@@ -12,53 +12,6 @@
#define GPMC_BUF_EMPTY 0
#define GPMC_BUF_FULL 1
-/* Generic ECC Layouts */
-/* Large Page x8 NAND device Layout */
-#ifdef GPMC_NAND_ECC_LP_x8_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 12,\
- .eccpos = {1, 2, 3, 4, 5, 6, 7, 8,\
- 9, 10, 11, 12},\
- .oobfree = {\
- {.offset = 13,\
- .length = 51 } } \
-}
-#endif
-
-/* Large Page x16 NAND device Layout */
-#ifdef GPMC_NAND_ECC_LP_x16_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 12,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9,\
- 10, 11, 12, 13},\
- .oobfree = {\
- {.offset = 14,\
- .length = 50 } } \
-}
-#endif
-
-/* Small Page x8 NAND device Layout */
-#ifdef GPMC_NAND_ECC_SP_x8_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 3,\
- .eccpos = {1, 2, 3},\
- .oobfree = {\
- {.offset = 4,\
- .length = 12 } } \
-}
-#endif
-
-/* Small Page x16 NAND device Layout */
-#ifdef GPMC_NAND_ECC_SP_x16_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 3,\
- .eccpos = {2, 3, 4},\
- .oobfree = {\
- {.offset = 5,\
- .length = 11 } } \
-}
-#endif
-
enum omap_ecc {
/* 1-bit ECC calculation by Software, Error detection by Software */
OMAP_ECC_HAM1_CODE_SW = 1, /* avoid un-initialized int can be 0x0 */
@@ -381,7 +381,6 @@
/* NAND support */
#ifdef CONFIG_NAND
#define CONFIG_CMD_NAND
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#if !defined(CONFIG_SPI_BOOT) && !defined(CONFIG_NOR_BOOT)
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \
@@ -188,7 +188,6 @@
#define CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION 1
@@ -268,7 +268,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
@@ -262,7 +262,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
@@ -165,8 +165,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x8_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
/* Environment information */
@@ -116,8 +116,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
@@ -143,8 +143,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
#if defined(CONFIG_CMD_NET)
@@ -321,7 +321,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
@@ -183,8 +183,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
@@ -208,7 +208,6 @@
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#elif defined(CONFIG_CMD_ONENAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
@@ -267,7 +267,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M /* Configure the PISMO */
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_BASE NAND_BASE
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */
@@ -295,7 +295,6 @@
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#endif
@@ -119,8 +119,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
@@ -131,8 +131,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
@@ -138,8 +138,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
@@ -158,7 +158,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/* Environment information */
@@ -432,7 +432,6 @@
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* physical address */
/* to access nand at */
/* CS0 */
@@ -186,7 +186,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
@@ -134,8 +134,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_BCH
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI params or nand_id[] table. And based on that it defines ECC layout. This patch 1) removes following board configs used for defining NAND ECC layout - GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND) - GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND) - GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND) - GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND) 2) removes unused #defines in common omap_gpmc.h depending on above configs Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5 Signed-off-by: Pekon Gupta <pekon@ti.com> --- arch/arm/include/asm/omap_gpmc.h | 47 ---------------------------------- include/configs/am335x_evm.h | 1 - include/configs/am335x_igep0033.h | 1 - include/configs/am3517_crane.h | 1 - include/configs/am3517_evm.h | 1 - include/configs/cm_t35.h | 2 -- include/configs/devkit8000.h | 2 -- include/configs/dig297.h | 2 -- include/configs/mcx.h | 1 - include/configs/omap3_beagle.h | 2 -- include/configs/omap3_evm_common.h | 1 - include/configs/omap3_igep00x0.h | 1 - include/configs/omap3_logic.h | 1 - include/configs/omap3_overo.h | 2 -- include/configs/omap3_pandora.h | 2 -- include/configs/omap3_zoom1.h | 2 -- include/configs/omap3_zoom2.h | 1 - include/configs/siemens-am33x-common.h | 1 - include/configs/tam3517-common.h | 1 - include/configs/tricorder.h | 2 -- 20 files changed, 74 deletions(-)