@@ -21,17 +21,6 @@
struct gpmc *gpmc_cfg;
#if defined(CONFIG_CMD_NAND)
-#if defined(GPMC_NAND_ECC_SP_x8_LAYOUT) || defined(GPMC_NAND_ECC_LP_x8_LAYOUT)
-static const u32 gpmc_m_nand[GPMC_MAX_REG] = {
- SMNAND_GPMC_CONFIG1,
- SMNAND_GPMC_CONFIG2,
- SMNAND_GPMC_CONFIG3,
- SMNAND_GPMC_CONFIG4,
- SMNAND_GPMC_CONFIG5,
- SMNAND_GPMC_CONFIG6,
- 0,
-};
-#else
static const u32 gpmc_m_nand[GPMC_MAX_REG] = {
M_NAND_GPMC_CONFIG1,
M_NAND_GPMC_CONFIG2,
@@ -40,7 +29,6 @@ static const u32 gpmc_m_nand[GPMC_MAX_REG] = {
M_NAND_GPMC_CONFIG5,
M_NAND_GPMC_CONFIG6, 0
};
-#endif
#endif /* CONFIG_CMD_NAND */
#if defined(CONFIG_CMD_ONENAND)
@@ -353,14 +353,6 @@ enum {
#define GPMC_CS_ENABLE 0x1
-#define SMNAND_GPMC_CONFIG1 0x00000800
-#define SMNAND_GPMC_CONFIG2 0x00141400
-#define SMNAND_GPMC_CONFIG3 0x00141400
-#define SMNAND_GPMC_CONFIG4 0x0F010F01
-#define SMNAND_GPMC_CONFIG5 0x010C1414
-#define SMNAND_GPMC_CONFIG6 0x1F0F0A80
-#define SMNAND_GPMC_CONFIG7 0x00000C44
-
#define M_NAND_GPMC_CONFIG1 0x00001800
#define M_NAND_GPMC_CONFIG2 0x00141400
#define M_NAND_GPMC_CONFIG3 0x00141400
@@ -54,12 +54,12 @@ static u32 gpmc_net_config[GPMC_MAX_REG] = {
};
static u32 gpmc_nand_config[GPMC_MAX_REG] = {
- SMNAND_GPMC_CONFIG1,
- SMNAND_GPMC_CONFIG2,
- SMNAND_GPMC_CONFIG3,
- SMNAND_GPMC_CONFIG4,
- SMNAND_GPMC_CONFIG5,
- SMNAND_GPMC_CONFIG6,
+ M_NAND_GPMC_CONFIG1,
+ M_NAND_GPMC_CONFIG2,
+ M_NAND_GPMC_CONFIG3,
+ M_NAND_GPMC_CONFIG4,
+ M_NAND_GPMC_CONFIG5,
+ M_NAND_GPMC_CONFIG6,
0,
};
@@ -141,7 +141,6 @@
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
#define CONFIG_CMD_NAND
-#define GPMC_NAND_ECC_LP_x8_LAYOUT
#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:2m(spl)," \
@@ -150,7 +150,6 @@
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-#define GPMC_NAND_ECC_LP_x8_LAYOUT 1
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \
"128k(SPL.backup1)," \
@@ -137,7 +137,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
@@ -157,7 +157,6 @@
/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */
#define CONFIG_NAND_OMAP_ELM
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_DEVICE_WIDTH 8
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros to configure GPMC controller for x7 or x8 bit device connected to its interface. Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above macros can be completely removed. Signed-off-by: Pekon Gupta <pekon@ti.com> --- arch/arm/cpu/armv7/omap3/mem.c | 12 ------------ arch/arm/include/asm/arch-omap3/mem.h | 8 -------- board/compulab/cm_t35/cm_t35.c | 12 ++++++------ include/configs/cm_t335.h | 1 - include/configs/pengwyn.h | 1 - include/configs/tao3530.h | 1 - include/configs/tseries.h | 1 - 7 files changed, 6 insertions(+), 30 deletions(-)