diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 1dd6c4b2e8..cb2b2ae6fb 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -173,11 +173,13 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-g12a-sei510.dtb \
 	meson-g12b-gtking.dtb \
 	meson-g12b-gtking-pro.dtb \
+	meson-g12b-gsking-x.dtb \
 	meson-g12b-odroid-n2.dtb \
 	meson-g12b-odroid-n2-plus.dtb \
 	meson-g12b-a311d-khadas-vim3.dtb \
 	meson-sm1-khadas-vim3l.dtb \
 	meson-sm1-odroid-c4.dtb \
+	meson-sm1-odroid-hc4.dtb \
 	meson-sm1-sei610.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
diff --git a/arch/arm/dts/meson-axg-s400.dts b/arch/arm/dts/meson-axg-s400.dts
index cb1360ae12..359589d1df 100644
--- a/arch/arm/dts/meson-axg-s400.dts
+++ b/arch/arm/dts/meson-axg-s400.dts
@@ -441,6 +441,16 @@
 	status = "okay";
 };
 
+&pcieA {
+	reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pcieB {
+	reset-gpios = <&gpio GPIOZ_10 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
 &pwm_ab {
 	status = "okay";
 	pinctrl-0 = <&pwm_a_x20_pins>;
@@ -584,3 +594,9 @@
 	pinctrl-0 = <&uart_ao_a_pins>;
 	pinctrl-names = "default";
 };
+
+&usb {
+	status = "okay";
+	dr_mode = "otg";
+	vbus-supply = <&usb_pwr>;
+};
diff --git a/arch/arm/dts/meson-axg.dtsi b/arch/arm/dts/meson-axg.dtsi
index b9efc84692..d945c84ab6 100644
--- a/arch/arm/dts/meson-axg.dtsi
+++ b/arch/arm/dts/meson-axg.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/reset/amlogic,meson-axg-audio-arb.h>
 #include <dt-bindings/reset/amlogic,meson-axg-reset.h>
+#include <dt-bindings/power/meson-axg-power.h>
 
 / {
 	compatible = "amlogic,meson-axg";
@@ -171,6 +172,98 @@
 		#size-cells = <2>;
 		ranges;
 
+		pcieA: pcie@f9800000 {
+			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
+			reg = <0x0 0xf9800000 0x0 0x400000>,
+			      <0x0 0xff646000 0x0 0x2000>,
+			      <0x0 0xf9f00000 0x0 0x100000>;
+			reg-names = "elbi", "cfg", "config";
+			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x82000000 0 0xf9c00000 0x0 0xf9c00000 0 0x00300000>;
+
+			clocks = <&clkc CLKID_USB>, <&clkc CLKID_PCIE_A>, <&clkc CLKID_PCIE_CML_EN0>;
+			clock-names = "general", "pclk", "port";
+			resets = <&reset RESET_PCIE_A>, <&reset RESET_PCIE_APB>;
+			reset-names = "port", "apb";
+			num-lanes = <1>;
+			phys = <&pcie_phy>;
+			phy-names = "pcie";
+			status = "disabled";
+		};
+
+		pcieB: pcie@fa000000 {
+			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
+			reg = <0x0 0xfa000000 0x0 0x400000>,
+			      <0x0 0xff648000 0x0 0x2000>,
+			      <0x0 0xfa400000 0x0 0x100000>;
+			reg-names = "elbi", "cfg", "config";
+			interrupts = <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x82000000 0 0xfa500000 0x0 0xfa500000 0 0x00300000>;
+
+			clocks = <&clkc CLKID_USB>, <&clkc CLKID_PCIE_B>, <&clkc CLKID_PCIE_CML_EN1>;
+			clock-names = "general", "pclk", "port";
+			resets = <&reset RESET_PCIE_B>, <&reset RESET_PCIE_APB>;
+			reset-names = "port", "apb";
+			num-lanes = <1>;
+			phys = <&pcie_phy>;
+			phy-names = "pcie";
+			status = "disabled";
+		};
+
+		usb: usb@ffe09080 {
+			compatible = "amlogic,meson-axg-usb-ctrl";
+			reg = <0x0 0xffe09080 0x0 0x20>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1_DDR_BRIDGE>;
+			clock-names = "usb_ctrl", "ddr";
+			resets = <&reset RESET_USB_OTG>;
+
+			dr_mode = "otg";
+
+			phys = <&usb2_phy1>;
+			phy-names = "usb2-phy1";
+
+			dwc2: usb@ff400000 {
+				compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+				reg = <0x0 0xff400000 0x0 0x40000>;
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc CLKID_USB1>;
+				clock-names = "otg";
+				phys = <&usb2_phy1>;
+				dr_mode = "peripheral";
+				g-rx-fifo-size = <192>;
+				g-np-tx-fifo-size = <128>;
+				g-tx-fifo-size = <128 128 16 16 16>;
+			};
+
+			dwc3: usb@ff500000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff500000 0x0 0x100000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				maximum-speed = "high-speed";
+				snps,dis_u2_susphy_quirk;
+			};
+		};
+
 		ethmac: ethernet@ff3f0000 {
 			compatible = "amlogic,meson-axg-dwmac",
 				     "snps,dwmac-3.70a",
@@ -187,9 +280,19 @@
 				      "timing-adjustment";
 			rx-fifo-depth = <4096>;
 			tx-fifo-depth = <2048>;
+			power-domains = <&pwrc PWRC_AXG_ETHERNET_MEM_ID>;
 			status = "disabled";
 		};
 
+		pcie_phy: phy@ff644000 {
+			compatible = "amlogic,axg-pcie-phy";
+			reg = <0x0 0xff644000 0x0 0x1c>;
+			resets = <&reset RESET_PCIE_PHY>;
+			phys = <&mipi_pcie_analog_dphy>;
+			phy-names = "analog";
+			#phy-cells = <0>;
+		};
+
 		pdm: audio-controller@ff632000 {
 			compatible = "amlogic,axg-pdm";
 			reg = <0x0 0xff632000 0x0 0x34>;
@@ -1117,6 +1220,52 @@
 					clocks = <&xtal>;
 					clock-names = "xtal";
 				};
+
+				pwrc: power-controller {
+					compatible = "amlogic,meson-axg-pwrc";
+					#power-domain-cells = <1>;
+					amlogic,ao-sysctrl = <&sysctrl_AO>;
+					resets = <&reset RESET_VIU>,
+						 <&reset RESET_VENC>,
+						 <&reset RESET_VCBUS>,
+						 <&reset RESET_VENCL>,
+						 <&reset RESET_VID_LOCK>;
+					reset-names = "viu", "venc", "vcbus",
+						      "vencl", "vid_lock";
+					clocks = <&clkc CLKID_VPU>,
+						 <&clkc CLKID_VAPB>;
+					clock-names = "vpu", "vapb";
+					/*
+					 * VPU clocking is provided by two identical clock paths
+					 * VPU_0 and VPU_1 muxed to a single clock by a glitch
+					 * free mux to safely change frequency while running.
+					 * Same for VAPB but with a final gate after the glitch free mux.
+					 */
+					assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+							  <&clkc CLKID_VPU_0>,
+							  <&clkc CLKID_VPU>, /* Glitch free mux */
+							  <&clkc CLKID_VAPB_0_SEL>,
+							  <&clkc CLKID_VAPB_0>,
+							  <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+					assigned-clock-parents = <&clkc CLKID_FCLK_DIV4>,
+								 <0>, /* Do Nothing */
+								 <&clkc CLKID_VPU_0>,
+								 <&clkc CLKID_FCLK_DIV4>,
+								 <0>, /* Do Nothing */
+								 <&clkc CLKID_VAPB_0>;
+					assigned-clock-rates = <0>, /* Do Nothing */
+							       <250000000>,
+							       <0>, /* Do Nothing */
+							       <0>, /* Do Nothing */
+							       <250000000>,
+							       <0>; /* Do Nothing */
+				};
+
+				mipi_pcie_analog_dphy: phy {
+					compatible = "amlogic,axg-mipi-pcie-analog-phy";
+					#phy-cells = <0>;
+					status = "disabled";
+				};
 			};
 		};
 
@@ -1129,6 +1278,19 @@
 			#mbox-cells = <1>;
 		};
 
+		mipi_dphy: phy@ff640000 {
+			compatible = "amlogic,axg-mipi-dphy";
+			reg = <0x0 0xff640000 0x0 0x100>;
+			clocks = <&clkc CLKID_MIPI_DSI_PHY>;
+			clock-names = "pclk";
+			resets = <&reset RESET_MIPI_PHY>;
+			reset-names = "phy";
+			phys = <&mipi_pcie_analog_dphy>;
+			phy-names = "analog";
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		audio: bus@ff642000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xff642000 0x0 0x2000>;
@@ -1563,6 +1725,15 @@
 			};
 		};
 
+		ge2d: ge2d@ff940000 {
+			compatible = "amlogic,axg-ge2d";
+			reg = <0x0 0xff940000 0x0 0x10000>;
+			interrupts = <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkc CLKID_VAPB>;
+			resets = <&reset RESET_GE2D>;
+			reset-names = "core";
+		};
+
 		gic: interrupt-controller@ffc01000 {
 			compatible = "arm,gic-400";
 			reg = <0x0 0xffc01000 0 0x1000>,
@@ -1734,6 +1905,16 @@
 				clock-names = "core", "clkin0", "clkin1";
 				resets = <&reset RESET_SD_EMMC_C>;
 			};
+
+			usb2_phy1: phy@9020 {
+				compatible = "amlogic,meson-gxl-usb2-phy";
+				#phy-cells = <0>;
+				reg = <0x0 0x9020 0x0 0x20>;
+				clocks = <&clkc CLKID_USB>;
+				clock-names = "phy";
+				resets = <&reset RESET_USB_OTG>;
+				reset-names = "phy";
+			};
 		};
 
 		sram: sram@fffc0000 {
diff --git a/arch/arm/dts/meson-g12-common.dtsi b/arch/arm/dts/meson-g12-common.dtsi
index 1e83ec5b8c..b858c5e43c 100644
--- a/arch/arm/dts/meson-g12-common.dtsi
+++ b/arch/arm/dts/meson-g12-common.dtsi
@@ -209,7 +209,7 @@
 		};
 
 		ethmac: ethernet@ff3f0000 {
-			compatible = "amlogic,meson-axg-dwmac",
+			compatible = "amlogic,meson-g12a-dwmac",
 				     "snps,dwmac-3.70a",
 				     "snps,dwmac";
 			reg = <0x0 0xff3f0000 0x0 0x10000>,
@@ -282,6 +282,8 @@
 				hwrng: rng@218 {
 					compatible = "amlogic,meson-rng";
 					reg = <0x0 0x218 0x0 0x4>;
+					clocks = <&clkc CLKID_RNG0>;
+					clock-names = "core";
 				};
 			};
 
@@ -2179,6 +2181,12 @@
 				amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
 			};
 
+			watchdog: wdt@f0d0 {
+				compatible = "amlogic,meson-gxbb-wdt";
+				reg = <0x0 0xf0d0 0x0 0x10>;
+				clocks = <&xtal>;
+			};
+
 			spicc0: spi@13000 {
 				compatible = "amlogic,meson-g12a-spicc";
 				reg = <0x0 0x13000 0x0 0x44>;
@@ -2380,7 +2388,7 @@
 				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 				dr_mode = "host";
 				snps,dis_u2_susphy_quirk;
-				snps,quirk-frame-length-adjustment;
+				snps,quirk-frame-length-adjustment = <0x20>;
 				snps,parkmode-disable-ss-quirk;
 			};
 		};
diff --git a/arch/arm/dts/meson-g12a-sei510.dts b/arch/arm/dts/meson-g12a-sei510.dts
index b00d0468c7..81269ccc24 100644
--- a/arch/arm/dts/meson-g12a-sei510.dts
+++ b/arch/arm/dts/meson-g12a-sei510.dts
@@ -181,7 +181,7 @@
 
 	sound {
 		compatible = "amlogic,axg-sound-card";
-		model = "G12A-SEI510";
+		model = "SEI510";
 		audio-aux-devs = <&tdmout_a>, <&tdmout_b>,
 				 <&tdmin_a>, <&tdmin_b>;
 		audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
diff --git a/arch/arm/dts/meson-g12b-gsking-x.dts b/arch/arm/dts/meson-g12b-gsking-x.dts
new file mode 100644
index 0000000000..211191f663
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-gsking-x.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-w400.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "azw,gsking-x", "amlogic,g12b";
+	model = "Beelink GS-King X";
+
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &vrtc;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <100>;
+
+		power-button {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "GSKING-X";
+		audio-aux-devs = <&tdmout_a>;
+		audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_A IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_A IN 2", "FRDDR_C OUT 1",
+				"TDM_A Playback", "TDMOUT_A OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_a>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>;
+			};
+		};
+
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+	pinctrl-names = "default";
+
+	rtc: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		wakeup-source;
+	};
+};
+
+&tdmif_a {
+	status = "okay";
+};
+
+&tdmout_a {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
diff --git a/arch/arm/dts/meson-g12b-gtking-pro.dts b/arch/arm/dts/meson-g12b-gtking-pro.dts
index f0c56a16af..0e331aa5a2 100644
--- a/arch/arm/dts/meson-g12b-gtking-pro.dts
+++ b/arch/arm/dts/meson-g12b-gtking-pro.dts
@@ -14,6 +14,11 @@
 	compatible = "azw,gtking", "amlogic,g12b";
 	model = "Beelink GT-King Pro";
 
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &vrtc;
+	};
+
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
 		#address-cells = <1>;
@@ -39,7 +44,7 @@
 
 	sound {
 		compatible = "amlogic,axg-sound-card";
-		model = "G12B-GTKING-PRO";
+		model = "GTKING-PRO";
 		audio-aux-devs = <&tdmout_b>;
 		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
 				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
@@ -112,6 +117,18 @@
 	status = "okay";
 };
 
+&i2c3 {
+	status = "okay";
+	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+	pinctrl-names = "default";
+
+	rtc: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		wakeup-source;
+	};
+};
+
 &tdmif_b {
 	status = "okay";
 };
diff --git a/arch/arm/dts/meson-g12b-gtking.dts b/arch/arm/dts/meson-g12b-gtking.dts
index eeb7bc5539..a7db84a500 100644
--- a/arch/arm/dts/meson-g12b-gtking.dts
+++ b/arch/arm/dts/meson-g12b-gtking.dts
@@ -14,6 +14,11 @@
 	compatible = "azw,gtking", "amlogic,g12b";
 	model = "Beelink GT-King";
 
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &vrtc;
+	};
+
 	spdif_dit: audio-codec-1 {
 		#sound-dai-cells = <0>;
 		compatible = "linux,spdif-dit";
@@ -23,7 +28,7 @@
 
 	sound {
 		compatible = "amlogic,axg-sound-card";
-		model = "G12B-GTKING";
+		model = "GTKING";
 		audio-aux-devs = <&tdmout_b>;
 		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
 				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
@@ -122,6 +127,19 @@
 	status = "okay";
 };
 
+
+&i2c3 {
+	status = "okay";
+	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+	pinctrl-names = "default";
+
+	rtc: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		wakeup-source;
+	};
+};
+
 &spdifout {
 	pinctrl-0 = <&spdif_out_h_pins>;
 	pinctrl-names = "default";
diff --git a/arch/arm/dts/meson-g12b-odroid-n2-plus.dts b/arch/arm/dts/meson-g12b-odroid-n2-plus.dts
index 5de2815ba9..ce1198ad34 100644
--- a/arch/arm/dts/meson-g12b-odroid-n2-plus.dts
+++ b/arch/arm/dts/meson-g12b-odroid-n2-plus.dts
@@ -19,7 +19,7 @@
 	regulator-min-microvolt = <680000>;
 	regulator-max-microvolt = <1040000>;
 
-	pwms = <&pwm_AO_cd 1 1500 0>;
+	pwms = <&pwm_ab 0 1500 0>;
 };
 
 &vddcpu_b {
diff --git a/arch/arm/dts/meson-g12b-odroid-n2.dtsi b/arch/arm/dts/meson-g12b-odroid-n2.dtsi
index 6982632ae6..58ce569b2a 100644
--- a/arch/arm/dts/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm/dts/meson-g12b-odroid-n2.dtsi
@@ -13,6 +13,8 @@
 	aliases {
 		serial0 = &uart_AO;
 		ethernet0 = &ethmac;
+		rtc0 = &rtc;
+		rtc1 = &vrtc;
 	};
 
 	dioo2133: audio-amplifier-0 {
@@ -211,7 +213,7 @@
 
 	sound {
 		compatible = "amlogic,axg-sound-card";
-		model = "G12B-ODROID-N2";
+		model = "ODROID-N2";
 		audio-widgets = "Line", "Lineout";
 		audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>,
 				 <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>,
@@ -413,7 +415,7 @@
 		max-speed = <1000>;
 
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
 
 		interrupt-parent = <&gpio_intc>;
@@ -478,6 +480,18 @@
 	linux,rc-map-name = "rc-odroid";
 };
 
+&i2c3 {
+	status = "okay";
+	pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+	pinctrl-names = "default";
+
+	rtc: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		wakeup-source;
+	};
+};
+
 &pwm_ab {
 	pinctrl-0 = <&pwm_a_e_pins>;
 	pinctrl-names = "default";
diff --git a/arch/arm/dts/meson-g12b-w400.dtsi b/arch/arm/dts/meson-g12b-w400.dtsi
index 2802ddbb83..feb0885047 100644
--- a/arch/arm/dts/meson-g12b-w400.dtsi
+++ b/arch/arm/dts/meson-g12b-w400.dtsi
@@ -264,7 +264,7 @@
 		max-speed = <1000>;
 
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
 
 		interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm/dts/meson-g12b.dtsi b/arch/arm/dts/meson-g12b.dtsi
index 9b8548e5f6..ee8fcae9f9 100644
--- a/arch/arm/dts/meson-g12b.dtsi
+++ b/arch/arm/dts/meson-g12b.dtsi
@@ -135,3 +135,7 @@
 		};
 	};
 };
+
+&mali {
+	dma-coherent;
+};
diff --git a/arch/arm/dts/meson-gx-libretech-pc.dtsi b/arch/arm/dts/meson-gx-libretech-pc.dtsi
index c2480bab8d..2d7032f41e 100644
--- a/arch/arm/dts/meson-gx-libretech-pc.dtsi
+++ b/arch/arm/dts/meson-gx-libretech-pc.dtsi
@@ -186,7 +186,7 @@
 
 	sound {
 		compatible = "amlogic,gx-sound-card";
-		model = "GXL-LIBRETECH-S9XX-PC";
+		model = "LIBRETECH-PC";
 		audio-aux-devs = <&dio2133>;
 		audio-widgets = "Speaker", "7J4-14 LEFT",
 				"Speaker", "7J4-11 RIGHT";
diff --git a/arch/arm/dts/meson-gx-p23x-q20x.dtsi b/arch/arm/dts/meson-gx-p23x-q20x.dtsi
index 6b57e15aad..dafc841f7c 100644
--- a/arch/arm/dts/meson-gx-p23x-q20x.dtsi
+++ b/arch/arm/dts/meson-gx-p23x-q20x.dtsi
@@ -121,7 +121,7 @@
 
 	sound {
 		compatible = "amlogic,gx-sound-card";
-		model = "GX-P230-Q200";
+		model = "P230-Q200";
 		audio-aux-devs = <&dio2133>;
 		audio-widgets = "Line", "Lineout";
 		audio-routing = "AU2 INL", "ACODEC LOLP",
diff --git a/arch/arm/dts/meson-gxbb-nanopi-k2.dts b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
index 7be3e35409..7273eed529 100644
--- a/arch/arm/dts/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm/dts/meson-gxbb-nanopi-k2.dts
@@ -7,6 +7,7 @@
 
 #include "meson-gxbb.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/meson-aiu.h>
 
 / {
 	compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
@@ -130,6 +131,45 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "NANOPI-K2";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&aiu {
+	status = "okay";
 };
 
 &cec_AO {
@@ -165,7 +205,7 @@
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 			interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm/dts/meson-gxbb-odroidc2.dts b/arch/arm/dts/meson-gxbb-odroidc2.dts
index 70fcfb7b06..bfaf7f41a2 100644
--- a/arch/arm/dts/meson-gxbb-odroidc2.dts
+++ b/arch/arm/dts/meson-gxbb-odroidc2.dts
@@ -9,6 +9,7 @@
 
 #include "meson-gxbb.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/meson-aiu.h>
 
 / {
 	compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
@@ -172,6 +173,45 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "ODROID-C2";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&aiu {
+	status = "okay";
 };
 
 &cec_AO {
@@ -200,7 +240,7 @@
 			reg = <0>;
 
 			reset-assert-us = <10000>;
-			reset-deassert-us = <30000>;
+			reset-deassert-us = <80000>;
 			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 			interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm/dts/meson-gxl-s805x-libretech-ac.dts b/arch/arm/dts/meson-gxl-s805x-libretech-ac.dts
index 9e43f4dca9..2d769203f6 100644
--- a/arch/arm/dts/meson-gxl-s805x-libretech-ac.dts
+++ b/arch/arm/dts/meson-gxl-s805x-libretech-ac.dts
@@ -118,7 +118,7 @@
 
 	sound {
 		compatible = "amlogic,gx-sound-card";
-		model = "GXL-LIBRETECH-S805X-AC";
+		model = "LIBRETECH-AC";
 		audio-widgets = "Speaker", "9J5-3 LEFT",
 				"Speaker", "9J5-2 RIGHT";
 		audio-routing = "9J5-3 LEFT", "ACODEC LOLN",
diff --git a/arch/arm/dts/meson-gxl-s905x-khadas-vim.dts b/arch/arm/dts/meson-gxl-s905x-khadas-vim.dts
index 8bcdffdf55..60feac0179 100644
--- a/arch/arm/dts/meson-gxl-s905x-khadas-vim.dts
+++ b/arch/arm/dts/meson-gxl-s905x-khadas-vim.dts
@@ -5,9 +5,9 @@
 
 /dts-v1/;
 
-#include <dt-bindings/input/input.h>
-
 #include "meson-gxl-s905x-p212.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/meson-aiu.h>
 
 / {
 	compatible = "khadas,vim", "amlogic,s905x", "amlogic,meson-gxl";
@@ -42,10 +42,10 @@
 		};
 	};
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		power {
+		led-1 {
 			label = "vim:red:power";
 			pwms = <&pwm_AO_ab 1 7812500 0>;
 			max-brightness = <255>;
@@ -63,6 +63,45 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "KHADAS-VIM";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&aiu {
+	status = "okay";
 };
 
 &cec_AO {
@@ -97,8 +136,7 @@
 	pinctrl-names = "default";
 
 	rtc: rtc@51 {
-		/* has to be enabled manually when a battery is connected: */
-		status = "disabled";
+		status = "okay";
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
diff --git a/arch/arm/dts/meson-gxl-s905x-libretech-cc-v2.dts b/arch/arm/dts/meson-gxl-s905x-libretech-cc-v2.dts
index 675eaa8796..93d8f8aff7 100644
--- a/arch/arm/dts/meson-gxl-s905x-libretech-cc-v2.dts
+++ b/arch/arm/dts/meson-gxl-s905x-libretech-cc-v2.dts
@@ -84,7 +84,6 @@
 		regulator-always-on;
 	};
 
-
 	vcck: regulator-vcck {
 		compatible = "regulator-fixed";
 		regulator-name = "VCCK";
@@ -124,7 +123,6 @@
 		regulator-always-on;
 	};
 
-
 	vddio_card: regulator-vddio-card {
 		compatible = "regulator-gpio";
 		regulator-name = "VDDIO_CARD";
@@ -161,7 +159,7 @@
 
 	sound {
 		compatible = "amlogic,gx-sound-card";
-		model = "GXL-LIBRETECH-S905X-CC-V2";
+		model = "LIBRETECH-CC-V2";
 		assigned-clocks = <&clkc CLKID_MPLL0>,
 				  <&clkc CLKID_MPLL1>,
 				  <&clkc CLKID_MPLL2>;
@@ -195,7 +193,6 @@
 	};
 };
 
-
 &aiu {
 	status = "okay";
 };
@@ -207,7 +204,6 @@
 	hdmi-phandle = <&hdmi_tx>;
 };
 
-
 &ethmac {
 	status = "okay";
 };
diff --git a/arch/arm/dts/meson-gxl-s905x-libretech-cc.dts b/arch/arm/dts/meson-gxl-s905x-libretech-cc.dts
index 5ae7bb6209..82bfabfbd3 100644
--- a/arch/arm/dts/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm/dts/meson-gxl-s905x-libretech-cc.dts
@@ -135,7 +135,7 @@
 
 	sound {
 		compatible = "amlogic,gx-sound-card";
-		model = "GXL-LIBRETECH-S905X-CC";
+		model = "LIBRETECH-CC";
 		audio-aux-devs = <&dio2133>;
 		audio-widgets = "Line", "Lineout";
 		audio-routing = "AU2 INL", "ACODEC LOLN",
diff --git a/arch/arm/dts/meson-gxm-khadas-vim2.dts b/arch/arm/dts/meson-gxm-khadas-vim2.dts
index bff8ec2c1c..18a4b7a6c5 100644
--- a/arch/arm/dts/meson-gxm-khadas-vim2.dts
+++ b/arch/arm/dts/meson-gxm-khadas-vim2.dts
@@ -7,9 +7,9 @@
 
 /dts-v1/;
 
-#include <dt-bindings/input/input.h>
-
 #include "meson-gxm.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/meson-aiu.h>
 
 / {
 	compatible = "khadas,vim2", "amlogic,s912", "amlogic,meson-gxm";
@@ -81,10 +81,10 @@
 		};
 	};
 
-	pwmleds {
+	led-controller {
 		compatible = "pwm-leds";
 
-		power {
+		led-1 {
 			label = "vim:red:power";
 			pwms = <&pwm_AO_ab 1 7812500 0>;
 			max-brightness = <255>;
@@ -145,6 +145,45 @@
 		clock-frequency = <32768>;
 		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
 	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "KHADAS-VIM2";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&aiu {
+	status = "okay";
 };
 
 &cec_AO {
@@ -154,7 +193,6 @@
 	hdmi-phandle = <&hdmi_tx>;
 };
 
-
 &cpu_cooling_maps {
 	map0 {
 		cooling-device = <&gpio_fan THERMAL_NO_LIMIT 1>;
@@ -194,7 +232,7 @@
 		reg = <0>;
 
 		reset-assert-us = <10000>;
-		reset-deassert-us = <30000>;
+		reset-deassert-us = <80000>;
 		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
 
 		interrupt-parent = <&gpio_intc>;
@@ -228,8 +266,7 @@
 	pinctrl-names = "default";
 
 	rtc: rtc@51 {
-		/* has to be enabled manually when a battery is connected: */
-		status = "disabled";
+		status = "okay";
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
@@ -341,7 +378,7 @@
 		#size-cells = <1>;
 		compatible = "winbond,w25q16", "jedec,spi-nor";
 		reg = <0>;
-		spi-max-frequency = <3000000>;
+		spi-max-frequency = <104000000>;
 	};
 };
 
diff --git a/arch/arm/dts/meson-gxm.dtsi b/arch/arm/dts/meson-gxm.dtsi
index fe41451122..411cc312fc 100644
--- a/arch/arm/dts/meson-gxm.dtsi
+++ b/arch/arm/dts/meson-gxm.dtsi
@@ -42,11 +42,28 @@
 			};
 		};
 
+		cpu0: cpu@0 {
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu1: cpu@1 {
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu2: cpu@2 {
+			capacity-dmips-mhz = <1024>;
+		};
+
+		cpu3: cpu@3 {
+			capacity-dmips-mhz = <1024>;
+		};
+
 		cpu4: cpu@100 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&l2>;
 			clocks = <&scpi_dvfs 1>;
 			#cooling-cells = <2>;
@@ -57,6 +74,7 @@
 			compatible = "arm,cortex-a53";
 			reg = <0x0 0x101>;
 			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&l2>;
 			clocks = <&scpi_dvfs 1>;
 			#cooling-cells = <2>;
@@ -67,6 +85,7 @@
 			compatible = "arm,cortex-a53";
 			reg = <0x0 0x102>;
 			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&l2>;
 			clocks = <&scpi_dvfs 1>;
 			#cooling-cells = <2>;
@@ -77,6 +96,7 @@
 			compatible = "arm,cortex-a53";
 			reg = <0x0 0x103>;
 			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
 			next-level-cache = <&l2>;
 			clocks = <&scpi_dvfs 1>;
 			#cooling-cells = <2>;
diff --git a/arch/arm/dts/meson-khadas-vim3.dtsi b/arch/arm/dts/meson-khadas-vim3.dtsi
index 7b46555ac5..877e3b9892 100644
--- a/arch/arm/dts/meson-khadas-vim3.dtsi
+++ b/arch/arm/dts/meson-khadas-vim3.dtsi
@@ -6,6 +6,7 @@
  */
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/gpio/meson-g12a-gpio.h>
 #include <dt-bindings/sound/meson-g12a-tohdmitx.h>
 
@@ -13,6 +14,8 @@
 	aliases {
 		serial0 = &uart_AO;
 		ethernet0 = &ethmac;
+		rtc0 = &rtc;
+		rtc1 = &vrtc;
 	};
 
 	chosen {
@@ -40,14 +43,16 @@
 	leds {
 		compatible = "gpio-leds";
 
-		led-white {
-			label = "vim3:white:sys";
+		white {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_STATUS;
 			gpios = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		led-red {
-			label = "vim3:red";
+		red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
 			gpios = <&gpio_expander 5 GPIO_ACTIVE_HIGH>;
 		};
 	};
@@ -165,7 +170,7 @@
 
 	sound {
 		compatible = "amlogic,axg-sound-card";
-		model = "G12B-KHADAS-VIM3";
+		model = "KHADAS-VIM3";
 		audio-aux-devs = <&tdmout_a>;
 		audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
 				"TDMOUT_A IN 1", "FRDDR_B OUT 0",
@@ -278,12 +283,12 @@
 };
 
 &ethmac {
-        pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-        pinctrl-names = "default";
-        status = "okay";
-        phy-mode = "rgmii";
-        phy-handle = <&external_phy>;
-        amlogic,tx-delay-ns = <2>;
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
 };
 
 &frddr_a {
@@ -330,7 +335,7 @@
 		#gpio-cells = <2>;
 	};
 
-	rtc@51 {
+	rtc: rtc@51 {
 		compatible = "haoyu,hym8563";
 		reg = <0x51>;
 		#clock-cells = <0>;
@@ -349,9 +354,9 @@
 };
 
 &pwm_ef {
-        status = "okay";
-        pinctrl-0 = <&pwm_e_pins>;
-        pinctrl-names = "default";
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
 };
 
 &saradc {
@@ -445,7 +450,6 @@
 	};
 };
 
-
 &tdmif_a {
 	status = "okay";
 };
diff --git a/arch/arm/dts/meson-sm1-khadas-vim3l.dts b/arch/arm/dts/meson-sm1-khadas-vim3l.dts
index 4b517ca720..06de0b1ce7 100644
--- a/arch/arm/dts/meson-sm1-khadas-vim3l.dts
+++ b/arch/arm/dts/meson-sm1-khadas-vim3l.dts
@@ -89,13 +89,12 @@
 	status = "okay";
 };
 
-&sd_emmc_a {
-	sd-uhs-sdr50;
-};
-
 &usb {
 	phys = <&usb2_phy0>, <&usb2_phy1>;
 	phy-names = "usb2-phy0", "usb2-phy1";
 };
  */
 
+&sd_emmc_a {
+	sd-uhs-sdr50;
+};
diff --git a/arch/arm/dts/meson-sm1-odroid-c4.dts b/arch/arm/dts/meson-sm1-odroid-c4.dts
index cf5a98f0e4..b2a4e823c1 100644
--- a/arch/arm/dts/meson-sm1-odroid-c4.dts
+++ b/arch/arm/dts/meson-sm1-odroid-c4.dts
@@ -5,34 +5,12 @@
 
 /dts-v1/;
 
-#include "meson-sm1.dtsi"
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+#include "meson-sm1-odroid.dtsi"
 
 / {
 	compatible = "hardkernel,odroid-c4", "amlogic,sm1";
 	model = "Hardkernel ODROID-C4";
 
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -45,96 +23,6 @@
 		};
 	};
 
-	tflash_vdd: regulator-tflash_vdd {
-		compatible = "regulator-fixed";
-
-		regulator-name = "TFLASH_VDD";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	tf_io: gpio-regulator-tf_io {
-		compatible = "regulator-gpio";
-
-		regulator-name = "TF_IO";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
-		gpios-states = <0>;
-
-		states = <3300000 0>,
-			 <1800000 1>;
-	};
-
-	flash_1v8: regulator-flash_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "FLASH_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	main_12v: regulator-main_12v {
-		compatible = "regulator-fixed";
-		regulator-name = "12V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-always-on;
-	};
-
-	vcc_5v: regulator-vcc_5v {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		vin-supply = <&main_12v>;
-	};
-
-	vcc_1v8: regulator-vcc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vcc_3v3>;
-		regulator-always-on;
-	};
-
-	vcc_3v3: regulator-vcc_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-		/* FIXME: actually controlled by VDDCPU_B_EN */
-	};
-
-	vddcpu: regulator-vddcpu {
-		/*
-		 * MP8756GD Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU";
-		regulator-min-microvolt = <721000>;
-		regulator-max-microvolt = <1022000>;
-
-		vin-supply = <&main_12v>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
 	hub_5v: regulator-hub_5v {
 		compatible = "regulator-fixed";
 		regulator-name = "HUB_5V";
@@ -147,215 +35,12 @@
 		enable-active-high;
 	};
 
-	usb_pwr_en: regulator-usb_pwr_en {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-
-		/* Connected to the microUSB port power enable */
-		gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vddao_1v8: regulator-vddao_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&main_12v>;
-		regulator-always-on;
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
 	sound {
-		compatible = "amlogic,axg-sound-card";
-		model = "SM1-ODROID-C4";
-		audio-aux-devs = <&tdmout_b>;
-		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
-				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
-				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
-				"TDM_B Playback", "TDMOUT_B OUT";
-
-		assigned-clocks = <&clkc CLKID_MPLL2>,
-				  <&clkc CLKID_MPLL0>,
-				  <&clkc CLKID_MPLL1>;
-		assigned-clock-parents = <0>, <0>, <0>;
-		assigned-clock-rates = <294912000>,
-				       <270950400>,
-				       <393216000>;
-		status = "okay";
-
-		dai-link-0 {
-			sound-dai = <&frddr_a>;
-		};
-
-		dai-link-1 {
-			sound-dai = <&frddr_b>;
-		};
-
-		dai-link-2 {
-			sound-dai = <&frddr_c>;
-		};
-
-		/* 8ch hdmi interface */
-		dai-link-3 {
-			sound-dai = <&tdmif_b>;
-			dai-format = "i2s";
-			dai-tdm-slot-tx-mask-0 = <1 1>;
-			dai-tdm-slot-tx-mask-1 = <1 1>;
-			dai-tdm-slot-tx-mask-2 = <1 1>;
-			dai-tdm-slot-tx-mask-3 = <1 1>;
-			mclk-fs = <256>;
-
-			codec {
-				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
-			};
-		};
-
-		/* hdmi glue */
-		dai-link-4 {
-			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
-
-			codec {
-				sound-dai = <&hdmi_tx>;
-			};
-		};
-	};
-};
-
-&arb {
-	status = "okay";
-};
-
-&clkc_audio {
-	status = "okay";
-};
-
-&cpu0 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU1_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu2 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU2_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu3 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU3_CLK>;
-	clock-latency = <50000>;
-};
-
-&ext_mdio {
-	external_phy: ethernet-phy@0 {
-		/* Realtek RTL8211F (0x001cc916) */
-		reg = <0>;
-		max-speed = <1000>;
-
-		interrupt-parent = <&gpio_intc>;
-		/* MAC_INTR on GPIOZ_14 */
-		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+		model = "ODROID-C4";
 	};
 };
 
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii";
-	phy-handle = <&external_phy>;
-	amlogic,tx-delay-ns = <2>;
-};
-
-&frddr_a {
-	status = "okay";
-};
-
-&frddr_b {
-	status = "okay";
-};
-
-&frddr_c {
-	status = "okay";
-};
-
 &gpio {
-	gpio-line-names =
-		/* GPIOZ */
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "", "", "",
-		/* GPIOH */
-		"", "", "", "", "",
-		"PIN_36", /* GPIOH_5 */
-		"PIN_26", /* GPIOH_6 */
-		"PIN_32", /* GPIOH_7 */
-		"",
-		/* BOOT */
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "", "", "",
-		/* GPIOC */
-		"", "", "", "", "", "", "", "",
-		/* GPIOA */
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "",
-		"PIN_27", /* GPIOA_14 */
-		"PIN_28", /* GPIOA_15 */
-		/* GPIOX */
-		"PIN_16", /* GPIOX_0 */
-		"PIN_18", /* GPIOX_1 */
-		"PIN_22", /* GPIOX_2 */
-		"PIN_11", /* GPIOX_3 */
-		"PIN_13", /* GPIOX_4 */
-		"PIN_7",  /* GPIOX_5 */
-		"PIN_33", /* GPIOX_6 */
-		"PIN_15", /* GPIOX_7 */
-		"PIN_19", /* GPIOX_8 */
-		"PIN_21", /* GPIOX_9 */
-		"PIN_24", /* GPIOX_10 */
-		"PIN_23", /* GPIOX_11 */
-		"PIN_8",  /* GPIOX_12 */
-		"PIN_10", /* GPIOX_13 */
-		"PIN_29", /* GPIOX_14 */
-		"PIN_31", /* GPIOX_15 */
-		"PIN_12", /* GPIOX_16 */
-		"PIN_3",  /* GPIOX_17 */
-		"PIN_5",  /* GPIOX_18 */
-		"PIN_35"; /* GPIOX_19 */
-
 	/*
 	 * WARNING: The USB Hub on the Odroid-C4 needs a reset signal
 	 * to be turned high in order to be detected by the USB Controller
@@ -370,120 +55,10 @@
 	};
 };
 
-&gpio_ao {
-	gpio-line-names =
-		/* GPIOAO */
-		"", "", "", "",
-		"PIN_47", /* GPIOAO_4 */
-		"", "",
-		"PIN_45", /* GPIOAO_7 */
-		"PIN_46", /* GPIOAO_8 */
-		"PIN_44", /* GPIOAO_9 */
-		"PIN_42", /* GPIOAO_10 */
-		"",
-		/* GPIOE */
-		"", "", "";
-};
-
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&vcc_5v>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
 &ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
 	linux,rc-map-name = "rc-odroid";
 };
 
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&saradc {
-	status = "okay";
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <200000000>;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	disable-wp;
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&tflash_vdd>;
-	vqmmc-supply = <&tf_io>;
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	max-frequency = <200000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&flash_1v8>;
-};
-
-&tdmif_b {
-	status = "okay";
-};
-
-&tdmout_b {
-	status = "okay";
-};
-
-&tohdmitx {
-	status = "okay";
-};
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-	vbus-supply = <&usb_pwr_en>;
-};
-
-&usb2_phy0 {
-	phy-supply = <&vcc_5v>;
-};
-
 &usb2_phy1 {
 	/* Enable the hub which is connected to this port */
 	phy-supply = <&hub_5v>;
diff --git a/arch/arm/dts/meson-sm1-odroid-hc4.dts b/arch/arm/dts/meson-sm1-odroid-hc4.dts
new file mode 100644
index 0000000000..bf15700c4b
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-odroid-hc4.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Dongjin Kim <tobetter@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-odroid.dtsi"
+
+/ {
+	compatible = "hardkernel,odroid-hc4", "amlogic,sm1";
+	model = "Hardkernel ODROID-HC4";
+
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &vrtc;
+	};
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		#cooling-cells = <2>;
+		cooling-min-state = <0>;
+		cooling-max-state = <3>;
+		cooling-levels = <0 120 170 220>;
+		pwms = <&pwm_cd 1 40000 0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			panic-indicator;
+		};
+
+		led-red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	sound {
+		model = "ODROID-HC4";
+	};
+};
+
+&cpu_thermal {
+	cooling-maps {
+		map {
+			trip = <&cpu_passive>;
+			cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&ir {
+	linux,rc-map-name = "rc-odroid";
+};
+
+&i2c2 {
+	status = "okay";
+	pinctrl-0 = <&i2c2_sda_x_pins>, <&i2c2_sck_x_pins>;
+	pinctrl-names = "default";
+
+	rtc: rtc@51 {
+		status = "okay";
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		wakeup-source;
+	};
+};
+
+&pcie {
+	status = "okay";
+	reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+};
+
+&pwm_cd {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm_d_x6_pins>;
+};
+
+&sd_emmc_c {
+	status = "disabled";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
diff --git a/arch/arm/dts/meson-sm1-odroid.dtsi b/arch/arm/dts/meson-sm1-odroid.dtsi
new file mode 100644
index 0000000000..d14716b3d0
--- /dev/null
+++ b/arch/arm/dts/meson-sm1-odroid.dtsi
@@ -0,0 +1,442 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Dongjin Kim <tobetter@gmail.com>
+ */
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0>,
+			 <1800000 1>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&main_12v>;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	vddcpu: regulator-vddcpu {
+		/*
+		 * MP8756GD Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		vin-supply = <&main_12v>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the microUSB port power enable */
+		gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&gpio {
+	gpio-line-names =
+		/* GPIOZ */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		/* GPIOH */
+		"", "", "", "", "",
+		"PIN_36", /* GPIOH_5 */
+		"PIN_26", /* GPIOH_6 */
+		"PIN_32", /* GPIOH_7 */
+		"",
+		/* BOOT */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		/* GPIOC */
+		"", "", "", "", "", "", "", "",
+		/* GPIOA */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "",
+		"PIN_27", /* GPIOA_14 */
+		"PIN_28", /* GPIOA_15 */
+		/* GPIOX */
+		"PIN_16", /* GPIOX_0 */
+		"PIN_18", /* GPIOX_1 */
+		"PIN_22", /* GPIOX_2 */
+		"PIN_11", /* GPIOX_3 */
+		"PIN_13", /* GPIOX_4 */
+		"PIN_7",  /* GPIOX_5 */
+		"PIN_33", /* GPIOX_6 */
+		"PIN_15", /* GPIOX_7 */
+		"PIN_19", /* GPIOX_8 */
+		"PIN_21", /* GPIOX_9 */
+		"PIN_24", /* GPIOX_10 */
+		"PIN_23", /* GPIOX_11 */
+		"PIN_8",  /* GPIOX_12 */
+		"PIN_10", /* GPIOX_13 */
+		"PIN_29", /* GPIOX_14 */
+		"PIN_31", /* GPIOX_15 */
+		"PIN_12", /* GPIOX_16 */
+		"PIN_3",  /* GPIOX_17 */
+		"PIN_5",  /* GPIOX_18 */
+		"PIN_35"; /* GPIOX_19 */
+};
+
+&gpio_ao {
+	gpio-line-names =
+		/* GPIOAO */
+		"", "", "", "",
+		"PIN_47", /* GPIOAO_4 */
+		"", "",
+		"PIN_45", /* GPIOAO_7 */
+		"PIN_46", /* GPIOAO_8 */
+		"PIN_44", /* GPIOAO_9 */
+		"PIN_42", /* GPIOAO_10 */
+		"",
+		/* GPIOE */
+		"", "", "";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <200000000>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};
+
diff --git a/arch/arm/dts/meson-sm1-sei610.dts b/arch/arm/dts/meson-sm1-sei610.dts
index 5ab139a34c..2194a77897 100644
--- a/arch/arm/dts/meson-sm1-sei610.dts
+++ b/arch/arm/dts/meson-sm1-sei610.dts
@@ -101,20 +101,20 @@
 		};
 	};
 
-	leds {
+	led-controller-1 {
 		compatible = "gpio-leds";
 
-		led-bluetooth {
+		led-1 {
 			label = "sei610:blue:bt";
 			gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
 			default-state = "off";
 		};
 	};
 
-	pwmleds {
+	led-controller-2 {
 		compatible = "pwm-leds";
 
-		power {
+		led-2 {
 			label = "sei610:red:power";
 			pwms = <&pwm_AO_ab 0 30518 0>;
 			max-brightness = <255>;
@@ -220,7 +220,7 @@
 
 	sound {
 		compatible = "amlogic,axg-sound-card";
-		model = "SM1-SEI610";
+		model = "SEI610";
 		audio-aux-devs = <&tdmout_a>, <&tdmout_b>,
 				 <&tdmin_a>, <&tdmin_b>;
 		audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0",
diff --git a/arch/arm/dts/meson-sm1.dtsi b/arch/arm/dts/meson-sm1.dtsi
index 71317f5aad..c309517aba 100644
--- a/arch/arm/dts/meson-sm1.dtsi
+++ b/arch/arm/dts/meson-sm1.dtsi
@@ -130,7 +130,7 @@
 			opp-microvolt = <790000>;
 		};
 
-		opp-1512000000 {
+		opp-1500000000 {
 			opp-hz = /bits/ 64 <1500000000>;
 			opp-microvolt = <800000>;
 		};
diff --git a/include/dt-bindings/clock/axg-clkc.h b/include/dt-bindings/clock/axg-clkc.h
index fd1f938c38..93752ea107 100644
--- a/include/dt-bindings/clock/axg-clkc.h
+++ b/include/dt-bindings/clock/axg-clkc.h
@@ -70,7 +70,31 @@
 #define CLKID_HIFI_PLL				69
 #define CLKID_PCIE_CML_EN0			79
 #define CLKID_PCIE_CML_EN1			80
-#define CLKID_MIPI_ENABLE			81
 #define CLKID_GEN_CLK				84
+#define CLKID_VPU_0_SEL				92
+#define CLKID_VPU_0				93
+#define CLKID_VPU_1_SEL				95
+#define CLKID_VPU_1				96
+#define CLKID_VPU				97
+#define CLKID_VAPB_0_SEL			99
+#define CLKID_VAPB_0				100
+#define CLKID_VAPB_1_SEL			102
+#define CLKID_VAPB_1				103
+#define CLKID_VAPB_SEL				104
+#define CLKID_VAPB				105
+#define CLKID_VCLK				106
+#define CLKID_VCLK2				107
+#define CLKID_VCLK_DIV1				122
+#define CLKID_VCLK_DIV2				123
+#define CLKID_VCLK_DIV4				124
+#define CLKID_VCLK_DIV6				125
+#define CLKID_VCLK_DIV12			126
+#define CLKID_VCLK2_DIV1			127
+#define CLKID_VCLK2_DIV2			128
+#define CLKID_VCLK2_DIV4			129
+#define CLKID_VCLK2_DIV6			130
+#define CLKID_VCLK2_DIV12			131
+#define CLKID_CTS_ENCL				133
+#define CLKID_VDIN_MEAS				136
 
 #endif /* __AXG_CLKC_H */
diff --git a/include/dt-bindings/clock/g12a-clkc.h b/include/dt-bindings/clock/g12a-clkc.h
index 40d49940d8..a93b58c5e1 100644
--- a/include/dt-bindings/clock/g12a-clkc.h
+++ b/include/dt-bindings/clock/g12a-clkc.h
@@ -147,5 +147,7 @@
 #define CLKID_SPICC1_SCLK			261
 #define CLKID_NNA_AXI_CLK			264
 #define CLKID_NNA_CORE_CLK			267
+#define CLKID_MIPI_DSI_PXCLK_SEL		269
+#define CLKID_MIPI_DSI_PXCLK			270
 
 #endif /* __G12A_CLKC_H */
