_hcd_write(hcd, HC_ATL_PTD_SKIPMAP, skip_map);
+	else
+		isp1760_hcd_write(hcd, HC_INT_PTD_SKIPMAP, skip_map);
+}
+
+static int is_short_bulk(struct isp1760_qtd *qtd)
+{
+	return (usb_pipebulk(qtd->urb->pipe) &&
+		(qtd->actual_length < qtd->length));
+}
+
+static void collect_qtds(struct usb_hcd *hcd, struct isp1760_qh *qh,
+			 struct list_head *urb_list)
+{
+	struct isp1760_qtd *qtd, *qtd_next;
+	struct urb_listitem *urb_listitem;
+	int last_qtd;
+
+	list_for_each_entry_safe(qtd, qtd_next, &qh->qtd_list, qtd_list) {
+		if (qtd->status < QTD_XFER_COMPLETE)
+			break;
+
+		last_qtd = last_qtd_of_urb(qtd, qh);
+
+		if (!last_qtd && qtd->status == QTD_RETIRE)
+			qtd_next->status = QTD_RETIRE;
+
+		if (qtd->status == QTD_XFER_COMPLETE) {
+			if (qtd->actual_length) {
+				switch (qtd->packet_type) {
+				case IN_PID:
+					mem_read(hcd, qtd->payload_addr,
+						 qtd->data_buffer,
+						 qtd->actual_length);
+					fallthrough;
+				case OUT_PID:
+					qtd->urb->actual_length +=
+							qtd->actual_length;
+					fallthrough;
+				case SETUP_PID:
+					break;
+				}
+			}
+
+			if (is_short_bulk(qtd)) {
+				if (qtd->urb->transfer_flags & URB_SHORT_NOT_OK)
+					qtd->urb->status = -EREMOTEIO;
+				if (!last_qtd)
+					qtd_next->status = QTD_RETIRE;
+			}
+		}
+
+		if (qtd->payload_addr)
+			free_mem(hcd, qtd);
+
+		if (last_qtd) {
+			if (qtd->status == QTD_RETIRE &&
+			    qtd->urb->status == -EINPROGRESS)
+				qtd->urb->status = -EPIPE;
+
+			/* Defer calling of urb_done() since it releases lock */
+			urb_listitem = kmem_cache_alloc(urb_listitem_cachep,
+							GFP_ATOMIC);
+			if (unlikely(!urb_listitem))
+				break; /* Try again on next call */
+			urb_listitem->urb = qtd->urb;
+			list_add_tail(&urb_listitem->urb_list, urb_list);
+		}
+
+		list_del(&qtd->qtd_list);
+		qtd_free(qtd);
+	}
+}
+
+#define ENQUEUE_DEPTH	2
+static void enqueue_qtds(struct usb_hcd *hcd, struct isp1760_qh *qh)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	const struct isp1760_memory_layout *mem = priv->memory_layout;
+	int slot_num = mem->slot_num;
+	int ptd_offset;
+	struct isp1760_slotinfo *slots;
+	int curr_slot, free_slot;
+	int n;
+	struct ptd ptd;
+	struct isp1760_qtd *qtd;
+
+	if (unlikely(list_empty(&qh->qtd_list)))
+		return;
+
+	/* Make sure this endpoint's TT buffer is clean before queueing ptds */
+	if (qh->tt_buffer_dirty)
+		return;
+
+	if (usb_pipeint(list_entry(qh->qtd_list.next, struct isp1760_qtd,
+				   qtd_list)->urb->pipe)) {
+		ptd_offset = INT_PTD_OFFSET;
+		slots = priv->int_slots;
+	} else {
+		ptd_offset = ATL_PTD_OFFSET;
+		slots = priv->atl_slots;
+	}
+
+	free_slot = -1;
+	for (curr_slot = 0; curr_slot < slot_num; curr_slot++) {
+		if (free_slot == -1 && !slots[curr_slot].qtd)
+			free_slot = curr_slot;
+		if (slots[curr_slot].qh == qh)
+			break;
+	}
+
+	n = 0;
+	list_for_each_entry(qtd, &qh->qtd_list, qtd_list) {
+		if (qtd->status == QTD_ENQUEUED) {
+			WARN_ON(qtd->payload_addr);
+			alloc_mem(hcd, qtd);
+			if (qtd->length && !qtd->payload_addr)
+				break;
+
+			if (qtd->length && (qtd->packet_type == SETUP_PID ||
+					    qtd->packet_type == OUT_PID)) {
+				mem_write(hcd, qtd->payload_addr,
+					  qtd->data_buffer, qtd->length);
+			}
+
+			qtd->status = QTD_PAYLOAD_ALLOC;
+		}
+
+		if (qtd->status == QTD_PAYLOAD_ALLOC) {
+			/* Start xfer for this endpoint if not already done */
+			if ((curr_slot > slot_num - 1) && (free_slot > -1)) {
+				if (usb_pipeint(qtd->urb->pipe))
+					create_ptd_int(qh, qtd, &ptd);
+				else
+					create_ptd_atl(qh, qtd, &ptd);
+
+				start_bus_transfer(hcd, ptd_offset, free_slot,
+						   slots, qtd, qh, &ptd);
+				curr_slot = free_slot;
+			}
+
+			n++;
+			if (n >= ENQUEUE_DEPTH)
+				break;
+		}
+	}
+}
+
+static void schedule_ptds(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv;
+	struct isp1760_qh *qh, *qh_next;
+	struct list_head *ep_queue;
+	LIST_HEAD(urb_list);
+	struct urb_listitem *urb_listitem, *urb_listitem_next;
+	int i;
+
+	if (!hcd) {
+		WARN_ON(1);
+		return;
+	}
+
+	priv = hcd_to_priv(hcd);
+
+	/*
+	 * check finished/retired xfers, transfer payloads, call urb_done()
+	 */
+	for (i = 0; i < QH_END; i++) {
+		ep_queue = &priv->qh_list[i];
+		list_for_each_entry_safe(qh, qh_next, ep_queue, qh_list)
+			collect_qtds(hcd, qh, &urb_list);
+	}
+
+	list_for_each_entry_safe(urb_listitem, urb_listitem_next, &urb_list,
+				 urb_list) {
+		isp1760_urb_done(hcd, urb_listitem->urb);
+		kmem_cache_free(urb_listitem_cachep, urb_listitem);
+	}
+
+	/*
+	 * Schedule packets for transfer.
+	 *
+	 * According to USB2.0 specification:
+	 *
+	 * 1st prio: interrupt xfers, up to 80 % of bandwidth
+	 * 2nd prio: control xfers
+	 * 3rd prio: bulk xfers
+	 *
+	 * ... but let's use a simpler scheme here (mostly because ISP1761 doc
+	 * is very unclear on how to prioritize traffic):
+	 *
+	 * 1) Enqueue any queued control transfers, as long as payload chip mem
+	 *    and PTD ATL slots are available.
+	 * 2) Enqueue any queued INT transfers, as long as payload chip mem
+	 *    and PTD INT slots are available.
+	 * 3) Enqueue any queued bulk transfers, as long as payload chip mem
+	 *    and PTD ATL slots are available.
+	 *
+	 * Use double buffering (ENQUEUE_DEPTH==2) as a compromise between
+	 * conservation of chip mem and performance.
+	 *
+	 * I'm sure this scheme could be improved upon!
+	 */
+	for (i = 0; i < QH_END; i++) {
+		ep_queue = &priv->qh_list[i];
+		list_for_each_entry_safe(qh, qh_next, ep_queue, qh_list)
+			enqueue_qtds(hcd, qh);
+	}
+}
+
+#define PTD_STATE_QTD_DONE	1
+#define PTD_STATE_QTD_RELOAD	2
+#define PTD_STATE_URB_RETIRE	3
+
+static int check_int_transfer(struct usb_hcd *hcd, struct ptd *ptd,
+			      struct urb *urb)
+{
+	u32 dw4;
+	int i;
+
+	dw4 = TO_U32(ptd->dw4);
+	dw4 >>= 8;
+
+	/*
+	 * FIXME: ISP1761 datasheet does not say what to do with these. Do we
+	 * need to handle these errors? Is it done in hardware?
+	 */
+	if (ptd->dw3 & DW3_HALT_BIT) {
+		urb->status = -EPROTO; /* Default unknown error */
+
+		for (i = 0; i < 8; i++) {
+			switch (dw4 & 0x7) {
+			case INT_UNDERRUN:
+				printf("underrun during uFrame %d\n", i);
+				urb->status = -ECOMM; /* Could not write data */
+				break;
+			case INT_EXACT:
+				printf("transaction error uFrame %d\n", i);
+				/* timeout, bad CRC, PID error etc. */
+				urb->status = -EPROTO;
+				break;
+			case INT_BABBLE:
+				printf("babble error during uFrame %d\n", i);
+				urb->status = -EOVERFLOW;
+				break;
+			}
+			dw4 >>= 3;
+		}
+
+		return PTD_STATE_URB_RETIRE;
+	}
+
+	return PTD_STATE_QTD_DONE;
+}
+
+static int check_atl_transfer(struct usb_hcd *hcd, struct ptd *ptd,
+			      struct urb *urb)
+{
+	WARN_ON(!ptd);
+	if (ptd->dw3 & DW3_HALT_BIT) {
+		if (ptd->dw3 & DW3_BABBLE_BIT)
+			urb->status = -EOVERFLOW;
+		else if (FROM_DW3_CERR(ptd->dw3))
+			urb->status = -EPIPE;  /* Stall */
+		else
+			urb->status = -EPROTO; /* Unknown */
+
+		/*
+		 * useful debug
+		 * printf("%s: ptd error:\n"
+		 * "        dw0: %08x dw1: %08x dw2: %08x dw3: %08x\n"
+		 * "        dw4: %08x dw5: %08x dw6: %08x dw7: %08x\n",
+		 * __func__,
+		 * ptd->dw0, ptd->dw1, ptd->dw2, ptd->dw3,
+		 * ptd->dw4, ptd->dw5, ptd->dw6, ptd->dw7);
+		 */
+
+		return PTD_STATE_URB_RETIRE;
+	}
+
+	/* Transfer Error, *but* active and no HALT -> reload */
+	if ((ptd->dw3 & DW3_ERROR_BIT) && (ptd->dw3 & DW3_ACTIVE_BIT))
+		return PTD_STATE_QTD_RELOAD;
+
+	/*
+	 * NAKs are handled in HW by the chip. Usually if the
+	 * device is not able to send data fast enough.
+	 * This happens mostly on slower hardware.
+	 */
+	if (!FROM_DW3_NAKCOUNT(ptd->dw3) && (ptd->dw3 & DW3_ACTIVE_BIT))
+		return PTD_STATE_QTD_RELOAD;
+
+	return PTD_STATE_QTD_DONE;
+}
+
+static void handle_done_ptds(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	struct isp1760_slotinfo *slots;
+	struct isp1760_qtd *qtd;
+	struct isp1760_qh *qh;
+	struct ptd ptd;
+	u32 ptd_offset;
+	int modified;
+	int skip_map;
+	int state;
+	int slot;
+
+	skip_map = isp1760_hcd_read(hcd, HC_INT_PTD_SKIPMAP);
+	priv->int_done_map &= ~skip_map;
+	skip_map = isp1760_hcd_read(hcd, HC_ATL_PTD_SKIPMAP);
+	priv->atl_done_map &= ~skip_map;
+
+	modified = priv->int_done_map || priv->atl_done_map;
+
+	while (priv->int_done_map || priv->atl_done_map) {
+		if (priv->int_done_map) {
+			/* INT ptd */
+			slot = __ffs(priv->int_done_map);
+			priv->int_done_map &= ~(1 << slot);
+			slots = priv->int_slots;
+			/*
+			 * This should not trigger, and could be removed if
+			 * noone have any problems with it triggering:
+			 */
+			if (!slots[slot].qh) {
+				WARN_ON(1);
+				continue;
+			}
+			ptd_offset = INT_PTD_OFFSET;
+			ptd_read(hcd, INT_PTD_OFFSET, slot, &ptd);
+			state = check_int_transfer(hcd, &ptd,
+						   slots[slot].qtd->urb);
+		} else {
+			/* ATL ptd */
+			slot = __ffs(priv->atl_done_map);
+			priv->atl_done_map &= ~(1 << slot);
+			slots = priv->atl_slots;
+			/*
+			 * This should not trigger, and could be removed if
+			 * noone have any problems with it triggering:
+			 */
+			if (!slots[slot].qh) {
+				WARN_ON(1);
+				continue;
+			}
+			ptd_offset = ATL_PTD_OFFSET;
+			ptd_read(hcd, ATL_PTD_OFFSET, slot, &ptd);
+			state = check_atl_transfer(hcd, &ptd,
+						   slots[slot].qtd->urb);
+		}
+
+		qtd = slots[slot].qtd;
+		slots[slot].qtd = NULL;
+		qh = slots[slot].qh;
+		slots[slot].qh = NULL;
+		qh->slot = -1;
+
+		WARN_ON(qtd->status != QTD_XFER_STARTED);
+
+		switch (state) {
+		case PTD_STATE_QTD_DONE:
+			if (usb_pipeint(qtd->urb->pipe) &&
+			    qtd->urb->dev->speed != USB_SPEED_HIGH)
+				qtd->actual_length =
+				       FROM_DW3_SCS_NRBYTESTRANSFERRED(ptd.dw3);
+			else
+				qtd->actual_length =
+					FROM_DW3_NRBYTESTRANSFERRED(ptd.dw3);
+
+			qtd->status = QTD_XFER_COMPLETE;
+
+			if (list_is_last(&qtd->qtd_list, &qh->qtd_list) ||
+			    is_short_bulk(qtd))
+				qtd = NULL;
+			else
+				qtd = list_entry(qtd->qtd_list.next,
+						 typeof(*qtd), qtd_list);
+
+			qh->toggle = FROM_DW3_DATA_TOGGLE(ptd.dw3);
+			qh->ping = FROM_DW3_PING(ptd.dw3);
+
+			break;
+
+		case PTD_STATE_QTD_RELOAD: /* QTD_RETRY, for atls only */
+			qtd->status = QTD_PAYLOAD_ALLOC;
+			ptd.dw0 |= DW0_VALID_BIT;
+			/* RL counter = ERR counter */
+			ptd.dw3 &= ~TO_DW3_NAKCOUNT(0xf);
+			ptd.dw3 |= TO_DW3_NAKCOUNT(FROM_DW2_RL(ptd.dw2));
+			ptd.dw3 &= ~TO_DW3_CERR(3);
+			ptd.dw3 |= TO_DW3_CERR(ERR_COUNTER);
+
+			qh->toggle = FROM_DW3_DATA_TOGGLE(ptd.dw3);
+			qh->ping = FROM_DW3_PING(ptd.dw3);
+			break;
+
+		case PTD_STATE_URB_RETIRE:
+			qtd->status = QTD_RETIRE;
+			qtd = NULL;
+			qh->toggle = 0;
+			qh->ping = 0;
+			break;
+
+		default:
+			WARN_ON(1);
+			continue;
+		}
+
+		if (qtd && qtd->status == QTD_PAYLOAD_ALLOC) {
+			if (slots == priv->int_slots) {
+				if (state == PTD_STATE_QTD_RELOAD)
+					dev_err(priv->dev,
+						"PTD_STATE_QTD_RELOAD on interrupt packet\n");
+				if (state != PTD_STATE_QTD_RELOAD)
+					create_ptd_int(qh, qtd, &ptd);
+			} else {
+				if (state != PTD_STATE_QTD_RELOAD)
+					create_ptd_atl(qh, qtd, &ptd);
+			}
+
+			start_bus_transfer(hcd, ptd_offset, slot, slots, qtd,
+					   qh, &ptd);
+		}
+	}
+
+	if (modified)
+		schedule_ptds(hcd);
+}
+
+static irqreturn_t isp1760_irq(int irq, void *__hci)
+{
+	struct usb_hcd *hcd = __hci;
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	irqreturn_t irqret = IRQ_NONE;
+	u32 int_reg;
+	u32 imask;
+
+	imask = isp1760_hcd_read(hcd, HC_INTERRUPT);
+	if (unlikely(!imask))
+		return irqret;
+
+	int_reg = priv->is_isp1763 ? ISP1763_HC_INTERRUPT :
+		ISP176x_HC_INTERRUPT;
+	isp1760_reg_write(priv->regs, int_reg, imask);
+
+	priv->int_done_map |= isp1760_hcd_read(hcd, HC_INT_PTD_DONEMAP);
+	priv->atl_done_map |= isp1760_hcd_read(hcd, HC_ATL_PTD_DONEMAP);
+
+	handle_done_ptds(hcd);
+
+	irqret = IRQ_HANDLED;
+
+	return irqret;
+}
+
+static int isp1763_run(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	int retval;
+	u32 chipid_h;
+	u32 chipid_l;
+	u32 chip_rev;
+	u32 ptd_atl_int;
+	u32 ptd_iso;
+
+	chipid_h = isp1760_hcd_read(hcd, HC_CHIP_ID_HIGH);
+	chipid_l = isp1760_hcd_read(hcd, HC_CHIP_ID_LOW);
+	chip_rev = isp1760_hcd_read(hcd, HC_CHIP_REV);
+	printf("USB ISP %02x%02x HW rev. %d started\n", chipid_h,
+	       chipid_l, chip_rev);
+
+	isp1760_hcd_clear(hcd, ISO_BUF_FILL);
+	isp1760_hcd_clear(hcd, INT_BUF_FILL);
+	isp1760_hcd_clear(hcd, ATL_BUF_FILL);
+
+	isp1760_hcd_set(hcd, HC_ATL_PTD_SKIPMAP);
+	isp1760_hcd_set(hcd, HC_INT_PTD_SKIPMAP);
+	isp1760_hcd_set(hcd, HC_ISO_PTD_SKIPMAP);
+	ndelay(100);
+	isp1760_hcd_clear(hcd, HC_ATL_PTD_DONEMAP);
+	isp1760_hcd_clear(hcd, HC_INT_PTD_DONEMAP);
+	isp1760_hcd_clear(hcd, HC_ISO_PTD_DONEMAP);
+
+	isp1760_hcd_set(hcd, HW_OTG_DISABLE);
+	isp1760_reg_write(priv->regs, ISP1763_HC_OTG_CTRL_CLEAR, BIT(7));
+	isp1760_reg_write(priv->regs, ISP1763_HC_OTG_CTRL_CLEAR, BIT(15));
+	mdelay(10);
+
+	isp1760_hcd_set(hcd, HC_INT_IRQ_ENABLE);
+	isp1760_hcd_set(hcd, HC_ATL_IRQ_ENABLE);
+
+	isp1760_hcd_set(hcd, HW_GLOBAL_INTR_EN);
+
+	isp1760_hcd_clear(hcd, HC_ATL_IRQ_MASK_AND);
+	isp1760_hcd_clear(hcd, HC_INT_IRQ_MASK_AND);
+	isp1760_hcd_clear(hcd, HC_ISO_IRQ_MASK_AND);
+
+	isp1760_hcd_set(hcd, HC_ATL_IRQ_MASK_OR);
+	isp1760_hcd_set(hcd, HC_INT_IRQ_MASK_OR);
+	isp1760_hcd_set(hcd, HC_ISO_IRQ_MASK_OR);
+
+	ptd_atl_int = 0x8000;
+	ptd_iso = 0x0001;
+
+	isp1760_hcd_write(hcd, HC_ATL_PTD_LASTPTD, ptd_atl_int);
+	isp1760_hcd_write(hcd, HC_INT_PTD_LASTPTD, ptd_atl_int);
+	isp1760_hcd_write(hcd, HC_ISO_PTD_LASTPTD, ptd_iso);
+
+	isp1760_hcd_set(hcd, ATL_BUF_FILL);
+	isp1760_hcd_set(hcd, INT_BUF_FILL);
+
+	isp1760_hcd_clear(hcd, CMD_LRESET);
+	isp1760_hcd_clear(hcd, CMD_RESET);
+
+	retval = isp1760_hcd_set_and_wait(hcd, CMD_RUN, 250 * 1000);
+	if (retval)
+		return retval;
+
+	down_write(&ehci_cf_port_reset_rwsem);
+	retval = isp1760_hcd_set_and_wait(hcd, FLAG_CF, 250 * 1000);
+	up_write(&ehci_cf_port_reset_rwsem);
+	if (retval)
+		return retval;
+
+	return 0;
+}
+
+static int isp1760_run(struct usb_hcd *hcd)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	int retval;
+	u32 chipid_h;
+	u32 chipid_l;
+	u32 chip_rev;
+	u32 ptd_atl_int;
+	u32 ptd_iso;
+
+	/*
+	 * ISP1763 have some differences in the setup and order to enable
+	 * the ports, disable otg, setup buffers, and ATL, INT, ISO status.
+	 * So, just handle it a separate sequence.
+	 */
+	if (priv->is_isp1763)
+		return isp1763_run(hcd);
+
+	/* Set PTD interrupt AND & OR maps */
+	isp1760_hcd_clear(hcd, HC_ATL_IRQ_MASK_AND);
+	isp1760_hcd_clear(hcd, HC_INT_IRQ_MASK_AND);
+	isp1760_hcd_clear(hcd, HC_ISO_IRQ_MASK_AND);
+
+	isp1760_hcd_set(hcd, HC_ATL_IRQ_MASK_OR);
+	isp1760_hcd_set(hcd, HC_INT_IRQ_MASK_OR);
+	isp1760_hcd_set(hcd, HC_ISO_IRQ_MASK_OR);
+
+	/* step 23 passed */
+
+	isp1760_hcd_set(hcd, HW_GLOBAL_INTR_EN);
+
+	isp1760_hcd_clear(hcd, CMD_LRESET);
+	isp1760_hcd_clear(hcd, CMD_RESET);
+
+	retval = isp1760_hcd_set_and_wait(hcd, CMD_RUN, 250 * 1000);
+	if (retval)
+		return retval;
+
+	/*
+	 * XXX
+	 * Spec says to write FLAG_CF as last config action, priv code grabs
+	 * the semaphore while doing so.
+	 */
+	down_write(&ehci_cf_port_reset_rwsem);
+
+	retval = isp1760_hcd_set_and_wait(hcd, FLAG_CF, 250 * 1000);
+	up_write(&ehci_cf_port_reset_rwsem);
+	if (retval)
+		return retval;
+
+	chipid_h = isp1760_hcd_read(hcd, HC_CHIP_ID_HIGH);
+	chipid_l = isp1760_hcd_read(hcd, HC_CHIP_ID_LOW);
+	chip_rev = isp1760_hcd_read(hcd, HC_CHIP_REV);
+	dev_info(priv->dev, "USB ISP %02x%02x HW rev. %d started\n",
+		 chipid_h, chipid_l, chip_rev);
+
+	/* PTD Register Init Part 2, Step 28 */
+
+	/* Setup registers controlling PTD checking */
+	ptd_atl_int = 0x80000000;
+	ptd_iso = 0x00000001;
+
+	isp1760_hcd_write(hcd, HC_ATL_PTD_LASTPTD, ptd_atl_int);
+	isp1760_hcd_write(hcd, HC_INT_PTD_LASTPTD, ptd_atl_int);
+	isp1760_hcd_write(hcd, HC_ISO_PTD_LASTPTD, ptd_iso);
+
+	isp1760_hcd_set(hcd, HC_ATL_PTD_SKIPMAP);
+	isp1760_hcd_set(hcd, HC_INT_PTD_SKIPMAP);
+	isp1760_hcd_set(hcd, HC_ISO_PTD_SKIPMAP);
+
+	isp1760_hcd_set(hcd, ATL_BUF_FILL);
+	isp1760_hcd_set(hcd, INT_BUF_FILL);
+
+	/* GRR this is run-once init(), being done every time the HC starts.
+	 * So long as they're part of class devices, we can't do it init()
+	 * since the class device isn't created that early.
+	 */
+	return 0;
+}
+
+static int qtd_fill(struct isp1760_qtd *qtd, void *databuffer, size_t len)
+{
+	qtd->data_buffer = databuffer;
+
+	qtd->length = len;
+
+	return qtd->length;
+}
+
+static void qtd_list_free(struct list_head *qtd_list)
+{
+	struct isp1760_qtd *qtd, *qtd_next;
+
+	list_for_each_entry_safe(qtd, qtd_next, qtd_list, qtd_list) {
+		list_del(&qtd->qtd_list);
+		qtd_free(qtd);
+	}
+}
+
+/*
+ * Packetize urb->transfer_buffer into list of packets of size wMaxPacketSize.
+ * Also calculate the PID type (SETUP/IN/OUT) for each packet.
+ */
+#define max_packet(wMaxPacketSize) ((wMaxPacketSize) & 0x07ff)
+static void packetize_urb(struct usb_hcd *hcd, struct urb *urb,
+			  struct list_head *head, gfp_t flags)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	const struct isp1760_memory_layout *mem = priv->memory_layout;
+	struct isp1760_qtd *qtd;
+	void *buf;
+	int len, maxpacketsize;
+	u8 packet_type;
+
+	/*
+	 * URBs map to sequences of QTDs:  one logical transaction
+	 */
+
+	if (!urb->transfer_buffer && urb->transfer_buffer_length) {
+		/* XXX This looks like usb storage / SCSI bug */
+		dev_err(priv->dev, "buf is null, dma is %08lx len is %d\n",
+			(unsigned long)urb->transfer_dma,
+			urb->transfer_buffer_length);
+		WARN_ON(1);
+	}
+
+	if (usb_pipein(urb->pipe))
+		packet_type = IN_PID;
+	else
+		packet_type = OUT_PID;
+
+	if (usb_pipecontrol(urb->pipe)) {
+		qtd = qtd_alloc(flags, urb, SETUP_PID);
+		if (!qtd)
+			goto cleanup;
+		qtd_fill(qtd, urb->setup_packet, sizeof(struct usb_ctrlrequest));
+		list_add_tail(&qtd->qtd_list, head);
+
+		/* for zero length DATA stages, STATUS is always IN */
+		if (urb->transfer_buffer_length == 0)
+			packet_type = IN_PID;
+	}
+
+	maxpacketsize = max_packet(usb_maxpacket(urb->dev, urb->pipe));
+
+	/*
+	 * buffer gets wrapped in one or more qtds;
+	 * last one may be "short" (including zero len)
+	 * and may serve as a control status ack
+	 */
+	buf = urb->transfer_buffer;
+	len = urb->transfer_buffer_length;
+
+	for (;;) {
+		int this_qtd_len;
+
+		qtd = qtd_alloc(flags, urb, packet_type);
+		if (!qtd)
+			goto cleanup;
+
+		if (len > mem->blocks_size[ISP176x_BLOCK_NUM - 1])
+			this_qtd_len = mem->blocks_size[ISP176x_BLOCK_NUM - 1];
+		else
+			this_qtd_len = len;
+
+		this_qtd_len = qtd_fill(qtd, buf, this_qtd_len);
+		list_add_tail(&qtd->qtd_list, head);
+
+		len -= this_qtd_len;
+		buf += this_qtd_len;
+
+		if (len <= 0)
+			break;
+	}
+
+	/*
+	 * control requests may need a terminating data "status" ack;
+	 * bulk ones may need a terminating short packet (zero length).
+	 */
+	if (urb->transfer_buffer_length != 0) {
+		int one_more = 0;
+
+		if (usb_pipecontrol(urb->pipe)) {
+			one_more = 1;
+			if (packet_type == IN_PID)
+				packet_type = OUT_PID;
+			else
+				packet_type = IN_PID;
+		} else if (usb_pipebulk(urb->pipe) && maxpacketsize &&
+			   (urb->transfer_flags & URB_ZERO_PACKET) &&
+			   !(urb->transfer_buffer_length % maxpacketsize)) {
+			one_more = 1;
+		}
+		if (one_more) {
+			qtd = qtd_alloc(flags, urb, packet_type);
+			if (!qtd)
+				goto cleanup;
+
+			/* never any data in such packets */
+			qtd_fill(qtd, NULL, 0);
+			list_add_tail(&qtd->qtd_list, head);
+		}
+	}
+
+	return;
+
+cleanup:
+	qtd_list_free(head);
+}
+
+static int isp1760_urb_enqueue(struct usb_hcd *hcd, struct urb *urb,
+			       gfp_t mem_flags)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	struct isp1760_qh *qh = NULL;
+	struct list_head *ep_queue;
+	LIST_HEAD(new_qtds);
+	int qh_in_queue;
+	int retval;
+	int epnum;
+
+	switch (usb_pipetype(urb->pipe)) {
+	case PIPE_CONTROL:
+		ep_queue = &priv->qh_list[QH_CONTROL];
+		break;
+	case PIPE_BULK:
+		ep_queue = &priv->qh_list[QH_BULK];
+		break;
+	case PIPE_INTERRUPT:
+		ep_queue = &priv->qh_list[QH_INTERRUPT];
+		break;
+	case PIPE_ISOCHRONOUS:
+		printf("isochronous USB packets not yet supported\n");
+		return -EPIPE;
+	default:
+		printf("unknown pipe type\n");
+		return -EPIPE;
+	}
+
+	if (usb_pipein(urb->pipe))
+		urb->actual_length = 0;
+
+	packetize_urb(hcd, urb, &new_qtds, mem_flags);
+	if (list_empty(&new_qtds))
+		return -ENOMEM;
+
+	retval = usb_hcd_link_urb_to_ep(hcd, urb);
+	if (retval) {
+		qtd_list_free(&new_qtds);
+		goto out;
+	}
+
+	epnum = usb_pipeendpoint(urb->pipe);
+
+	qh_in_queue = 0;
+	list_for_each_entry(qh, ep_queue, qh_list) {
+		if (qh->epnum == epnum) {
+			qh_in_queue = 1;
+			break;
+		}
+	}
+
+	if (!qh_in_queue) {
+		qh = qh_alloc(GFP_ATOMIC);
+		if (!qh) {
+			retval = -ENOMEM;
+			usb_hcd_unlink_urb_from_ep(hcd, urb);
+			qtd_list_free(&new_qtds);
+			goto out;
+		}
+
+		qh->epnum = epnum;
+		list_add_tail(&qh->qh_list, ep_queue);
+		urb->ep->hcpriv = qh;
+	}
+
+	list_splice_tail(&new_qtds, &qh->qtd_list);
+	schedule_ptds(hcd);
+
+out:
+	return retval;
+}
+
+static void kill_transfer(struct usb_hcd *hcd, struct urb *urb,
+			  struct isp1760_qh *qh)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	int skip_map;
+
+	WARN_ON(qh->slot == -1);
+
+	/*
+	 * We need to forcefully reclaim the slot since some transfers never
+	 * return, e.g. interrupt transfers and NAKed bulk transfers.
+	 */
+	if (usb_pipecontrol(urb->pipe) || usb_pipebulk(urb->pipe)) {
+		if (qh->slot != -1) {
+			skip_map = isp1760_hcd_read(hcd, HC_ATL_PTD_SKIPMAP);
+			skip_map |= (1 << qh->slot);
+			isp1760_hcd_write(hcd, HC_ATL_PTD_SKIPMAP, skip_map);
+			ndelay(100);
+		}
+		priv->atl_slots[qh->slot].qh = NULL;
+		priv->atl_slots[qh->slot].qtd = NULL;
+	} else {
+		if (qh->slot != -1) {
+			skip_map = isp1760_hcd_read(hcd, HC_INT_PTD_SKIPMAP);
+			skip_map |= (1 << qh->slot);
+			isp1760_hcd_write(hcd, HC_INT_PTD_SKIPMAP, skip_map);
+		}
+		priv->int_slots[qh->slot].qh = NULL;
+		priv->int_slots[qh->slot].qtd = NULL;
+	}
+
+	qh->slot = -1;
+}
+
+/*
+ * Retire the qtds beginning at 'qtd' and belonging all to the same urb, killing
+ * any active transfer belonging to the urb in the process.
+ */
+static void dequeue_urb_from_qtd(struct usb_hcd *hcd, struct isp1760_qh *qh,
+				 struct isp1760_qtd *qtd)
+{
+	struct urb *urb;
+	int urb_was_running;
+
+	urb = qtd->urb;
+	urb_was_running = 0;
+	list_for_each_entry_from(qtd, &qh->qtd_list, qtd_list) {
+		if (qtd->urb != urb)
+			break;
+
+		if (qtd->status >= QTD_XFER_STARTED)
+			urb_was_running = 1;
+		if (last_qtd_of_urb(qtd, qh) &&
+		    qtd->status >= QTD_XFER_COMPLETE)
+			urb_was_running = 0;
+
+		if (qtd->status == QTD_XFER_STARTED)
+			kill_transfer(hcd, urb, qh);
+		qtd->status = QTD_RETIRE;
+	}
+}
+
+int isp1760_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
+{
+	struct isp1760_qtd *qtd;
+	struct isp1760_qh *qh;
+	int retval = 0;
+
+	retval = usb_hcd_check_unlink_urb(hcd, urb, status);
+	if (retval)
+		goto out;
+
+	qh = urb->ep->hcpriv;
+	if (!qh) {
+		retval = -EINVAL;
+		goto out;
+	}
+
+	list_for_each_entry(qtd, &qh->qtd_list, qtd_list)
+		if (qtd->urb == urb) {
+			dequeue_urb_from_qtd(hcd, qh, qtd);
+			list_move(&qtd->qtd_list, &qh->qtd_list);
+			break;
+		}
+
+	urb->status = status;
+	schedule_ptds(hcd);
+
+out:
+	return retval;
+}
+
+static void isp1760_hub_descriptor(struct isp1760_hcd *priv,
+				   struct usb_hub_descriptor *desc)
+{
+	int ports;
+	u16 temp;
+
+	ports = isp1760_hcd_n_ports(priv->hcd);
+
+	desc->bDescriptorType = USB_DT_HUB;
+	/* priv 1.0, 2.3.9 says 20ms max */
+	desc->bPwrOn2PwrGood = 10;
+	desc->bHubContrCurrent = 0;
+
+	desc->bNbrPorts = ports;
+	temp = 1 + (ports / 8);
+	desc->bLength = 7 + 2 * temp;
+
+	/* ports removable, and usb 1.0 legacy PortPwrCtrlMask */
+	memset(&desc->u.hs.DeviceRemovable[0], 0, temp);
+	memset(&desc->u.hs.DeviceRemovable[temp], 0xff, temp);
+
+	/* per-port overcurrent reporting */
+	temp = HUB_CHAR_INDV_PORT_OCPM;
+	if (isp1760_hcd_ppc_is_set(priv->hcd))
+		/* per-port power control */
+		temp |= HUB_CHAR_INDV_PORT_LPSM;
+	else
+		/* no power switching */
+		temp |= HUB_CHAR_NO_LPSM;
+	desc->wHubCharacteristics = cpu_to_le16(temp);
+}
+
+#define	PORT_WAKE_BITS	(PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E)
+
+static void check_reset_complete(struct usb_hcd *hcd, int index)
+{
+	if (!(isp1760_hcd_is_set(hcd, PORT_CONNECT)))
+		return;
+
+	/* if reset finished and it's still not enabled -- handoff */
+	if (!isp1760_hcd_is_set(hcd, PORT_PE)) {
+		printf("port %d full speed --> companion\n", index + 1);
+
+		isp1760_hcd_set(hcd, PORT_OWNER);
+
+		isp1760_hcd_clear(hcd, PORT_CSC);
+	} else {
+		printf("port %d high speed\n", index + 1);
+	}
+}
+
+static int isp1760_hub_control(struct usb_hcd *hcd, struct usb_device *dev,
+			       unsigned long pipe, void *buffer, int length,
+			       struct devrequest *setup)
+{
+	struct isp1760_hcd *priv = hcd_to_priv(hcd);
+	u16 typeReq, wValue, wIndex;
+	char *buf = buffer;
+	void *src = NULL;
+	int src_len = 0;
+	int retval = 0;
+	u32 status;
+	int ports;
+
+	if (!setup)
+		return -EINVAL;
+
+	ports = isp1760_hcd_n_ports(hcd);
+
+	typeReq = setup->request | (setup->requesttype << 8);
+	wValue = le16_to_cpu(setup->value);
+	wIndex = le16_to_cpu(setup->index);
+
+	/*
+	 * FIXME:  support SetPortFeatures USB_PORT_FEAT_INDICATOR.
+	 * HCS_INDICATOR may say we can change LEDs to off/amber/green.
+	 * (track current state ourselves) ... blink for diagnostics,
+	 * power, "this is the one", etc.  EHCI spec supports this.
+	 */
+
+	switch (typeReq) {
+	case DeviceOutRequest | USB_REQ_SET_ADDRESS:
+		break;
+	case DeviceOutRequest | USB_REQ_SET_CONFIGURATION:
+		/* Nothing to do */
+		break;
+	case DeviceRequest | USB_REQ_GET_DESCRIPTOR:
+		switch (wValue & 0xff00) {
+		case USB_DT_DEVICE << 8:
+			src = &rh_descriptor.device;
+			src_len = 0x12;
+			break;
+		case USB_DT_CONFIG << 8:
+			src = &rh_descriptor.config;
+			src_len = 0x09;
+			break;
+		case USB_DT_STRING << 8:
+			switch (wValue & 0xff) {
+			case 0:	/* Language */
+				src = ISP1760_LANGUAGE_DESC;
+				src_len = 4;
+				break;
+			case 1:	/* Vendor String  */
+				src = ISP1760_VENDOR_DESC;
+				src_len = 14;
+				break;
+			case 2:	/* Product Name */
+				src = ISP1760_PRODUCT_NAME_DESC;
+				src_len = 42;
+				break;
+			default:
+				goto error;
+			}
+			break;
+		}
+		break;
+	case ClearHubFeature:
+		switch (wValue) {
+		case C_HUB_LOCAL_POWER:
+		case C_HUB_OVER_CURRENT:
+			/* no hub-wide feature/status flags */
+			break;
+		default:
+			goto error;
+		}
+		break;
+	case ClearPortFeature:
+		if (!wIndex || wIndex > ports)
+			goto error;
+		wIndex--;
+
+		/*
+		 * Even if OWNER is set, so the port is owned by the
+		 * companion controller, hub_wq needs to be able to clear
+		 * the port-change status bits (especially
+		 * USB_PORT_STAT_C_CONNECTION).
+		 */
+
+		switch (wValue) {
+		case USB_PORT_FEAT_ENABLE:
+			isp1760_hcd_clear(hcd, PORT_PE);
+			break;
+		case USB_PORT_FEAT_C_ENABLE:
+			/* XXX error? */
+			break;
+		case USB_PORT_FEAT_SUSPEND:
+			if (isp1760_hcd_is_set(hcd, PORT_RESET))
+				goto error;
+
+			if (isp1760_hcd_is_set(hcd, PORT_SUSPEND)) {
+				if (!isp1760_hcd_is_set(hcd, PORT_PE))
+					goto error;
+				/* resume signaling for 20 msec */
+				isp1760_hcd_clear(hcd, PORT_CSC);
+				isp1760_hcd_set(hcd, PORT_RESUME);
+
+				priv->reset_done = get_timer(0) + 40;
+			}
+			break;
+		case USB_PORT_FEAT_C_SUSPEND:
+			/* we auto-clear this feature */
+			break;
+		case USB_PORT_FEAT_POWER:
+			if (isp1760_hcd_ppc_is_set(hcd))
+				isp1760_hcd_clear(hcd, PORT_POWER);
+			break;
+		case USB_PORT_FEAT_C_CONNECTION:
+			isp1760_hcd_set(hcd, PORT_CSC);
+			break;
+		case USB_PORT_FEAT_C_OVER_CURRENT:
+			/* XXX error ?*/
+			break;
+		case USB_PORT_FEAT_C_RESET:
+			/* GetPortStatus clears reset */
+			break;
+		default:
+			goto error;
+		}
+		isp1760_hcd_read(hcd, CMD_RUN);
+		break;
+	case GetHubDescriptor:
+		isp1760_hub_descriptor(priv, (struct usb_hub_descriptor *)buf);
+		break;
+	case GetHubStatus:
+		/* no hub-wide feature/status flags */
+		memset(buf, 0, 4);
+		break;
+	case GetPortStatus:
+		if (!wIndex || wIndex > ports)
+			goto error;
+		wIndex--;
+		status = 0;
+
+		/* wPortChange bits */
+		if (isp1760_hcd_is_set(hcd, PORT_CSC))
+			status |= USB_PORT_STAT_C_CONNECTION << 16;
+
+		/* whoever resumes must GetPortStatus to complete it!! */
+		if (isp1760_hcd_is_set(hcd, PORT_RESUME)) {
+			status |= USB_PORT_STAT_C_SUSPEND << 16;
+
+			if (!priv->reset_done) {
+				priv->reset_done = get_timer(0) + 20;
+			} else if (get_timer(0) > priv->reset_done) {
+				/* stop resume signaling */
+				isp1760_hcd_clear(hcd, PORT_CSC);
+
+				retval = isp1760_hcd_clear_and_wait(hcd,
+								    PORT_RESUME,
+								    2000);
+				if (retval != 0) {
+					printf("port %d resume error %d\n",
+					       wIndex + 1, retval);
+					goto error;
+				}
+			}
+		}
+
+		/* whoever resets must GetPortStatus to complete it!! */
+		if (isp1760_hcd_is_set(hcd, PORT_RESET) &&
+		    get_timer(0) > priv->reset_done) {
+			status |= USB_PORT_STAT_C_RESET << 16;
+			priv->reset_done = 0;
+
+			/* force reset to complete */
+			/* REVISIT:  some hardware needs 550+ usec to clear
+			 * this bit; seems too long to spin routinely...
+			 */
+			retval = isp1760_hcd_clear_and_wait(hcd, PORT_RESET,
+							    750);
+			if (retval != 0) {
+				printf("port %d reset error %d\n", wIndex + 1,
+				       retval);
+				goto error;
+			}
+
+			/* see what we found out */
+			check_reset_complete(hcd, wIndex);
+		}
+		/*
+		 * Even if OWNER is set, there's no harm letting hub_wq
+		 * see the wPortStatus values (they should all be 0 except
+		 * for PORT_POWER anyway).
+		 */
+
+		if (isp1760_hcd_is_set(hcd, PORT_OWNER))
+			printf("PORT_OWNER is set\n");
+
+		if (isp1760_hcd_is_set(hcd, PORT_CONNECT)) {
+			status |= USB_PORT_STAT_CONNECTION;
+
+			/* status may be from integrated TT */
+			status |= USB_PORT_STAT_HIGH_SPEED;
+		}
+		if (isp1760_hcd_is_set(hcd, PORT_PE))
+			status |= USB_PORT_STAT_ENABLE;
+		if (isp1760_hcd_is_set(hcd, PORT_SUSPEND) &&
+		    isp1760_hcd_is_set(hcd, PORT_RESUME))
+			status |= USB_PORT_STAT_SUSPEND;
+		if (isp1760_hcd_is_set(hcd, PORT_RESET))
+			status |= USB_PORT_STAT_RESET;
+		if (isp1760_hcd_is_set(hcd, PORT_POWER))
+			status |= USB_PORT_STAT_POWER;
+
+		put_unaligned(cpu_to_le32(status), (__le32 *)buf);
+		break;
+	case SetHubFeature:
+		switch (wValue) {
+		case C_HUB_LOCAL_POWER:
+		case C_HUB_OVER_CURRENT:
+			/* no hub-wide feature/status flags */
+			break;
+		default:
+			goto error;
+		}
+		break;
+	case SetPortFeature:
+		wIndex &= 0xff;
+		if (!wIndex || wIndex > ports)
+			goto error;
+		wIndex--;
+
+		if (isp1760_hcd_is_set(hcd, PORT_OWNER))
+			break;
+
+		switch (wValue) {
+		case USB_PORT_FEAT_ENABLE:
+			isp1760_hcd_set(hcd, PORT_PE);
+			break;
+
+		case USB_PORT_FEAT_SUSPEND:
+			if (!isp1760_hcd_is_set(hcd, PORT_PE) ||
+			    isp1760_hcd_is_set(hcd, PORT_RESET))
+				goto error;
+
+			isp1760_hcd_set(hcd, PORT_SUSPEND);
+			break;
+		case USB_PORT_FEAT_POWER:
+			if (isp1760_hcd_ppc_is_set(hcd))
+				isp1760_hcd_set(hcd, PORT_POWER);
+			break;
+		case USB_PORT_FEAT_RESET:
+			if (isp1760_hcd_is_set(hcd, PORT_RESUME))
+				goto error;
+			/* line status bits may report this as low speed,
+			 * which can be fine if this root hub has a
+			 * transaction translator built in.
+			 */
+			if ((isp1760_hcd_is_set(hcd, PORT_CONNECT) &&
+			     !isp1760_hcd_is_set(hcd, PORT_PE)) &&
+			    (isp1760_hcd_read(hcd, PORT_LSTATUS) == 1)) {
+				isp1760_hcd_set(hcd, PORT_OWNER);
+			} else {
+				isp1760_hcd_set(hcd, PORT_RESET);
+				isp1760_hcd_clear(hcd, PORT_PE);
+
+				priv->reset_done = get_timer(0) + 50;
+			}
+			break;
+		default:
+			goto error;
+		}
+		break;
+
+	default:
+		printf("root: unknown request: 0x%0x\n", typeReq);
+		goto error;
+	}
+
+	if (src_len) {
+		length = min(src_len, length);
+
+		if (src && length > 0)
+			memcpy(buffer, src, length);
+		else
+			printf("zero copy USB descriptor\n");
+	}
+
+	dev->act_len = length;
+	dev->status = 0;
+
+	return 0;
+
+error:
+	/* "stall" on error */
+	dev->act_len = 0;
+	dev->status = USB_ST_STALLED;
+	return -EPIPE;
+}
+
+int __init isp1760_init_kmem_once(void)
+{
+	urb_listitem_cachep = kmem_cache_create("isp1760_urb_listitem",
+						sizeof(struct urb_listitem), 0,
+						SLAB_TEMPORARY |
+						SLAB_MEM_SPREAD, NULL);
+
+	if (!urb_listitem_cachep)
+		return -ENOMEM;
+
+	qtd_cachep = kmem_cache_create("isp1760_qtd",
+				       sizeof(struct isp1760_qtd), 0,
+				       SLAB_TEMPORARY | SLAB_MEM_SPREAD, NULL);
+
+	if (!qtd_cachep)
+		goto destroy_urb_listitem;
+
+	qh_cachep = kmem_cache_create("isp1760_qh", sizeof(struct isp1760_qh),
+				      0, SLAB_TEMPORARY | SLAB_MEM_SPREAD,
+				      NULL);
+
+	if (!qh_cachep)
+		goto destroy_qtd;
+
+	return 0;
+
+destroy_qtd:
+	kmem_cache_destroy(qtd_cachep);
+
+destroy_urb_listitem:
+	kmem_cache_destroy(urb_listitem_cachep);
+
+	return -ENOMEM;
+}
+
+void isp1760_deinit_kmem_cache(void)
+{
+	kmem_cache_destroy(qtd_cachep);
+	kmem_cache_destroy(qh_cachep);
+	kmem_cache_destroy(urb_listitem_cachep);
+}
+
+int isp1760_hcd_lowlevel_init(struct isp1760_hcd *priv)
+{
+	int ret;
+
+	ret = isp1760_hc_setup(priv->hcd);
+	if (ret < 0)
+		return ret;
+
+	ret = isp1760_run(priv->hcd);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static const struct usb_urb_ops isp1760_urb_ops = {
+	.urb_enqueue = isp1760_urb_enqueue,
+	.urb_dequeue = isp1760_urb_dequeue,
+	.hub_control = isp1760_hub_control,
+	.isr = isp1760_irq,
+};
+
+int isp1760_hcd_register(struct isp1760_hcd *priv, struct resource *mem,
+			 int irq, unsigned long irqflags,
+			 struct udevice *dev)
+{
+	const struct isp1760_memory_layout *mem_layout = priv->memory_layout;
+	struct isp1760_host_data *host = dev_get_priv(dev);
+	struct usb_hcd *hcd = &host->hcd;
+	int ret;
+
+	priv->hcd = hcd;
+
+	hcd->hcd_priv = priv;
+
+	priv->hcd = hcd;
+
+	hcd->urb_ops = &isp1760_urb_ops;
+
+	priv->atl_slots = kcalloc(mem_layout->slot_num,
+				  sizeof(struct isp1760_slotinfo), GFP_KERNEL);
+	if (!priv->atl_slots)
+		return -ENOMEM;
+
+	priv->int_slots = kcalloc(mem_layout->slot_num,
+				  sizeof(struct isp1760_slotinfo), GFP_KERNEL);
+	if (!priv->int_slots) {
+		ret = -ENOMEM;
+		goto free_atl_slots;
+	}
+
+	host->host_speed = USB_SPEED_HIGH;
+
+	init_memory(priv);
+
+	return 0;
+
+free_atl_slots:
+	kfree(priv->atl_slots);
+
+	return ret;
+}
+
+void isp1760_hcd_unregister(struct isp1760_hcd *priv)
+{
+	struct isp1760_qh *qh, *qh_next;
+	int i;
+
+	for (i = 0; i < QH_END; i++)
+		list_for_each_entry_safe(qh, qh_next, &priv->qh_list[i],
+					 qh_list) {
+			qtd_list_free(&qh->qtd_list);
+			list_del(&qh->qh_list);
+			qh_free(qh);
+		}
+
+	kfree(priv->atl_slots);
+	kfree(priv->int_slots);
+}
diff --git a/drivers/usb/isp1760/isp1760-hcd.h b/drivers/usb/isp1760/isp1760-hcd.h
new file mode 100644
index 000000000000..c47b73906ef9
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-hcd.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ISP1760_HCD_H_
+#define _ISP1760_HCD_H_
+
+#include <regmap.h>
+
+#include "isp1760-regs.h"
+
+struct isp1760_qh;
+struct isp1760_qtd;
+struct resource;
+struct usb_hcd;
+
+struct isp1760_slotinfo {
+	struct isp1760_qh *qh;
+	struct isp1760_qtd *qtd;
+	unsigned long timestamp;
+};
+
+/* chip memory management */
+#define ISP176x_BLOCK_MAX (32 + 20 + 4)
+#define ISP176x_BLOCK_NUM 3
+
+struct isp1760_memory_layout {
+	unsigned int blocks[ISP176x_BLOCK_NUM];
+	unsigned int blocks_size[ISP176x_BLOCK_NUM];
+
+	unsigned int slot_num;
+	unsigned int payload_blocks;
+	unsigned int payload_area_size;
+};
+
+struct isp1760_memory_chunk {
+	unsigned int start;
+	unsigned int size;
+	unsigned int free;
+};
+
+enum isp1760_queue_head_types {
+	QH_CONTROL,
+	QH_BULK,
+	QH_INTERRUPT,
+	QH_END
+};
+
+struct isp1760_hcd {
+	struct usb_hcd		*hcd;
+	struct udevice		*dev;
+
+	void __iomem		*base;
+
+	struct regmap		*regs;
+	struct regmap_field	*fields[HC_FIELD_MAX];
+
+	bool			is_isp1763;
+	const struct isp1760_memory_layout	*memory_layout;
+
+	struct isp1760_slotinfo	*atl_slots;
+	int			atl_done_map;
+	struct isp1760_slotinfo	*int_slots;
+	int			int_done_map;
+	struct isp1760_memory_chunk memory_pool[ISP176x_BLOCK_MAX];
+	struct list_head	qh_list[QH_END];
+
+	/* periodic schedule support */
+#define	DEFAULT_I_TDPS		1024
+	unsigned int		periodic_size;
+	unsigned int		i_thresh;
+	unsigned long		reset_done;
+	unsigned long		next_statechange;
+};
+
+int isp1760_hcd_register(struct isp1760_hcd *priv, struct resource *mem,
+			 int irq, unsigned long irqflags, struct udevice *dev);
+void isp1760_hcd_unregister(struct isp1760_hcd *priv);
+int isp1760_hcd_lowlevel_init(struct isp1760_hcd *priv);
+
+int isp1760_init_kmem_once(void);
+void isp1760_deinit_kmem_cache(void);
+
+#endif /* _ISP1760_HCD_H_ */
diff --git a/drivers/usb/isp1760/isp1760-if.c b/drivers/usb/isp1760/isp1760-if.c
new file mode 100644
index 000000000000..c96ab459f93e
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-if.c
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021 Linaro, Rui Miguel Silva <rui.silva@linaro.org>
+ *
+ * based on original code from:
+ * (c) 2007 Sebastian Siewior <bigeasy@linutronix.de>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <dm/device_compat.h>
+#include <dm/devres.h>
+#include <dm/lists.h>
+#include <linux/bug.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/usb/otg.h>
+#include <log.h>
+#include <usb.h>
+
+#include "isp1760-core.h"
+#include "isp1760-regs.h"
+#include "isp1760-uboot.h"
+
+static int isp1760_of_to_plat(struct udevice *dev)
+{
+	struct isp1760_device *isp = dev_get_plat(dev);
+	unsigned int devflags = 0;
+	u32 bus_width = 0;
+	ofnode dp;
+
+	if (!dev_has_ofnode(dev)) {
+		/* select isp1763 as the default device */
+		devflags = ISP1760_FLAG_ISP1763 | ISP1760_FLAG_BUS_WIDTH_16;
+		pr_err("isp1760: no platform data\n");
+		goto isp_setup;
+	}
+
+	dp = dev_ofnode(dev);
+
+	if (ofnode_device_is_compatible(dp, "nxp,usb-isp1761"))
+		devflags |= ISP1760_FLAG_ISP1761;
+
+	if (ofnode_device_is_compatible(dp, "nxp,usb-isp1763"))
+		devflags |= ISP1760_FLAG_ISP1763;
+
+	/*
+	 * Some systems wire up only 8 of 16 data lines or
+	 * 16 of the 32 data lines
+	 */
+	bus_width = ofnode_read_u32_default(dp, "bus-width", 16);
+	if (bus_width == 16)
+		devflags |= ISP1760_FLAG_BUS_WIDTH_16;
+	else if (bus_width == 8)
+		devflags |= ISP1760_FLAG_BUS_WIDTH_8;
+
+	if (usb_get_dr_mode(dev_ofnode(dev)) == USB_DR_MODE_PERIPHERAL)
+		devflags |= ISP1760_FLAG_PERIPHERAL_EN;
+
+	if (ofnode_read_bool(dp, "analog-oc"))
+		devflags |= ISP1760_FLAG_ANALOG_OC;
+
+	if (ofnode_read_bool(dp, "dack-polarity"))
+		devflags |= ISP1760_FLAG_DACK_POL_HIGH;
+
+	if (ofnode_read_bool(dp, "dreq-polarity"))
+		devflags |= ISP1760_FLAG_DREQ_POL_HIGH;
+
+isp_setup:
+	isp->devflags = devflags;
+	isp->dev = dev;
+
+	return 0;
+}
+
+static int isp1760_plat_probe(struct udevice *dev)
+{
+	struct isp1760_device *isp = dev_get_plat(dev);
+	struct resource mem_res;
+	struct resource irq_res;
+	int ret;
+
+	dev_read_resource(dev, 0, &mem_res);
+	dev_read_resource(dev, 1, &irq_res);
+
+	isp1760_init_kmem_once();
+
+	ret = isp1760_register(isp, &mem_res, irq_res.start, irq_res.flags);
+	if (ret < 0) {
+		isp1760_deinit_kmem_cache();
+		return ret;
+	}
+
+	return 0;
+}
+
+static int isp1760_plat_remove(struct udevice *dev)
+{
+	struct isp1760_device *isp = dev_get_plat(dev);
+
+	isp1760_deinit_kmem_cache();
+	isp1760_unregister(isp);
+
+	return 0;
+}
+
+static const struct udevice_id isp1760_ids[] = {
+	{ .compatible = "nxp,usb-isp1760", },
+	{ .compatible = "nxp,usb-isp1761", },
+	{ .compatible = "nxp,usb-isp1763", },
+	{ },
+};
+
+U_BOOT_DRIVER(isp1760) = {
+	.name		= "isp1760",
+	.id		= UCLASS_USB,
+	.of_match	= isp1760_ids,
+	.of_to_plat	= isp1760_of_to_plat,
+	.ops		= &isp1760_usb_ops,
+	.probe		= isp1760_plat_probe,
+	.remove		= isp1760_plat_remove,
+	.plat_auto	= sizeof(struct isp1760_device),
+	.priv_auto	= sizeof(struct isp1760_host_data),
+};
diff --git a/drivers/usb/isp1760/isp1760-regs.h b/drivers/usb/isp1760/isp1760-regs.h
new file mode 100644
index 000000000000..94ea60c20b2a
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-regs.h
@@ -0,0 +1,292 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Driver for the NXP ISP1760 chip
+ *
+ * Copyright 2021 Linaro, Rui Miguel Silva
+ * Copyright 2014 Laurent Pinchart
+ * Copyright 2007 Sebastian Siewior
+ *
+ * Contacts:
+ *     Sebastian Siewior <bigeasy@linutronix.de>
+ *     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+ *     Rui Miguel Silva <rui.silva@linaro.org>
+ */
+
+#ifndef _ISP176x_REGS_H_
+#define _ISP176x_REGS_H_
+
+/* -----------------------------------------------------------------------------
+ * Host Controller
+ */
+
+/* ISP1760/31 */
+/* EHCI capability registers */
+#define ISP176x_HC_VERSION		0x002
+#define ISP176x_HC_HCSPARAMS		0x004
+#define ISP176x_HC_HCCPARAMS		0x008
+
+/* EHCI operational registers */
+#define ISP176x_HC_USBCMD		0x020
+#define ISP176x_HC_USBSTS		0x024
+#define ISP176x_HC_FRINDEX		0x02c
+
+#define ISP176x_HC_CONFIGFLAG		0x060
+#define ISP176x_HC_PORTSC1		0x064
+
+#define ISP176x_HC_ISO_PTD_DONEMAP	0x130
+#define ISP176x_HC_ISO_PTD_SKIPMAP	0x134
+#define ISP176x_HC_ISO_PTD_LASTPTD	0x138
+#define ISP176x_HC_INT_PTD_DONEMAP	0x140
+#define ISP176x_HC_INT_PTD_SKIPMAP	0x144
+#define ISP176x_HC_INT_PTD_LASTPTD	0x148
+#define ISP176x_HC_ATL_PTD_DONEMAP	0x150
+#define ISP176x_HC_ATL_PTD_SKIPMAP	0x154
+#define ISP176x_HC_ATL_PTD_LASTPTD	0x158
+
+/* Configuration Register */
+#define ISP176x_HC_HW_MODE_CTRL		0x300
+#define ISP176x_HC_CHIP_ID		0x304
+#define ISP176x_HC_SCRATCH		0x308
+#define ISP176x_HC_RESET		0x30c
+#define ISP176x_HC_BUFFER_STATUS	0x334
+#define ISP176x_HC_MEMORY		0x33c
+
+/* Interrupt Register */
+#define ISP176x_HC_INTERRUPT		0x310
+#define ISP176x_HC_INTERRUPT_ENABLE	0x314
+#define ISP176x_HC_ISO_IRQ_MASK_OR	0x318
+#define ISP176x_HC_INT_IRQ_MASK_OR	0x31c
+#define ISP176x_HC_ATL_IRQ_MASK_OR	0x320
+#define ISP176x_HC_ISO_IRQ_MASK_AND	0x324
+#define ISP176x_HC_INT_IRQ_MASK_AND	0x328
+#define ISP176x_HC_ATL_IRQ_MASK_AND	0x32c
+
+#define ISP176x_HC_OTG_CTRL_SET		0x374
+#define ISP176x_HC_OTG_CTRL_CLEAR	0x376
+
+enum isp176x_host_controller_fields {
+	/* HC_PORTSC1 */
+	PORT_OWNER, PORT_POWER, PORT_LSTATUS, PORT_RESET, PORT_SUSPEND,
+	PORT_RESUME, PORT_PE, PORT_CSC, PORT_CONNECT,
+	/* HC_HCSPARAMS */
+	HCS_PPC, HCS_N_PORTS,
+	/* HC_HCCPARAMS */
+	HCC_ISOC_CACHE, HCC_ISOC_THRES,
+	/* HC_USBCMD */
+	CMD_LRESET, CMD_RESET, CMD_RUN,
+	/* HC_USBSTS */
+	STS_PCD,
+	/* HC_FRINDEX */
+	HC_FRINDEX,
+	/* HC_CONFIGFLAG */
+	FLAG_CF,
+	/* ISO/INT/ATL PTD */
+	HC_ISO_PTD_DONEMAP, HC_ISO_PTD_SKIPMAP, HC_ISO_PTD_LASTPTD,
+	HC_INT_PTD_DONEMAP, HC_INT_PTD_SKIPMAP, HC_INT_PTD_LASTPTD,
+	HC_ATL_PTD_DONEMAP, HC_ATL_PTD_SKIPMAP, HC_ATL_PTD_LASTPTD,
+	/* HC_HW_MODE_CTRL */
+	ALL_ATX_RESET, HW_ANA_DIGI_OC, HW_DEV_DMA, HW_COMN_IRQ, HW_COMN_DMA,
+	HW_DATA_BUS_WIDTH, HW_DACK_POL_HIGH, HW_DREQ_POL_HIGH, HW_INTR_HIGH_ACT,
+	HW_INTF_LOCK, HW_INTR_EDGE_TRIG, HW_GLOBAL_INTR_EN,
+	/* HC_CHIP_ID */
+	HC_CHIP_ID_HIGH, HC_CHIP_ID_LOW, HC_CHIP_REV,
+	/* HC_SCRATCH */
+	HC_SCRATCH,
+	/* HC_RESET */
+	SW_RESET_RESET_ATX, SW_RESET_RESET_HC, SW_RESET_RESET_ALL,
+	/* HC_BUFFER_STATUS */
+	ISO_BUF_FILL, INT_BUF_FILL, ATL_BUF_FILL,
+	/* HC_MEMORY */
+	MEM_BANK_SEL, MEM_START_ADDR,
+	/* HC_DATA */
+	HC_DATA,
+	/* HC_INTERRUPT */
+	HC_INTERRUPT,
+	/* HC_INTERRUPT_ENABLE */
+	HC_INT_IRQ_ENABLE, HC_ATL_IRQ_ENABLE,
+	/* INTERRUPT MASKS */
+	HC_ISO_IRQ_MASK_OR, HC_INT_IRQ_MASK_OR, HC_ATL_IRQ_MASK_OR,
+	HC_ISO_IRQ_MASK_AND, HC_INT_IRQ_MASK_AND, HC_ATL_IRQ_MASK_AND,
+	/* HW_OTG_CTRL_SET */
+	HW_OTG_DISABLE, HW_SW_SEL_HC_DC, HW_VBUS_DRV, HW_SEL_CP_EXT,
+	HW_DM_PULLDOWN, HW_DP_PULLDOWN, HW_DP_PULLUP, HW_HC_2_DIS,
+	/* HW_OTG_CTRL_CLR */
+	HW_OTG_DISABLE_CLEAR, HW_SW_SEL_HC_DC_CLEAR, HW_VBUS_DRV_CLEAR,
+	HW_SEL_CP_EXT_CLEAR, HW_DM_PULLDOWN_CLEAR, HW_DP_PULLDOWN_CLEAR,
+	HW_DP_PULLUP_CLEAR, HW_HC_2_DIS_CLEAR,
+	/* Last element */
+	HC_FIELD_MAX,
+};
+
+/* ISP1763 */
+/* EHCI operational registers */
+#define ISP1763_HC_USBCMD		0x8c
+#define ISP1763_HC_USBSTS		0x90
+#define ISP1763_HC_FRINDEX		0x98
+
+#define ISP1763_HC_CONFIGFLAG		0x9c
+#define ISP1763_HC_PORTSC1		0xa0
+
+#define ISP1763_HC_ISO_PTD_DONEMAP	0xa4
+#define ISP1763_HC_ISO_PTD_SKIPMAP	0xa6
+#define ISP1763_HC_ISO_PTD_LASTPTD	0xa8
+#define ISP1763_HC_INT_PTD_DONEMAP	0xaa
+#define ISP1763_HC_INT_PTD_SKIPMAP	0xac
+#define ISP1763_HC_INT_PTD_LASTPTD	0xae
+#define ISP1763_HC_ATL_PTD_DONEMAP	0xb0
+#define ISP1763_HC_ATL_PTD_SKIPMAP	0xb2
+#define ISP1763_HC_ATL_PTD_LASTPTD	0xb4
+
+/* Configuration Register */
+#define ISP1763_HC_HW_MODE_CTRL		0xb6
+#define ISP1763_HC_CHIP_REV		0x70
+#define ISP1763_HC_CHIP_ID		0x72
+#define ISP1763_HC_SCRATCH		0x78
+#define ISP1763_HC_RESET		0xb8
+#define ISP1763_HC_BUFFER_STATUS	0xba
+#define ISP1763_HC_MEMORY		0xc4
+#define ISP1763_HC_DATA			0xc6
+
+/* Interrupt Register */
+#define ISP1763_HC_INTERRUPT		0xd4
+#define ISP1763_HC_INTERRUPT_ENABLE	0xd6
+#define ISP1763_HC_ISO_IRQ_MASK_OR	0xd8
+#define ISP1763_HC_INT_IRQ_MASK_OR	0xda
+#define ISP1763_HC_ATL_IRQ_MASK_OR	0xdc
+#define ISP1763_HC_ISO_IRQ_MASK_AND	0xde
+#define ISP1763_HC_INT_IRQ_MASK_AND	0xe0
+#define ISP1763_HC_ATL_IRQ_MASK_AND	0xe2
+
+#define ISP1763_HC_OTG_CTRL_SET		0xe4
+#define ISP1763_HC_OTG_CTRL_CLEAR	0xe6
+
+/* -----------------------------------------------------------------------------
+ * Peripheral Controller
+ */
+
+#define DC_IEPTX(n)			(1 << (11 + 2 * (n)))
+#define DC_IEPRX(n)			(1 << (10 + 2 * (n)))
+#define DC_IEPRXTX(n)			(3 << (10 + 2 * (n)))
+
+#define ISP176x_DC_CDBGMOD_ACK		BIT(6)
+#define ISP176x_DC_DDBGMODIN_ACK	BIT(4)
+#define ISP176x_DC_DDBGMODOUT_ACK	BIT(2)
+
+#define ISP176x_DC_IEP0SETUP		BIT(8)
+#define ISP176x_DC_IEVBUS		BIT(7)
+#define ISP176x_DC_IEHS_STA		BIT(5)
+#define ISP176x_DC_IERESM		BIT(4)
+#define ISP176x_DC_IESUSP		BIT(3)
+#define ISP176x_DC_IEBRST		BIT(0)
+
+#define ISP176x_DC_ENDPTYP_ISOC		0x01
+#define ISP176x_DC_ENDPTYP_BULK		0x02
+#define ISP176x_DC_ENDPTYP_INTERRUPT	0x03
+
+/* Initialization Registers */
+#define ISP176x_DC_ADDRESS		0x0200
+#define ISP176x_DC_MODE			0x020c
+#define ISP176x_DC_INTCONF		0x0210
+#define ISP176x_DC_DEBUG		0x0212
+#define ISP176x_DC_INTENABLE		0x0214
+
+/* Data Flow Registers */
+#define ISP176x_DC_EPMAXPKTSZ		0x0204
+#define ISP176x_DC_EPTYPE		0x0208
+
+#define ISP176x_DC_BUFLEN		0x021c
+#define ISP176x_DC_BUFSTAT		0x021e
+#define ISP176x_DC_DATAPORT		0x0220
+
+#define ISP176x_DC_CTRLFUNC		0x0228
+#define ISP176x_DC_EPINDEX		0x022c
+
+/* DMA Registers */
+#define ISP176x_DC_DMACMD		0x0230
+#define ISP176x_DC_DMATXCOUNT		0x0234
+#define ISP176x_DC_DMACONF		0x0238
+#define ISP176x_DC_DMAHW		0x023c
+#define ISP176x_DC_DMAINTREASON		0x0250
+#define ISP176x_DC_DMAINTEN		0x0254
+#define ISP176x_DC_DMAEP		0x0258
+#define ISP176x_DC_DMABURSTCOUNT	0x0264
+
+/* General Registers */
+#define ISP176x_DC_INTERRUPT		0x0218
+#define ISP176x_DC_CHIPID		0x0270
+#define ISP176x_DC_FRAMENUM		0x0274
+#define ISP176x_DC_SCRATCH		0x0278
+#define ISP176x_DC_UNLOCKDEV		0x027c
+#define ISP176x_DC_INTPULSEWIDTH	0x0280
+#define ISP176x_DC_TESTMODE		0x0284
+
+enum isp176x_device_controller_fields {
+	/* DC_ADDRESS */
+	DC_DEVEN, DC_DEVADDR,
+	/* DC_MODE */
+	DC_VBUSSTAT, DC_SFRESET, DC_GLINTENA,
+	/* DC_INTCONF */
+	DC_CDBGMOD_ACK, DC_DDBGMODIN_ACK, DC_DDBGMODOUT_ACK, DC_INTPOL,
+	/* DC_INTENABLE */
+	DC_IEPRXTX_7, DC_IEPRXTX_6, DC_IEPRXTX_5, DC_IEPRXTX_4, DC_IEPRXTX_3,
+	DC_IEPRXTX_2, DC_IEPRXTX_1, DC_IEPRXTX_0,
+	DC_IEP0SETUP, DC_IEVBUS, DC_IEHS_STA, DC_IERESM, DC_IESUSP, DC_IEBRST,
+	/* DC_EPINDEX */
+	DC_EP0SETUP, DC_ENDPIDX, DC_EPDIR,
+	/* DC_CTRLFUNC */
+	DC_CLBUF, DC_VENDP, DC_DSEN, DC_STATUS, DC_STALL,
+	/* DC_BUFLEN */
+	DC_BUFLEN,
+	/* DC_EPMAXPKTSZ */
+	DC_FFOSZ,
+	/* DC_EPTYPE */
+	DC_EPENABLE, DC_ENDPTYP,
+	/* DC_FRAMENUM */
+	DC_FRAMENUM, DC_UFRAMENUM,
+	/* DC_CHIP_ID */
+	DC_CHIP_ID_HIGH, DC_CHIP_ID_LOW,
+	/* DC_SCRATCH */
+	DC_SCRATCH,
+	/* Last element */
+	DC_FIELD_MAX,
+};
+
+/* ISP1763 */
+/* Initialization Registers */
+#define ISP1763_DC_ADDRESS		0x00
+#define ISP1763_DC_MODE			0x0c
+#define ISP1763_DC_INTCONF		0x10
+#define ISP1763_DC_INTENABLE		0x14
+
+/* Data Flow Registers */
+#define ISP1763_DC_EPMAXPKTSZ		0x04
+#define ISP1763_DC_EPTYPE		0x08
+
+#define ISP1763_DC_BUFLEN		0x1c
+#define ISP1763_DC_BUFSTAT		0x1e
+#define ISP1763_DC_DATAPORT		0x20
+
+#define ISP1763_DC_CTRLFUNC		0x28
+#define ISP1763_DC_EPINDEX		0x2c
+
+/* DMA Registers */
+#define ISP1763_DC_DMACMD		0x30
+#define ISP1763_DC_DMATXCOUNT		0x34
+#define ISP1763_DC_DMACONF		0x38
+#define ISP1763_DC_DMAHW		0x3c
+#define ISP1763_DC_DMAINTREASON		0x50
+#define ISP1763_DC_DMAINTEN		0x54
+#define ISP1763_DC_DMAEP		0x58
+#define ISP1763_DC_DMABURSTCOUNT	0x64
+
+/* General Registers */
+#define ISP1763_DC_INTERRUPT		0x18
+#define ISP1763_DC_CHIPID_LOW		0x70
+#define ISP1763_DC_CHIPID_HIGH		0x72
+#define ISP1763_DC_FRAMENUM		0x74
+#define ISP1763_DC_SCRATCH		0x78
+#define ISP1763_DC_UNLOCKDEV		0x7c
+#define ISP1763_DC_INTPULSEWIDTH	0x80
+#define ISP1763_DC_TESTMODE		0x84
+
+#endif
diff --git a/drivers/usb/isp1760/isp1760-uboot.c b/drivers/usb/isp1760/isp1760-uboot.c
new file mode 100644
index 000000000000..203500a4cb7f
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-uboot.c
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the NXP ISP1760 chip
+ *
+ * Copyright 2021 Linaro, Rui Miguel Silva <rui.silva@linaro.org>
+ *
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <dm/device_compat.h>
+#include <dm/devres.h>
+#include <dm/lists.h>
+#include <linux/bug.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/usb_urb_compat.h>
+#include <log.h>
+#include <usb.h>
+
+#include "isp1760-core.h"
+#include "isp1760-hcd.h"
+#include "isp1760-regs.h"
+#include "isp1760-uboot.h"
+
+static int isp1760_msg_submit_control(struct udevice *dev,
+				      struct usb_device *udev,
+				      unsigned long pipe, void *buffer,
+				      int length, struct devrequest *setup)
+{
+	struct isp1760_host_data *host = dev_get_priv(dev);
+
+	return usb_urb_submit_control(&host->hcd, &host->urb, &host->hep, udev,
+				      pipe, buffer, length, setup, 0,
+				      host->host_speed);
+}
+
+static int isp1760_msg_submit_bulk(struct udevice *dev, struct usb_device *udev,
+				   unsigned long pipe, void *buffer, int length)
+{
+	struct isp1760_host_data *host = dev_get_priv(dev);
+
+	return usb_urb_submit_bulk(&host->hcd, &host->urb, &host->hep, udev,
+				   pipe, buffer, length);
+}
+
+static int isp1760_msg_submit_irq(struct udevice *dev, struct usb_device *udev,
+				  unsigned long pipe, void *buffer, int length,
+				  int interval, bool nonblock)
+{
+	struct isp1760_host_data *host = dev_get_priv(dev);
+
+	return usb_urb_submit_irq(&host->hcd, &host->urb, &host->hep, udev,
+				  pipe, buffer, length, interval);
+}
+
+static int isp1760_get_max_xfer_size(struct udevice *dev, size_t *size)
+{
+	struct isp1760_host_data *host = dev_get_priv(dev);
+	struct isp1760_hcd *priv = host->hcd.hcd_priv;
+	const struct isp1760_memory_layout *mem = priv->memory_layout;
+
+	*size = mem->blocks_size[ISP176x_BLOCK_NUM - 1];
+
+	return 0;
+}
+
+struct dm_usb_ops isp1760_usb_ops = {
+	.control		= isp1760_msg_submit_control,
+	.bulk			= isp1760_msg_submit_bulk,
+	.interrupt		= isp1760_msg_submit_irq,
+	.get_max_xfer_size	= isp1760_get_max_xfer_size,
+};
diff --git a/drivers/usb/isp1760/isp1760-uboot.h b/drivers/usb/isp1760/isp1760-uboot.h
new file mode 100644
index 000000000000..812355b48bcb
--- /dev/null
+++ b/drivers/usb/isp1760/isp1760-uboot.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Driver for the NXP ISP1760 chip
+ *
+ * Copyright 2021 Linaro, Rui Miguel Silva <rui.silva@linaro.org>
+ *
+ */
+
+#ifndef __ISP1760_UBOOT_H__
+#define __ISP1760_UBOOT_H__
+
+#include <linux/usb/usb_urb_compat.h>
+#include <usb.h>
+
+#include "isp1760-core.h"
+
+struct isp1760_host_data {
+	struct isp1760_hcd *priv;
+	struct usb_hcd hcd;
+	enum usb_device_speed host_speed;
+	struct usb_host_endpoint hep;
+	struct urb urb;
+};
+
+extern struct dm_usb_ops isp1760_usb_ops;
+
+#endif
