@@ -1019,7 +1019,7 @@ The following options need to be configured:
CONFIG_RTC_DS164x - use Dallas DS164x RTC
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
- CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
+ CONFIG_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
CONFIG_SYS_RV3029_TCR - enable trickle charger on
RV3029 RTC.
@@ -150,11 +150,11 @@ int rtc_set (struct rtc_time *tmp)
* SQW/INTB* pin and program it for 32,768 Hz output. Note that
* according to the datasheet, turning on the square wave output
* increases the current drain on the backup battery from about
- * 600 nA to 2uA. Define CONFIG_SYS_RTC_DS1337_NOOSC if you wish to turn
+ * 600 nA to 2uA. Define CONFIG_RTC_DS1337_NOOSC if you wish to turn
* off the OSC output.
*/
-#ifdef CONFIG_SYS_RTC_DS1337_NOOSC
+#ifdef CONFIG_RTC_DS1337_NOOSC
#define RTC_DS1337_RESET_VAL \
(RTC_CTL_BIT_INTCN | RTC_CTL_BIT_RS1 | RTC_CTL_BIT_RS2)
#else
@@ -162,16 +162,16 @@ int rtc_set (struct rtc_time *tmp)
#endif
void rtc_reset (void)
{
-#ifdef CONFIG_SYS_RTC_DS1337
+#ifdef CONFIG_RTC_DS1337
rtc_write (RTC_CTL_REG_ADDR, RTC_DS1337_RESET_VAL);
-#elif defined CONFIG_SYS_RTC_DS1388
+#elif defined CONFIG_RTC_DS1388
rtc_write(RTC_CTL_REG_ADDR, 0x0); /* hw default */
#endif
-#ifdef CONFIG_SYS_DS1339_TCR_VAL
- rtc_write (RTC_TC_REG_ADDR, CONFIG_SYS_DS1339_TCR_VAL);
+#ifdef CONFIG_RTC_DS1339_TCR_VAL
+ rtc_write (RTC_TC_REG_ADDR, CONFIG_RTC_DS1339_TCR_VAL);
#endif
-#ifdef CONFIG_SYS_DS1388_TCR_VAL
- rtc_write(RTC_TC_REG_ADDR, CONFIG_SYS_DS1388_TCR_VAL);
+#ifdef CONFIG_RTC_DS1388_TCR_VAL
+ rtc_write(RTC_TC_REG_ADDR, CONFIG_RTC_DS1388_TCR_VAL);
#endif
}
@@ -311,7 +311,7 @@
#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_RTC_DS1337_NOOSC
+#define CONFIG_RTC_DS1337_NOOSC
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
#define CONFIG_SYS_I2C_NCT72_ADDR 0x4C
@@ -29,7 +29,7 @@
#define CONFIG_SYS_RTC_BUS_NUM 2
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/* Turn off RTC square-wave output to save battery */
-#define CONFIG_SYS_RTC_DS1337_NOOSC
+#define CONFIG_RTC_DS1337_NOOSC
/* LED */
@@ -2269,9 +2269,12 @@ CONFIG_RSK7264
CONFIG_RSK7269
CONFIG_RTC_DS1307
CONFIG_RTC_DS1337
+CONFIG_RTC_DS1337_NOOSC
CONFIG_RTC_DS1338
+CONFIG_RTC_DS1339_TCR_VAL
CONFIG_RTC_DS1374
CONFIG_RTC_DS1388
+CONFIG_RTC_DS1388_TCR_VAL
CONFIG_RTC_DS1556
CONFIG_RTC_DS174x
CONFIG_RTC_DS3231
@@ -3383,8 +3386,6 @@ CONFIG_SYS_DRAMSZ1
CONFIG_SYS_DRAM_BASE
CONFIG_SYS_DRAM_SIZE
CONFIG_SYS_DRAM_TEST
-CONFIG_SYS_DS1339_TCR_VAL
-CONFIG_SYS_DS1388_TCR_VAL
CONFIG_SYS_DSPIC_TEST_ADDR
CONFIG_SYS_DSPIC_TEST_MASK
CONFIG_SYS_DSPI_CS0
@@ -5515,9 +5516,6 @@ CONFIG_SYS_RSTC_RMR_VAL
CONFIG_SYS_RTCSC
CONFIG_SYS_RTC_BUS_NUM
CONFIG_SYS_RTC_CNT
-CONFIG_SYS_RTC_DS1337
-CONFIG_SYS_RTC_DS1337_NOOSC
-CONFIG_SYS_RTC_DS1388
CONFIG_SYS_RTC_OSCILLATOR
CONFIG_SYS_RTC_PL031_BASE
CONFIG_SYS_RTC_REG_BASE_ADDR
There is some inconsistency between uses of CONFIG_RTC_DS13xx and CONFIG_SYS_RTC_DS13xx. Address this by dropping the "SYS" from these variables. Signed-off-by: Chris Packham <judge.packham@gmail.com> --- README | 2 +- drivers/rtc/ds1337.c | 16 ++++++++-------- include/configs/UCP1020.h | 2 +- include/configs/tqma6_wru4.h | 2 +- scripts/config_whitelist.txt | 8 +++----- 5 files changed, 14 insertions(+), 16 deletions(-)