diff --git a/README b/README
index 294b39e..d47ebc1 100644
--- a/README
+++ b/README
@@ -2785,6 +2785,43 @@ Low Level (hardware related) configuration options:
 		and RPXsuper) to be able to adjust the position of
 		the IMMR register after a reset.
 
+- CONFIG_SYS_CCSRBAR_DEFAULT:
+		Default (power-on reset) physical address of CCSR on Freescale
+		PowerPC SOCs.
+
+- CONFIG_SYS_CCSRBAR:
+		Virtual address of CCSR.  On a 32-bit build, this is typically
+		the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
+
+		CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
+		for cross-platform code that uses that macro instead.
+
+- CONFIG_SYS_CCSRBAR_PHYS:
+		Physical address of CCSR.  CCSR can be relocated to a new
+		physical address, if desired.  In this case, this macro should
+		be set to that address.  Otherwise, it should be set to the
+		same value as CONFIG_SYS_CCSRBAR_DEFAULT.  For example, CCSR
+		is typically relocated on 36-bit builds.  It is recommended
+		that this macro be defined via the _HIGH and _LOW macros:
+
+		#define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
+			* 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
+
+- CONFIG_SYS_CCSRBAR_PHYS_HIGH:
+		Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS.  This value is typically
+		either 0 (32-bit build) or 0xF (36-bit build).  This macro is
+		used in assembly code, so it must not contain typecasts or
+		integer size suffixes (e.g. "ULL").
+
+- CONFIG_SYS_CCSRBAR_PHYS_LOW:
+		Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS.  This macro is
+		used in assembly code, so it must not contain typecasts or
+		integer size suffixes (e.g. "ULL").
+
+- CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
+		If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
+		forced to a value that ensures that CCSR is not relocated.
+
 - Floppy Disk Support:
 		CONFIG_SYS_FDC_DRIVE_NUMBER
 
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index 04ca989..3006548 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -23,6 +23,10 @@
 
 /* SoC specific defines for Freescale MPC85xx (PQ3) and QorIQ processors */
 
+#ifdef CONFIG_SYS_CCSRBAR_DEFAULT
+#error "Do not define CONFIG_SYS_CCSRBAR_DEFAULT in the board header file"
+#endif
+
 /* Number of TLB CAM entries we have on FSL Book-E chips */
 #if defined(CONFIG_E500MC)
 #define CONFIG_SYS_NUM_TLBCAMS		64
@@ -34,34 +38,41 @@
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		12
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8540)
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		8
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8541)
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		8
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8544)
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		10
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8548)
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		10
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8555)
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		8
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8560)
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		8
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8568)
 #define CONFIG_MAX_CPUS			1
@@ -70,6 +81,7 @@
 #define QE_MURAM_SIZE			0x10000UL
 #define MAX_QE_RISC			2
 #define QE_NUM_OF_SNUM			28
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8569)
 #define CONFIG_MAX_CPUS			1
@@ -78,11 +90,13 @@
 #define QE_MURAM_SIZE			0x20000UL
 #define MAX_QE_RISC			4
 #define QE_NUM_OF_SNUM			46
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 #elif defined(CONFIG_MPC8572)
 #define CONFIG_MAX_CPUS			2
 #define CONFIG_SYS_FSL_NUM_LAWS		12
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_DDR_115
 #define CONFIG_SYS_FSL_ERRATUM_DDR111_DDR134
 
@@ -105,6 +119,7 @@
 #define CONFIG_TSECV2
 #define CONFIG_FSL_PCIE_DISABLE_ASPM
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
@@ -115,6 +130,7 @@
 #define CONFIG_TSECV2
 #define CONFIG_FSL_PCIE_DISABLE_ASPM
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xffe00000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define QE_MURAM_SIZE			0x6000UL
@@ -127,6 +143,7 @@
 #define CONFIG_SYS_FSL_NUM_LAWS		12
 #define CONFIG_TSECV2
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define CONFIG_FSL_SATA_ERRATUM_A001
@@ -149,6 +166,7 @@
 #define CONFIG_TSECV2
 #define CONFIG_FSL_PCIE_DISABLE_ASPM
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
@@ -164,6 +182,7 @@
 #define QE_MURAM_SIZE			0x6000UL
 #define MAX_QE_RISC			1
 #define QE_NUM_OF_SNUM			28
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 
 /* P1017 is single core version of P1023 */
 #elif defined(CONFIG_P1017)
@@ -177,6 +196,7 @@
 #define CONFIG_SYS_BMAN_NUM_PORTALS	3
 #define CONFIG_SYS_FM_MURAM_SIZE	0x10000
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff600000
 
 #elif defined(CONFIG_P1020)
 #define CONFIG_MAX_CPUS			2
@@ -184,6 +204,7 @@
 #define CONFIG_TSECV2
 #define CONFIG_FSL_PCIE_DISABLE_ASPM
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
@@ -193,6 +214,7 @@
 #define CONFIG_TSECV2
 #define CONFIG_FSL_PCIE_DISABLE_ASPM
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define QE_MURAM_SIZE			0x6000UL
@@ -204,6 +226,7 @@
 #define CONFIG_SYS_FSL_NUM_LAWS		12
 #define CONFIG_TSECV2
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define CONFIG_FSL_SATA_ERRATUM_A001
@@ -219,6 +242,7 @@
 #define CONFIG_SYS_BMAN_NUM_PORTALS	3
 #define CONFIG_SYS_FM_MURAM_SIZE	0x10000
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff600000
 
 /* P1024 is lower end variant of P1020 */
 #elif defined(CONFIG_P1024)
@@ -227,6 +251,7 @@
 #define CONFIG_TSECV2
 #define CONFIG_FSL_PCIE_DISABLE_ASPM
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
@@ -237,6 +262,7 @@
 #define CONFIG_TSECV2
 #define CONFIG_FSL_PCIE_DISABLE_ASPM
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define QE_MURAM_SIZE			0x6000UL
@@ -248,6 +274,7 @@
 #define CONFIG_MAX_CPUS			1
 #define CONFIG_SYS_FSL_NUM_LAWS		12
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001
 
@@ -255,6 +282,7 @@
 #define CONFIG_MAX_CPUS			2
 #define CONFIG_SYS_FSL_NUM_LAWS		12
 #define CONFIG_SYS_FSL_SEC_COMPAT	2
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001
 
@@ -271,6 +299,7 @@
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB2_PHY_ENABLE
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
 #elif defined(CONFIG_PPC_P2041)
@@ -287,6 +316,7 @@
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB2_PHY_ENABLE
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
 #elif defined(CONFIG_PPC_P3041)
@@ -303,6 +333,7 @@
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB2_PHY_ENABLE
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
 #elif defined(CONFIG_PPC_P4040)
@@ -313,6 +344,7 @@
 #define CONFIG_SYS_FM_MURAM_SIZE	0x28000
 #define CONFIG_SYS_FSL_TBCLK_DIV	16
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,p4080-pcie"
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 
 #elif defined(CONFIG_PPC_P4080)
 #define CONFIG_MAX_CPUS			8
@@ -328,6 +360,7 @@
 #define CONFIG_SYS_FM_MURAM_SIZE	0x28000
 #define CONFIG_SYS_FSL_TBCLK_DIV	16
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,p4080-pcie"
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 #define CONFIG_SYS_FSL_ERRATUM_CPC_A002
 #define CONFIG_SYS_FSL_ERRATUM_CPC_A003
 #define CONFIG_SYS_FSL_ERRATUM_DDR_A003
@@ -356,6 +389,7 @@
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB2_PHY_ENABLE
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
 #elif defined(CONFIG_PPC_P5020)
@@ -372,10 +406,15 @@
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
 #define CONFIG_SYS_FSL_USB1_PHY_ENABLE
 #define CONFIG_SYS_FSL_USB2_PHY_ENABLE
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 
 #else
 #error Processor type not defined for this platform
 #endif
 
+#ifndef CONFIG_SYS_CCSRBAR_DEFAULT
+#error "CONFIG_SYS_CCSRBAR_DEFAULT is not defined for this platform"
+#endif
+
 #endif /* _ASM_MPC85xx_CONFIG_H_ */
diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h
index 783ed51..3253b18 100644
--- a/include/configs/MPC8536DS.h
+++ b/include/configs/MPC8536DS.h
@@ -127,22 +127,10 @@
 #define CONFIG_SYS_L2_SIZE		(512 << 10)
 #define CONFIG_SYS_INIT_L2_END	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS	0xfffe00000ull /* physical addr of CCSRBAR */
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR
-#endif
-#define CONFIG_SYS_IMMR	CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xffe00000
 
 #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSRBAR_DEFAULT	CONFIG_SYS_CCSRBAR
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif
 
 /* DDR Setup */
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index e1d933e..74ec3c8 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -89,15 +89,7 @@
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR1
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index 5918e64..c774aa1 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -62,14 +62,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR1
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index b25fb55..cab8ba6 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -74,14 +74,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 #define CONFIG_PANIC_HANG	/* do not reset board on panic */
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index c9a0f60..151d3f0 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -77,14 +77,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 4c580a3..4976dbb 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -62,14 +62,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR1
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index f55ef9d..6ff9078 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -86,15 +86,7 @@
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR1
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index f7df7f0..4317212 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -71,14 +71,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h
index fa626bb..cd96f7c 100644
--- a/include/configs/MPC8569MDS.h
+++ b/include/configs/MPC8569MDS.h
@@ -105,20 +105,10 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_L2_SIZE		(512 << 10)
 #define CONFIG_SYS_INIT_L2_END	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR
-						/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR
-						/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSRBAR_DEFAULT	CONFIG_SYS_CCSRBAR
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif
 
 /* DDR Setup */
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index bb8fb66..4451321 100644
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -112,22 +112,10 @@
 #define CONFIG_SYS_L2_SIZE		(512 << 10)
 #define CONFIG_SYS_INIT_L2_END	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS		0xfffe00000ull	/* physical addr of CCSRBAR */
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#endif
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xffe00000
 
 #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSRBAR_DEFAULT		CONFIG_SYS_CCSRBAR
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000      /* CCSRBAR Default */
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif
 
 /* DDR Setup */
diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h
index a118975..57affa6 100644
--- a/include/configs/P1022DS.h
+++ b/include/configs/P1022DS.h
@@ -64,18 +64,7 @@
 #define CONFIG_SYS_MEMTEST_START	0x00000000
 #define CONFIG_SYS_MEMTEST_END		0x7fffffff
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS		0xfffe00000ull
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR
-#endif
-#define CONFIG_SYS_IMMR			CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR		0xffe00000
 
 /* DDR Setup */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h
index 4f14a02..6b0c9f0 100644
--- a/include/configs/P1023RDS.h
+++ b/include/configs/P1023RDS.h
@@ -99,15 +99,6 @@ extern unsigned long get_clock_freq(void);
 
 #define CONFIG_SYS_LBC_LBCR	0x00000000	/* Implement conversion of
 						addresses in the LBC */
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff600000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xff600000	/* relocated CCSRBAR */
-/* physical addr of CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR
-#define CONFIG_SYS_IMMR	CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
 
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h
index df88b79..805d58b 100644
--- a/include/configs/P1_P2_RDB.h
+++ b/include/configs/P1_P2_RDB.h
@@ -148,24 +148,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_L2_SIZE		(512 << 10)
 #define CONFIG_SYS_INIT_L2_END		(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS	0xfffe00000ull
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR
-#endif
-							/* CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses */
-							/* CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xffe00000
 
 #if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSRBAR_DEFAULT	CONFIG_SYS_CCSRBAR
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000      /* CCSRBAR Default */
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif
 
 /* DDR Setup */
diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
index 90fe7c4..fca4c0b 100644
--- a/include/configs/P2020DS.h
+++ b/include/configs/P2020DS.h
@@ -118,18 +118,7 @@
 #define CONFIG_SYS_L2_SIZE		(512 << 10)
 #define CONFIG_SYS_INIT_L2_END	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xffe00000	/* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS		0xfffe00000ull	/* physical addr of CCSRBAR */
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#endif
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xffe00000
 
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h
index 2beb357..2adbd52 100644
--- a/include/configs/P2041RDB.h
+++ b/include/configs/P2041RDB.h
@@ -136,20 +136,6 @@
 #define CONFIG_SYS_L3_SIZE		(1024 << 10)
 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xfe000000	/* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS		0xffe000000ull
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR
-#endif
-/* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR
-
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 72559c0..b5612d6 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -94,20 +94,6 @@
 #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
 #endif
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default	*/
-
-#if XXX
-  #define CONFIG_SYS_CCSRBAR		0xfdf00000	/* relocated CCSRBAR	*/
-#else
-  #define CONFIG_SYS_CCSRBAR		0xff700000	/* default CCSRBAR	*/
-#endif
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR	*/
-
 #define CONFIG_SYS_SDRAM_SIZE		512		/* DDR is 512MB */
 
 /* DDR Setup */
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index b336723..daa1255 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -130,18 +130,11 @@
 #define CONFIG_SYS_MEMTEST_START	0x00000000
 #define CONFIG_SYS_MEMTEST_END		0x10000000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xFF700000	/* CCSRBAR Default	*/
 #ifdef CONFIG_TQM_BIGFLASH
-#define CONFIG_SYS_CCSRBAR	 	0xA0000000	/* relocated CCSRBAR	*/
-#else /* !CONFIG_TQM_BIGFLASH */
-#define CONFIG_SYS_CCSRBAR		0xE0000000	/* relocated CCSRBAR	*/
-#endif /* CONFIG_TQM_BIGFLASH */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR	*/
+#define CONFIG_SYS_CCSRBAR	 	0xA0000000
+#else
+#define CONFIG_SYS_CCSRBAR		0xE0000000
+#endif
 
 /*
  * DDR Setup
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
index 0b7becb..0174a95 100644
--- a/include/configs/corenet_ds.h
+++ b/include/configs/corenet_ds.h
@@ -144,19 +144,6 @@
 #define CONFIG_SYS_L3_SIZE		(1024 << 10)
 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xfe000000	/* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS		0xffe000000ull	/* physical addr of CCSRBAR */
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#endif
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
-
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
diff --git a/include/configs/mpq101.h b/include/configs/mpq101.h
index e76ca73..f0ed4d1 100644
--- a/include/configs/mpq101.h
+++ b/include/configs/mpq101.h
@@ -64,20 +64,8 @@
 
 #define CONFIG_SYS_CLK_FREQ      33000000 /* sysclk for MPC85xx */
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
-#define CONFIG_SYS_CCSRBAR         0xe0000000
-
-#ifdef CONFIG_PHYS_64BIT
-# define CONFIG_SYS_CCSRBAR_PHYS   0xfe0000000ull
-#else
-# define CONFIG_SYS_CCSRBAR_PHYS   CONFIG_SYS_CCSRBAR
-#endif
-
-#define CONFIG_SYS_IMMR            CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR		0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 7bf9fc7..5fcad08 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -103,14 +103,7 @@
 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 435b148..e0af0d2 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -92,20 +92,6 @@
 #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
 #endif
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default	*/
-
-#if XXX
-  #define CONFIG_SYS_CCSRBAR		0xfdf00000	/* relocated CCSRBAR	*/
-#else
-  #define CONFIG_SYS_CCSRBAR		0xff700000	/* default CCSRBAR	*/
-#endif
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR	*/
-
 #define CONFIG_SYS_SDRAM_SIZE		512		/* DDR is 512MB */
 
 /* DDR Setup */
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 5f2fb1e..0f6bd9e 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -91,14 +91,7 @@
 #define CONFIG_SYS_MEMTEST_START	0x00400000
 #define CONFIG_SYS_MEMTEST_END		0x00C00000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xFF700000	/* CCSRBAR Default	*/
-#define CONFIG_SYS_CCSRBAR		0xE0000000	/* relocated CCSRBAR	*/
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR	*/
+#define CONFIG_SYS_CCSRBAR		0xE0000000
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index fc3881d..66738d5 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -109,12 +109,9 @@
 
 #ifdef CONFIG_SYS_RAMBOOT
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0x40000000	/* CCSRBAR by BDI cfg	*/
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default	*/
 #endif
-#define CONFIG_SYS_CCSRBAR             0xfdf00000      /* relocated CCSRBAR    */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR	*/
+#define CONFIG_SYS_CCSRBAR		0xfdf00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR1
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index d5dd94f..a1efe11 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -121,12 +121,10 @@
 
 #ifdef CONFIG_SYS_RAMBOOT
 #define CONFIG_SYS_CCSRBAR_DEFAULT	0x40000000	/* CCSRBAR by BDI cfg	*/
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default	*/
 #endif
-#define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR	*/
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR	*/
+
+#define CONFIG_SYS_CCSRBAR		0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR1
diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h
index b6b391f..42517c9 100644
--- a/include/configs/xpedite520x.h
+++ b/include/configs/xpedite520x.h
@@ -78,14 +78,8 @@
 #define CONFIG_BTB			/* toggle branch predition */
 #define CONFIG_ENABLE_36BIT_PHYS	1
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xef000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /*
  * Diagnostics
diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h
index a74766d..202f209 100644
--- a/include/configs/xpedite537x.h
+++ b/include/configs/xpedite537x.h
@@ -96,14 +96,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_BTB			/* toggle branch predition */
 #define CONFIG_ENABLE_36BIT_PHYS	1
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xef000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /*
  * Diagnostics
diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
index 17aab5a..f13e4db 100644
--- a/include/configs/xpedite550x.h
+++ b/include/configs/xpedite550x.h
@@ -93,14 +93,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_BTB			/* toggle branch predition */
 #define CONFIG_ENABLE_36BIT_PHYS	1
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR		0xef000000	/* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR		0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /*
  * Diagnostics
diff --git a/include/mpc85xx.h b/include/mpc85xx.h
index 2495b99..4b61bc0 100644
--- a/include/mpc85xx.h
+++ b/include/mpc85xx.h
@@ -26,4 +26,51 @@
 #define SCCR_DFBRG10    0x00000002      /* BRGCLK division by 64 */
 #define SCCR_DFBRG11    0x00000003      /* BRGCLK division by 256 */
 
+/*
+ * Define default values for some CCSR macros to make header files cleaner*
+ *
+ * To completely disable CCSR relocation in a board header file, define
+ * CONFIG_SYS_CCSR_DO_NOT_RELOCATE.  This will force CONFIG_SYS_CCSRBAR_PHYS
+ * to a value that is the same as CONFIG_SYS_CCSRBAR.
+ */
+
+#ifdef CONFIG_SYS_CCSRBAR_PHYS
+#error "Do not define CONFIG_SYS_CCSRBAR_PHYS directly.  Use \
+	CONFIG_SYS_CCSRBAR_PHYS_LOW and CONFIG_SYS_CCSRBAR_PHYS_HIGH instead."
+#endif
+
+#ifdef CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#if defined(CONFIG_SYS_CCSRBAR_PHYS_LOW) || defined(CONFIG_SYS_CCSRBAR_PHYS_HIGH)
+#warning "CONFIG_SYS_CCSR_DO_NOT_RELOCATE is defined and will override \
+	existing definitions of CONFIG_SYS_CCSRBAR_PHYS_LOW and/or \
+	CONFIG_SYS_CCSRBAR_PHYS_HIGH."
+#endif
+#undef CONFIG_SYS_CCSRBAR_PHYS_HIGH
+#undef CONFIG_SYS_CCSRBAR_PHYS_LOW
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0
+#endif
+
+#ifndef CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_CCSRBAR 		CONFIG_SYS_CCSRBAR_DEFAULT
+#endif
+
+#ifndef CONFIG_SYS_CCSRBAR_PHYS_HIGH
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0xf
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0
+#endif
+#endif
+
+#ifndef CONFIG_SYS_CCSRBAR_PHYS_LOW
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW 	CONFIG_SYS_CCSRBAR_DEFAULT
+#endif
+
+#define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH * 1ull) << 32 | \
+				 CONFIG_SYS_CCSRBAR_PHYS_LOW)
+
+#ifndef CONFIG_SYS_IMMR
+#define CONFIG_SYS_IMMR 		CONFIG_SYS_CCSRBAR
+#endif
+
 #endif	/* __MPC85xx_H__ */
