| Message ID | 1301897422-27326-2-git-send-email-hs@denx.de |
|---|---|
| State | Accepted |
| Commit | 1b41493defcf8940bce91859de16d7a956ebc569 |
| Headers | show |
Hi Heiko, > - rev5 board has phy addr 1 -> adapt CONFIG_PHY_ADDR define > in board config file. > - also fixup the phy addr entry in dts, before booting > Linux. > > Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> Cheers Detlev
Dear Heiko Schocher, In message <1301897422-27326-2-git-send-email-hs@denx.de> you wrote: > - rev5 board has phy addr 1 -> adapt CONFIG_PHY_ADDR define > in board config file. > - also fixup the phy addr entry in dts, before booting > Linux. > > Signed-off-by: Heiko Schocher <hs@denx.de> > --- > board/digsy_mtc/digsy_mtc.c | 5 +++++ > include/configs/digsy_mtc.h | 4 ++++ > 2 files changed, 9 insertions(+), 0 deletions(-) Applied, thanks. Best regards, Wolfgang Denk
diff --git a/board/digsy_mtc/digsy_mtc.c b/board/digsy_mtc/digsy_mtc.c index cbfdc9e..79cb3f1 100644 --- a/board/digsy_mtc/digsy_mtc.c +++ b/board/digsy_mtc/digsy_mtc.c @@ -405,6 +405,9 @@ int update_flash_size (int flash_size) void ft_board_setup(void *blob, bd_t *bd) { + int phy_addr = CONFIG_PHY_ADDR; + char eth_path[] = "/soc5200@f0000000/mdio@3000/ethernet-phy@0"; + ft_cpu_setup(blob, bd); /* * There are 2 RTC nodes in the DTS, so remove @@ -422,5 +425,7 @@ void ft_board_setup(void *blob, bd_t *bd) #endif ft_adapt_flash_base(blob); #endif + /* fix up the phy address */ + do_fixup_by_path(blob, eth_path, "reg", &phy_addr, sizeof(int), 0); } #endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h index d9be2b5..d4ca30e 100644 --- a/include/configs/digsy_mtc.h +++ b/include/configs/digsy_mtc.h @@ -348,7 +348,11 @@ */ #define CONFIG_MPC5xxx_FEC 1 #define CONFIG_MPC5xxx_FEC_MII100 +#if defined(CONFIG_DIGSY_REV5) +#define CONFIG_PHY_ADDR 0x01 +#else #define CONFIG_PHY_ADDR 0x00 +#endif #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_NETCONSOLE /* include NetConsole support */
- rev5 board has phy addr 1 -> adapt CONFIG_PHY_ADDR define in board config file. - also fixup the phy addr entry in dts, before booting Linux. Signed-off-by: Heiko Schocher <hs@denx.de> --- board/digsy_mtc/digsy_mtc.c | 5 +++++ include/configs/digsy_mtc.h | 4 ++++ 2 files changed, 9 insertions(+), 0 deletions(-)