@@ -69,6 +69,14 @@ define Host/Install
$(INSTALL_BIN) $(HOST_BUILD_DIR)/plat/nxp/tools/byte_swap $(STAGING_DIR_HOST)/bin/tfa-byte-swap
endef
+define Package/tfa-layerscape/ls1012afrdm
+ TITLE:=NXP LS1012AFRDM Trusted Firmware
+ PLAT:=ls1012afrdm
+ BOOT_MODE:=qspi
+ BIN_BL2:=build/ls1012afrdm/release/bl2_qspi.pbl
+ BIN_FIP:=build/ls1012afrdm/release/fip.bin
+endef
+
define Package/tfa-layerscape/ls1012ardb
TITLE:=NXP LS1012ARDB Trusted Firmware
PLAT:=ls1012ardb
@@ -142,6 +150,7 @@ define Package/tfa-layerscape/ls2088ardb
endef
TFAS := \
+ ls1012afrdm \
ls1012ardb \
ls1012afrwy \
ls1043ardb \
@@ -27,6 +27,12 @@ define U-Boot/Default
ENV_SIZE:=0x2000
endef
+define U-Boot/ls1012afrdm
+ NAME:=NXP LS1012AFRDM
+ UBOOT_CONFIG:=ls1012afrdm_tfa
+ ENV_SIZE:=0x40000
+endef
+
define U-Boot/ls1012ardb
NAME:=NXP LS1012ARDB
UBOOT_CONFIG:=ls1012ardb_tfa
@@ -102,6 +108,7 @@ endef
UBOOT_TARGETS := \
+ ls1012afrdm \
ls1012ardb \
ls1012afrwy \
ls1043ardb \
new file mode 100644
@@ -0,0 +1,8 @@
+fdtaddr=0x8f000000
+loadaddr=0x81000000
+fdt_high=0xffffffffffffffff
+initrd_high=0xffffffffffffffff
+qspi_boot=sf probe 0:0;sf read $fdtaddr f00000 100000;sf read $loadaddr 1000000 1000000;bootm $loadaddr - $fdtaddr
+bootargs=ubi.mtd=8 root=ubi0:rootfs rw rootfstype=ubifs noinitrd earlycon=uart8250,mmio,0x21c0500 console=ttyS0,115200 mtdparts=1550000.quadspi:1m(bl2),4m(fip),1m(u-boot-env),4m(reserved-1),3m(pfe),2m(reserved-2),1m(dtb),16m(kernel),32m(ubifs)
+bootcmd=echo starting OpenWrt ...;pfe stop;run qspi_boot
+bootdelay=3
@@ -28,6 +28,11 @@ define Package/layerscape-rcw/Config
endef
endef
+define Package/layerscape-rcw/ls1012afrdm
+ TITLE:=NXP LS1012AFRDM RCW binary
+ CONFIG:=ls1012afrdm/N_SSNP_3305/rcw_800.bin
+endef
+
define Package/layerscape-rcw/ls1012ardb
TITLE:=NXP LS1012ARDB RCW binary
CONFIG:=ls1012ardb/R_SPNH_3508/rcw_1000_default.bin
@@ -86,6 +91,7 @@ define Package/layerscape-rcw/Install
endef
RCWS := \
+ ls1012afrdm \
ls1012ardb \
ls1012afrwy \
ls1043ardb \
@@ -15,6 +15,29 @@ define Device/Default
KERNEL_ENTRY_POINT := 0x80080000
endef
+define Device/ls1012afrdm
+ DEVICE_VENDOR := NXP
+ DEVICE_MODEL := FRDM-LS1012A
+ DEVICE_PACKAGES += \
+ layerscape-ppfe \
+ tfa-ls1012afrdm \
+ kmod-ppfe
+ DEVICE_DTS := freescale/fsl-ls1012a-frdm
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 256KiB
+ PAGESIZE := 1
+ IMAGE/firmware.bin := \
+ ls-clean | \
+ ls-append $(1)-bl2.pbl | pad-to 1M | \
+ ls-append $(1)-fip.bin | pad-to 5M | \
+ ls-append $(1)-uboot-env.bin | pad-to 10M | \
+ ls-append pfe.itb | pad-to 15M | \
+ ls-append-dtb $$(DEVICE_DTS) | pad-to 16M | \
+ append-kernel | pad-to 32M | \
+ append-ubi | check-size 67108865
+endef
+TARGET_DEVICES += ls1012afrdm
+
define Device/ls1012ardb
DEVICE_VENDOR := NXP
DEVICE_MODEL := LS1012A-RDB
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the rest boards supported by LSDK. 0x000000000000-0x000000100000 : "bl2" 0x000000100000-0x000000500000 : "fip" 0x000000500000-0x000000600000 : "u-boot-env" 0x000000600000-0x000000a00000 : "reserved-1" 0x000000a00000-0x000000d00000 : "pfe" 0x000000d00000-0x000000f00000 : "reserved-2" 0x000000f00000-0x000001000000 : "dtb" 0x000001000000-0x000002000000 : "kernel" 0x000002000000-0x000004000000 : "ubifs" Specification SoC: LS1012A single core 800MHz RAM: 512 MB DDR3 Flash: 64 MB QSPI NOR Ethernet: 2x 10/100/1000 Mbps Connectors: µUSB 3.0 OTG µUSB 2.0 (debugging & power input) 2x 3.5mm jack for microphone & headphone (SGTL5000) Arduino Shield expansion with I2C, SPI, UART, and GPIO JTAG LEDS: 3x (non-configurable) Buttons: 1x (reset, non-configurable) Be advised that erasing or writing 64MB flash takes some time to finish. Do not reset the board until all operations end with success, otherwise You'll need external tools to re-program the flash chip. Installation Follow the QSPI programing procedure for LS1012AFRWY board in target/linux/layerscape/README, point 3.3. Don't forget about updating U-Boot environment with MAC addresses of ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1. As the LSDK images do not support sysupgrade, nor do changes in this commit, it's planed in upcoming submissions. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> --- package/boot/tfa-layerscape/Makefile | 9 ++++++++ package/boot/uboot-layerscape/Makefile | 7 ++++++ .../files/ls1012afrdm-uEnv.txt | 8 +++++++ package/firmware/layerscape/ls-rcw/Makefile | 6 +++++ target/linux/layerscape/image/armv8_64b.mk | 23 +++++++++++++++++++ 5 files changed, 53 insertions(+) create mode 100644 package/boot/uboot-layerscape/files/ls1012afrdm-uEnv.txt