Message ID | 1458045855-7726-4-git-send-email-purna.mandal@microchip.com |
---|---|
State | Superseded |
Headers | show |
Am 15.03.2016 um 13:44 schrieb Purna Chandra Mandal: > Enable MUSB host and USB storage support for Microchip > PIC32MZ[DA] Starter Kit. > > Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> > > --- > > Changes in v3: > - add arch specific reads{bwlq}, writes{bwlq} in respective arch io.h > - remove reads{bwlq}, writes{bwlq} in musb-new driver > > Changes in v2: > - compilation fix in drivers/usb/musb-new/linux-compat.h seperated > - compilation fix in drivers/gadget/f_mass_storage.c seperated > > arch/mips/dts/pic32mzda.dtsi | 10 ++++++++++ > arch/mips/dts/pic32mzda_sk.dts | 4 ++++ > configs/pic32mzdask_defconfig | 6 +++++- > include/configs/pic32mzdask.h | 7 +++++++ > 4 files changed, 26 insertions(+), 1 deletion(-) > > diff --git a/arch/mips/dts/pic32mzda.dtsi b/arch/mips/dts/pic32mzda.dtsi > index 7d180d9..57e4500 100644 > --- a/arch/mips/dts/pic32mzda.dtsi > +++ b/arch/mips/dts/pic32mzda.dtsi > @@ -171,4 +171,14 @@ > #address-cells = <1>; > #size-cells = <0>; > }; > + > + usb: musb@1f8e3000 { > + compatible = "microchip,pic32mzda-usb"; > + reg = <0x1f8e3000 0x1000>, > + <0x1f884000 0x1000>; > + reg-names = "mc", "control"; > + interrupts = <132 IRQ_TYPE_EDGE_RISING>, > + <133 IRQ_TYPE_LEVEL_HIGH>; > + status = "disabled"; > + }; > }; > diff --git a/arch/mips/dts/pic32mzda_sk.dts b/arch/mips/dts/pic32mzda_sk.dts > index e5ce0bd..0a7847e 100644 > --- a/arch/mips/dts/pic32mzda_sk.dts > +++ b/arch/mips/dts/pic32mzda_sk.dts > @@ -52,4 +52,8 @@ > ethernet_phy: lan8740_phy@0 { > reg = <0>; > }; > +}; > + > +&usb { > + status = "okay"; > }; > \ No newline at end of file > diff --git a/configs/pic32mzdask_defconfig b/configs/pic32mzdask_defconfig > index 1dbe1b5..544112f 100644 > --- a/configs/pic32mzdask_defconfig > +++ b/configs/pic32mzdask_defconfig > @@ -12,6 +12,7 @@ CONFIG_SYS_PROMPT="dask # " > CONFIG_LOOPW=y > CONFIG_CMD_MEMTEST=y > CONFIG_CMD_MEMINFO=y > +CONFIG_CMD_USB=y > # CONFIG_CMD_FPGA is not set > CONFIG_CMD_GPIO=y > CONFIG_CMD_RARP=y > @@ -28,6 +29,9 @@ CONFIG_DM_ETH=y > CONFIG_PIC32_ETH=y > CONFIG_PINCTRL=y > # CONFIG_PINCTRL_FULL is not set > -CONFIG_SYS_VSNPRINTF=y > +CONFIG_USB=y > +CONFIG_DM_USB=y > +CONFIG_USB_MUSB_HOST=y > +CONFIG_USB_STORAGE=y > CONFIG_USE_TINY_PRINTF=y > CONFIG_CMD_DHRYSTONE=y > diff --git a/include/configs/pic32mzdask.h b/include/configs/pic32mzdask.h > index 2d35a0b..1d5be2b 100644 > --- a/include/configs/pic32mzdask.h > +++ b/include/configs/pic32mzdask.h > @@ -117,6 +117,12 @@ > #define CONFIG_GENERIC_MMC > #define CONFIG_CMD_MMC > > +/*-------------------------------------------------- > + * USB Configuration > + */ > +#define CONFIG_USB_MUSB_PIO_ONLY > +#define CONFIG_SYS_CACHELINE_SIZE 16 I see CONFIG_SYS_CACHELINE_SIZE is used in drivers/usb/ in various memalign() calls. Actually we have ARCH_DMA_MINALIGN for this case. At least for MIPS I want to get rid of CONFIG_SYS_CACHELINE_SIZE in the future becasue we have auto-detection for that. If possible I'd like to see a patch which replaces CONFIG_SYS_CACHELINE_SIZE with ARCH_DMA_MINALIGN in drivers/user/. Marek what do you think? > + > /*----------------------------------------------------------------------- > * File System Configuration > */ > @@ -167,6 +173,7 @@ > > #define BOOT_TARGET_DEVICES(func) \ > func(MMC, mmc, 0) \ > + func(USB, usb, 0) \ > func(DHCP, dhcp, na) > > #include <config_distro_bootcmd.h> >
On 03/16/2016 10:12 AM, Daniel Schwierzeck wrote: > > > Am 15.03.2016 um 13:44 schrieb Purna Chandra Mandal: >> Enable MUSB host and USB storage support for Microchip >> PIC32MZ[DA] Starter Kit. >> >> Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> >> >> --- >> >> Changes in v3: >> - add arch specific reads{bwlq}, writes{bwlq} in respective arch io.h >> - remove reads{bwlq}, writes{bwlq} in musb-new driver >> >> Changes in v2: >> - compilation fix in drivers/usb/musb-new/linux-compat.h seperated >> - compilation fix in drivers/gadget/f_mass_storage.c seperated >> >> arch/mips/dts/pic32mzda.dtsi | 10 ++++++++++ >> arch/mips/dts/pic32mzda_sk.dts | 4 ++++ >> configs/pic32mzdask_defconfig | 6 +++++- >> include/configs/pic32mzdask.h | 7 +++++++ >> 4 files changed, 26 insertions(+), 1 deletion(-) >> >> diff --git a/arch/mips/dts/pic32mzda.dtsi b/arch/mips/dts/pic32mzda.dtsi >> index 7d180d9..57e4500 100644 >> --- a/arch/mips/dts/pic32mzda.dtsi >> +++ b/arch/mips/dts/pic32mzda.dtsi >> @@ -171,4 +171,14 @@ >> #address-cells = <1>; >> #size-cells = <0>; >> }; >> + >> + usb: musb@1f8e3000 { >> + compatible = "microchip,pic32mzda-usb"; >> + reg = <0x1f8e3000 0x1000>, >> + <0x1f884000 0x1000>; >> + reg-names = "mc", "control"; >> + interrupts = <132 IRQ_TYPE_EDGE_RISING>, >> + <133 IRQ_TYPE_LEVEL_HIGH>; >> + status = "disabled"; >> + }; >> }; >> diff --git a/arch/mips/dts/pic32mzda_sk.dts b/arch/mips/dts/pic32mzda_sk.dts >> index e5ce0bd..0a7847e 100644 >> --- a/arch/mips/dts/pic32mzda_sk.dts >> +++ b/arch/mips/dts/pic32mzda_sk.dts >> @@ -52,4 +52,8 @@ >> ethernet_phy: lan8740_phy@0 { >> reg = <0>; >> }; >> +}; >> + >> +&usb { >> + status = "okay"; >> }; >> \ No newline at end of file >> diff --git a/configs/pic32mzdask_defconfig b/configs/pic32mzdask_defconfig >> index 1dbe1b5..544112f 100644 >> --- a/configs/pic32mzdask_defconfig >> +++ b/configs/pic32mzdask_defconfig >> @@ -12,6 +12,7 @@ CONFIG_SYS_PROMPT="dask # " >> CONFIG_LOOPW=y >> CONFIG_CMD_MEMTEST=y >> CONFIG_CMD_MEMINFO=y >> +CONFIG_CMD_USB=y >> # CONFIG_CMD_FPGA is not set >> CONFIG_CMD_GPIO=y >> CONFIG_CMD_RARP=y >> @@ -28,6 +29,9 @@ CONFIG_DM_ETH=y >> CONFIG_PIC32_ETH=y >> CONFIG_PINCTRL=y >> # CONFIG_PINCTRL_FULL is not set >> -CONFIG_SYS_VSNPRINTF=y >> +CONFIG_USB=y >> +CONFIG_DM_USB=y >> +CONFIG_USB_MUSB_HOST=y >> +CONFIG_USB_STORAGE=y >> CONFIG_USE_TINY_PRINTF=y >> CONFIG_CMD_DHRYSTONE=y >> diff --git a/include/configs/pic32mzdask.h b/include/configs/pic32mzdask.h >> index 2d35a0b..1d5be2b 100644 >> --- a/include/configs/pic32mzdask.h >> +++ b/include/configs/pic32mzdask.h >> @@ -117,6 +117,12 @@ >> #define CONFIG_GENERIC_MMC >> #define CONFIG_CMD_MMC >> >> +/*-------------------------------------------------- >> + * USB Configuration >> + */ >> +#define CONFIG_USB_MUSB_PIO_ONLY >> +#define CONFIG_SYS_CACHELINE_SIZE 16 > > I see CONFIG_SYS_CACHELINE_SIZE is used in drivers/usb/ in various memalign() calls. Actually we have ARCH_DMA_MINALIGN for this case. At least for MIPS I want to get rid of CONFIG_SYS_CACHELINE_SIZE in the future becasue we have auto-detection for that. > > If possible I'd like to see a patch which replaces CONFIG_SYS_CACHELINE_SIZE with ARCH_DMA_MINALIGN in drivers/user/. Marek what do you think? I think that makes sense. >> + >> /*----------------------------------------------------------------------- >> * File System Configuration >> */ >> @@ -167,6 +173,7 @@ >> >> #define BOOT_TARGET_DEVICES(func) \ >> func(MMC, mmc, 0) \ >> + func(USB, usb, 0) \ >> func(DHCP, dhcp, na) >> >> #include <config_distro_bootcmd.h> >> >
diff --git a/arch/mips/dts/pic32mzda.dtsi b/arch/mips/dts/pic32mzda.dtsi index 7d180d9..57e4500 100644 --- a/arch/mips/dts/pic32mzda.dtsi +++ b/arch/mips/dts/pic32mzda.dtsi @@ -171,4 +171,14 @@ #address-cells = <1>; #size-cells = <0>; }; + + usb: musb@1f8e3000 { + compatible = "microchip,pic32mzda-usb"; + reg = <0x1f8e3000 0x1000>, + <0x1f884000 0x1000>; + reg-names = "mc", "control"; + interrupts = <132 IRQ_TYPE_EDGE_RISING>, + <133 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; }; diff --git a/arch/mips/dts/pic32mzda_sk.dts b/arch/mips/dts/pic32mzda_sk.dts index e5ce0bd..0a7847e 100644 --- a/arch/mips/dts/pic32mzda_sk.dts +++ b/arch/mips/dts/pic32mzda_sk.dts @@ -52,4 +52,8 @@ ethernet_phy: lan8740_phy@0 { reg = <0>; }; +}; + +&usb { + status = "okay"; }; \ No newline at end of file diff --git a/configs/pic32mzdask_defconfig b/configs/pic32mzdask_defconfig index 1dbe1b5..544112f 100644 --- a/configs/pic32mzdask_defconfig +++ b/configs/pic32mzdask_defconfig @@ -12,6 +12,7 @@ CONFIG_SYS_PROMPT="dask # " CONFIG_LOOPW=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_MEMINFO=y +CONFIG_CMD_USB=y # CONFIG_CMD_FPGA is not set CONFIG_CMD_GPIO=y CONFIG_CMD_RARP=y @@ -28,6 +29,9 @@ CONFIG_DM_ETH=y CONFIG_PIC32_ETH=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_FULL is not set -CONFIG_SYS_VSNPRINTF=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_MUSB_HOST=y +CONFIG_USB_STORAGE=y CONFIG_USE_TINY_PRINTF=y CONFIG_CMD_DHRYSTONE=y diff --git a/include/configs/pic32mzdask.h b/include/configs/pic32mzdask.h index 2d35a0b..1d5be2b 100644 --- a/include/configs/pic32mzdask.h +++ b/include/configs/pic32mzdask.h @@ -117,6 +117,12 @@ #define CONFIG_GENERIC_MMC #define CONFIG_CMD_MMC +/*-------------------------------------------------- + * USB Configuration + */ +#define CONFIG_USB_MUSB_PIO_ONLY +#define CONFIG_SYS_CACHELINE_SIZE 16 + /*----------------------------------------------------------------------- * File System Configuration */ @@ -167,6 +173,7 @@ #define BOOT_TARGET_DEVICES(func) \ func(MMC, mmc, 0) \ + func(USB, usb, 0) \ func(DHCP, dhcp, na) #include <config_distro_bootcmd.h>
Enable MUSB host and USB storage support for Microchip PIC32MZ[DA] Starter Kit. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> --- Changes in v3: - add arch specific reads{bwlq}, writes{bwlq} in respective arch io.h - remove reads{bwlq}, writes{bwlq} in musb-new driver Changes in v2: - compilation fix in drivers/usb/musb-new/linux-compat.h seperated - compilation fix in drivers/gadget/f_mass_storage.c seperated arch/mips/dts/pic32mzda.dtsi | 10 ++++++++++ arch/mips/dts/pic32mzda_sk.dts | 4 ++++ configs/pic32mzdask_defconfig | 6 +++++- include/configs/pic32mzdask.h | 7 +++++++ 4 files changed, 26 insertions(+), 1 deletion(-)