@@ -103,21 +103,29 @@ static int mmc_resource_init(int sdc_no)
}
#endif
+/*
+ * All A64 and later MMC controllers feature auto-calibration. This would
+ * normally be detected via the compatible string, but we need something
+ * which works in the SPL as well.
+ */
+static bool sunxi_mmc_can_calibrate(void)
+{
+ return IS_ENABLED(CONFIG_MACH_SUN50I) ||
+ IS_ENABLED(CONFIG_MACH_SUN50I_H5) ||
+ IS_ENABLED(CONFIG_SUN50I_GEN_H6) ||
+ IS_ENABLED(CONFIG_MACH_SUN8I_R40);
+}
+
static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz)
{
unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly;
bool new_mode = IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE);
- bool calibrate = false;
u32 val = 0;
/* A83T support new mode only on eMMC */
if (IS_ENABLED(CONFIG_MACH_SUN8I_A83T) && priv->mmc_no != 2)
new_mode = false;
-#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_SUN50I_GEN_H6)
- calibrate = true;
-#endif
-
if (hz <= 24000000) {
pll = CCM_MMC_CTRL_OSCM24;
pll_hz = 24000000;
@@ -179,7 +187,9 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz)
if (new_mode) {
val |= CCM_MMC_CTRL_MODE_SEL_NEW;
setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW);
- } else if (!calibrate) {
+ }
+
+ if (!sunxi_mmc_can_calibrate()) {
/*
* Use hardcoded delay values if controller doesn't support
* calibration
@@ -237,14 +247,15 @@ static int mmc_config_clock(struct sunxi_mmc_priv *priv, struct mmc *mmc)
rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK;
writel(rval, &priv->reg->clkcr);
-#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_SUN50I_GEN_H6)
+#if defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_SUN50I_GEN_H6)
/* A64 supports calibration of delays on MMC controller and we
* have to set delay of zero before starting calibration.
* Allwinner BSP driver sets a delay only in the case of
* using HS400 which is not supported by mainline U-Boot or
* Linux at the moment
*/
- writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl);
+ if (sunxi_mmc_can_calibrate())
+ writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl);
#endif
/* Re-enable Clock */
Newer SoCs have a self calibration feature, which avoids us writing hard coded phase delay values into the controller. Consolidate the code by avoiding unnecessary #ifdefs, and also enabling the feature for all those newer SoCs. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- drivers/mmc/sunxi_mmc.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-)