@@ -49,6 +49,7 @@ obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o
# xhci
obj-$(CONFIG_USB_XHCI) += xhci.o xhci-mem.o xhci-ring.o
+obj-$(CONFIG_USB_XHCI_DWC3) += xhci-dwc3.o
obj-$(CONFIG_USB_XHCI_KEYSTONE) += xhci-keystone.o
obj-$(CONFIG_USB_XHCI_EXYNOS) += xhci-exynos5.o
obj-$(CONFIG_USB_XHCI_OMAP) += xhci-omap.o
new file mode 100644
@@ -0,0 +1,74 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * DWC3 controller driver
+ *
+ * Author: Ramneek Mehresh<ramneek.mehresh@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <linux/usb/dwc3.h>
+
+void dwc3_set_mode(struct dwc3 *dwc3_reg, u32 mode)
+{
+ clrsetbits_le32(&dwc3_reg->g_ctl,
+ DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG),
+ DWC3_GCTL_PRTCAPDIR(mode));
+}
+
+void dwc3_core_soft_reset(struct dwc3 *dwc3_reg)
+{
+ /* Before Resetting PHY, put Core in Reset */
+ setbits_le32(&dwc3_reg->g_ctl, DWC3_GCTL_CORESOFTRESET);
+
+ /* reset USB3 phy - if required */
+ usb_phy_reset(dwc3_reg);
+
+ /* After PHYs are stable we can take Core out of reset state */
+ clrbits_le32(&dwc3_reg->g_ctl, DWC3_GCTL_CORESOFTRESET);
+}
+
+int dwc3_core_init(struct dwc3 *dwc3_reg)
+{
+ u32 reg;
+ u32 revision;
+ unsigned int dwc3_hwparams1;
+
+ revision = readl(&dwc3_reg->g_snpsid);
+ /* This should read as U3 followed by revision number */
+ if ((revision & DWC3_GSNPSID_MASK) != 0x55330000) {
+ puts("this is not a DesignWare USB3 DRD Core\n");
+ return -1;
+ }
+
+ dwc3_core_soft_reset(dwc3_reg);
+
+ dwc3_hwparams1 = readl(&dwc3_reg->g_hwparams1);
+
+ reg = readl(&dwc3_reg->g_ctl);
+ reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
+ reg &= ~DWC3_GCTL_DISSCRAMBLE;
+ switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc3_hwparams1)) {
+ case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
+ reg &= ~DWC3_GCTL_DSBLCLKGTNG;
+ break;
+ default:
+ debug("No power optimization available\n");
+ }
+
+ /*
+ * WORKAROUND: DWC3 revisions <1.90a have a bug
+ * where the device can fail to connect at SuperSpeed
+ * and falls back to high-speed mode which causes
+ * the device to enter a Connect/Disconnect loop
+ */
+ if ((revision & DWC3_REVISION_MASK) < 0x190a)
+ reg |= DWC3_GCTL_U2RSTECN;
+
+ writel(reg, &dwc3_reg->g_ctl);
+
+ return 0;
+}
@@ -191,4 +191,8 @@ struct dwc3 { /* offset: 0xC100 */
#define DWC3_DCTL_CSFTRST (1 << 30)
#define DWC3_DCTL_LSFTRST (1 << 29)
+void dwc3_set_mode(struct dwc3 *dwc3_reg, u32 mode);
+void dwc3_core_soft_reset(struct dwc3 *dwc3_reg);
+int dwc3_core_init(struct dwc3 *dwc3_reg);
+void usb_phy_reset(struct dwc3 *dwc3_reg);
#endif /* __DWC3_H_ */
Add support for DWC3 XHCI controller driver Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> --- drivers/usb/host/Makefile | 1 + drivers/usb/host/xhci-dwc3.c | 74 ++++++++++++++++++++++++++++++++++++++++++++ include/linux/usb/dwc3.h | 4 +++ 3 files changed, 79 insertions(+) create mode 100644 drivers/usb/host/xhci-dwc3.c