Message ID | 20181017050932.11138-2-anarsoul@gmail.com |
---|---|
State | Superseded |
Delegated to: | Jagannadha Sutradharudu Teki |
Headers | show |
Series | Add support for Pinebook | expand |
On 10/17/18 6:09 AM, Vasily Khoruzhick wrote: > A64 supports automatic delay calibration and Linux driver uses it > instead of hardcoded delays. Add support for it to u-boot driver. > > Fixes eMMC instability on Pinebook > > Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> > --- > arch/arm/include/asm/arch-sunxi/mmc.h | 6 +++++- > drivers/mmc/sunxi_mmc.c | 21 ++++++++++++++++++++- > 2 files changed, 25 insertions(+), 2 deletions(-) > > diff --git a/arch/arm/include/asm/arch-sunxi/mmc.h b/arch/arm/include/asm/arch-sunxi/mmc.h > index d98c53faaa..f2deafddd2 100644 > --- a/arch/arm/include/asm/arch-sunxi/mmc.h > +++ b/arch/arm/include/asm/arch-sunxi/mmc.h > @@ -46,7 +46,9 @@ struct sunxi_mmc { > u32 cbda; /* 0x94 */ > u32 res2[26]; > #if defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6) > - u32 res3[64]; > + u32 res3[17]; > + u32 samp_dl; > + u32 res4[46]; > #endif > u32 fifo; /* 0x100 / 0x200 FIFO access address */ > }; > @@ -130,5 +132,7 @@ struct sunxi_mmc { > #define SUNXI_MMC_COMMON_CLK_GATE (1 << 16) > #define SUNXI_MMC_COMMON_RESET (1 << 18) > > +#define SUNXI_MMC_CAL_DL_SW_EN (0x1 << 7) > + > struct mmc *sunxi_mmc_init(int sdc_no); > #endif /* _SUNXI_MMC_H */ > diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c > index 39f15eb423..9e08ad59c6 100644 > --- a/drivers/mmc/sunxi_mmc.c > +++ b/drivers/mmc/sunxi_mmc.c > @@ -99,11 +99,16 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz) > { > unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly; > bool new_mode = false; > + bool calibrate = false; > u32 val = 0; > > if (IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE) && (priv->mmc_no == 2)) > new_mode = true; > > +#ifdef CONFIG_MACH_SUN50I According to the Linux driver this applies to the H6 eMMC controller as well. So can you please add CONFIG_MACH_SUN50I_H6 here as well? Same below, of course. Rest looks fine to me. Cheers, Andre. > + calibrate = true; > +#endif > + > /* > * The MMC clock has an extra /2 post-divider when operating in the new > * mode. > @@ -174,7 +179,11 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz) > val = CCM_MMC_CTRL_MODE_SEL_NEW; > setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW); > #endif > - } else { > + } else if (!calibrate) { > + /* > + * Use hardcoded delay values if controller doesn't support > + * calibration > + */ > val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) | > CCM_MMC_CTRL_SCLK_DLY(sclk_dly); > } > @@ -228,6 +237,16 @@ static int mmc_config_clock(struct sunxi_mmc_priv *priv, struct mmc *mmc) > rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK; > writel(rval, &priv->reg->clkcr); > > +#ifdef CONFIG_MACH_SUN50I > + /* A64 supports calibration of delays on MMC controller and we > + * have to set delay of zero before starting calibration. > + * Allwinner BSP driver sets a delay only in the case of > + * using HS400 which is not supported by mainline U-Boot or > + * Linux at the moment > + */ > + writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl); > +#endif > + > /* Re-enable Clock */ > rval |= SUNXI_MMC_CLK_ENABLE; > writel(rval, &priv->reg->clkcr); >
diff --git a/arch/arm/include/asm/arch-sunxi/mmc.h b/arch/arm/include/asm/arch-sunxi/mmc.h index d98c53faaa..f2deafddd2 100644 --- a/arch/arm/include/asm/arch-sunxi/mmc.h +++ b/arch/arm/include/asm/arch-sunxi/mmc.h @@ -46,7 +46,9 @@ struct sunxi_mmc { u32 cbda; /* 0x94 */ u32 res2[26]; #if defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6) - u32 res3[64]; + u32 res3[17]; + u32 samp_dl; + u32 res4[46]; #endif u32 fifo; /* 0x100 / 0x200 FIFO access address */ }; @@ -130,5 +132,7 @@ struct sunxi_mmc { #define SUNXI_MMC_COMMON_CLK_GATE (1 << 16) #define SUNXI_MMC_COMMON_RESET (1 << 18) +#define SUNXI_MMC_CAL_DL_SW_EN (0x1 << 7) + struct mmc *sunxi_mmc_init(int sdc_no); #endif /* _SUNXI_MMC_H */ diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c index 39f15eb423..9e08ad59c6 100644 --- a/drivers/mmc/sunxi_mmc.c +++ b/drivers/mmc/sunxi_mmc.c @@ -99,11 +99,16 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz) { unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly; bool new_mode = false; + bool calibrate = false; u32 val = 0; if (IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE) && (priv->mmc_no == 2)) new_mode = true; +#ifdef CONFIG_MACH_SUN50I + calibrate = true; +#endif + /* * The MMC clock has an extra /2 post-divider when operating in the new * mode. @@ -174,7 +179,11 @@ static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz) val = CCM_MMC_CTRL_MODE_SEL_NEW; setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW); #endif - } else { + } else if (!calibrate) { + /* + * Use hardcoded delay values if controller doesn't support + * calibration + */ val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) | CCM_MMC_CTRL_SCLK_DLY(sclk_dly); } @@ -228,6 +237,16 @@ static int mmc_config_clock(struct sunxi_mmc_priv *priv, struct mmc *mmc) rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK; writel(rval, &priv->reg->clkcr); +#ifdef CONFIG_MACH_SUN50I + /* A64 supports calibration of delays on MMC controller and we + * have to set delay of zero before starting calibration. + * Allwinner BSP driver sets a delay only in the case of + * using HS400 which is not supported by mainline U-Boot or + * Linux at the moment + */ + writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl); +#endif + /* Re-enable Clock */ rval |= SUNXI_MMC_CLK_ENABLE; writel(rval, &priv->reg->clkcr);
A64 supports automatic delay calibration and Linux driver uses it instead of hardcoded delays. Add support for it to u-boot driver. Fixes eMMC instability on Pinebook Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> --- arch/arm/include/asm/arch-sunxi/mmc.h | 6 +++++- drivers/mmc/sunxi_mmc.c | 21 ++++++++++++++++++++- 2 files changed, 25 insertions(+), 2 deletions(-)