@@ -18,6 +18,9 @@
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/device.h>
+#include <linux/of.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
#include <linux/spi/spi.h>
@@ -120,7 +123,8 @@ static const struct ks8995_chip_params ks8995_chip[] = {
};
struct ks8995_pdata {
- /* not yet implemented */
+ int reset_gpio;
+ enum of_gpio_flags reset_gpio_flags;
};
struct ks8995_switch {
@@ -339,6 +343,24 @@ err_out:
return err;
}
+/* ks8995_parse_dt - setup platform data from devicetree
+ * @ks: pointer to switch instance
+ *
+ * Parses supported DT properties and sets up platform data
+ * accordingly.
+ */
+static void ks8995_parse_dt(struct ks8995_switch *ks)
+{
+ struct device_node *np = ks->spi->dev.of_node;
+ struct ks8995_pdata *pdata = ks->pdata;
+
+ if (!np)
+ return;
+
+ pdata->reset_gpio = of_get_named_gpio_flags(np, "reset-gpios", 0,
+ &pdata->reset_gpio_flags);
+}
+
static const struct bin_attribute ks8995_registers_attr = {
.attr = {
.name = "registers",
@@ -352,14 +374,10 @@ static const struct bin_attribute ks8995_registers_attr = {
/* ------------------------------------------------------------------------ */
static int ks8995_probe(struct spi_device *spi)
{
- struct ks8995_switch *ks;
- struct ks8995_pdata *pdata;
- int err;
+ struct ks8995_switch *ks;
+ int err;
int variant = spi_get_device_id(spi)->driver_data;
- /* Chip description */
- pdata = spi->dev.platform_data;
-
if (variant >= max_variant) {
dev_err(&spi->dev, "bad chip variant %d\n", variant);
return -ENODEV;
@@ -370,10 +388,42 @@ static int ks8995_probe(struct spi_device *spi)
return -ENOMEM;
mutex_init(&ks->lock);
- ks->pdata = pdata;
ks->spi = spi_dev_get(spi);
ks->chip = &ks8995_chip[variant];
+ if (ks->spi->dev.of_node) {
+ ks->pdata = devm_kzalloc(&spi->dev, sizeof(*ks->pdata),
+ GFP_KERNEL);
+ if (!ks->pdata)
+ return -ENOMEM;
+
+ ks->pdata->reset_gpio = -1;
+
+ ks8995_parse_dt(ks);
+ }
+
+ if (!ks->pdata)
+ ks->pdata = spi->dev.platform_data;
+
+ /* de-assert switch reset */
+ if (ks->pdata && gpio_is_valid(ks->pdata->reset_gpio)) {
+ unsigned long flags;
+
+ flags = (ks->pdata->reset_gpio_flags == OF_GPIO_ACTIVE_LOW ?
+ GPIOF_ACTIVE_LOW : 0);
+
+ err = devm_gpio_request_one(&spi->dev,
+ ks->pdata->reset_gpio,
+ flags, "switch-reset");
+ if (err) {
+ dev_err(&spi->dev,
+ "failed to get reset-gpios: %d\n", err);
+ return -EIO;
+ }
+
+ gpiod_set_value(gpio_to_desc(ks->pdata->reset_gpio), 0);
+ }
+
spi_set_drvdata(spi, ks);
spi->mode = SPI_MODE_0;
@@ -414,11 +464,14 @@ static int ks8995_remove(struct spi_device *spi)
sysfs_remove_bin_file(&spi->dev.kobj, &ks->regs_attr);
+ /* assert reset */
+ if (ks->pdata && gpio_is_valid(ks->pdata->reset_gpio))
+ gpiod_set_value(gpio_to_desc(ks->pdata->reset_gpio), 1);
+
return 0;
}
/* ------------------------------------------------------------------------ */
-
static struct spi_driver ks8995_driver = {
.driver = {
.name = "spi-ks8995",
When using device tree it is no more possible to reset the PHY at board level. Furthermore, doing in the driver allows to power down the switch when it is not used any more. The patch introduces a new optional property "reset-gpios" denoting an appropriate GPIO handle, e.g.: reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW> Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com> --- drivers/net/phy/spi_ks8995.c | 71 ++++++++++++++++++++++++++++++++++++++------ 1 file changed, 62 insertions(+), 9 deletions(-)