Message ID | 20210602120329.2444672-6-j.neuschaefer@gmx.net |
---|---|
State | New |
Headers | show |
Series | Nuvoton WPCM450 pinctrl and GPIO driver | expand |
On Wed, Jun 2, 2021 at 3:05 PM Jonathan Neuschäfer <j.neuschaefer@gmx.net> wrote: > > This driver is heavily based on the one for NPCM7xx, because the WPCM450 > is a predecessor of those SoCs. > > The biggest difference is in how the GPIO controller works. In the > WPCM450, the GPIO registers are not organized in multiple banks, but > rather placed continually into the same register block, and the driver > reflects this. > > Some functionality implemented in the hardware was (for now) left unused > in the driver, specifically blinking and pull-up/down. ... > +config PINCTRL_WPCM450 > + bool "Pinctrl and GPIO driver for Nuvoton WPCM450" Why it can't be a module? > + depends on (ARCH_WPCM450 || COMPILE_TEST) && OF Is it really OF dependent (see below)? > + select PINMUX > + select PINCONF > + select GENERIC_PINCONF > + select GPIOLIB > + select GPIO_GENERIC > + select GPIOLIB_IRQCHIP > + help > + Say Y here to enable pin controller and GPIO support > + for the Nuvoton WPCM450 SoC. From this help it's not clear why user should or shouldn't enable it. Please, elaborate (and hence fix checkpatch warning). ... > +#include <linux/module.h> mod_devicetable.h > +#include <linux/of.h> > +#include <linux/of_address.h> > +#include <linux/of_irq.h> > +#include <linux/pinctrl/machine.h> > +#include <linux/pinctrl/pinconf.h> > +#include <linux/pinctrl/pinconf-generic.h> > +#include <linux/pinctrl/pinctrl.h> > +#include <linux/pinctrl/pinmux.h> Can you move this group... > +#include <linux/platform_device.h> > +#include <linux/regmap.h> ...here? It will show the relation with pin control subsystem and separate from global / generic headers. ... > + /* > + * This spinlock protects registers and struct wpcm450_pinctrl fields spin lock > + * against concurrent access. > + */ ... > +/* GPIO handling in the pinctrl driver */ > + Useless. ... > +static int wpcm450_gpio_get_direction(struct gpio_chip *chip, > + unsigned int offset) > +{ > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); > + const struct wpcm450_port *port = to_port(offset); > + unsigned long flags; > + u32 cfg0; > + int dir; > + > + spin_lock_irqsave(&pctrl->lock, flags); > + if (port->cfg0) { > + cfg0 = ioread32(pctrl->gpio_base + port->cfg0); > + dir = !(cfg0 & port_mask(port, offset)); > + } else { > + /* If cfg0 is unavailable, the GPIO is always an input */ > + dir = 1; > + } Why above is under spin lock? Same question for all other similar places in different functions, if any. > + spin_unlock_irqrestore(&pctrl->lock, flags); > + return dir; > +} ... > +static int wpcm450_gpio_direction_output(struct gpio_chip *chip, > + unsigned int offset, int value) > +{ > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); > + const struct wpcm450_port *port = to_port(offset); > + unsigned long flags; > + u32 dataout, cfg0; > + int ret = 0; Redundant. Can do it without it. > + spin_lock_irqsave(&pctrl->lock, flags); > + if (port->cfg0) { > + } else { > + ret = -EINVAL; > + } > + spin_unlock_irqrestore(&pctrl->lock, flags); > + return ret; > +} ... > +/* Interrupt support */ > + Useless besides being in a bad style. ... > +static int event_bitmask(int gpio) > +{ > + if (gpio >= 0 && gpio < 16) > + return BIT(gpio); > + if (gpio == 24 || gpio == 25) > + return BIT(gpio - 8); > + return -EINVAL; > +} Can you consider to use bitmap_bitremap() > +static int event_bitnum_to_gpio(int num) > +{ > + if (num >= 0 && num < 16) > + return num; > + if (num == 16 || num == 17) > + return num + 8; > + return -EINVAL; > +} Ditto. See gpio-xilinx.c for example. ... > +static void wpcm450_gpio_irq_ack(struct irq_data *d) > +{ > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(irq_data_get_irq_chip_data(d)); > + int mask = event_bitmask(d->hwirq); Move the assignment closer to the check. Ditto for other same and similar cases in the code. > + unsigned long flags; > + > + if (mask < 0) > + return; > +} ... > + int mask = event_bitmask(d->hwirq); Use irqd_to_hwirq() (please check that I spelled it correctly). Same for all hwirq getters. ... > +static void wpcm450_gpio_fix_evpol(struct wpcm450_pinctrl *pctrl, unsigned long all) > +{ > + int bitnum; Can it be negative? > + for_each_set_bit(bitnum, &all, 32) { > + int gpio = event_bitnum_to_gpio(bitnum); > + u32 mask = BIT(bitnum), evpol; unsigned long evpol; > + int level; > + > + do { > + evpol = ioread32(pctrl->gpio_base + WPCM450_GPEVPOL); > + level = wpcm450_gpio_get(&pctrl->gc, gpio); > + /* Switch event polarity to the opposite of the current level */ > + if (level) > + evpol &= ~mask; > + else > + evpol |= mask; __assign_bit(bitnum, &evpol, level); > + > + iowrite32(evpol, pctrl->gpio_base + WPCM450_GPEVPOL); > + } while (wpcm450_gpio_get(&pctrl->gc, gpio) != level); > + } > +} ... > +static int wpcm450_gpio_set_irq_type(struct irq_data *d, unsigned int flow_type) > +{ Consider to assign handler type here. > +} ... > +/* pinmux handing */ > + Useless. ... > +/* > + * pin: name, number > + * group: name, npins, pins > + * function: name, ngroups, groups > + */ > +struct wpcm450_group { > + const char *name; > + const unsigned int *pins; > + int npins; > +}; Use struct group_desc from core.h. ... > +/* pinctrl_ops */ Useless. > +static int wpcm450_get_groups_count(struct pinctrl_dev *pctldev) > +{ > + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); > + dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(wpcm450_groups)); Ditto. > + return ARRAY_SIZE(wpcm450_groups); > +} ... > +/* pinmux_ops */ Useless. ... > +static int wpcm450_gpio_request_enable(struct pinctrl_dev *pctldev, > + struct pinctrl_gpio_range *range, > + unsigned int offset) > +{ > + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); > + if (!range) { > + dev_err(npcm->dev, "invalid range\n"); > + return -EINVAL; > + } Dead code? > + if (!range->gc) { > + dev_err(npcm->dev, "invalid gpiochip\n"); > + return -EINVAL; > + } Dead code? > + wpcm450_setfunc(npcm->gcr_regmap, &offset, 1, fn_gpio); > + > + return 0; > +} ... > +/* Release GPIO back to pinctrl mode */ > +static void wpcm450_gpio_request_free(struct pinctrl_dev *pctldev, > + struct pinctrl_gpio_range *range, > + unsigned int offset) > +{ > + struct wpcm450_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); > + int virq; > + > + virq = irq_find_mapping(pctrl->domain, offset); > + if (virq) > + irq_dispose_mapping(virq); Why it needs to be done here? What about the GPIO library API that does some additional stuff? > +} ... > +/* pinconf_ops */ Useless. ... > +static int debounce_bitmask(int gpio) > +{ > + if (gpio >= 0 && gpio < 16) > + return BIT(gpio); > + return -EINVAL; > +} I don't see users of it except one below, care to inline? > +static int wpcm450_config_get(struct pinctrl_dev *pctldev, unsigned int pin, > + unsigned long *config) > +{ > + switch (param) { > + case PIN_CONFIG_INPUT_DEBOUNCE: > + mask = debounce_bitmask(pin); > + if (mask < 0) > + return mask; > + break; > + default: > + return -ENOTSUPP; > + } > + > + return 0; > +} ... > +/* Set multiple configuration settings for a pin */ Useless. ... > +static int wpcm450_config_set(struct pinctrl_dev *pctldev, unsigned int pin, > + unsigned long *configs, unsigned int num_configs) > +{ > + struct wpcm450_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); > + int rc; Why out of a sudden different (inconsistent) name? > + return 0; > +} ... > + if (!of_find_property(np, "gpio-controller", NULL)) > + return -ENODEV; Dead code? ... > + pctrl->gpio_base = of_iomap(np, 0); devm_platform_ioremap_resource(); > + if (!pctrl->gpio_base) { > + dev_err(pctrl->dev, "Resource fail for GPIO controller\n"); > + return -ENOMEM; > + } Here leak of resources. See above. ... > + pctrl->gc.get_direction = wpcm450_gpio_get_direction; > + pctrl->gc.direction_input = wpcm450_gpio_direction_input; > + pctrl->gc.direction_output = wpcm450_gpio_direction_output; > + pctrl->gc.get = wpcm450_gpio_get; > + pctrl->gc.set = wpcm450_gpio_set; No ->set_config()? ... > + girq->default_type = IRQ_TYPE_NONE; > + girq->handler = handle_level_irq; Use ->irq_set_type() for this. Here should be handle_bad_irq(). > + for (i = 0; i < WPCM450_NUM_GPIO_IRQS; i++) { > + int irq = irq_of_parse_and_map(np, i); fwnode_get_irq() > + if (irq < 0) { > + dev_err(pctrl->dev, "No IRQ for GPIO controller\n"); > + return irq; > + } > + girq->parents[i] = irq; > + } ... > + pctrl->pctldev = devm_pinctrl_register(&pdev->dev, > + &wpcm450_pinctrl_desc, pctrl); > + if (IS_ERR(pctrl->pctldev)) { > + dev_err(&pdev->dev, "Failed to register pinctrl device\n"); > + return PTR_ERR(pctrl->pctldev); Shouldn't it be return dev_err_probe(...); here? > + } ... > + pr_info("WPCM450 pinctrl and GPIO driver probed\n"); Besides you have to use dev_*() this is completely useless and noisy message. ... > +static const struct of_device_id wpcm450_pinctrl_match[] = { > + { .compatible = "nuvoton,wpcm450-pinctrl" }, > + { }, Comma is not needed for terminator line. > +}; ... > + .suppress_bind_attrs = true, Why?
Hi "Jonathan, I love your patch! Perhaps something to improve: [auto build test WARNING on pinctrl/devel] [also build test WARNING on robh/for-next linus/master v5.13-rc4 next-20210602] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch] url: https://github.com/0day-ci/linux/commits/Jonathan-Neusch-fer/Nuvoton-WPCM450-pinctrl-and-GPIO-driver/20210602-200629 base: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git devel config: alpha-allyesconfig (attached as .config) compiler: alpha-linux-gcc (GCC) 9.3.0 reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # https://github.com/0day-ci/linux/commit/42f026e0692ea0083822284f98d2b82dcb6141ef git remote add linux-review https://github.com/0day-ci/linux git fetch --no-tags linux-review Jonathan-Neusch-fer/Nuvoton-WPCM450-pinctrl-and-GPIO-driver/20210602-200629 git checkout 42f026e0692ea0083822284f98d2b82dcb6141ef # save the attached .config to linux build tree COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=alpha If you fix the issue, kindly add following tag as appropriate Reported-by: kernel test robot <lkp@intel.com> All warnings (new ones prefixed by >>): In file included from include/linux/printk.h:409, from include/linux/kernel.h:17, from include/asm-generic/bug.h:20, from arch/alpha/include/asm/bug.h:23, from include/linux/bug.h:5, from include/linux/thread_info.h:12, from include/asm-generic/current.h:5, from ./arch/alpha/include/generated/asm/current.h:1, from include/linux/sched.h:12, from include/linux/ratelimit.h:6, from include/linux/dev_printk.h:16, from include/linux/device.h:15, from drivers/pinctrl/nuvoton/pinctrl-wpcm450.c:6: drivers/pinctrl/nuvoton/pinctrl-wpcm450.c: In function 'wpcm450_get_groups_count': >> drivers/pinctrl/nuvoton/pinctrl-wpcm450.c:882:21: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=] 882 | dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(wpcm450_groups)); | ^~~~~~~~~~~~~~~~~~ include/linux/dynamic_debug.h:129:15: note: in definition of macro '__dynamic_func_call' 129 | func(&id, ##__VA_ARGS__); \ | ^~~~~~~~~~~ include/linux/dynamic_debug.h:161:2: note: in expansion of macro '_dynamic_func_call' 161 | _dynamic_func_call(fmt,__dynamic_dev_dbg, \ | ^~~~~~~~~~~~~~~~~~ include/linux/dev_printk.h:123:2: note: in expansion of macro 'dynamic_dev_dbg' 123 | dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~~~~~~~~~ include/linux/dev_printk.h:123:23: note: in expansion of macro 'dev_fmt' 123 | dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__) | ^~~~~~~ drivers/pinctrl/nuvoton/pinctrl-wpcm450.c:882:2: note: in expansion of macro 'dev_dbg' 882 | dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(wpcm450_groups)); | ^~~~~~~ drivers/pinctrl/nuvoton/pinctrl-wpcm450.c:882:35: note: format string is defined here 882 | dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(wpcm450_groups)); | ~^ | | | int | %ld vim +882 drivers/pinctrl/nuvoton/pinctrl-wpcm450.c 876 877 /* pinctrl_ops */ 878 static int wpcm450_get_groups_count(struct pinctrl_dev *pctldev) 879 { 880 struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); 881 > 882 dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(wpcm450_groups)); 883 return ARRAY_SIZE(wpcm450_groups); 884 } 885 --- 0-DAY CI Kernel Test Service, Intel Corporation https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
Hi "Jonathan,
I love your patch! Perhaps something to improve:
[auto build test WARNING on pinctrl/devel]
[also build test WARNING on robh/for-next linus/master v5.13-rc4 next-20210603]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Jonathan-Neusch-fer/Nuvoton-WPCM450-pinctrl-and-GPIO-driver/20210602-200629
base: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git devel
config: x86_64-randconfig-a004-20210603 (attached as .config)
compiler: clang version 13.0.0 (https://github.com/llvm/llvm-project d8e0ae9a76a62bdc6117630d59bf9967ac9bb4ea)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# install x86_64 cross compiling tool for clang build
# apt-get install binutils-x86-64-linux-gnu
# https://github.com/0day-ci/linux/commit/42f026e0692ea0083822284f98d2b82dcb6141ef
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Jonathan-Neusch-fer/Nuvoton-WPCM450-pinctrl-and-GPIO-driver/20210602-200629
git checkout 42f026e0692ea0083822284f98d2b82dcb6141ef
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross ARCH=x86_64
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All warnings (new ones prefixed by >>):
>> drivers/pinctrl/nuvoton/pinctrl-npcm7xx.c:1564:41: warning: format specifies type 'int' but the argument has type 'unsigned long' [-Wformat]
dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(npcm7xx_groups));
~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~
%lu
include/linux/dev_printk.h:126:46: note: expanded from macro 'dev_dbg'
dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
include/linux/kernel.h:42:25: note: expanded from macro 'ARRAY_SIZE'
#define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]) + __must_be_array(arr))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
vim +1564 drivers/pinctrl/nuvoton/pinctrl-npcm7xx.c
3b588e43ee5c7a Tomer Maimon 2018-08-08 1559
3b588e43ee5c7a Tomer Maimon 2018-08-08 1560 static int npcm7xx_get_groups_count(struct pinctrl_dev *pctldev)
3b588e43ee5c7a Tomer Maimon 2018-08-08 1561 {
3b588e43ee5c7a Tomer Maimon 2018-08-08 1562 struct npcm7xx_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev);
3b588e43ee5c7a Tomer Maimon 2018-08-08 1563
3b588e43ee5c7a Tomer Maimon 2018-08-08 @1564 dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(npcm7xx_groups));
3b588e43ee5c7a Tomer Maimon 2018-08-08 1565 return ARRAY_SIZE(npcm7xx_groups);
3b588e43ee5c7a Tomer Maimon 2018-08-08 1566 }
3b588e43ee5c7a Tomer Maimon 2018-08-08 1567
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
Hi Jonathan! thanks for your patch! On Wed, Jun 2, 2021 at 2:04 PM Jonathan Neuschäfer <j.neuschaefer@gmx.net> wrote: > > This driver is heavily based on the one for NPCM7xx, because the WPCM450 > is a predecessor of those SoCs. > > The biggest difference is in how the GPIO controller works. In the > WPCM450, the GPIO registers are not organized in multiple banks, but > rather placed continually into the same register block, and the driver > reflects this. This is unfortunate because now you can't use GPIO_GENERIC anymore. > Some functionality implemented in the hardware was (for now) left unused > in the driver, specifically blinking and pull-up/down. > > Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> (...) > +config PINCTRL_WPCM450 > + bool "Pinctrl and GPIO driver for Nuvoton WPCM450" > + depends on (ARCH_WPCM450 || COMPILE_TEST) && OF > + select PINMUX > + select PINCONF > + select GENERIC_PINCONF > + select GPIOLIB > + select GPIO_GENERIC You are not using GPIO_GENERIC > +struct wpcm450_port { > + /* Range of GPIOs in this port */ > + u8 base; > + u8 length; > + > + /* Register offsets (0 = register doesn't exist in this port) */ > + u8 cfg0, cfg1, cfg2; > + u8 blink; > + u8 dataout, datain; > +}; If you used to have "GPIO banks" and you now have "GPIO ports" what is the difference? Why can't these ports just be individula gpio_chip:s with their own device tree nodes inside the pin controller node? If you split it up then you can go back to using GPIO_GENERIC with bgpio_init() again which is a big win. All you seem to be doing is setting consecutive bits in a register by offset, which is what GPIO_GENERIC is for, just that it assumes offset is always from zero. If you split it into individual gpio_chips per register then you get this nice separation and code reuse. > +static const struct wpcm450_port *to_port(int offset) > +{ > + int i; > + > + for (i = 0; i < ARRAY_SIZE(wpcm450_ports); i++) > + if (offset >= wpcm450_ports[i].base && > + offset - wpcm450_ports[i].base < wpcm450_ports[i].length) > + return &wpcm450_ports[i]; > + return NULL; > +} Then you would also get away from this awkward thing. > +static u32 port_mask(const struct wpcm450_port *port, int offset) > +{ > + return BIT(offset - port->base); > +} And awkwardness like this. Generally splitting up gpio_chips is a very good idea. > +static int event_bitmask(int gpio) > +{ > + if (gpio >= 0 && gpio < 16) > + return BIT(gpio); > + if (gpio == 24 || gpio == 25) > + return BIT(gpio - 8); > + return -EINVAL; > +} > + > +static int event_bitnum_to_gpio(int num) > +{ > + if (num >= 0 && num < 16) > + return num; > + if (num == 16 || num == 17) > + return num + 8; > + return -EINVAL; > +} This is also a sign that you have several gpio_chips in practice and now you need all this awkwardness to get back to which GPIO is which instead of handling it in a per-chip manner. This can be done in different ways, the most radical is to have the pin control driver spawn child devices for each GPIO block/bank/port with its own driver, but it can also just register the individual gpio_chips. Yours, Linus Walleij
Hello, On Wed, Jun 02, 2021 at 03:50:39PM +0300, Andy Shevchenko wrote: > On Wed, Jun 2, 2021 at 3:05 PM Jonathan Neuschäfer > <j.neuschaefer@gmx.net> wrote: > > > > This driver is heavily based on the one for NPCM7xx, because the WPCM450 > > is a predecessor of those SoCs. > > > > The biggest difference is in how the GPIO controller works. In the > > WPCM450, the GPIO registers are not organized in multiple banks, but > > rather placed continually into the same register block, and the driver > > reflects this. > > > > Some functionality implemented in the hardware was (for now) left unused > > in the driver, specifically blinking and pull-up/down. > > ... > > > +config PINCTRL_WPCM450 > > + bool "Pinctrl and GPIO driver for Nuvoton WPCM450" > > Why it can't be a module? My mistake, it does indeed work as a module. I'll change it to tristate. > > + depends on (ARCH_WPCM450 || COMPILE_TEST) && OF > > Is it really OF dependent (see below)? After switching to the fwnode API, no. I'll drop the dependency. > > + select PINMUX > > + select PINCONF > > + select GENERIC_PINCONF > > + select GPIOLIB > > + select GPIO_GENERIC > > + select GPIOLIB_IRQCHIP > > + help > > + Say Y here to enable pin controller and GPIO support > > + for the Nuvoton WPCM450 SoC. > > >From this help it's not clear why user should or shouldn't enable it. > Please, elaborate (and hence fix checkpatch warning). I'll try something like this, but I'm open for better ideas: help Say Y or M here to enable pin controller and GPIO support for the Nuvoton WPCM450 SoC. This is strongly recommended when building a kernel that will run on this chip. If this driver is compiled as a module, it will be named pinctrl-wpcm450. I could mention some examples of functionality enabled by this driver: LEDs, host power control, Ethernet. (LEDs and host power control use GPIOs, at least on the Supermicro X9 board I've been using. Ethernet MDIO must be enabled through the pinctrl driver, unless the bootloader has done so already; on my board the bootloader doesn't do this.) > > +#include <linux/module.h> > > mod_devicetable.h I'll add it. > > > +#include <linux/of.h> > > +#include <linux/of_address.h> > > +#include <linux/of_irq.h> > > > +#include <linux/pinctrl/machine.h> > > +#include <linux/pinctrl/pinconf.h> > > +#include <linux/pinctrl/pinconf-generic.h> > > +#include <linux/pinctrl/pinctrl.h> > > +#include <linux/pinctrl/pinmux.h> > > Can you move this group... > > > +#include <linux/platform_device.h> > > +#include <linux/regmap.h> > > ...here? > > It will show the relation with pin control subsystem and separate from > global / generic headers. Will do. > > + * This spinlock protects registers and struct wpcm450_pinctrl fields > > spin lock Ok > > +/* GPIO handling in the pinctrl driver */ > > + > > Useless. Ok > > ... > > > +static int wpcm450_gpio_get_direction(struct gpio_chip *chip, > > + unsigned int offset) > > +{ > > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); > > + const struct wpcm450_port *port = to_port(offset); > > + unsigned long flags; > > + u32 cfg0; > > + int dir; > > + > > + spin_lock_irqsave(&pctrl->lock, flags); > > + if (port->cfg0) { > > + cfg0 = ioread32(pctrl->gpio_base + port->cfg0); > > > + dir = !(cfg0 & port_mask(port, offset)); > > + } else { > > + /* If cfg0 is unavailable, the GPIO is always an input */ > > + dir = 1; > > + } > > Why above is under spin lock? > Same question for all other similar places in different functions, if any. My intention was to protect the ioread32. But given that it's just a single MMIO read, this might be unnecessary. wpcm450_gpio_direction_input and a few other functions implement a read/modify/write cycle, where the lock makes more sense: spin_lock_irqsave(&pctrl->lock, flags); if (port->cfg0) { cfg0 = ioread32(pctrl->gpio_base + port->cfg0); cfg0 &= ~port_mask(port, offset); iowrite32(cfg0, pctrl->gpio_base + port->cfg0); } spin_unlock_irqrestore(&pctrl->lock, flags); (Here, as above, the locking calls moved into the if block, but I'm not sure how much of an improvement that would be.) > > > + spin_unlock_irqrestore(&pctrl->lock, flags); > > + return dir; > > +} > > ... > > > +static int wpcm450_gpio_direction_output(struct gpio_chip *chip, > > + unsigned int offset, int value) > > +{ > > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); > > + const struct wpcm450_port *port = to_port(offset); > > + unsigned long flags; > > + u32 dataout, cfg0; > > > + int ret = 0; > > Redundant. Can do it without it. > > > + spin_lock_irqsave(&pctrl->lock, flags); > > + if (port->cfg0) { > > > + } else { > > + ret = -EINVAL; > > + } > > + spin_unlock_irqrestore(&pctrl->lock, flags); > > + return ret; > > +} I'll refactor it to return -EINVAL early. > > +/* Interrupt support */ > > + > > Useless besides being in a bad style. Ok, will remove. > > ... > > > +static int event_bitmask(int gpio) > > +{ > > + if (gpio >= 0 && gpio < 16) > > + return BIT(gpio); > > + if (gpio == 24 || gpio == 25) > > + return BIT(gpio - 8); > > + return -EINVAL; > > +} > > Can you consider to use bitmap_bitremap() > > +static int event_bitnum_to_gpio(int num) > > +{ > > + if (num >= 0 && num < 16) > > + return num; > > + if (num == 16 || num == 17) > > + return num + 8; > > + return -EINVAL; > > +} > > Ditto. > > See gpio-xilinx.c for example. I looked at it now. I'm not convinced it'll improve readability here. > > ... > > > +static void wpcm450_gpio_irq_ack(struct irq_data *d) > > +{ > > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(irq_data_get_irq_chip_data(d)); > > > + int mask = event_bitmask(d->hwirq); > > Move the assignment closer to the check. > Ditto for other same and similar cases in the code. Will do. > > > + unsigned long flags; > > + > > + if (mask < 0) > > + return; > > > +} > > ... > > > + int mask = event_bitmask(d->hwirq); > > Use irqd_to_hwirq() (please check that I spelled it correctly). > Same for all hwirq getters. Will do. > > ... > > > +static void wpcm450_gpio_fix_evpol(struct wpcm450_pinctrl *pctrl, unsigned long all) > > +{ > > + int bitnum; > > Can it be negative? No. I'll change it to unsigned int. > > > + for_each_set_bit(bitnum, &all, 32) { > > > + int gpio = event_bitnum_to_gpio(bitnum); > > + u32 mask = BIT(bitnum), evpol; > > unsigned long evpol; > > > + int level; > > + > > + do { > > + evpol = ioread32(pctrl->gpio_base + WPCM450_GPEVPOL); > > + level = wpcm450_gpio_get(&pctrl->gc, gpio); > > > + /* Switch event polarity to the opposite of the current level */ > > + if (level) > > + evpol &= ~mask; > > + else > > + evpol |= mask; > > __assign_bit(bitnum, &evpol, level); Ah, very useful. I'll use __assign_bit in a few places. > > +static int wpcm450_gpio_set_irq_type(struct irq_data *d, unsigned int flow_type) > > +{ > > Consider to assign handler type here. Will do. > > +/* pinmux handing */ > > + > > Useless. Ok. > > +/* > > + * pin: name, number > > + * group: name, npins, pins > > + * function: name, ngroups, groups > > + */ > > +struct wpcm450_group { > > + const char *name; > > + const unsigned int *pins; > > + int npins; > > +}; > > Use struct group_desc from core.h. Ok. > > +/* pinctrl_ops */ > > Useless. Ok > > > +static int wpcm450_get_groups_count(struct pinctrl_dev *pctldev) > > +{ > > + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); > > > + dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(wpcm450_groups)); > > Ditto. Removing this and similar messages. > > +/* pinmux_ops */ > > Useless. Ok > > ... > > > +static int wpcm450_gpio_request_enable(struct pinctrl_dev *pctldev, > > + struct pinctrl_gpio_range *range, > > + unsigned int offset) > > +{ > > + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); Oops, I forgot to change the name to pctrl here. > > > + if (!range) { > > + dev_err(npcm->dev, "invalid range\n"); > > + return -EINVAL; > > + } > > Dead code? Indeed, the range pointer is checked in pin_request(). > > > + if (!range->gc) { > > + dev_err(npcm->dev, "invalid gpiochip\n"); > > + return -EINVAL; > > + } > > Dead code? ... and range->gc isn't used here... I'll remove the check. > > > + wpcm450_setfunc(npcm->gcr_regmap, &offset, 1, fn_gpio); > > + > > + return 0; > > +} > > ... > > > +/* Release GPIO back to pinctrl mode */ > > +static void wpcm450_gpio_request_free(struct pinctrl_dev *pctldev, > > + struct pinctrl_gpio_range *range, > > + unsigned int offset) > > +{ > > + struct wpcm450_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); > > + int virq; > > + > > + virq = irq_find_mapping(pctrl->domain, offset); > > + if (virq) > > + irq_dispose_mapping(virq); > > Why it needs to be done here? I copied this function from the pinctrl-npcm7xx driver; I don't really see a reason to call irq_dispose_mapping here. > What about the GPIO library API that does some additional stuff? I don't know which gpiolib function would be appropriate here, sorry. > > +/* pinconf_ops */ > > Useless. Ok > > +static int debounce_bitmask(int gpio) > > +{ > > + if (gpio >= 0 && gpio < 16) > > + return BIT(gpio); > > + return -EINVAL; > > +} > > I don't see users of it except one below, care to inline? It should have been used in wpcm450_config_set_one, but I missed that. > > +static int wpcm450_config_get(struct pinctrl_dev *pctldev, unsigned int pin, > > + unsigned long *config) > > +{ > > > + switch (param) { > > + case PIN_CONFIG_INPUT_DEBOUNCE: > > + mask = debounce_bitmask(pin); > > + if (mask < 0) > > + return mask; > > > + break; > > + default: > > + return -ENOTSUPP; > > + } > > + > > + return 0; > > +} > > ... > > > +/* Set multiple configuration settings for a pin */ > > Useless. Ok. > > ... > > > +static int wpcm450_config_set(struct pinctrl_dev *pctldev, unsigned int pin, > > + unsigned long *configs, unsigned int num_configs) > > +{ > > + struct wpcm450_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); > > > + int rc; > > Why out of a sudden different (inconsistent) name? No particular reason. I'll change it to ret. > > > + return 0; > > +} > > ... > > > + if (!of_find_property(np, "gpio-controller", NULL)) > > + return -ENODEV; > > Dead code? The point here was to check if the node is marked as a GPIO controller, with the boolean property "gpio-controller" (so device_property_read_bool would probably be more appropriate). However, since the gpio-controller property is already defined as required in the DT binding, I'm not sure it's worth checking here. > > ... > > > + pctrl->gpio_base = of_iomap(np, 0); > > devm_platform_ioremap_resource(); Will change. > > > + if (!pctrl->gpio_base) { > > + dev_err(pctrl->dev, "Resource fail for GPIO controller\n"); > > + return -ENOMEM; > > + } > > Here leak of resources. See above. > > ... > > > + pctrl->gc.get_direction = wpcm450_gpio_get_direction; > > + pctrl->gc.direction_input = wpcm450_gpio_direction_input; > > + pctrl->gc.direction_output = wpcm450_gpio_direction_output; > > + pctrl->gc.get = wpcm450_gpio_get; > > + pctrl->gc.set = wpcm450_gpio_set; > > No ->set_config()? Good point, I'll hook it up to wpcm450_config_set_one(). > > ... > > > + girq->default_type = IRQ_TYPE_NONE; > > > + girq->handler = handle_level_irq; > > Use ->irq_set_type() for this. Here should be handle_bad_irq(). Ok. > > > + for (i = 0; i < WPCM450_NUM_GPIO_IRQS; i++) { > > > + int irq = irq_of_parse_and_map(np, i); > > fwnode_get_irq() Indeed, will switch to fwnode_irq_get. > > > + if (irq < 0) { > > + dev_err(pctrl->dev, "No IRQ for GPIO controller\n"); > > + return irq; > > + } > > + girq->parents[i] = irq; > > + } > > ... > > > + pctrl->pctldev = devm_pinctrl_register(&pdev->dev, > > + &wpcm450_pinctrl_desc, pctrl); > > + if (IS_ERR(pctrl->pctldev)) { > > > + dev_err(&pdev->dev, "Failed to register pinctrl device\n"); > > + return PTR_ERR(pctrl->pctldev); > > Shouldn't it be return dev_err_probe(...); here? It's so far a rare pattern after devm_pinctrl_register, but it makes sense. Will change (in both cases above). (Perhaps I should also use dev_err_probe in wpcm450_gpio_register, since it's called from the probe function.) > > > + } > > ... > > > + pr_info("WPCM450 pinctrl and GPIO driver probed\n"); > > Besides you have to use dev_*() this is completely useless and noisy message. I'll remove this message and review the other messages. > > ... > > > +static const struct of_device_id wpcm450_pinctrl_match[] = { > > + { .compatible = "nuvoton,wpcm450-pinctrl" }, > > > + { }, > > Comma is not needed for terminator line. True, will remove. > > > +}; > > ... > > > + .suppress_bind_attrs = true, > > Why? Copied from pinctrl-npcm7xx, but I see no reason to keep it. > > -- > With Best Regards, > Andy Shevchenko Thank you for your detailed review, Jonthan Neuschäfer
On Sun, Jun 13, 2021 at 2:20 AM Jonathan Neuschäfer <j.neuschaefer@gmx.net> wrote: > On Wed, Jun 02, 2021 at 03:50:39PM +0300, Andy Shevchenko wrote: > > On Wed, Jun 2, 2021 at 3:05 PM Jonathan Neuschäfer > > <j.neuschaefer@gmx.net> wrote: ... > > > + help > > > + Say Y here to enable pin controller and GPIO support > > > + for the Nuvoton WPCM450 SoC. > > > > >From this help it's not clear why user should or shouldn't enable it. > > Please, elaborate (and hence fix checkpatch warning). > > I'll try something like this, but I'm open for better ideas: > > help > Say Y or M here to enable pin controller and GPIO support for > the Nuvoton WPCM450 SoC. This is strongly recommended when > building a kernel that will run on this chip. > > If this driver is compiled as a module, it will be named > pinctrl-wpcm450. This looks good enough. > I could mention some examples of functionality enabled by this driver: > LEDs, host power control, Ethernet. > > (LEDs and host power control use GPIOs, at least on the Supermicro X9 > board I've been using. Ethernet MDIO must be enabled through the > pinctrl driver, unless the bootloader has done so already; on my board > the bootloader doesn't do this.) ... > > > +static int wpcm450_gpio_get_direction(struct gpio_chip *chip, > > > + unsigned int offset) > > > +{ > > > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); > > > + const struct wpcm450_port *port = to_port(offset); > > > + unsigned long flags; > > > + u32 cfg0; > > > + int dir; > > > + > > > + spin_lock_irqsave(&pctrl->lock, flags); > > > + if (port->cfg0) { > > > + cfg0 = ioread32(pctrl->gpio_base + port->cfg0); > > > > > + dir = !(cfg0 & port_mask(port, offset)); > > > + } else { > > > + /* If cfg0 is unavailable, the GPIO is always an input */ > > > + dir = 1; > > > + } > > > > Why above is under spin lock? > > Same question for all other similar places in different functions, if any. > > My intention was to protect the ioread32. But given that it's just a > single MMIO read, this might be unnecessary. Sometimes it's necessary and I'm not talking about it. (I put blank lines around the code I was commenting on) So, What I meant above is to get something like this if (port->cfg0) { spin lock ... spin unlock } else { ... } or equivalent ideas. > > > + spin_unlock_irqrestore(&pctrl->lock, flags); > > > + return dir; > > > +} ... > > > +static int wpcm450_gpio_direction_output(struct gpio_chip *chip, > > > + unsigned int offset, int value) > > > +{ > > > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); > > > + const struct wpcm450_port *port = to_port(offset); > > > + unsigned long flags; > > > + u32 dataout, cfg0; > > > > > + int ret = 0; > > > > Redundant. Can do it without it. > > > > > + spin_lock_irqsave(&pctrl->lock, flags); > > > + if (port->cfg0) { > > > > > + } else { > > > + ret = -EINVAL; > > > + } > > > + spin_unlock_irqrestore(&pctrl->lock, flags); > > > + return ret; > > > +} > > I'll refactor it to return -EINVAL early. Here a similar approach can be used. ... > > What about the GPIO library API that does some additional stuff? > > I don't know which gpiolib function would be appropriate here, sorry. When you leave those request and release callbacks untouched the GPIO library will assign default ones. You may see what they do. ... > > > + if (!of_find_property(np, "gpio-controller", NULL)) > > > + return -ENODEV; > > > > Dead code? > > The point here was to check if the node is marked as a GPIO controller, > with the boolean property "gpio-controller" (so device_property_read_bool > would probably be more appropriate). > > However, since the gpio-controller property is already defined as > required in the DT binding, I'm not sure it's worth checking here. Exactly my point.
On Fri, Jun 04, 2021 at 11:31:07AM +0200, Linus Walleij wrote: > Hi Jonathan! > > thanks for your patch! > > On Wed, Jun 2, 2021 at 2:04 PM Jonathan Neuschäfer > <j.neuschaefer@gmx.net> wrote: > > > > This driver is heavily based on the one for NPCM7xx, because the WPCM450 > > is a predecessor of those SoCs. > > > > The biggest difference is in how the GPIO controller works. In the > > WPCM450, the GPIO registers are not organized in multiple banks, but > > rather placed continually into the same register block, and the driver > > reflects this. > > This is unfortunate because now you can't use GPIO_GENERIC anymore. > > > Some functionality implemented in the hardware was (for now) left unused > > in the driver, specifically blinking and pull-up/down. > > > > Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> > > (...) > > > +config PINCTRL_WPCM450 > > + bool "Pinctrl and GPIO driver for Nuvoton WPCM450" > > + depends on (ARCH_WPCM450 || COMPILE_TEST) && OF > > + select PINMUX > > + select PINCONF > > + select GENERIC_PINCONF > > + select GPIOLIB > > + select GPIO_GENERIC > > You are not using GPIO_GENERIC I'll remove the this line (depending on the outcome of the rest of the discussion). > > > +struct wpcm450_port { > > + /* Range of GPIOs in this port */ > > + u8 base; > > + u8 length; > > + > > + /* Register offsets (0 = register doesn't exist in this port) */ > > + u8 cfg0, cfg1, cfg2; > > + u8 blink; > > + u8 dataout, datain; > > +}; > > If you used to have "GPIO banks" and you now have > "GPIO ports" what is the difference? Why can't these ports > just be individula gpio_chip:s with their own device tree > nodes inside the pin controller node? The naming difference is a fairly arbitrary choice by me. The real difference is in how the GPIO registers are laid out. On NPCM7xx, there are blocks of registers at +0, +0x1000, +0x2000, etc., and within a block, the registers have the same offsets. On WPCM450, the registers are all mushed together as tightly as possible[1], so that (a) the ports/banks don't start at nice addresses, and (b) the register layout can't be predicted from the offset of the first register in a port (because not all ports have all registers). > If you split it up then you can go back to using > GPIO_GENERIC with bgpio_init() again which is a > big win. > > All you seem to be doing is setting consecutive > bits in a register by offset, which is what GPIO_GENERIC > is for, just that it assumes offset is always from zero. > If you split it into individual gpio_chips per register > then you get this nice separation and code reuse. Indeed, if I keep the wpcm450_ports table but use it to call bgpio_init() with the right register addresses, I think bgpio_init() can work. Thanks, Jonathan Neuschäfer [1]: https://github.com/neuschaefer/wpcm450/wiki/GPIOs-and-pinmux#gpio
On Sun, Jun 13, 2021 at 01:06:15PM +0300, Andy Shevchenko wrote: > On Sun, Jun 13, 2021 at 2:20 AM Jonathan Neuschäfer <j.neuschaefer@gmx.net> wrote: > > On Wed, Jun 02, 2021 at 03:50:39PM +0300, Andy Shevchenko wrote: > > > On Wed, Jun 2, 2021 at 3:05 PM Jonathan Neuschäfer <j.neuschaefer@gmx.net> wrote: [...] > > > > +static int wpcm450_gpio_get_direction(struct gpio_chip *chip, > > > > + unsigned int offset) > > > > +{ > > > > + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); > > > > + const struct wpcm450_port *port = to_port(offset); > > > > + unsigned long flags; > > > > + u32 cfg0; > > > > + int dir; > > > > + > > > > + spin_lock_irqsave(&pctrl->lock, flags); > > > > + if (port->cfg0) { > > > > + cfg0 = ioread32(pctrl->gpio_base + port->cfg0); > > > > > > > + dir = !(cfg0 & port_mask(port, offset)); > > > > + } else { > > > > + /* If cfg0 is unavailable, the GPIO is always an input */ > > > > + dir = 1; > > > > + } > > > > > > Why above is under spin lock? > > > Same question for all other similar places in different functions, if any. > > > > My intention was to protect the ioread32. But given that it's just a > > single MMIO read, this might be unnecessary. > > Sometimes it's necessary and I'm not talking about it. (I put blank > lines around the code I was commenting on) > > So, What I meant above is to get something like this > > if (port->cfg0) { > spin lock > ... > spin unlock > } else { > ... > } > > or equivalent ideas. Ah, in other words: Narrowing the scope of the lock as far as possible. I'll keep it in mind for v2. > > > What about the GPIO library API that does some additional stuff? > > > > I don't know which gpiolib function would be appropriate here, sorry. > > When you leave those request and release callbacks untouched the GPIO > library will assign default ones. You may see what they do. Ah, I see. I'll look into it. > ... > > > > > + if (!of_find_property(np, "gpio-controller", NULL)) > > > > + return -ENODEV; > > > > > > Dead code? > > > > The point here was to check if the node is marked as a GPIO controller, > > with the boolean property "gpio-controller" (so device_property_read_bool > > would probably be more appropriate). > > > > However, since the gpio-controller property is already defined as > > required in the DT binding, I'm not sure it's worth checking here. > > Exactly my point. Alright. Thanks, Jonthan Neuschäfer
diff --git a/MAINTAINERS b/MAINTAINERS index 288d6a1f2bb1f..ca5cb7f94b115 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2234,6 +2234,7 @@ S: Maintained F: Documentation/devicetree/bindings/*/*wpcm* F: arch/arm/boot/dts/nuvoton-wpcm450* F: arch/arm/mach-npcm/wpcm450.c +F: drivers/*/*/*wpcm* F: drivers/*/*wpcm* ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index 5ef5334a797fc..e355c78eecd58 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -56,7 +56,7 @@ obj-y += freescale/ obj-$(CONFIG_X86) += intel/ obj-y += mvebu/ obj-y += nomadik/ -obj-$(CONFIG_ARCH_NPCM7XX) += nuvoton/ +obj-y += nuvoton/ obj-$(CONFIG_PINCTRL_PXA) += pxa/ obj-$(CONFIG_ARCH_QCOM) += qcom/ obj-$(CONFIG_PINCTRL_RALINK) += ralink/ diff --git a/drivers/pinctrl/nuvoton/Kconfig b/drivers/pinctrl/nuvoton/Kconfig index 48ba0469edda6..f15d345b90083 100644 --- a/drivers/pinctrl/nuvoton/Kconfig +++ b/drivers/pinctrl/nuvoton/Kconfig @@ -1,4 +1,18 @@ # SPDX-License-Identifier: GPL-2.0-only + +config PINCTRL_WPCM450 + bool "Pinctrl and GPIO driver for Nuvoton WPCM450" + depends on (ARCH_WPCM450 || COMPILE_TEST) && OF + select PINMUX + select PINCONF + select GENERIC_PINCONF + select GPIOLIB + select GPIO_GENERIC + select GPIOLIB_IRQCHIP + help + Say Y here to enable pin controller and GPIO support + for the Nuvoton WPCM450 SoC. + config PINCTRL_NPCM7XX bool "Pinctrl and GPIO driver for Nuvoton NPCM7XX" depends on (ARCH_NPCM7XX || COMPILE_TEST) && OF diff --git a/drivers/pinctrl/nuvoton/Makefile b/drivers/pinctrl/nuvoton/Makefile index 886d00784cef5..9e66f5dc74bfc 100644 --- a/drivers/pinctrl/nuvoton/Makefile +++ b/drivers/pinctrl/nuvoton/Makefile @@ -1,4 +1,5 @@ # SPDX-License-Identifier: GPL-2.0 # Nuvoton pinctrl support +obj-$(CONFIG_PINCTRL_WPCM450) += pinctrl-wpcm450.o obj-$(CONFIG_PINCTRL_NPCM7XX) += pinctrl-npcm7xx.o diff --git a/drivers/pinctrl/nuvoton/pinctrl-wpcm450.c b/drivers/pinctrl/nuvoton/pinctrl-wpcm450.c new file mode 100644 index 0000000000000..b978b315ffc68 --- /dev/null +++ b/drivers/pinctrl/nuvoton/pinctrl-wpcm450.c @@ -0,0 +1,1230 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2016-2018 Nuvoton Technology corporation. +// Copyright (c) 2016, Dell Inc +// Copyright (c) 2021 Jonathan Neuschäfer + +#include <linux/device.h> +#include <linux/gpio/driver.h> +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/pinctrl/machine.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinconf-generic.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> + +/* GCR registers */ +#define WPCM450_GCR_MFSEL1 0x0C +#define WPCM450_GCR_MFSEL2 0x10 +#define WPCM450_GCR_NONE 0 + +/* GPIO event (interrupt) registers */ +#define WPCM450_GPEVTYPE 0x00 +#define WPCM450_GPEVPOL 0x04 +#define WPCM450_GPEVDBNC 0x08 +#define WPCM450_GPEVEN 0x0c +#define WPCM450_GPEVST 0x10 + +#define WPCM450_NUM_PORTS 8 +#define WPCM450_NUM_GPIOS 128 +#define WPCM450_NUM_GPIO_IRQS 4 + +struct wpcm450_pinctrl { + struct pinctrl_dev *pctldev; + struct device *dev; + struct irq_domain *domain; + struct regmap *gcr_regmap; + + void __iomem *gpio_base; + struct gpio_chip gc; + struct irq_chip irqc; + u32 both_edges; + + /* + * This spinlock protects registers and struct wpcm450_pinctrl fields + * against concurrent access. + */ + spinlock_t lock; +}; + +struct wpcm450_port { + /* Range of GPIOs in this port */ + u8 base; + u8 length; + + /* Register offsets (0 = register doesn't exist in this port) */ + u8 cfg0, cfg1, cfg2; + u8 blink; + u8 dataout, datain; +}; + +static const struct wpcm450_port wpcm450_ports[WPCM450_NUM_PORTS] = { + /* range cfg0 cfg1 cfg2 blink out in */ + { 0, 16, 0x14, 0x18, 0, 0, 0x1c, 0x20 }, + { 16, 16, 0x24, 0x28, 0x2c, 0x30, 0x34, 0x38 }, + { 32, 16, 0x3c, 0x40, 0x44, 0, 0x48, 0x4c }, + { 48, 16, 0x50, 0x54, 0x58, 0, 0x5c, 0x60 }, + { 64, 16, 0x64, 0x68, 0x6c, 0, 0x70, 0x74 }, + { 80, 16, 0x78, 0x7c, 0x80, 0, 0x84, 0x88 }, + { 96, 18, 0, 0, 0, 0, 0, 0x8c }, + { 114, 14, 0x90, 0x94, 0x98, 0, 0x9c, 0xa0 }, +}; + +static const struct wpcm450_port *to_port(int offset) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(wpcm450_ports); i++) + if (offset >= wpcm450_ports[i].base && + offset - wpcm450_ports[i].base < wpcm450_ports[i].length) + return &wpcm450_ports[i]; + return NULL; +} + +static u32 port_mask(const struct wpcm450_port *port, int offset) +{ + return BIT(offset - port->base); +} + +/* GPIO handling in the pinctrl driver */ + +static int wpcm450_gpio_get_direction(struct gpio_chip *chip, + unsigned int offset) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); + const struct wpcm450_port *port = to_port(offset); + unsigned long flags; + u32 cfg0; + int dir; + + spin_lock_irqsave(&pctrl->lock, flags); + if (port->cfg0) { + cfg0 = ioread32(pctrl->gpio_base + port->cfg0); + dir = !(cfg0 & port_mask(port, offset)); + } else { + /* If cfg0 is unavailable, the GPIO is always an input */ + dir = 1; + } + spin_unlock_irqrestore(&pctrl->lock, flags); + return dir; +} + +static int wpcm450_gpio_direction_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); + const struct wpcm450_port *port = to_port(offset); + unsigned long flags; + u32 cfg0; + + spin_lock_irqsave(&pctrl->lock, flags); + if (port->cfg0) { + cfg0 = ioread32(pctrl->gpio_base + port->cfg0); + cfg0 &= ~port_mask(port, offset); + iowrite32(cfg0, pctrl->gpio_base + port->cfg0); + } + spin_unlock_irqrestore(&pctrl->lock, flags); + return 0; +} + +static int wpcm450_gpio_direction_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); + const struct wpcm450_port *port = to_port(offset); + unsigned long flags; + u32 dataout, cfg0; + int ret = 0; + + spin_lock_irqsave(&pctrl->lock, flags); + if (port->cfg0) { + /* set output value first, direction second, to avoid glitches */ + dataout = ioread32(pctrl->gpio_base + port->dataout); + if (value) + dataout |= port_mask(port, offset); + else + dataout &= ~port_mask(port, offset); + iowrite32(dataout, pctrl->gpio_base + port->dataout); + + cfg0 = ioread32(pctrl->gpio_base + port->cfg0); + cfg0 |= port_mask(port, offset); + iowrite32(cfg0, pctrl->gpio_base + port->cfg0); + } else { + ret = -EINVAL; + } + spin_unlock_irqrestore(&pctrl->lock, flags); + return ret; +} + +static int wpcm450_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); + const struct wpcm450_port *port = to_port(offset); + unsigned long flags; + u32 datain; + + spin_lock_irqsave(&pctrl->lock, flags); + datain = ioread32(pctrl->gpio_base + port->datain); + spin_unlock_irqrestore(&pctrl->lock, flags); + + return !!(datain & port_mask(port, offset)); +} + +static void wpcm450_gpio_set(struct gpio_chip *chip, unsigned int offset, + int value) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(chip); + const struct wpcm450_port *port = to_port(offset); + unsigned long flags; + u32 dataout; + + spin_lock_irqsave(&pctrl->lock, flags); + if (port->dataout) { + dataout = ioread32(pctrl->gpio_base + port->dataout); + if (value) + dataout |= port_mask(port, offset); + else + dataout &= ~port_mask(port, offset); + iowrite32(dataout, pctrl->gpio_base + port->dataout); + } + spin_unlock_irqrestore(&pctrl->lock, flags); +} + +/* Interrupt support */ + +static int event_bitmask(int gpio) +{ + if (gpio >= 0 && gpio < 16) + return BIT(gpio); + if (gpio == 24 || gpio == 25) + return BIT(gpio - 8); + return -EINVAL; +} + +static int event_bitnum_to_gpio(int num) +{ + if (num >= 0 && num < 16) + return num; + if (num == 16 || num == 17) + return num + 8; + return -EINVAL; +} + +static void wpcm450_gpio_irq_ack(struct irq_data *d) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(irq_data_get_irq_chip_data(d)); + int mask = event_bitmask(d->hwirq); + unsigned long flags; + + if (mask < 0) + return; + + spin_lock_irqsave(&pctrl->lock, flags); + iowrite32(mask, pctrl->gpio_base + WPCM450_GPEVST); + spin_unlock_irqrestore(&pctrl->lock, flags); +} + +static void wpcm450_gpio_irq_mask(struct irq_data *d) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(irq_data_get_irq_chip_data(d)); + int mask = event_bitmask(d->hwirq); + unsigned long flags; + u32 even; + + if (mask < 0) + return; + + spin_lock_irqsave(&pctrl->lock, flags); + even = ioread32(pctrl->gpio_base + WPCM450_GPEVEN); + even &= ~mask; + iowrite32(even, pctrl->gpio_base + WPCM450_GPEVEN); + spin_unlock_irqrestore(&pctrl->lock, flags); +} + +static void wpcm450_gpio_irq_unmask(struct irq_data *d) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(irq_data_get_irq_chip_data(d)); + int mask = event_bitmask(d->hwirq); + unsigned long flags; + u32 even; + + if (mask < 0) + return; + + spin_lock_irqsave(&pctrl->lock, flags); + even = ioread32(pctrl->gpio_base + WPCM450_GPEVEN); + even |= mask; + iowrite32(even, pctrl->gpio_base + WPCM450_GPEVEN); + spin_unlock_irqrestore(&pctrl->lock, flags); +} + +static void wpcm450_gpio_fix_evpol(struct wpcm450_pinctrl *pctrl, unsigned long all) +{ + int bitnum; + + for_each_set_bit(bitnum, &all, 32) { + int gpio = event_bitnum_to_gpio(bitnum); + u32 mask = BIT(bitnum), evpol; + int level; + + do { + evpol = ioread32(pctrl->gpio_base + WPCM450_GPEVPOL); + level = wpcm450_gpio_get(&pctrl->gc, gpio); + + /* Switch event polarity to the opposite of the current level */ + if (level) + evpol &= ~mask; + else + evpol |= mask; + + iowrite32(evpol, pctrl->gpio_base + WPCM450_GPEVPOL); + } while (wpcm450_gpio_get(&pctrl->gc, gpio) != level); + } +} + +static int wpcm450_gpio_set_irq_type(struct irq_data *d, unsigned int flow_type) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(irq_data_get_irq_chip_data(d)); + int mask = event_bitmask(d->hwirq); + unsigned long flags; + u32 evtype, evpol; + int ret = 0; + + if (mask < 0) + return mask; + + spin_lock_irqsave(&pctrl->lock, flags); + evtype = ioread32(pctrl->gpio_base + WPCM450_GPEVTYPE); + evpol = ioread32(pctrl->gpio_base + WPCM450_GPEVPOL); + pctrl->both_edges &= ~mask; + switch (flow_type) { + case IRQ_TYPE_LEVEL_LOW: + evtype |= mask; + evpol &= ~mask; + break; + case IRQ_TYPE_LEVEL_HIGH: + evtype |= mask; + evpol |= mask; + break; + case IRQ_TYPE_EDGE_FALLING: + evtype &= ~mask; + evpol &= ~mask; + break; + case IRQ_TYPE_EDGE_RISING: + evtype &= ~mask; + evpol |= mask; + break; + case IRQ_TYPE_EDGE_BOTH: + evtype &= ~mask; + pctrl->both_edges |= mask; + break; + default: + ret = -EINVAL; + } + iowrite32(evtype, pctrl->gpio_base + WPCM450_GPEVTYPE); + iowrite32(evpol, pctrl->gpio_base + WPCM450_GPEVPOL); + + /* clear the event status for good measure */ + iowrite32(mask, pctrl->gpio_base + WPCM450_GPEVST); + + /* fix event polarity after clearing event status */ + wpcm450_gpio_fix_evpol(pctrl, mask); + + spin_unlock_irqrestore(&pctrl->lock, flags); + + return ret; +} + +static const struct irq_chip wpcm450_gpio_irqchip = { + .name = "WPCM450-GPIO-IRQ", + .irq_ack = wpcm450_gpio_irq_ack, + .irq_unmask = wpcm450_gpio_irq_unmask, + .irq_mask = wpcm450_gpio_irq_mask, + .irq_set_type = wpcm450_gpio_set_irq_type, +}; + +static void wpcm450_gpio_irqhandler(struct irq_desc *desc) +{ + struct wpcm450_pinctrl *pctrl = gpiochip_get_data(irq_desc_get_handler_data(desc)); + struct irq_chip *chip = irq_desc_get_chip(desc); + unsigned long pending; + unsigned long flags; + int bitnum; + + spin_lock_irqsave(&pctrl->lock, flags); + + pending = ioread32(pctrl->gpio_base + WPCM450_GPEVST); + pending &= ioread32(pctrl->gpio_base + WPCM450_GPEVEN); + + if (pending & pctrl->both_edges) + wpcm450_gpio_fix_evpol(pctrl, pending & pctrl->both_edges); + + spin_unlock_irqrestore(&pctrl->lock, flags); + + chained_irq_enter(chip, desc); + for_each_set_bit(bitnum, &pending, 32) { + int gpio = event_bitnum_to_gpio(bitnum); + int irq = irq_find_mapping(pctrl->gc.irq.domain, gpio); + + generic_handle_irq(irq); + } + chained_irq_exit(chip, desc); +} + +/* pinmux handing */ + +static const int smb0_pins[] = { 115, 114 }; +static const int smb1_pins[] = { 117, 116 }; +static const int smb2_pins[] = { 119, 118 }; +static const int smb3_pins[] = { 30, 31 }; +static const int smb4_pins[] = { 28, 29 }; +static const int smb5_pins[] = { 26, 27 }; + +static const int scs1_pins[] = { 32 }; +static const int scs2_pins[] = { 33 }; +static const int scs3_pins[] = { 34 }; + +static const int bsp_pins[] = { 41, 42 }; +static const int hsp1_pins[] = { 43, 44, 45, 46, 47, 61, 62, 63 }; +static const int hsp2_pins[] = { 48, 49, 50, 51, 52, 53, 54, 55 }; + +static const int r1err_pins[] = { 56 }; +static const int r1md_pins[] = { 57, 58 }; +static const int rmii2_pins[] = { 84, 85, 86, 87, 88, 89 }; +static const int r2err_pins[] = { 90 }; +static const int r2md_pins[] = { 91, 92 }; + +static const int kbcc_pins[] = { 94, 93 }; +static const int clko_pins[] = { 96 }; +static const int smi_pins[] = { 97 }; +static const int uinc_pins[] = { 19 }; +static const int mben_pins[] = {}; + +static const int gspi_pins[] = { 12, 13, 14, 15 }; +static const int sspi_pins[] = { 12, 13, 14, 15 }; + +static const int xcs1_pins[] = { 35 }; +static const int xcs2_pins[] = { 36 }; + +static const int sdio_pins[] = { 7, 22, 43, 44, 45, 46, 47, 60 }; + +static const int fi0_pins[] = { 64 }; +static const int fi1_pins[] = { 65 }; +static const int fi2_pins[] = { 66 }; +static const int fi3_pins[] = { 67 }; +static const int fi4_pins[] = { 68 }; +static const int fi5_pins[] = { 69 }; +static const int fi6_pins[] = { 70 }; +static const int fi7_pins[] = { 71 }; +static const int fi8_pins[] = { 72 }; +static const int fi9_pins[] = { 73 }; +static const int fi10_pins[] = { 74 }; +static const int fi11_pins[] = { 75 }; +static const int fi12_pins[] = { 76 }; +static const int fi13_pins[] = { 77 }; +static const int fi14_pins[] = { 78 }; +static const int fi15_pins[] = { 79 }; + +static const int pwm0_pins[] = { 80 }; +static const int pwm1_pins[] = { 81 }; +static const int pwm2_pins[] = { 82 }; +static const int pwm3_pins[] = { 83 }; +static const int pwm4_pins[] = { 20 }; +static const int pwm5_pins[] = { 21 }; +static const int pwm6_pins[] = { 16 }; +static const int pwm7_pins[] = { 17 }; + +static const int hg0_pins[] = { 20 }; +static const int hg1_pins[] = { 21 }; +static const int hg2_pins[] = { 22 }; +static const int hg3_pins[] = { 23 }; +static const int hg4_pins[] = { 24 }; +static const int hg5_pins[] = { 25 }; +static const int hg6_pins[] = { 59 }; +static const int hg7_pins[] = { 60 }; + +/* + * pin: name, number + * group: name, npins, pins + * function: name, ngroups, groups + */ +struct wpcm450_group { + const char *name; + const unsigned int *pins; + int npins; +}; + +#define WPCM450_GRPS \ + WPCM450_GRP(smb3), \ + WPCM450_GRP(smb4), \ + WPCM450_GRP(smb5), \ + WPCM450_GRP(scs1), \ + WPCM450_GRP(scs2), \ + WPCM450_GRP(scs3), \ + WPCM450_GRP(smb0), \ + WPCM450_GRP(smb1), \ + WPCM450_GRP(smb2), \ + WPCM450_GRP(bsp), \ + WPCM450_GRP(hsp1), \ + WPCM450_GRP(hsp2), \ + WPCM450_GRP(r1err), \ + WPCM450_GRP(r1md), \ + WPCM450_GRP(rmii2), \ + WPCM450_GRP(r2err), \ + WPCM450_GRP(r2md), \ + WPCM450_GRP(kbcc), \ + WPCM450_GRP(clko), \ + WPCM450_GRP(smi), \ + WPCM450_GRP(uinc), \ + WPCM450_GRP(gspi), \ + WPCM450_GRP(mben), \ + WPCM450_GRP(xcs2), \ + WPCM450_GRP(xcs1), \ + WPCM450_GRP(sdio), \ + WPCM450_GRP(sspi), \ + WPCM450_GRP(fi0), \ + WPCM450_GRP(fi1), \ + WPCM450_GRP(fi2), \ + WPCM450_GRP(fi3), \ + WPCM450_GRP(fi4), \ + WPCM450_GRP(fi5), \ + WPCM450_GRP(fi6), \ + WPCM450_GRP(fi7), \ + WPCM450_GRP(fi8), \ + WPCM450_GRP(fi9), \ + WPCM450_GRP(fi10), \ + WPCM450_GRP(fi11), \ + WPCM450_GRP(fi12), \ + WPCM450_GRP(fi13), \ + WPCM450_GRP(fi14), \ + WPCM450_GRP(fi15), \ + WPCM450_GRP(pwm0), \ + WPCM450_GRP(pwm1), \ + WPCM450_GRP(pwm2), \ + WPCM450_GRP(pwm3), \ + WPCM450_GRP(pwm4), \ + WPCM450_GRP(pwm5), \ + WPCM450_GRP(pwm6), \ + WPCM450_GRP(pwm7), \ + WPCM450_GRP(hg0), \ + WPCM450_GRP(hg1), \ + WPCM450_GRP(hg2), \ + WPCM450_GRP(hg3), \ + WPCM450_GRP(hg4), \ + WPCM450_GRP(hg5), \ + WPCM450_GRP(hg6), \ + WPCM450_GRP(hg7), \ + +enum { +#define WPCM450_GRP(x) fn_ ## x + WPCM450_GRPS + /* add placeholder for none/gpio */ + WPCM450_GRP(none), + WPCM450_GRP(gpio), +#undef WPCM450_GRP +}; + +static struct wpcm450_group wpcm450_groups[] = { +#define WPCM450_GRP(x) { .name = #x, .pins = x ## _pins, \ + .npins = ARRAY_SIZE(x ## _pins) } + WPCM450_GRPS +#undef WPCM450_GRP +}; + +#define WPCM450_SFUNC(a) WPCM450_FUNC(a, #a) +#define WPCM450_FUNC(a, b...) static const char *a ## _grp[] = { b } +#define WPCM450_MKFUNC(nm) { .name = #nm, .ngroups = ARRAY_SIZE(nm ## _grp), \ + .groups = nm ## _grp } +struct wpcm450_func { + const char *name; + const unsigned int ngroups; + const char *const *groups; +}; + +WPCM450_SFUNC(smb3); +WPCM450_SFUNC(smb4); +WPCM450_SFUNC(smb5); +WPCM450_SFUNC(scs1); +WPCM450_SFUNC(scs2); +WPCM450_SFUNC(scs3); +WPCM450_SFUNC(smb0); +WPCM450_SFUNC(smb1); +WPCM450_SFUNC(smb2); +WPCM450_SFUNC(bsp); +WPCM450_SFUNC(hsp1); +WPCM450_SFUNC(hsp2); +WPCM450_SFUNC(r1err); +WPCM450_SFUNC(r1md); +WPCM450_SFUNC(rmii2); +WPCM450_SFUNC(r2err); +WPCM450_SFUNC(r2md); +WPCM450_SFUNC(kbcc); +WPCM450_SFUNC(clko); +WPCM450_SFUNC(smi); +WPCM450_SFUNC(uinc); +WPCM450_SFUNC(gspi); +WPCM450_SFUNC(mben); +WPCM450_SFUNC(xcs2); +WPCM450_SFUNC(xcs1); +WPCM450_SFUNC(sdio); +WPCM450_SFUNC(sspi); +WPCM450_SFUNC(fi0); +WPCM450_SFUNC(fi1); +WPCM450_SFUNC(fi2); +WPCM450_SFUNC(fi3); +WPCM450_SFUNC(fi4); +WPCM450_SFUNC(fi5); +WPCM450_SFUNC(fi6); +WPCM450_SFUNC(fi7); +WPCM450_SFUNC(fi8); +WPCM450_SFUNC(fi9); +WPCM450_SFUNC(fi10); +WPCM450_SFUNC(fi11); +WPCM450_SFUNC(fi12); +WPCM450_SFUNC(fi13); +WPCM450_SFUNC(fi14); +WPCM450_SFUNC(fi15); +WPCM450_SFUNC(pwm0); +WPCM450_SFUNC(pwm1); +WPCM450_SFUNC(pwm2); +WPCM450_SFUNC(pwm3); +WPCM450_SFUNC(pwm4); +WPCM450_SFUNC(pwm5); +WPCM450_SFUNC(pwm6); +WPCM450_SFUNC(pwm7); +WPCM450_SFUNC(hg0); +WPCM450_SFUNC(hg1); +WPCM450_SFUNC(hg2); +WPCM450_SFUNC(hg3); +WPCM450_SFUNC(hg4); +WPCM450_SFUNC(hg5); +WPCM450_SFUNC(hg6); +WPCM450_SFUNC(hg7); + +/* Function names */ +static struct wpcm450_func wpcm450_funcs[] = { + WPCM450_MKFUNC(smb3), + WPCM450_MKFUNC(smb4), + WPCM450_MKFUNC(smb5), + WPCM450_MKFUNC(scs1), + WPCM450_MKFUNC(scs2), + WPCM450_MKFUNC(scs3), + WPCM450_MKFUNC(smb0), + WPCM450_MKFUNC(smb1), + WPCM450_MKFUNC(smb2), + WPCM450_MKFUNC(bsp), + WPCM450_MKFUNC(hsp1), + WPCM450_MKFUNC(hsp2), + WPCM450_MKFUNC(r1err), + WPCM450_MKFUNC(r1md), + WPCM450_MKFUNC(rmii2), + WPCM450_MKFUNC(r2err), + WPCM450_MKFUNC(r2md), + WPCM450_MKFUNC(kbcc), + WPCM450_MKFUNC(clko), + WPCM450_MKFUNC(smi), + WPCM450_MKFUNC(uinc), + WPCM450_MKFUNC(gspi), + WPCM450_MKFUNC(mben), + WPCM450_MKFUNC(xcs2), + WPCM450_MKFUNC(xcs1), + WPCM450_MKFUNC(sdio), + WPCM450_MKFUNC(sspi), + WPCM450_MKFUNC(fi0), + WPCM450_MKFUNC(fi1), + WPCM450_MKFUNC(fi2), + WPCM450_MKFUNC(fi3), + WPCM450_MKFUNC(fi4), + WPCM450_MKFUNC(fi5), + WPCM450_MKFUNC(fi6), + WPCM450_MKFUNC(fi7), + WPCM450_MKFUNC(fi8), + WPCM450_MKFUNC(fi9), + WPCM450_MKFUNC(fi10), + WPCM450_MKFUNC(fi11), + WPCM450_MKFUNC(fi12), + WPCM450_MKFUNC(fi13), + WPCM450_MKFUNC(fi14), + WPCM450_MKFUNC(fi15), + WPCM450_MKFUNC(pwm0), + WPCM450_MKFUNC(pwm1), + WPCM450_MKFUNC(pwm2), + WPCM450_MKFUNC(pwm3), + WPCM450_MKFUNC(pwm4), + WPCM450_MKFUNC(pwm5), + WPCM450_MKFUNC(pwm6), + WPCM450_MKFUNC(pwm7), + WPCM450_MKFUNC(hg0), + WPCM450_MKFUNC(hg1), + WPCM450_MKFUNC(hg2), + WPCM450_MKFUNC(hg3), + WPCM450_MKFUNC(hg4), + WPCM450_MKFUNC(hg5), + WPCM450_MKFUNC(hg6), + WPCM450_MKFUNC(hg7), +}; + +#define WPCM450_PINCFG(a, b, c, d, e, f, g) \ + [a] { .fn0 = fn_ ## b, .reg0 = WPCM450_GCR_ ## c, .bit0 = d, \ + .fn1 = fn_ ## e, .reg1 = WPCM450_GCR_ ## f, .bit1 = g } + +struct wpcm450_pincfg { + int fn0, reg0, bit0; + int fn1, reg1, bit1; +}; + +static const struct wpcm450_pincfg pincfg[] = { + /* PIN FUNCTION 1 FUNCTION 2 */ + WPCM450_PINCFG(0, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(1, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(2, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(3, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(4, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(5, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(6, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(7, none, NONE, 0, sdio, MFSEL1, 30), + WPCM450_PINCFG(8, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(9, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(10, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(11, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(12, gspi, MFSEL1, 24, sspi, MFSEL1, 31), + WPCM450_PINCFG(13, gspi, MFSEL1, 24, sspi, MFSEL1, 31), + WPCM450_PINCFG(14, gspi, MFSEL1, 24, sspi, MFSEL1, 31), + WPCM450_PINCFG(15, gspi, MFSEL1, 24, sspi, MFSEL1, 31), + WPCM450_PINCFG(16, none, NONE, 0, pwm6, MFSEL2, 22), + WPCM450_PINCFG(17, none, NONE, 0, pwm7, MFSEL2, 23), + WPCM450_PINCFG(18, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(19, uinc, MFSEL1, 23, none, NONE, 0), + WPCM450_PINCFG(20, hg0, MFSEL2, 24, pwm4, MFSEL2, 20), + WPCM450_PINCFG(21, hg1, MFSEL2, 25, pwm5, MFSEL2, 21), + WPCM450_PINCFG(22, hg2, MFSEL2, 26, none, NONE, 0), + WPCM450_PINCFG(23, hg3, MFSEL2, 27, none, NONE, 0), + WPCM450_PINCFG(24, hg4, MFSEL2, 28, none, NONE, 0), + WPCM450_PINCFG(25, hg5, MFSEL2, 29, none, NONE, 0), + WPCM450_PINCFG(26, smb5, MFSEL1, 2, none, NONE, 0), + WPCM450_PINCFG(27, smb5, MFSEL1, 2, none, NONE, 0), + WPCM450_PINCFG(28, smb4, MFSEL1, 1, none, NONE, 0), + WPCM450_PINCFG(29, smb4, MFSEL1, 1, none, NONE, 0), + WPCM450_PINCFG(30, smb3, MFSEL1, 0, none, NONE, 0), + WPCM450_PINCFG(31, smb3, MFSEL1, 0, none, NONE, 0), + + WPCM450_PINCFG(32, scs1, MFSEL1, 3, none, NONE, 0), + WPCM450_PINCFG(33, scs2, MFSEL1, 4, none, NONE, 0), + WPCM450_PINCFG(34, scs3, MFSEL1, 5, none, NONE, 0), + WPCM450_PINCFG(35, xcs1, MFSEL1, 29, none, NONE, 0), + WPCM450_PINCFG(36, xcs2, MFSEL1, 28, none, NONE, 0), + WPCM450_PINCFG(37, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(38, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(39, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(40, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(41, bsp, MFSEL1, 9, none, NONE, 0), + WPCM450_PINCFG(42, bsp, MFSEL1, 9, none, NONE, 0), + WPCM450_PINCFG(43, hsp1, MFSEL1, 10, sdio, MFSEL1, 30), + WPCM450_PINCFG(44, hsp1, MFSEL1, 10, sdio, MFSEL1, 30), + WPCM450_PINCFG(45, hsp1, MFSEL1, 10, sdio, MFSEL1, 30), + WPCM450_PINCFG(46, hsp1, MFSEL1, 10, sdio, MFSEL1, 30), + WPCM450_PINCFG(47, hsp1, MFSEL1, 10, sdio, MFSEL1, 30), + WPCM450_PINCFG(48, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(49, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(50, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(51, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(52, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(53, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(54, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(55, hsp2, MFSEL1, 11, none, NONE, 0), + WPCM450_PINCFG(56, r1err, MFSEL1, 12, none, NONE, 0), + WPCM450_PINCFG(57, r1md, MFSEL1, 13, none, NONE, 0), + WPCM450_PINCFG(58, r1md, MFSEL1, 13, none, NONE, 0), + WPCM450_PINCFG(59, hg6, MFSEL2, 30, none, NONE, 0), + WPCM450_PINCFG(60, hg7, MFSEL2, 31, sdio, MFSEL1, 30), + WPCM450_PINCFG(61, hsp1, MFSEL1, 10, none, NONE, 0), + WPCM450_PINCFG(62, hsp1, MFSEL1, 10, none, NONE, 0), + WPCM450_PINCFG(63, hsp1, MFSEL1, 10, none, NONE, 0), + + WPCM450_PINCFG(64, fi0, MFSEL2, 0, none, NONE, 0), + WPCM450_PINCFG(65, fi1, MFSEL2, 1, none, NONE, 0), + WPCM450_PINCFG(66, fi2, MFSEL2, 2, none, NONE, 0), + WPCM450_PINCFG(67, fi3, MFSEL2, 3, none, NONE, 0), + WPCM450_PINCFG(68, fi4, MFSEL2, 4, none, NONE, 0), + WPCM450_PINCFG(69, fi5, MFSEL2, 5, none, NONE, 0), + WPCM450_PINCFG(70, fi6, MFSEL2, 6, none, NONE, 0), + WPCM450_PINCFG(71, fi7, MFSEL2, 7, none, NONE, 0), + WPCM450_PINCFG(72, fi8, MFSEL2, 8, none, NONE, 0), + WPCM450_PINCFG(73, fi9, MFSEL2, 9, none, NONE, 0), + WPCM450_PINCFG(74, fi10, MFSEL2, 10, none, NONE, 0), + WPCM450_PINCFG(75, fi11, MFSEL2, 11, none, NONE, 0), + WPCM450_PINCFG(76, fi12, MFSEL2, 12, none, NONE, 0), + WPCM450_PINCFG(77, fi13, MFSEL2, 13, none, NONE, 0), + WPCM450_PINCFG(78, fi14, MFSEL2, 14, none, NONE, 0), + WPCM450_PINCFG(79, fi15, MFSEL2, 15, none, NONE, 0), + WPCM450_PINCFG(80, pwm0, MFSEL2, 16, none, NONE, 0), + WPCM450_PINCFG(81, pwm1, MFSEL2, 17, none, NONE, 0), + WPCM450_PINCFG(82, pwm2, MFSEL2, 18, none, NONE, 0), + WPCM450_PINCFG(83, pwm3, MFSEL2, 19, none, NONE, 0), + WPCM450_PINCFG(84, rmii2, MFSEL1, 14, none, NONE, 0), + WPCM450_PINCFG(85, rmii2, MFSEL1, 14, none, NONE, 0), + WPCM450_PINCFG(86, rmii2, MFSEL1, 14, none, NONE, 0), + WPCM450_PINCFG(87, rmii2, MFSEL1, 14, none, NONE, 0), + WPCM450_PINCFG(88, rmii2, MFSEL1, 14, none, NONE, 0), + WPCM450_PINCFG(89, rmii2, MFSEL1, 14, none, NONE, 0), + WPCM450_PINCFG(90, r2err, MFSEL1, 15, none, NONE, 0), + WPCM450_PINCFG(91, r2md, MFSEL1, 16, none, NONE, 0), + WPCM450_PINCFG(92, r2md, MFSEL1, 16, none, NONE, 0), + WPCM450_PINCFG(93, kbcc, MFSEL1, 17, none, NONE, 0), + WPCM450_PINCFG(94, kbcc, MFSEL1, 17, none, NONE, 0), + WPCM450_PINCFG(95, none, NONE, 0, none, NONE, 0), + + WPCM450_PINCFG(96, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(97, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(98, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(99, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(100, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(101, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(102, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(103, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(104, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(105, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(106, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(107, none, NONE, 0, none, NONE, 0), + WPCM450_PINCFG(108, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(109, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(110, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(111, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(112, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(113, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(114, smb0, MFSEL1, 6, none, NONE, 0), + WPCM450_PINCFG(115, smb0, MFSEL1, 6, none, NONE, 0), + WPCM450_PINCFG(116, smb1, MFSEL1, 7, none, NONE, 0), + WPCM450_PINCFG(117, smb1, MFSEL1, 7, none, NONE, 0), + WPCM450_PINCFG(118, smb2, MFSEL1, 8, none, NONE, 0), + WPCM450_PINCFG(119, smb2, MFSEL1, 8, none, NONE, 0), + WPCM450_PINCFG(120, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(121, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(122, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(123, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(124, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(125, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(126, none, NONE, 0, none, NONE, 0), /* DVO */ + WPCM450_PINCFG(127, none, NONE, 0, none, NONE, 0), /* DVO */ +}; + +#define WPCM450_PIN(n) PINCTRL_PIN(n, "gpio" #n) + +static const struct pinctrl_pin_desc wpcm450_pins[] = { + WPCM450_PIN(0), WPCM450_PIN(1), WPCM450_PIN(2), WPCM450_PIN(3), + WPCM450_PIN(4), WPCM450_PIN(5), WPCM450_PIN(6), WPCM450_PIN(7), + WPCM450_PIN(8), WPCM450_PIN(9), WPCM450_PIN(10), WPCM450_PIN(11), + WPCM450_PIN(12), WPCM450_PIN(13), WPCM450_PIN(14), WPCM450_PIN(15), + WPCM450_PIN(16), WPCM450_PIN(17), WPCM450_PIN(18), WPCM450_PIN(19), + WPCM450_PIN(20), WPCM450_PIN(21), WPCM450_PIN(22), WPCM450_PIN(23), + WPCM450_PIN(24), WPCM450_PIN(25), WPCM450_PIN(26), WPCM450_PIN(27), + WPCM450_PIN(28), WPCM450_PIN(29), WPCM450_PIN(30), WPCM450_PIN(31), + WPCM450_PIN(32), WPCM450_PIN(33), WPCM450_PIN(34), WPCM450_PIN(35), + WPCM450_PIN(36), WPCM450_PIN(37), WPCM450_PIN(38), WPCM450_PIN(39), + WPCM450_PIN(40), WPCM450_PIN(41), WPCM450_PIN(42), WPCM450_PIN(43), + WPCM450_PIN(44), WPCM450_PIN(45), WPCM450_PIN(46), WPCM450_PIN(47), + WPCM450_PIN(48), WPCM450_PIN(49), WPCM450_PIN(50), WPCM450_PIN(51), + WPCM450_PIN(52), WPCM450_PIN(53), WPCM450_PIN(54), WPCM450_PIN(55), + WPCM450_PIN(56), WPCM450_PIN(57), WPCM450_PIN(58), WPCM450_PIN(59), + WPCM450_PIN(60), WPCM450_PIN(61), WPCM450_PIN(62), WPCM450_PIN(63), + WPCM450_PIN(64), WPCM450_PIN(65), WPCM450_PIN(66), WPCM450_PIN(67), + WPCM450_PIN(68), WPCM450_PIN(69), WPCM450_PIN(70), WPCM450_PIN(71), + WPCM450_PIN(72), WPCM450_PIN(73), WPCM450_PIN(74), WPCM450_PIN(75), + WPCM450_PIN(76), WPCM450_PIN(77), WPCM450_PIN(78), WPCM450_PIN(79), + WPCM450_PIN(80), WPCM450_PIN(81), WPCM450_PIN(82), WPCM450_PIN(83), + WPCM450_PIN(84), WPCM450_PIN(85), WPCM450_PIN(86), WPCM450_PIN(87), + WPCM450_PIN(88), WPCM450_PIN(89), WPCM450_PIN(90), WPCM450_PIN(91), + WPCM450_PIN(92), WPCM450_PIN(93), WPCM450_PIN(94), WPCM450_PIN(95), + WPCM450_PIN(96), WPCM450_PIN(97), WPCM450_PIN(98), WPCM450_PIN(99), + WPCM450_PIN(100), WPCM450_PIN(101), WPCM450_PIN(102), WPCM450_PIN(103), + WPCM450_PIN(104), WPCM450_PIN(105), WPCM450_PIN(106), WPCM450_PIN(107), + WPCM450_PIN(108), WPCM450_PIN(109), WPCM450_PIN(110), WPCM450_PIN(111), + WPCM450_PIN(112), WPCM450_PIN(113), WPCM450_PIN(114), WPCM450_PIN(115), + WPCM450_PIN(116), WPCM450_PIN(117), WPCM450_PIN(118), WPCM450_PIN(119), + WPCM450_PIN(120), WPCM450_PIN(121), WPCM450_PIN(122), WPCM450_PIN(123), + WPCM450_PIN(124), WPCM450_PIN(125), WPCM450_PIN(126), WPCM450_PIN(127), +}; + +/* Enable mode in pin group */ +static void wpcm450_setfunc(struct regmap *gcr_regmap, const unsigned int *pin, + int npins, int mode) +{ + const struct wpcm450_pincfg *cfg; + int i; + + for (i = 0; i < npins; i++) { + cfg = &pincfg[pin[i]]; + if (mode == fn_gpio || cfg->fn0 == mode || cfg->fn1 == mode) { + if (cfg->reg0) + regmap_update_bits(gcr_regmap, cfg->reg0, + BIT(cfg->bit0), + (cfg->fn0 == mode) ? BIT(cfg->bit0) : 0); + if (cfg->reg1) + regmap_update_bits(gcr_regmap, cfg->reg1, + BIT(cfg->bit1), + (cfg->fn1 == mode) ? BIT(cfg->bit1) : 0); + } + } +} + +/* pinctrl_ops */ +static int wpcm450_get_groups_count(struct pinctrl_dev *pctldev) +{ + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); + + dev_dbg(npcm->dev, "group size: %d\n", ARRAY_SIZE(wpcm450_groups)); + return ARRAY_SIZE(wpcm450_groups); +} + +static const char *wpcm450_get_group_name(struct pinctrl_dev *pctldev, + unsigned int selector) +{ + return wpcm450_groups[selector].name; +} + +static int wpcm450_get_group_pins(struct pinctrl_dev *pctldev, + unsigned int selector, + const unsigned int **pins, + unsigned int *npins) +{ + *npins = wpcm450_groups[selector].npins; + *pins = wpcm450_groups[selector].pins; + + return 0; +} + +static int wpcm450_dt_node_to_map(struct pinctrl_dev *pctldev, + struct device_node *np_config, + struct pinctrl_map **map, + u32 *num_maps) +{ + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); + + dev_dbg(npcm->dev, "dt_node_to_map: %s\n", np_config->name); + return pinconf_generic_dt_node_to_map(pctldev, np_config, + map, num_maps, + PIN_MAP_TYPE_INVALID); +} + +static void wpcm450_dt_free_map(struct pinctrl_dev *pctldev, + struct pinctrl_map *map, u32 num_maps) +{ + kfree(map); +} + +static const struct pinctrl_ops wpcm450_pinctrl_ops = { + .get_groups_count = wpcm450_get_groups_count, + .get_group_name = wpcm450_get_group_name, + .get_group_pins = wpcm450_get_group_pins, + .dt_node_to_map = wpcm450_dt_node_to_map, + .dt_free_map = wpcm450_dt_free_map, +}; + +/* pinmux_ops */ +static int wpcm450_get_functions_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(wpcm450_funcs); +} + +static const char *wpcm450_get_function_name(struct pinctrl_dev *pctldev, + unsigned int function) +{ + return wpcm450_funcs[function].name; +} + +static int wpcm450_get_function_groups(struct pinctrl_dev *pctldev, + unsigned int function, + const char * const **groups, + unsigned int * const ngroups) +{ + *ngroups = wpcm450_funcs[function].ngroups; + *groups = wpcm450_funcs[function].groups; + + return 0; +} + +static int wpcm450_pinmux_set_mux(struct pinctrl_dev *pctldev, + unsigned int function, + unsigned int group) +{ + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); + + dev_dbg(npcm->dev, "set_mux: %d, %d[%s]\n", function, group, + wpcm450_groups[group].name); + + wpcm450_setfunc(npcm->gcr_regmap, wpcm450_groups[group].pins, + wpcm450_groups[group].npins, group); + + return 0; +} + +static int wpcm450_gpio_request_enable(struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned int offset) +{ + struct wpcm450_pinctrl *npcm = pinctrl_dev_get_drvdata(pctldev); + + if (!range) { + dev_err(npcm->dev, "invalid range\n"); + return -EINVAL; + } + if (!range->gc) { + dev_err(npcm->dev, "invalid gpiochip\n"); + return -EINVAL; + } + + wpcm450_setfunc(npcm->gcr_regmap, &offset, 1, fn_gpio); + + return 0; +} + +/* Release GPIO back to pinctrl mode */ +static void wpcm450_gpio_request_free(struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned int offset) +{ + struct wpcm450_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); + int virq; + + virq = irq_find_mapping(pctrl->domain, offset); + if (virq) + irq_dispose_mapping(virq); +} + +static const struct pinmux_ops wpcm450_pinmux_ops = { + .get_functions_count = wpcm450_get_functions_count, + .get_function_name = wpcm450_get_function_name, + .get_function_groups = wpcm450_get_function_groups, + .set_mux = wpcm450_pinmux_set_mux, + .gpio_request_enable = wpcm450_gpio_request_enable, + .gpio_disable_free = wpcm450_gpio_request_free, +}; + +/* pinconf_ops */ +static int debounce_bitmask(int gpio) +{ + if (gpio >= 0 && gpio < 16) + return BIT(gpio); + return -EINVAL; +} + +static int wpcm450_config_get(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *config) +{ + struct wpcm450_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param = pinconf_to_config_param(*config); + unsigned long flags; + int mask; + u32 reg; + + switch (param) { + case PIN_CONFIG_INPUT_DEBOUNCE: + mask = debounce_bitmask(pin); + if (mask < 0) + return mask; + + spin_lock_irqsave(&pctrl->lock, flags); + reg = ioread32(pctrl->gpio_base + WPCM450_GPEVDBNC); + spin_unlock_irqrestore(&pctrl->lock, flags); + + *config = pinconf_to_config_packed(param, !!(reg & mask)); + break; + default: + return -ENOTSUPP; + } + + return 0; +} + +static int wpcm450_config_set_one(struct wpcm450_pinctrl *pctrl, + unsigned int pin, unsigned long config) +{ + enum pin_config_param param = pinconf_to_config_param(config); + unsigned long flags; + int mask; + u32 reg; + int arg; + + switch (param) { + case PIN_CONFIG_INPUT_DEBOUNCE: + mask = event_bitmask(pin); + if (mask < 0) + return mask; + + arg = pinconf_to_config_argument(config); + + spin_lock_irqsave(&pctrl->lock, flags); + reg = ioread32(pctrl->gpio_base + WPCM450_GPEVDBNC); + if (arg) + reg |= mask; + else + reg &= ~mask; + iowrite32(reg, pctrl->gpio_base + WPCM450_GPEVDBNC); + spin_unlock_irqrestore(&pctrl->lock, flags); + break; + default: + return -ENOTSUPP; + } + + return 0; +} + +/* Set multiple configuration settings for a pin */ +static int wpcm450_config_set(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *configs, unsigned int num_configs) +{ + struct wpcm450_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); + int rc; + + while (num_configs--) { + rc = wpcm450_config_set_one(pctrl, pin, *configs++); + if (rc) + return rc; + } + + return 0; +} + +static const struct pinconf_ops wpcm450_pinconf_ops = { + .is_generic = true, + .pin_config_get = wpcm450_config_get, + .pin_config_set = wpcm450_config_set, +}; + +static struct pinctrl_desc wpcm450_pinctrl_desc = { + .name = "wpcm450-pinctrl", + .pins = wpcm450_pins, + .npins = ARRAY_SIZE(wpcm450_pins), + .pctlops = &wpcm450_pinctrl_ops, + .pmxops = &wpcm450_pinmux_ops, + .confops = &wpcm450_pinconf_ops, + .owner = THIS_MODULE, +}; + +static int wpcm450_gpio_register(struct wpcm450_pinctrl *pctrl) +{ + struct device_node *np = pctrl->dev->of_node; + struct gpio_irq_chip *girq; + int ret; + int i; + + if (!of_find_property(np, "gpio-controller", NULL)) + return -ENODEV; + + pctrl->gpio_base = of_iomap(np, 0); + if (!pctrl->gpio_base) { + dev_err(pctrl->dev, "Resource fail for GPIO controller\n"); + return -ENOMEM; + } + + pctrl->gc.label = dev_name(pctrl->dev); + pctrl->gc.owner = THIS_MODULE; + pctrl->gc.parent = pctrl->dev; + + pctrl->gc.get_direction = wpcm450_gpio_get_direction; + pctrl->gc.direction_input = wpcm450_gpio_direction_input; + pctrl->gc.direction_output = wpcm450_gpio_direction_output; + pctrl->gc.get = wpcm450_gpio_get; + pctrl->gc.set = wpcm450_gpio_set; + + pctrl->gc.base = -1; + pctrl->gc.ngpio = WPCM450_NUM_GPIOS; + pctrl->gc.can_sleep = false; + + pctrl->irqc = wpcm450_gpio_irqchip; + girq = &pctrl->gc.irq; + girq->chip = &pctrl->irqc; + girq->parent_handler = wpcm450_gpio_irqhandler; + girq->num_parents = WPCM450_NUM_GPIO_IRQS; + girq->parents = devm_kcalloc(pctrl->dev, WPCM450_NUM_GPIO_IRQS, + sizeof(*girq->parents), GFP_KERNEL); + if (!girq->parents) + return -ENOMEM; + girq->default_type = IRQ_TYPE_NONE; + girq->handler = handle_level_irq; + + for (i = 0; i < WPCM450_NUM_GPIO_IRQS; i++) { + int irq = irq_of_parse_and_map(np, i); + + if (irq < 0) { + dev_err(pctrl->dev, "No IRQ for GPIO controller\n"); + return irq; + } + girq->parents[i] = irq; + } + + ret = devm_gpiochip_add_data(pctrl->dev, &pctrl->gc, pctrl); + if (ret) { + dev_err(pctrl->dev, "Failed to add GPIO chip: %d\n", ret); + return ret; + } + + return 0; +} + +static int wpcm450_pinctrl_probe(struct platform_device *pdev) +{ + struct wpcm450_pinctrl *pctrl; + int ret; + + pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL); + if (!pctrl) + return -ENOMEM; + + pctrl->dev = &pdev->dev; + spin_lock_init(&pctrl->lock); + dev_set_drvdata(&pdev->dev, pctrl); + + pctrl->gcr_regmap = + syscon_regmap_lookup_by_compatible("nuvoton,wpcm450-gcr"); + if (IS_ERR(pctrl->gcr_regmap)) { + dev_err(pctrl->dev, "didn't find nuvoton,wpcm450-gcr\n"); + return PTR_ERR(pctrl->gcr_regmap); + } + + pctrl->pctldev = devm_pinctrl_register(&pdev->dev, + &wpcm450_pinctrl_desc, pctrl); + if (IS_ERR(pctrl->pctldev)) { + dev_err(&pdev->dev, "Failed to register pinctrl device\n"); + return PTR_ERR(pctrl->pctldev); + } + + ret = wpcm450_gpio_register(pctrl); + if (ret < 0) + return ret; + + pr_info("WPCM450 pinctrl and GPIO driver probed\n"); + return 0; +} + +static const struct of_device_id wpcm450_pinctrl_match[] = { + { .compatible = "nuvoton,wpcm450-pinctrl" }, + { }, +}; +MODULE_DEVICE_TABLE(of, wpcm450_pinctrl_match); + +static struct platform_driver wpcm450_pinctrl_driver = { + .probe = wpcm450_pinctrl_probe, + .driver = { + .name = "wpcm450-pinctrl", + .of_match_table = wpcm450_pinctrl_match, + .suppress_bind_attrs = true, + }, +}; + +static int __init wpcm450_pinctrl_register(void) +{ + return platform_driver_register(&wpcm450_pinctrl_driver); +} +arch_initcall(wpcm450_pinctrl_register); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Jonathan Neuschäfer <j.neuschaefer@gmx.net>"); +MODULE_DESCRIPTION("Nuvoton WPCM450 Pinctrl and GPIO driver");
This driver is heavily based on the one for NPCM7xx, because the WPCM450 is a predecessor of those SoCs. The biggest difference is in how the GPIO controller works. In the WPCM450, the GPIO registers are not organized in multiple banks, but rather placed continually into the same register block, and the driver reflects this. Some functionality implemented in the hardware was (for now) left unused in the driver, specifically blinking and pull-up/down. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> --- This patch has a few checkpatch warnings, which are inherited from the pinctrl-npcm7xx driver. I decided to ignore those. Specifically: (1) the Kconfig help text is considered too short; (2) WPCM450_GRPS is an unwrapped list; (3) use of -ENOTSUPP is discouraged. --- MAINTAINERS | 1 + drivers/pinctrl/Makefile | 2 +- drivers/pinctrl/nuvoton/Kconfig | 14 + drivers/pinctrl/nuvoton/Makefile | 1 + drivers/pinctrl/nuvoton/pinctrl-wpcm450.c | 1230 +++++++++++++++++++++ 5 files changed, 1247 insertions(+), 1 deletion(-) create mode 100644 drivers/pinctrl/nuvoton/pinctrl-wpcm450.c -- 2.30.2