@@ -9,6 +9,14 @@ config DM_PWM
frequency/period can be controlled along with the proportion of that
time that the signal is high.
+config PWM_ASPEED
+ bool "Enable support for the Aspeed PWM"
+ depends on DM_PWM
+ help
+ This PWM is found on Ast2600 SoCs. It supports a programmable period
+ and duty cycle. It provides 16 channels which can be independently
+ programmed.
+
config PWM_AT91
bool "Enable support for PWM found on AT91 SoC's"
depends on DM_PWM && ARCH_AT91
@@ -10,6 +10,7 @@
obj-$(CONFIG_DM_PWM) += pwm-uclass.o
+obj-$(CONFIG_PWM_ASPEED) += pwm-aspeed.o
obj-$(CONFIG_PWM_AT91) += pwm-at91.o
obj-$(CONFIG_PWM_CROS_EC) += cros_ec_pwm.o
obj-$(CONFIG_PWM_EXYNOS) += exynos_pwm.o
new file mode 100644
@@ -0,0 +1,251 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2022 Aspeed Technology Inc.
+ *
+ * PWM controller driver for Aspeed ast2600 SoCs.
+ * This drivers doesn't support earlier version of the IP.
+ *
+ * The formula of pwm period duration:
+ * period duration = ((DIV_L + 1) * (PERIOD + 1) << DIV_H) / input-clk
+ *
+ * The formula of pwm duty cycle duration:
+ * duty cycle duration = period duration * DUTY_CYCLE_FALLING_POINT / (PERIOD + 1)
+ * = ((DIV_L + 1) * DUTY_CYCLE_FALLING_POINT << DIV_H) / input-clk
+ *
+ * The software driver fixes the period to 255, which causes the high-frequency
+ * precision of the PWM to be coarse, in exchange for the fineness of the duty cycle.
+ *
+ * Register usage:
+ * PIN_ENABLE: When it is unset the pwm controller will always output low to the extern.
+ * Use to determine whether the PWM channel is enabled or disabled
+ * CLK_ENABLE: When it is unset the pwm controller will reset the duty counter to 0 and
+ * output low to the PIN_ENABLE mux after that the driver can still change the pwm period
+ * and duty and the value will apply when CLK_ENABLE be set again.
+ * Use to determine whether duty_cycle bigger than 0.
+ * PWM_ASPEED_CTRL_INVERSE: When it is toggled the output value will inverse immediately.
+ * PWM_ASPEED_DUTY_CYCLE_FALLING_POINT/PWM_ASPEED_DUTY_CYCLE_RISING_POINT: When these two
+ * values are equal it means the duty cycle = 100%.
+ *
+ * Limitations:
+ * - When changing both duty cycle and period, we cannot prevent in
+ * software that the output might produce a period with mixed
+ * settings.
+ * - Disabling the PWM doesn't complete the current period.
+ *
+ * Improvements:
+ * - When only changing one of duty cycle or period, our pwm controller will not
+ * generate the glitch, the configure will change at next cycle of pwm.
+ * This improvement can disable/enable through PWM_ASPEED_CTRL_DUTY_SYNC_DISABLE.
+ */
+
+#include <common.h>
+#include <div64.h>
+#include <dm.h>
+#include <pwm.h>
+#include <clk.h>
+#include <reset.h>
+#include <regmap.h>
+#include <syscon.h>
+#include <dm/device_compat.h>
+#include <linux/math64.h>
+#include <linux/bitfield.h>
+#include <asm/io.h>
+
+/* The channel number of Aspeed pwm controller */
+#define PWM_ASPEED_NR_PWMS 16
+
+/* PWM Control Register */
+#define PWM_ASPEED_CTRL(ch) ((ch) * 0x10 + 0x00)
+#define PWM_ASPEED_CTRL_LOAD_SEL_RISING_AS_WDT BIT(19)
+#define PWM_ASPEED_CTRL_DUTY_LOAD_AS_WDT_ENABLE BIT(18)
+#define PWM_ASPEED_CTRL_DUTY_SYNC_DISABLE BIT(17)
+#define PWM_ASPEED_CTRL_CLK_ENABLE BIT(16)
+#define PWM_ASPEED_CTRL_LEVEL_OUTPUT BIT(15)
+#define PWM_ASPEED_CTRL_INVERSE BIT(14)
+#define PWM_ASPEED_CTRL_OPEN_DRAIN_ENABLE BIT(13)
+#define PWM_ASPEED_CTRL_PIN_ENABLE BIT(12)
+#define PWM_ASPEED_CTRL_CLK_DIV_H GENMASK(11, 8)
+#define PWM_ASPEED_CTRL_CLK_DIV_L GENMASK(7, 0)
+
+/* PWM Duty Cycle Register */
+#define PWM_ASPEED_DUTY_CYCLE(ch) ((ch) * 0x10 + 0x04)
+#define PWM_ASPEED_DUTY_CYCLE_PERIOD GENMASK(31, 24)
+#define PWM_ASPEED_DUTY_CYCLE_POINT_AS_WDT GENMASK(23, 16)
+#define PWM_ASPEED_DUTY_CYCLE_FALLING_POINT GENMASK(15, 8)
+#define PWM_ASPEED_DUTY_CYCLE_RISING_POINT GENMASK(7, 0)
+
+/* PWM fixed value */
+#define PWM_ASPEED_FIXED_PERIOD 0xff
+
+#define NSEC_PER_SEC 1000000000L
+
+struct aspeed_pwm_priv {
+ struct clk clk;
+ struct regmap *regmap;
+ struct reset_ctl reset;
+};
+
+static int aspeed_pwm_set_invert(struct udevice *dev, uint channel, bool polarity)
+{
+ struct aspeed_pwm_priv *priv = dev_get_priv(dev);
+
+ if (channel >= PWM_ASPEED_NR_PWMS)
+ return -EINVAL;
+
+ regmap_update_bits(priv->regmap, PWM_ASPEED_CTRL(channel),
+ PWM_ASPEED_CTRL_INVERSE,
+ FIELD_PREP(PWM_ASPEED_CTRL_INVERSE,
+ polarity));
+ return 0;
+}
+
+static int aspeed_pwm_set_enable(struct udevice *dev, uint channel, bool enable)
+{
+ struct aspeed_pwm_priv *priv = dev_get_priv(dev);
+
+ if (channel >= PWM_ASPEED_NR_PWMS)
+ return -EINVAL;
+
+ regmap_update_bits(priv->regmap, PWM_ASPEED_CTRL(channel),
+ PWM_ASPEED_CTRL_PIN_ENABLE,
+ enable ? PWM_ASPEED_CTRL_PIN_ENABLE : 0);
+ return 0;
+}
+
+static int aspeed_pwm_set_config(struct udevice *dev, uint channel,
+ uint period_ns, uint duty_ns)
+{
+ struct aspeed_pwm_priv *priv = dev_get_priv(dev);
+ u32 duty_pt;
+ unsigned long rate;
+ u64 div_h, div_l, divisor;
+ bool clk_en;
+
+ if (channel >= PWM_ASPEED_NR_PWMS)
+ return -EINVAL;
+ dev_dbg(dev, "expect period: %dns, duty_cycle: %dns\n", period_ns,
+ duty_ns);
+
+ rate = clk_get_rate(&priv->clk);
+ /*
+ * Pick the smallest value for div_h so that div_l can be the biggest
+ * which results in a finer resolution near the target period value.
+ */
+ divisor = (u64)NSEC_PER_SEC * (PWM_ASPEED_FIXED_PERIOD + 1) *
+ (PWM_ASPEED_CTRL_CLK_DIV_L + 1);
+ div_h = order_base_2(div64_u64((u64)rate * period_ns + divisor - 1, divisor));
+ if (div_h > 0xf)
+ div_h = 0xf;
+
+ divisor = ((u64)NSEC_PER_SEC * (PWM_ASPEED_FIXED_PERIOD + 1)) << div_h;
+ div_l = div64_u64((u64)rate * period_ns, divisor);
+
+ if (div_l == 0)
+ return -ERANGE;
+
+ div_l -= 1;
+
+ if (div_l > 255)
+ div_l = 255;
+
+ dev_dbg(dev, "clk source: %ld div_h %lld, div_l : %lld\n", rate, div_h,
+ div_l);
+ /* duty_pt = duty_cycle * (PERIOD + 1) / period */
+ duty_pt = div64_u64(duty_ns * (u64)rate,
+ (u64)NSEC_PER_SEC * (div_l + 1) << div_h);
+ dev_dbg(dev, "duty_cycle = %d, duty_pt = %d\n", duty_ns,
+ duty_pt);
+
+ if (duty_pt == 0) {
+ clk_en = 0;
+ } else {
+ clk_en = 1;
+ if (duty_pt >= (PWM_ASPEED_FIXED_PERIOD + 1))
+ duty_pt = 0;
+ /*
+ * Fixed DUTY_CYCLE_PERIOD to its max value to get a
+ * fine-grained resolution for duty_cycle at the expense of a
+ * coarser period resolution.
+ */
+ regmap_update_bits(priv->regmap, PWM_ASPEED_DUTY_CYCLE(channel),
+ PWM_ASPEED_DUTY_CYCLE_PERIOD |
+ PWM_ASPEED_DUTY_CYCLE_RISING_POINT |
+ PWM_ASPEED_DUTY_CYCLE_FALLING_POINT,
+ FIELD_PREP(PWM_ASPEED_DUTY_CYCLE_PERIOD,
+ PWM_ASPEED_FIXED_PERIOD) |
+ FIELD_PREP(PWM_ASPEED_DUTY_CYCLE_FALLING_POINT,
+ duty_pt));
+ }
+
+ regmap_update_bits(priv->regmap, PWM_ASPEED_CTRL(channel),
+ PWM_ASPEED_CTRL_CLK_DIV_H |
+ PWM_ASPEED_CTRL_CLK_DIV_L |
+ PWM_ASPEED_CTRL_CLK_ENABLE,
+ FIELD_PREP(PWM_ASPEED_CTRL_CLK_DIV_H, div_h) |
+ FIELD_PREP(PWM_ASPEED_CTRL_CLK_DIV_L, div_l) |
+ FIELD_PREP(PWM_ASPEED_CTRL_CLK_ENABLE, clk_en));
+ return 0;
+}
+
+static int aspeed_pwm_probe(struct udevice *dev)
+{
+ int ret;
+ struct aspeed_pwm_priv *priv = dev_get_priv(dev);
+ struct udevice *parent_dev = dev_get_parent(dev);
+
+ priv->regmap = syscon_node_to_regmap(dev_ofnode(dev->parent));
+ if (IS_ERR(priv->regmap)) {
+ dev_err(dev, "Couldn't get regmap\n");
+ return PTR_ERR(priv->regmap);
+ }
+
+ ret = clk_get_by_index(parent_dev, 0, &priv->clk);
+ if (ret < 0) {
+ dev_err(dev, "get clock failed\n");
+ return ret;
+ }
+
+ ret = reset_get_by_index(parent_dev, 0, &priv->reset);
+ if (ret) {
+ dev_err(dev, "get reset failed\n");
+ return ret;
+ }
+ ret = reset_deassert(&priv->reset);
+ if (ret) {
+ dev_err(dev, "cannot deassert reset control: %pe\n",
+ ERR_PTR(ret));
+ return ret;
+ }
+
+ return 0;
+}
+
+static int aspeed_pwm_remove(struct udevice *dev)
+{
+ struct aspeed_pwm_priv *priv = dev_get_priv(dev);
+
+ reset_assert(&priv->reset);
+
+ return 0;
+}
+
+static const struct pwm_ops aspeed_pwm_ops = {
+ .set_invert = aspeed_pwm_set_invert,
+ .set_config = aspeed_pwm_set_config,
+ .set_enable = aspeed_pwm_set_enable,
+};
+
+static const struct udevice_id aspeed_pwm_ids[] = {
+ { .compatible = "aspeed,ast2600-pwm" },
+ { }
+};
+
+U_BOOT_DRIVER(aspeed_pwm) = {
+ .name = "aspeed_pwm",
+ .id = UCLASS_PWM,
+ .of_match = aspeed_pwm_ids,
+ .ops = &aspeed_pwm_ops,
+ .probe = aspeed_pwm_probe,
+ .remove = aspeed_pwm_remove,
+ .priv_auto = sizeof(struct aspeed_pwm_priv),
+};
This patch add the support of PWM controller which can be found at aspeed ast2600 soc. The pwm supoorts up to 16 channels and it's part function of multi-function device "pwm-tach controller". Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> --- drivers/pwm/Kconfig | 8 ++ drivers/pwm/Makefile | 1 + drivers/pwm/pwm-aspeed.c | 251 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 260 insertions(+) create mode 100644 drivers/pwm/pwm-aspeed.c