@@ -439,6 +439,11 @@ zbt-we826-16M|\
zbt-we826-32M)
set_wifi_led "zbt-we826:green:wifi"
;;
+zbtlink,we1026-h-32m)
+ set_wifi_led "we1026-h:green:wifi"
+ ucidef_set_led_switch "lan" "lan" "we1026-h:green:lan" "switch0" "0x8"
+ ucidef_set_led_switch "wan" "wan" "we1026-h:green:wan" "switch0" "0x10"
+ ;;
zbtlink,zbt-we1226)
set_wifi_led "$boardname:green:wlan"
ucidef_set_led_switch "lan1" "LAN1" "$boardname:green:lan1" "switch0" "0x01"
@@ -427,7 +427,8 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
;;
- wcr-1166ds)
+ wcr-1166ds|\
+ zbtlink,we1026-h-32m)
ucidef_add_switch "switch0" \
"3:lan" "4:wan" "6@eth0"
;;
new file mode 100644
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "WE1026-H.dtsi"
+
+/ {
+ compatible = "zbtlink,we1026-h-32m", "zbtlink,we1026-h",
+ "zbtlink,we1026","ralink,mt7620a-soc";
+ model = "ZBT WE1026-H (32M)";
+};
+
+&firmware {
+ reg = <0x50000 0x1fb0000>;
+};
new file mode 100644
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "WE1026.dtsi"
+
+/ {
+ compatible = "zbtlink,we1026-h", "zbtlink,we1026",
+ "ralink,mt7620a-soc";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: usb {
+ label = "we1026-h:green:usb";
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ };
+
+ lan {
+ label = "we1026-h:green:lan";
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ };
+
+ wan {
+ label = "we1026-h:green:wan";
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi {
+ label = "we1026-h:green:wifi";
+ gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+};
@@ -812,6 +812,15 @@ define Device/we1026-5g-16m
endef
TARGET_DEVICES += we1026-5g-16m
+define Device/zbtlink_we1026-h-32m
+ DTS := WE1026-H-32M
+ IMAGE_SIZE := 32448k
+ DEVICE_TITLE := Zbtlink ZBT-WE1026-H (32M)
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620 \
+ kmod-ledtrig-netdev
+endef
+TARGET_DEVICES += zbtlink_we1026-h-32m
+
define Device/zbt-ape522ii
DTS := ZBT-APE522II
DEVICE_TITLE := Zbtlink ZBT-APE522II
This commit adds support for the ZBT WE1026-H, an outdoor AP with support for adding an internal LTE modem. The detailed specs are: * CPU: MT7620A * 2x 10/100Mbps Ethernet (LAN port has passive PoE support). * 16/32 MB Flash. * 128/256 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slot (only USB2.0 bus). * 1x SIM slot (standard size). * 1x 2.4Ghz WIFI (rt2800). * 1x button. * 6x LEDS (4 GPIO-controlled). * 1x micro-SD reader. The following have been tested and working: - Ethernet switch - Wifi - Mini-PCIe slot + SIM slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or ito recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. Notes: * The LED labeled "USB" is used as the power LED. When binding this LED to a usbport, the LED is switched on all the time due to the presence of an internal hub. Thus, it does not really signal any USB-information. * I only have the 32MB version and have only added support for this device. However, the files are structured so that adding support for the 16MB version should be easy. * Only the LAN port is accessible from the outside of the casing and LEDs are not visible. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> --- .../ramips/base-files/etc/board.d/01_leds | 5 +++ .../ramips/base-files/etc/board.d/02_network | 3 +- target/linux/ramips/dts/WE1026-H-32M.dts | 14 +++++++ target/linux/ramips/dts/WE1026-H.dtsi | 41 +++++++++++++++++++ target/linux/ramips/image/mt7620.mk | 9 ++++ 5 files changed, 71 insertions(+), 1 deletion(-) create mode 100644 target/linux/ramips/dts/WE1026-H-32M.dts create mode 100644 target/linux/ramips/dts/WE1026-H.dtsi