@@ -658,6 +658,31 @@ static int virtnet_set_tx_csum(struct net_device *dev, u32 data)
return ethtool_op_set_tx_hw_csum(dev, data);
}
+static void virtnet_set_rx_mode(struct net_device *dev)
+{
+ struct virtnet_info *vi = netdev_priv(dev);
+ u8 promisc, allmulti;
+
+ /* we're useless without the control virtqueue */
+ if (!vi->cvq)
+ return;
+
+ promisc = ((dev->flags & IFF_PROMISC) != 0 || dev->uc_count > 0);
+ allmulti = ((dev->flags & IFF_ALLMULTI) != 0 || dev->mc_count > 0);
+
+ if (virtnet_send_command(vi, VIRTIO_NET_CTRL_RX_MODE,
+ VIRTIO_NET_CTRL_RX_MODE_PROMISC,
+ &promisc, sizeof(promisc)))
+ printk(KERN_WARNING "%s: Failed to %sable promisc mode.\n",
+ dev->name, promisc ? "en" : "dis");
+
+ if (virtnet_send_command(vi, VIRTIO_NET_CTRL_RX_MODE,
+ VIRTIO_NET_CTRL_RX_MODE_ALLMULTI,
+ &allmulti, sizeof(allmulti)))
+ printk(KERN_WARNING "%s: Failed to %sable allmulti mode.\n",
+ dev->name, allmulti ? "en" : "dis");
+}
+
static struct ethtool_ops virtnet_ethtool_ops = {
.set_tx_csum = virtnet_set_tx_csum,
.set_sg = ethtool_op_set_sg,
@@ -681,6 +706,7 @@ static const struct net_device_ops virtnet_netdev = {
.ndo_start_xmit = start_xmit,
.ndo_validate_addr = eth_validate_addr,
.ndo_set_mac_address = virtnet_set_mac_address,
+ .ndo_set_rx_mode = virtnet_set_rx_mode,
.ndo_change_mtu = virtnet_change_mtu,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = virtnet_netpoll,
@@ -770,7 +796,7 @@ static int virtnet_probe(struct virtio_device *vdev)
/*
* Outbound control channel virtqueue. We can live without it,
- * so don't go fatal if it's not there.
+ * so don't go fatal if it's not there. Required for set_rx_mode.
*/
vi->cvq = vdev->config->find_vq(vdev, 2, NULL);
if (IS_ERR(vi->cvq))
@@ -70,4 +70,13 @@ typedef __u8 virtio_net_ctrl_ack;
#define VIRTIO_NET_OK 0
#define VIRTIO_NET_ERR 1
+/*
+ * Control the RX mode, ie. promisucous and allmulti. PROMISC and
+ * ALLMULTI commands require an "out" sg entry containing a 1 byte
+ * state value, zero = disable, non-zero = enable.
+ */
+#define VIRTIO_NET_CTRL_RX_MODE 0
+ #define VIRTIO_NET_CTRL_RX_MODE_PROMISC 0
+ #define VIRTIO_NET_CTRL_RX_MODE_ALLMULTI 1
+
#endif /* _LINUX_VIRTIO_NET_H */
Make use of the RX_MODE control virtqueue class to enable the set_rx_mode netdev interface. This allows us to selectively enable/disable promiscuous and allmulti mode so we don't see packets we don't want. We'll automatically enable these as needed if additional unicast or multicast addresses are requested. Signed-off-by: Alex Williamson <alex.williamson@hp.com> --- drivers/net/virtio_net.c | 28 +++++++++++++++++++++++++++- include/linux/virtio_net.h | 9 +++++++++ 2 files changed, 36 insertions(+), 1 deletions(-) -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html