@@ -439,6 +439,8 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)
ocelot->vcap_is2_actions= felix->info->vcap_is2_actions;
ocelot->vcap = felix->info->vcap;
ocelot->ops = felix->info->ops;
+ ocelot->inj_prefix = OCELOT_TAG_PREFIX_NONE;
+ ocelot->xtr_prefix = OCELOT_TAG_PREFIX_LONG;
port_phy_modes = kcalloc(num_phys_ports, sizeof(phy_interface_t),
GFP_KERNEL);
@@ -538,6 +540,28 @@ static int felix_init_structs(struct felix *felix, int num_phys_ports)
return 0;
}
+/* The CPU port module is connected to the Node Processor Interface (NPI). This
+ * is the mode through which frames can be injected from and extracted to an
+ * external CPU, over Ethernet.
+ */
+static void felix_npi_port_init(struct ocelot *ocelot, int port)
+{
+ ocelot->npi = port;
+
+ ocelot_write(ocelot, QSYS_EXT_CPU_CFG_EXT_CPUQ_MSK_M |
+ QSYS_EXT_CPU_CFG_EXT_CPU_PORT(port),
+ QSYS_EXT_CPU_CFG);
+
+ /* NPI port Injection/Extraction configuration */
+ ocelot_fields_write(ocelot, port, SYS_PORT_MODE_INCL_XTR_HDR,
+ ocelot->xtr_prefix);
+ ocelot_fields_write(ocelot, port, SYS_PORT_MODE_INCL_INJ_HDR,
+ ocelot->inj_prefix);
+
+ /* Disable transmission of pause frames */
+ ocelot_fields_write(ocelot, port, SYS_PAUSE_CFG_PAUSE_ENA, 0);
+}
+
/* Hardware initialization done here so that we can allocate structures with
* devm without fear of dsa_register_switch returning -EPROBE_DEFER and causing
* us to allocate structures twice (leak memory) and map PCI memory twice
@@ -570,11 +594,8 @@ static int felix_setup(struct dsa_switch *ds)
for (port = 0; port < ds->num_ports; port++) {
ocelot_init_port(ocelot, port);
- /* Bring up the CPU port module and configure the NPI port */
if (dsa_is_cpu_port(ds, port))
- ocelot_configure_cpu(ocelot, port,
- OCELOT_TAG_PREFIX_NONE,
- OCELOT_TAG_PREFIX_LONG);
+ felix_npi_port_init(ocelot, port);
/* Set the default QoS Classification based on PCP and DEI
* bits of vlan tag.
@@ -1346,22 +1346,14 @@ void ocelot_init_port(struct ocelot *ocelot, int port)
}
EXPORT_SYMBOL(ocelot_init_port);
-/* Configure and enable the CPU port module, which is a set of queues.
- * If @npi contains a valid port index, the CPU port module is connected
- * to the Node Processor Interface (NPI). This is the mode through which
- * frames can be injected from and extracted to an external CPU,
- * over Ethernet.
+/* Configure and enable the CPU port module, which is a set of queues
+ * accessible through register MMIO, frame DMA or Ethernet (in case
+ * NPI mode is used).
*/
-void ocelot_configure_cpu(struct ocelot *ocelot, int npi,
- enum ocelot_tag_prefix injection,
- enum ocelot_tag_prefix extraction)
+static void ocelot_cpu_port_init(struct ocelot *ocelot)
{
int cpu = ocelot->num_phys_ports;
- ocelot->npi = npi;
- ocelot->inj_prefix = injection;
- ocelot->xtr_prefix = extraction;
-
/* The unicast destination PGID for the CPU port module is unused */
ocelot_write_rix(ocelot, 0, ANA_PGID_PGID, cpu);
/* Instead set up a multicast destination PGID for traffic copied to
@@ -1373,31 +1365,13 @@ void ocelot_configure_cpu(struct ocelot *ocelot, int npi,
ANA_PORT_PORT_CFG_PORTID_VAL(cpu),
ANA_PORT_PORT_CFG, cpu);
- if (npi >= 0 && npi < ocelot->num_phys_ports) {
- ocelot_write(ocelot, QSYS_EXT_CPU_CFG_EXT_CPUQ_MSK_M |
- QSYS_EXT_CPU_CFG_EXT_CPU_PORT(npi),
- QSYS_EXT_CPU_CFG);
-
- /* Enable NPI port */
- ocelot_fields_write(ocelot, npi,
- QSYS_SWITCH_PORT_MODE_PORT_ENA, 1);
- /* NPI port Injection/Extraction configuration */
- ocelot_fields_write(ocelot, npi, SYS_PORT_MODE_INCL_XTR_HDR,
- extraction);
- ocelot_fields_write(ocelot, npi, SYS_PORT_MODE_INCL_INJ_HDR,
- injection);
-
- /* Disable transmission of pause frames */
- ocelot_fields_write(ocelot, npi, SYS_PAUSE_CFG_PAUSE_ENA, 0);
- }
-
/* Enable CPU port module */
ocelot_fields_write(ocelot, cpu, QSYS_SWITCH_PORT_MODE_PORT_ENA, 1);
/* CPU port Injection/Extraction configuration */
ocelot_fields_write(ocelot, cpu, SYS_PORT_MODE_INCL_XTR_HDR,
- extraction);
+ ocelot->xtr_prefix);
ocelot_fields_write(ocelot, cpu, SYS_PORT_MODE_INCL_INJ_HDR,
- injection);
+ ocelot->inj_prefix);
/* Configure the CPU port to be VLAN aware */
ocelot_write_gix(ocelot, ANA_PORT_VLAN_CFG_VLAN_VID(0) |
@@ -1405,7 +1379,6 @@ void ocelot_configure_cpu(struct ocelot *ocelot, int npi,
ANA_PORT_VLAN_CFG_VLAN_POP_CNT(1),
ANA_PORT_VLAN_CFG, cpu);
}
-EXPORT_SYMBOL(ocelot_configure_cpu);
int ocelot_init(struct ocelot *ocelot)
{
@@ -1445,6 +1418,7 @@ int ocelot_init(struct ocelot *ocelot)
ocelot_mact_init(ocelot);
ocelot_vlan_init(ocelot);
ocelot_vcap_init(ocelot);
+ ocelot_cpu_port_init(ocelot);
for (port = 0; port < ocelot->num_phys_ports; port++) {
/* Clear all counters (5 groups) */
@@ -930,10 +930,6 @@ static int mscc_ocelot_init_ports(struct platform_device *pdev,
if (!ocelot->ports)
return -ENOMEM;
- /* No NPI port */
- ocelot_configure_cpu(ocelot, -1, OCELOT_TAG_PREFIX_NONE,
- OCELOT_TAG_PREFIX_NONE);
-
for_each_available_child_of_node(ports, portnp) {
struct ocelot_port_private *priv;
struct ocelot_port *ocelot_port;
@@ -1120,6 +1116,9 @@ static int mscc_ocelot_probe(struct platform_device *pdev)
ocelot->vcap_is2_keys = vsc7514_vcap_is2_keys;
ocelot->vcap_is2_actions = vsc7514_vcap_is2_actions;
ocelot->vcap = vsc7514_vcap_props;
+ ocelot->inj_prefix = OCELOT_TAG_PREFIX_NONE;
+ ocelot->xtr_prefix = OCELOT_TAG_PREFIX_NONE;
+ ocelot->npi = -1;
err = ocelot_init(ocelot);
if (err)
@@ -672,9 +672,6 @@ void __ocelot_rmw_ix(struct ocelot *ocelot, u32 val, u32 mask, u32 reg,
int ocelot_regfields_init(struct ocelot *ocelot,
const struct reg_field *const regfields);
struct regmap *ocelot_regmap_init(struct ocelot *ocelot, struct resource *res);
-void ocelot_configure_cpu(struct ocelot *ocelot, int npi,
- enum ocelot_tag_prefix injection,
- enum ocelot_tag_prefix extraction);
int ocelot_init(struct ocelot *ocelot);
void ocelot_deinit(struct ocelot *ocelot);
void ocelot_init_port(struct ocelot *ocelot, int port);
Remove the ocelot_configure_cpu() function, which was in fact bringing up 2 ports: the CPU port module, which both switchdev and DSA have, and the NPI port, which only DSA has. The (non-Ethernet) CPU port module is at a fixed index in the analyzer, whereas the NPI port is selected through the "ethernet" property in the device tree. Therefore, the function to set up an NPI port is DSA-specific, so we move it there, simplifying the ocelot switch library a little bit. Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> --- drivers/net/dsa/ocelot/felix.c | 29 +++++++++++++--- drivers/net/ethernet/mscc/ocelot.c | 40 ++++------------------ drivers/net/ethernet/mscc/ocelot_vsc7514.c | 7 ++-- include/soc/mscc/ocelot.h | 3 -- 4 files changed, 35 insertions(+), 44 deletions(-)