diff mbox series

[u-boot-marvell,v3,8/9] arm: mvebu: spl: Use IS_ENABLED() instead of #ifdef where possible

Message ID 20211214132222.21324-9-kabel@kernel.org
State Changes Requested
Delegated to: Stefan Roese
Headers show
Series More verifications for kwbimage in SPL | expand

Commit Message

Marek Behún Dec. 14, 2021, 1:22 p.m. UTC 
From: Marek Behún <marek.behun@nic.cz>

Use the preferred
  if (IS_ENABLED(X))
instead of
  #ifdef X
where possible.

There are still places where this is not possible or is more complicated
to convert in this file. Leave those be for now.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
---
 arch/arm/mach-mvebu/spl.c | 43 ++++++++++++++++-----------------------
 1 file changed, 18 insertions(+), 25 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/mach-mvebu/spl.c b/arch/arm/mach-mvebu/spl.c
index 97cb70f147..6e2a9e38ec 100644
--- a/arch/arm/mach-mvebu/spl.c
+++ b/arch/arm/mach-mvebu/spl.c
@@ -150,26 +150,24 @@  int spl_parse_board_header(struct spl_image_info *spl_image,
 		return -EINVAL;
 	}
 
-#ifdef CONFIG_SPL_SPI_FLASH_SUPPORT
-	if (bootdev->boot_device == BOOT_DEVICE_SPI &&
+	if (IS_ENABLED(CONFIG_SPL_SPI_FLASH_SUPPORT) &&
+	    bootdev->boot_device == BOOT_DEVICE_SPI &&
 	    mhdr->blockid != IBR_HDR_SPI_ID) {
 		printf("ERROR: Wrong blockid (%u) in SPI kwbimage\n",
 		       mhdr->blockid);
 		return -EINVAL;
 	}
-#endif
 
-#ifdef CONFIG_SPL_SATA
-	if (bootdev->boot_device == BOOT_DEVICE_SATA &&
+	if (IS_ENABLED(CONFIG_SPL_SATA) &&
+	    bootdev->boot_device == BOOT_DEVICE_SATA &&
 	    mhdr->blockid != IBR_HDR_SATA_ID) {
 		printf("ERROR: Wrong blockid (%u) in SATA kwbimage\n",
 		       mhdr->blockid);
 		return -EINVAL;
 	}
-#endif
 
-#ifdef CONFIG_SPL_MMC
-	if ((bootdev->boot_device == BOOT_DEVICE_MMC1 ||
+	if (IS_ENABLED(CONFIG_SPL_MMC) &&
+	    (bootdev->boot_device == BOOT_DEVICE_MMC1 ||
 	     bootdev->boot_device == BOOT_DEVICE_MMC2 ||
 	     bootdev->boot_device == BOOT_DEVICE_MMC2_2) &&
 	    mhdr->blockid != IBR_HDR_SDIO_ID) {
@@ -177,18 +175,16 @@  int spl_parse_board_header(struct spl_image_info *spl_image,
 		       mhdr->blockid);
 		return -EINVAL;
 	}
-#endif
 
 	spl_image->offset = mhdr->srcaddr;
 
-#ifdef CONFIG_SPL_SATA
 	/*
 	 * For SATA srcaddr is specified in number of sectors.
 	 * The main header is must be stored at sector number 1.
 	 * This expects that sector size is 512 bytes and recalculates
 	 * data offset to bytes relative to the main header.
 	 */
-	if (mhdr->blockid == IBR_HDR_SATA_ID) {
+	if (IS_ENABLED(CONFIG_SPL_SATA) && mhdr->blockid == IBR_HDR_SATA_ID) {
 		if (spl_image->offset < 1) {
 			printf("ERROR: Wrong srcaddr (%u) in SATA kwbimage\n",
 			       spl_image->offset);
@@ -197,17 +193,14 @@  int spl_parse_board_header(struct spl_image_info *spl_image,
 		spl_image->offset -= 1;
 		spl_image->offset *= 512;
 	}
-#endif
 
-#ifdef CONFIG_SPL_MMC
 	/*
 	 * For SDIO (eMMC) srcaddr is specified in number of sectors.
 	 * This expects that sector size is 512 bytes and recalculates
 	 * data offset to bytes.
 	 */
-	if (mhdr->blockid == IBR_HDR_SDIO_ID)
+	if (IS_ENABLED(CONFIG_SPL_MMC) && mhdr->blockid == IBR_HDR_SDIO_ID)
 		spl_image->offset *= 512;
-#endif
 
 	if (spl_image->offset % 4 != 0) {
 		printf("ERROR: Wrong srcaddr (%u) in kwbimage\n",
@@ -340,17 +333,17 @@  void board_init_f(ulong dummy)
 	timer_init();
 
 	/* Armada 375 does not support SerDes and DDR3 init yet */
-#if !defined(CONFIG_ARMADA_375)
-	/* First init the serdes PHY's */
-	serdes_phy_config();
-
-	/* Setup DDR */
-	ret = ddr3_init();
-	if (ret) {
-		debug("ddr3_init() failed: %d\n", ret);
-		hang();
+	if (!IS_ENABLED(CONFIG_ARMADA_375)) {
+		/* First init the serdes PHY's */
+		serdes_phy_config();
+
+		/* Setup DDR */
+		ret = ddr3_init();
+		if (ret) {
+			debug("ddr3_init() failed: %d\n", ret);
+			hang();
+		}
 	}
-#endif
 
 	/* Initialize Auto Voltage Scaling */
 	mv_avs_init();