Message ID | 20190314104009.8113-1-paul.kocialkowski@bootlin.com |
---|---|
State | Changes Requested |
Delegated to: | Jagannadha Sutradharudu Teki |
Headers | show |
Series | [U-Boot] arm: sunxi: Add support for the RerVision H3-DVK board | expand |
On Thu, Mar 14, 2019 at 4:10 PM Paul Kocialkowski <paul.kocialkowski@bootlin.com> wrote: > > This is an H3-based board that sticks close to the reference design. > > Supported features: > * UART > * DRAM > * MMC > * eMMC > * Ethernet > * USB host > * USB peripheral > * HDMI Can you add commit details of dts file from Linux sync, I usually prefer this for future reference syncs. > > Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> > --- > arch/arm/dts/Makefile | 3 +- > arch/arm/dts/sun8i-h3-rervision-dvk.dts | 107 ++++++++++++++++++++++++ > configs/rervision_h3_dvk_defconfig | 17 ++++ > 3 files changed, 126 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/dts/sun8i-h3-rervision-dvk.dts > create mode 100644 configs/rervision_h3_dvk_defconfig > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index 2a040b20a539..a64c0fada4cb 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -401,7 +401,8 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \ > sun8i-h3-orangepi-pc.dtb \ > sun8i-h3-orangepi-pc-plus.dtb \ > sun8i-h3-orangepi-plus.dtb \ > - sun8i-h3-orangepi-plus2e.dtb > + sun8i-h3-orangepi-plus2e.dtb \ > + sun8i-h3-rervision-dvk.dtb > dtb-$(CONFIG_MACH_SUN8I_R40) += \ > sun8i-r40-bananapi-m2-ultra.dtb \ > sun8i-v40-bananapi-m2-berry.dtb > diff --git a/arch/arm/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/dts/sun8i-h3-rervision-dvk.dts > new file mode 100644 > index 000000000000..8a4b83a02d9d > --- /dev/null > +++ b/arch/arm/dts/sun8i-h3-rervision-dvk.dts > @@ -0,0 +1,107 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2019 Bootlin > + * Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com> > + */ > + > +/dts-v1/; > +#include "sun8i-h3.dtsi" > +#include "sunxi-common-regulators.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +/ { > + model = "RerVision H3-DVK"; > + compatible = "rervision,h3-dvk", "allwinner,sun8i-h3"; > + > + aliases { > + ethernet0 = &emac; > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + connector { > + compatible = "hdmi-connector"; > + type = "a"; > + > + port { > + hdmi_connector_input: endpoint { > + remote-endpoint = <&hdmi_connector_output>; > + }; > + }; > + }; > +}; > + > +&ehci1 { > + status = "okay"; > +}; > + > +&ehci2 { > + status = "okay"; > +}; > + > +&emac { > + phy-handle = <&int_mii_phy>; > + phy-mode = "mii"; > + allwinner,leds-active-low; > + status = "okay"; > +}; > + > +&hdmi { > + status = "okay"; > +}; > + > +&hdmi_out { > + hdmi_connector_output: endpoint { > + remote-endpoint = <&hdmi_connector_input>; > + }; > +}; > + > +&mmc0 { > + bus-width = <4>; > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > + status = "okay"; > + vmmc-supply = <®_vcc3v3>; > +}; > + > +&mmc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_8bit_pins>; > + vmmc-supply = <®_vcc3v3>; > + bus-width = <8>; > + non-removable; > + cap-mmc-hw-reset; > + status = "okay"; > +}; > + > +&mmc2_8bit_pins { > + drive-strength = <40>; > + bias-pull-up; > +}; > + > +&ohci1 { > + status = "okay"; > +}; > + > +&ohci2 { > + status = "okay"; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pins_a>; > + status = "okay"; > +}; > + > +&usb_otg { > + status = "okay"; > + dr_mode = "peripheral"; > +}; > + > +&usbphy { > + status = "okay"; > +}; > diff --git a/configs/rervision_h3_dvk_defconfig b/configs/rervision_h3_dvk_defconfig > new file mode 100644 > index 000000000000..895a985ccdcd > --- /dev/null > +++ b/configs/rervision_h3_dvk_defconfig > @@ -0,0 +1,17 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_SUNXI=y > +CONFIG_SPL=y > +CONFIG_MACH_SUN8I_H3=y > +CONFIG_DRAM_CLK=408 > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2 > +CONFIG_NR_DRAM_BANKS=1 > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set > +# CONFIG_CMD_FLASH is not set > +# CONFIG_SPL_DOS_PARTITION is not set > +# CONFIG_SPL_EFI_PARTITION is not set > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-rervision-dvk" > +CONFIG_USB_EHCI_HCD=y > +CONFIG_USB_OHCI_HCD=y > +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y > +CONFIG_USB_MUSB_GADGET=y > +CONFIG_FASTBOOT=y Not needed, this can enabled by MUSB_GADET
Hi, Le mardi 09 avril 2019 à 15:56 +0530, Jagan Teki a écrit : > On Thu, Mar 14, 2019 at 4:10 PM Paul Kocialkowski > <paul.kocialkowski@bootlin.com> wrote: > > This is an H3-based board that sticks close to the reference design. > > > > Supported features: > > * UART > > * DRAM > > * MMC > > * eMMC > > * Ethernet > > * USB host > > * USB peripheral > > * HDMI > > Can you add commit details of dts file from Linux sync, I usually > prefer this for future reference syncs. Sure thing, I'll make a new version with the associated linux commit listed. Cheers, Paul > > Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> > > --- > > arch/arm/dts/Makefile | 3 +- > > arch/arm/dts/sun8i-h3-rervision-dvk.dts | 107 ++++++++++++++++++++++++ > > configs/rervision_h3_dvk_defconfig | 17 ++++ > > 3 files changed, 126 insertions(+), 1 deletion(-) > > create mode 100644 arch/arm/dts/sun8i-h3-rervision-dvk.dts > > create mode 100644 configs/rervision_h3_dvk_defconfig > > > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > > index 2a040b20a539..a64c0fada4cb 100644 > > --- a/arch/arm/dts/Makefile > > +++ b/arch/arm/dts/Makefile > > @@ -401,7 +401,8 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \ > > sun8i-h3-orangepi-pc.dtb \ > > sun8i-h3-orangepi-pc-plus.dtb \ > > sun8i-h3-orangepi-plus.dtb \ > > - sun8i-h3-orangepi-plus2e.dtb > > + sun8i-h3-orangepi-plus2e.dtb \ > > + sun8i-h3-rervision-dvk.dtb > > dtb-$(CONFIG_MACH_SUN8I_R40) += \ > > sun8i-r40-bananapi-m2-ultra.dtb \ > > sun8i-v40-bananapi-m2-berry.dtb > > diff --git a/arch/arm/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/dts/sun8i-h3-rervision-dvk.dts > > new file mode 100644 > > index 000000000000..8a4b83a02d9d > > --- /dev/null > > +++ b/arch/arm/dts/sun8i-h3-rervision-dvk.dts > > @@ -0,0 +1,107 @@ > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > > +/* > > + * Copyright (C) 2019 Bootlin > > + * Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com> > > + */ > > + > > +/dts-v1/; > > +#include "sun8i-h3.dtsi" > > +#include "sunxi-common-regulators.dtsi" > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/input.h> > > + > > +/ { > > + model = "RerVision H3-DVK"; > > + compatible = "rervision,h3-dvk", "allwinner,sun8i-h3"; > > + > > + aliases { > > + ethernet0 = &emac; > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > + > > + connector { > > + compatible = "hdmi-connector"; > > + type = "a"; > > + > > + port { > > + hdmi_connector_input: endpoint { > > + remote-endpoint = <&hdmi_connector_output>; > > + }; > > + }; > > + }; > > +}; > > + > > +&ehci1 { > > + status = "okay"; > > +}; > > + > > +&ehci2 { > > + status = "okay"; > > +}; > > + > > +&emac { > > + phy-handle = <&int_mii_phy>; > > + phy-mode = "mii"; > > + allwinner,leds-active-low; > > + status = "okay"; > > +}; > > + > > +&hdmi { > > + status = "okay"; > > +}; > > + > > +&hdmi_out { > > + hdmi_connector_output: endpoint { > > + remote-endpoint = <&hdmi_connector_input>; > > + }; > > +}; > > + > > +&mmc0 { > > + bus-width = <4>; > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ > > + status = "okay"; > > + vmmc-supply = <®_vcc3v3>; > > +}; > > + > > +&mmc2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&mmc2_8bit_pins>; > > + vmmc-supply = <®_vcc3v3>; > > + bus-width = <8>; > > + non-removable; > > + cap-mmc-hw-reset; > > + status = "okay"; > > +}; > > + > > +&mmc2_8bit_pins { > > + drive-strength = <40>; > > + bias-pull-up; > > +}; > > + > > +&ohci1 { > > + status = "okay"; > > +}; > > + > > +&ohci2 { > > + status = "okay"; > > +}; > > + > > +&uart0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart0_pins_a>; > > + status = "okay"; > > +}; > > + > > +&usb_otg { > > + status = "okay"; > > + dr_mode = "peripheral"; > > +}; > > + > > +&usbphy { > > + status = "okay"; > > +}; > > diff --git a/configs/rervision_h3_dvk_defconfig b/configs/rervision_h3_dvk_defconfig > > new file mode 100644 > > index 000000000000..895a985ccdcd > > --- /dev/null > > +++ b/configs/rervision_h3_dvk_defconfig > > @@ -0,0 +1,17 @@ > > +CONFIG_ARM=y > > +CONFIG_ARCH_SUNXI=y > > +CONFIG_SPL=y > > +CONFIG_MACH_SUN8I_H3=y > > +CONFIG_DRAM_CLK=408 > > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2 > > +CONFIG_NR_DRAM_BANKS=1 > > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set > > +# CONFIG_CMD_FLASH is not set > > +# CONFIG_SPL_DOS_PARTITION is not set > > +# CONFIG_SPL_EFI_PARTITION is not set > > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-rervision-dvk" > > +CONFIG_USB_EHCI_HCD=y > > +CONFIG_USB_OHCI_HCD=y > > +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y > > +CONFIG_USB_MUSB_GADGET=y > > +CONFIG_FASTBOOT=y > > Not needed, this can enabled by MUSB_GADET
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 2a040b20a539..a64c0fada4cb 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -401,7 +401,8 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \ sun8i-h3-orangepi-pc.dtb \ sun8i-h3-orangepi-pc-plus.dtb \ sun8i-h3-orangepi-plus.dtb \ - sun8i-h3-orangepi-plus2e.dtb + sun8i-h3-orangepi-plus2e.dtb \ + sun8i-h3-rervision-dvk.dtb dtb-$(CONFIG_MACH_SUN8I_R40) += \ sun8i-r40-bananapi-m2-ultra.dtb \ sun8i-v40-bananapi-m2-berry.dtb diff --git a/arch/arm/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/dts/sun8i-h3-rervision-dvk.dts new file mode 100644 index 000000000000..8a4b83a02d9d --- /dev/null +++ b/arch/arm/dts/sun8i-h3-rervision-dvk.dts @@ -0,0 +1,107 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Bootlin + * Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com> + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "RerVision H3-DVK"; + compatible = "rervision,h3-dvk", "allwinner,sun8i-h3"; + + aliases { + ethernet0 = &emac; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_input: endpoint { + remote-endpoint = <&hdmi_connector_output>; + }; + }; + }; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_connector_output: endpoint { + remote-endpoint = <&hdmi_connector_input>; + }; +}; + +&mmc0 { + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + status = "okay"; + vmmc-supply = <®_vcc3v3>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_8bit_pins>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&mmc2_8bit_pins { + drive-strength = <40>; + bias-pull-up; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usb_otg { + status = "okay"; + dr_mode = "peripheral"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/configs/rervision_h3_dvk_defconfig b/configs/rervision_h3_dvk_defconfig new file mode 100644 index 000000000000..895a985ccdcd --- /dev/null +++ b/configs/rervision_h3_dvk_defconfig @@ -0,0 +1,17 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_SPL=y +CONFIG_MACH_SUN8I_H3=y +CONFIG_DRAM_CLK=408 +CONFIG_MMC_SUNXI_SLOT_EXTRA=2 +CONFIG_NR_DRAM_BANKS=1 +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_SPL_DOS_PARTITION is not set +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-rervision-dvk" +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y +CONFIG_USB_MUSB_GADGET=y +CONFIG_FASTBOOT=y
This is an H3-based board that sticks close to the reference design. Supported features: * UART * DRAM * MMC * eMMC * Ethernet * USB host * USB peripheral * HDMI Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> --- arch/arm/dts/Makefile | 3 +- arch/arm/dts/sun8i-h3-rervision-dvk.dts | 107 ++++++++++++++++++++++++ configs/rervision_h3_dvk_defconfig | 17 ++++ 3 files changed, 126 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/sun8i-h3-rervision-dvk.dts create mode 100644 configs/rervision_h3_dvk_defconfig