@@ -30,7 +30,7 @@ int cros_ec_prepare_tx(struct cros_ec_device *ec_dev,
uint8_t *out;
int csum, i;
- BUG_ON(msg->out_len > EC_HOST_PARAM_SIZE);
+ BUG_ON(msg->out_len > EC_PROTO2_MAX_PARAM_SIZE);
out = ec_dev->dout;
out[0] = EC_CMD_VERSION0 + msg->version;
out[1] = msg->cmd;
@@ -29,8 +29,8 @@ enum {
EC_MSG_RX_PROTO_BYTES = 3,
/* Max length of messages */
- EC_MSG_BYTES = EC_HOST_PARAM_SIZE + EC_MSG_TX_PROTO_BYTES,
-
+ EC_MSG_BYTES = EC_PROTO2_MAX_PARAM_SIZE +
+ EC_MSG_TX_PROTO_BYTES,
};
/**
@@ -24,25 +24,12 @@
#define __CROS_EC_COMMANDS_H
/*
- * Protocol overview
+ * Current version of this protocol
*
- * request: CMD [ P0 P1 P2 ... Pn S ]
- * response: ERR [ P0 P1 P2 ... Pn S ]
- *
- * where the bytes are defined as follow :
- * - CMD is the command code. (defined by EC_CMD_ constants)
- * - ERR is the error code. (defined by EC_RES_ constants)
- * - Px is the optional payload.
- * it is not sent if the error code is not success.
- * (defined by ec_params_ and ec_response_ structures)
- * - S is the checksum which is the sum of all payload bytes.
- *
- * On LPC, CMD and ERR are sent/received at EC_LPC_ADDR_KERNEL|USER_CMD
- * and the payloads are sent/received at EC_LPC_ADDR_KERNEL|USER_PARAM.
- * On I2C, all bytes are sent serially in the same message.
+ * TODO(crosbug.com/p/11223): This is effectively useless; protocol is
+ * determined in other ways. Remove this once the kernel code no longer
+ * depends on it.
*/
-
-/* Current version of this protocol */
#define EC_PROTO_VERSION 0x00000002
/* Command version mask */
@@ -57,13 +44,19 @@
#define EC_LPC_ADDR_HOST_CMD 0x204
/* I/O addresses for host command args and params */
-#define EC_LPC_ADDR_HOST_ARGS 0x800
-#define EC_LPC_ADDR_HOST_PARAM 0x804
-#define EC_HOST_PARAM_SIZE 0x0fc /* Size of param area in bytes */
-
-/* I/O addresses for host command params, old interface */
-#define EC_LPC_ADDR_OLD_PARAM 0x880
-#define EC_OLD_PARAM_SIZE 0x080 /* Size of param area in bytes */
+/* Protocol version 2 */
+#define EC_LPC_ADDR_HOST_ARGS 0x800 /* And 0x801, 0x802, 0x803 */
+#define EC_LPC_ADDR_HOST_PARAM 0x804 /* For version 2 params; size is
+ * EC_PROTO2_MAX_PARAM_SIZE */
+/* Protocol version 3 */
+#define EC_LPC_ADDR_HOST_PACKET 0x800 /* Offset of version 3 packet */
+#define EC_LPC_HOST_PACKET_SIZE 0x100 /* Max size of version 3 packet */
+
+/* The actual block is 0x800-0x8ff, but some BIOSes think it's 0x880-0x8ff
+ * and they tell the kernel that so we have to think of it as two parts. */
+#define EC_HOST_CMD_REGION0 0x800
+#define EC_HOST_CMD_REGION1 0x880
+#define EC_HOST_CMD_REGION_SIZE 0x80
/* EC command register bit functions */
#define EC_LPC_CMDR_DATA (1 << 0) /* Data ready for host to read */
@@ -79,18 +72,22 @@
#define EC_MEMMAP_TEXT_MAX 8 /* Size of a string in the memory map */
/* The offset address of each type of data in mapped memory. */
-#define EC_MEMMAP_TEMP_SENSOR 0x00 /* Temp sensors */
-#define EC_MEMMAP_FAN 0x10 /* Fan speeds */
-#define EC_MEMMAP_TEMP_SENSOR_B 0x18 /* Temp sensors (second set) */
-#define EC_MEMMAP_ID 0x20 /* 'E' 'C' */
+#define EC_MEMMAP_TEMP_SENSOR 0x00 /* Temp sensors 0x00 - 0x0f */
+#define EC_MEMMAP_FAN 0x10 /* Fan speeds 0x10 - 0x17 */
+#define EC_MEMMAP_TEMP_SENSOR_B 0x18 /* More temp sensors 0x18 - 0x1f */
+#define EC_MEMMAP_ID 0x20 /* 0x20 == 'E', 0x21 == 'C' */
#define EC_MEMMAP_ID_VERSION 0x22 /* Version of data in 0x20 - 0x2f */
#define EC_MEMMAP_THERMAL_VERSION 0x23 /* Version of data in 0x00 - 0x1f */
#define EC_MEMMAP_BATTERY_VERSION 0x24 /* Version of data in 0x40 - 0x7f */
#define EC_MEMMAP_SWITCHES_VERSION 0x25 /* Version of data in 0x30 - 0x33 */
#define EC_MEMMAP_EVENTS_VERSION 0x26 /* Version of data in 0x34 - 0x3f */
-#define EC_MEMMAP_HOST_CMD_FLAGS 0x27 /* Host command interface flags */
-#define EC_MEMMAP_SWITCHES 0x30
-#define EC_MEMMAP_HOST_EVENTS 0x34
+#define EC_MEMMAP_HOST_CMD_FLAGS 0x27 /* Host cmd interface flags (8 bits) */
+/* Unused 0x28 - 0x2f */
+#define EC_MEMMAP_SWITCHES 0x30 /* 8 bits */
+/* Unused 0x31 - 0x33 */
+#define EC_MEMMAP_HOST_EVENTS 0x34 /* 32 bits */
+/* Reserve 0x38 - 0x3f for additional host event-related stuff */
+/* Battery values are all 32 bits */
#define EC_MEMMAP_BATT_VOLT 0x40 /* Battery Present Voltage */
#define EC_MEMMAP_BATT_RATE 0x44 /* Battery Present Rate */
#define EC_MEMMAP_BATT_CAP 0x48 /* Battery Remaining Capacity */
@@ -99,10 +96,24 @@
#define EC_MEMMAP_BATT_DVLT 0x54 /* Battery Design Voltage */
#define EC_MEMMAP_BATT_LFCC 0x58 /* Battery Last Full Charge Capacity */
#define EC_MEMMAP_BATT_CCNT 0x5c /* Battery Cycle Count */
+/* Strings are all 8 bytes (EC_MEMMAP_TEXT_MAX) */
#define EC_MEMMAP_BATT_MFGR 0x60 /* Battery Manufacturer String */
#define EC_MEMMAP_BATT_MODEL 0x68 /* Battery Model Number String */
#define EC_MEMMAP_BATT_SERIAL 0x70 /* Battery Serial Number String */
#define EC_MEMMAP_BATT_TYPE 0x78 /* Battery Type String */
+#define EC_MEMMAP_ALS 0x80 /* ALS readings in lux (2 X 16 bits) */
+/* Unused 0x84 - 0x8f */
+#define EC_MEMMAP_ACC_STATUS 0x90 /* Accelerometer status (8 bits )*/
+/* Unused 0x91 */
+#define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometer data 0x92 - 0x9f */
+#define EC_MEMMAP_GYRO_DATA 0xa0 /* Gyroscope data 0xa0 - 0xa5 */
+/* Unused 0xa6 - 0xfe (remember, 0xff is NOT part of the memmap region) */
+
+
+/* Define the format of the accelerometer mapped memory status byte. */
+#define EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK 0x0f
+#define EC_MEMMAP_ACC_STATUS_BUSY_BIT (1 << 4)
+#define EC_MEMMAP_ACC_STATUS_PRESENCE_BIT (1 << 7)
/* Number of temp sensors at EC_MEMMAP_TEMP_SENSOR */
#define EC_TEMP_SENSOR_ENTRIES 16
@@ -112,6 +123,8 @@
* Valid only if EC_MEMMAP_THERMAL_VERSION returns >= 2.
*/
#define EC_TEMP_SENSOR_B_ENTRIES 8
+
+/* Special values for mapped temperature sensors */
#define EC_TEMP_SENSOR_NOT_PRESENT 0xff
#define EC_TEMP_SENSOR_ERROR 0xfe
#define EC_TEMP_SENSOR_NOT_POWERED 0xfd
@@ -122,6 +135,18 @@
*/
#define EC_TEMP_SENSOR_OFFSET 200
+/*
+ * Number of ALS readings at EC_MEMMAP_ALS
+ */
+#define EC_ALS_ENTRIES 2
+
+/*
+ * The default value a temperature sensor will return when it is present but
+ * has not been read this boot. This is a reasonable number to avoid
+ * triggering alarms on the host.
+ */
+#define EC_TEMP_SENSOR_DEFAULT (296 - EC_TEMP_SENSOR_OFFSET)
+
#define EC_FAN_SPEED_ENTRIES 4 /* Number of fans at EC_MEMMAP_FAN */
#define EC_FAN_SPEED_NOT_PRESENT 0xffff /* Entry not present */
#define EC_FAN_SPEED_STALLED 0xfffe /* Fan stalled */
@@ -137,8 +162,8 @@
#define EC_SWITCH_LID_OPEN 0x01
#define EC_SWITCH_POWER_BUTTON_PRESSED 0x02
#define EC_SWITCH_WRITE_PROTECT_DISABLED 0x04
-/* Recovery requested via keyboard */
-#define EC_SWITCH_KEYBOARD_RECOVERY 0x08
+/* Was recovery requested via keyboard; now unused. */
+#define EC_SWITCH_IGNORE1 0x08
/* Recovery requested via dedicated signal (from servo board) */
#define EC_SWITCH_DEDICATED_RECOVERY 0x10
/* Was fake developer mode switch; now unused. Remove in next refactor. */
@@ -147,10 +172,15 @@
/* Host command interface flags */
/* Host command interface supports LPC args (LPC interface only) */
#define EC_HOST_CMD_FLAG_LPC_ARGS_SUPPORTED 0x01
+/* Host command interface supports version 3 protocol */
+#define EC_HOST_CMD_FLAG_VERSION_3 0x02
/* Wireless switch flags */
-#define EC_WIRELESS_SWITCH_WLAN 0x01
-#define EC_WIRELESS_SWITCH_BLUETOOTH 0x02
+#define EC_WIRELESS_SWITCH_ALL ~0x00 /* All flags */
+#define EC_WIRELESS_SWITCH_WLAN 0x01 /* WLAN radio */
+#define EC_WIRELESS_SWITCH_BLUETOOTH 0x02 /* Bluetooth radio */
+#define EC_WIRELESS_SWITCH_WWAN 0x04 /* WWAN power */
+#define EC_WIRELESS_SWITCH_WLAN_POWER 0x08 /* WLAN power */
/*
* This header file is used in coreboot both in C and ACPI code. The ACPI code
@@ -159,6 +189,14 @@
*/
#ifndef __ACPI__
+/*
+ * Define __packed if someone hasn't beat us to it. Linux kernel style
+ * checking prefers __packed over __attribute__((packed)).
+ */
+#ifndef __packed
+#define __packed __attribute__((packed))
+#endif
+
/* LPC command status byte masks */
/* EC has written a byte in the data register and host hasn't read it yet */
#define EC_LPC_STATUS_TO_HOST 0x01
@@ -198,6 +236,9 @@ enum ec_status {
EC_RES_UNAVAILABLE = 9, /* No response available */
EC_RES_TIMEOUT = 10, /* We got a timeout */
EC_RES_OVERFLOW = 11, /* Table / data overflow */
+ EC_RES_INVALID_HEADER = 12, /* Header contains invalid data */
+ EC_RES_REQUEST_TRUNCATED = 13, /* Didn't get the entire request */
+ EC_RES_RESPONSE_TOO_BIG = 14 /* Response was too big to handle */
};
/*
@@ -235,6 +276,16 @@ enum host_event_code {
/* Shutdown due to battery level too low */
EC_HOST_EVENT_BATTERY_SHUTDOWN = 17,
+ /* Suggest that the AP throttle itself */
+ EC_HOST_EVENT_THROTTLE_START = 18,
+ /* Suggest that the AP resume normal speed */
+ EC_HOST_EVENT_THROTTLE_STOP = 19,
+
+ /* Hang detect logic detected a hang and host event timeout expired */
+ EC_HOST_EVENT_HANG_DETECT = 20,
+ /* Hang detect logic detected a hang and warm rebooted the AP */
+ EC_HOST_EVENT_HANG_REBOOT = 21,
+
/*
* The high bit of the event mask is not used as a host event code. If
* it reads back as set, then the entire event mask should be
@@ -279,6 +330,188 @@ struct ec_lpc_host_args {
*/
#define EC_HOST_ARGS_FLAG_TO_HOST 0x02
+/*****************************************************************************/
+/*
+ * Byte codes returned by EC over SPI interface.
+ *
+ * These can be used by the AP to debug the EC interface, and to determine
+ * when the EC is not in a state where it will ever get around to responding
+ * to the AP.
+ *
+ * Example of sequence of bytes read from EC for a current good transfer:
+ * 1. - - AP asserts chip select (CS#)
+ * 2. EC_SPI_OLD_READY - AP sends first byte(s) of request
+ * 3. - - EC starts handling CS# interrupt
+ * 4. EC_SPI_RECEIVING - AP sends remaining byte(s) of request
+ * 5. EC_SPI_PROCESSING - EC starts processing request; AP is clocking in
+ * bytes looking for EC_SPI_FRAME_START
+ * 6. - - EC finishes processing and sets up response
+ * 7. EC_SPI_FRAME_START - AP reads frame byte
+ * 8. (response packet) - AP reads response packet
+ * 9. EC_SPI_PAST_END - Any additional bytes read by AP
+ * 10 - - AP deasserts chip select
+ * 11 - - EC processes CS# interrupt and sets up DMA for
+ * next request
+ *
+ * If the AP is waiting for EC_SPI_FRAME_START and sees any value other than
+ * the following byte values:
+ * EC_SPI_OLD_READY
+ * EC_SPI_RX_READY
+ * EC_SPI_RECEIVING
+ * EC_SPI_PROCESSING
+ *
+ * Then the EC found an error in the request, or was not ready for the request
+ * and lost data. The AP should give up waiting for EC_SPI_FRAME_START,
+ * because the EC is unable to tell when the AP is done sending its request.
+ */
+
+/*
+ * Framing byte which precedes a response packet from the EC. After sending a
+ * request, the AP will clock in bytes until it sees the framing byte, then
+ * clock in the response packet.
+ */
+#define EC_SPI_FRAME_START 0xec
+
+/*
+ * Padding bytes which are clocked out after the end of a response packet.
+ */
+#define EC_SPI_PAST_END 0xed
+
+/*
+ * EC is ready to receive, and has ignored the byte sent by the AP. EC expects
+ * that the AP will send a valid packet header (starting with
+ * EC_COMMAND_PROTOCOL_3) in the next 32 bytes.
+ */
+#define EC_SPI_RX_READY 0xf8
+
+/*
+ * EC has started receiving the request from the AP, but hasn't started
+ * processing it yet.
+ */
+#define EC_SPI_RECEIVING 0xf9
+
+/* EC has received the entire request from the AP and is processing it. */
+#define EC_SPI_PROCESSING 0xfa
+
+/*
+ * EC received bad data from the AP, such as a packet header with an invalid
+ * length. EC will ignore all data until chip select deasserts.
+ */
+#define EC_SPI_RX_BAD_DATA 0xfb
+
+/*
+ * EC received data from the AP before it was ready. That is, the AP asserted
+ * chip select and started clocking data before the EC was ready to receive it.
+ * EC will ignore all data until chip select deasserts.
+ */
+#define EC_SPI_NOT_READY 0xfc
+
+/*
+ * EC was ready to receive a request from the AP. EC has treated the byte sent
+ * by the AP as part of a request packet, or (for old-style ECs) is processing
+ * a fully received packet but is not ready to respond yet.
+ */
+#define EC_SPI_OLD_READY 0xfd
+
+/*****************************************************************************/
+
+/*
+ * Protocol version 2 for I2C and SPI send a request this way:
+ *
+ * 0 EC_CMD_VERSION0 + (command version)
+ * 1 Command number
+ * 2 Length of params = N
+ * 3..N+2 Params, if any
+ * N+3 8-bit checksum of bytes 0..N+2
+ *
+ * The corresponding response is:
+ *
+ * 0 Result code (EC_RES_*)
+ * 1 Length of params = M
+ * 2..M+1 Params, if any
+ * M+2 8-bit checksum of bytes 0..M+1
+ */
+#define EC_PROTO2_REQUEST_HEADER_BYTES 3
+#define EC_PROTO2_REQUEST_TRAILER_BYTES 1
+#define EC_PROTO2_REQUEST_OVERHEAD (EC_PROTO2_REQUEST_HEADER_BYTES + \
+ EC_PROTO2_REQUEST_TRAILER_BYTES)
+
+#define EC_PROTO2_RESPONSE_HEADER_BYTES 2
+#define EC_PROTO2_RESPONSE_TRAILER_BYTES 1
+#define EC_PROTO2_RESPONSE_OVERHEAD (EC_PROTO2_RESPONSE_HEADER_BYTES + \
+ EC_PROTO2_RESPONSE_TRAILER_BYTES)
+
+/* Parameter length was limited by the LPC interface */
+#define EC_PROTO2_MAX_PARAM_SIZE 0xfc
+
+/* Maximum request and response packet sizes for protocol version 2 */
+#define EC_PROTO2_MAX_REQUEST_SIZE (EC_PROTO2_REQUEST_OVERHEAD + \
+ EC_PROTO2_MAX_PARAM_SIZE)
+#define EC_PROTO2_MAX_RESPONSE_SIZE (EC_PROTO2_RESPONSE_OVERHEAD + \
+ EC_PROTO2_MAX_PARAM_SIZE)
+
+/*****************************************************************************/
+
+/*
+ * Value written to legacy command port / prefix byte to indicate protocol
+ * 3+ structs are being used. Usage is bus-dependent.
+ */
+#define EC_COMMAND_PROTOCOL_3 0xda
+
+#define EC_HOST_REQUEST_VERSION 3
+
+/* Version 3 request from host */
+struct ec_host_request {
+ /* Struct version (=3)
+ *
+ * EC will return EC_RES_INVALID_HEADER if it receives a header with a
+ * version it doesn't know how to parse.
+ */
+ uint8_t struct_version;
+
+ /*
+ * Checksum of request and data; sum of all bytes including checksum
+ * should total to 0.
+ */
+ uint8_t checksum;
+
+ /* Command code */
+ uint16_t command;
+
+ /* Command version */
+ uint8_t command_version;
+
+ /* Unused byte in current protocol version; set to 0 */
+ uint8_t reserved;
+
+ /* Length of data which follows this header */
+ uint16_t data_len;
+} __packed;
+
+#define EC_HOST_RESPONSE_VERSION 3
+
+/* Version 3 response from EC */
+struct ec_host_response {
+ /* Struct version (=3) */
+ uint8_t struct_version;
+
+ /*
+ * Checksum of response and data; sum of all bytes including checksum
+ * should total to 0.
+ */
+ uint8_t checksum;
+
+ /* Result code (EC_RES_*) */
+ uint16_t result;
+
+ /* Length of data which follows this header */
+ uint16_t data_len;
+
+ /* Unused bytes in current protocol version; set to 0 */
+ uint16_t reserved;
+} __packed;
+
+/*****************************************************************************/
/*
* Notes on commands:
*
@@ -418,6 +651,68 @@ struct ec_response_get_comms_status {
uint32_t flags; /* Mask of enum ec_comms_status */
} __packed;
+/* Fake a variety of responses, purely for testing purposes. */
+#define EC_CMD_TEST_PROTOCOL 0x0a
+
+/* Tell the EC what to send back to us. */
+struct ec_params_test_protocol {
+ uint32_t ec_result;
+ uint32_t ret_len;
+ uint8_t buf[32];
+} __packed;
+
+/* Here it comes... */
+struct ec_response_test_protocol {
+ uint8_t buf[32];
+} __packed;
+
+/* Get prococol information */
+#define EC_CMD_GET_PROTOCOL_INFO 0x0b
+
+/* Flags for ec_response_get_protocol_info.flags */
+/* EC_RES_IN_PROGRESS may be returned if a command is slow */
+#define EC_PROTOCOL_INFO_IN_PROGRESS_SUPPORTED (1 << 0)
+
+struct ec_response_get_protocol_info {
+ /* Fields which exist if at least protocol version 3 supported */
+
+ /* Bitmask of protocol versions supported (1 << n means version n)*/
+ uint32_t protocol_versions;
+
+ /* Maximum request packet size, in bytes */
+ uint16_t max_request_packet_size;
+
+ /* Maximum response packet size, in bytes */
+ uint16_t max_response_packet_size;
+
+ /* Flags; see EC_PROTOCOL_INFO_* */
+ uint32_t flags;
+} __packed;
+
+
+/*****************************************************************************/
+/* Get/Set miscellaneous values */
+
+/* The upper byte of .flags tells what to do (nothing means "get") */
+#define EC_GSV_SET 0x80000000
+
+/* The lower three bytes of .flags identifies the parameter, if that has
+ meaning for an individual command. */
+#define EC_GSV_PARAM_MASK 0x00ffffff
+
+struct ec_params_get_set_value {
+ uint32_t flags;
+ uint32_t value;
+} __packed;
+
+struct ec_response_get_set_value {
+ uint32_t flags;
+ uint32_t value;
+} __packed;
+
+/* More than one command can use these structs to get/set paramters. */
+#define EC_CMD_GSV_PAUSE_IN_S5 0x0c
+
/*****************************************************************************/
/* Flash commands */
@@ -425,6 +720,7 @@ struct ec_response_get_comms_status {
/* Get flash info */
#define EC_CMD_FLASH_INFO 0x10
+/* Version 0 returns these fields */
struct ec_response_flash_info {
/* Usable flash size, in bytes */
uint32_t flash_size;
@@ -445,6 +741,37 @@ struct ec_response_flash_info {
uint32_t protect_block_size;
} __packed;
+/* Flags for version 1+ flash info command */
+/* EC flash erases bits to 0 instead of 1 */
+#define EC_FLASH_INFO_ERASE_TO_0 (1 << 0)
+
+/*
+ * Version 1 returns the same initial fields as version 0, with additional
+ * fields following.
+ *
+ * gcc anonymous structs don't seem to get along with the __packed directive;
+ * if they did we'd define the version 0 struct as a sub-struct of this one.
+ */
+struct ec_response_flash_info_1 {
+ /* Version 0 fields; see above for description */
+ uint32_t flash_size;
+ uint32_t write_block_size;
+ uint32_t erase_block_size;
+ uint32_t protect_block_size;
+
+ /* Version 1 adds these fields: */
+ /*
+ * Ideal write size in bytes. Writes will be fastest if size is
+ * exactly this and offset is a multiple of this. For example, an EC
+ * may have a write buffer which can do half-page operations if data is
+ * aligned, and a slower word-at-a-time write mode.
+ */
+ uint32_t write_ideal_size;
+
+ /* Flags; see EC_FLASH_INFO_* */
+ uint32_t flags;
+} __packed;
+
/*
* Read flash
*
@@ -459,15 +786,15 @@ struct ec_params_flash_read {
/* Write flash */
#define EC_CMD_FLASH_WRITE 0x12
+#define EC_VER_FLASH_WRITE 1
+
+/* Version 0 of the flash command supported only 64 bytes of data */
+#define EC_FLASH_WRITE_VER0_SIZE 64
struct ec_params_flash_write {
uint32_t offset; /* Byte offset to write */
uint32_t size; /* Size to write in bytes */
- /*
- * Data to write. Could really use EC_PARAM_SIZE - 8, but tidiest to
- * use a power of 2 so writes stay aligned.
- */
- uint8_t data[64];
+ /* Followed by data to write */
} __packed;
/* Erase flash */
@@ -543,7 +870,7 @@ struct ec_response_flash_protect {
enum ec_flash_region {
/* Region which holds read-only EC image */
- EC_FLASH_REGION_RO,
+ EC_FLASH_REGION_RO = 0,
/* Region which holds rewritable EC image */
EC_FLASH_REGION_RW,
/*
@@ -551,6 +878,8 @@ enum ec_flash_region {
* EC_FLASH_REGION_RO)
*/
EC_FLASH_REGION_WP_RO,
+ /* Number of regions */
+ EC_FLASH_REGION_COUNT,
};
struct ec_params_flash_region_info {
@@ -639,15 +968,15 @@ struct rgb_s {
*/
struct lightbar_params {
/* Timing */
- int google_ramp_up;
- int google_ramp_down;
- int s3s0_ramp_up;
- int s0_tick_delay[2]; /* AC=0/1 */
- int s0a_tick_delay[2]; /* AC=0/1 */
- int s0s3_ramp_down;
- int s3_sleep_for;
- int s3_ramp_up;
- int s3_ramp_down;
+ int32_t google_ramp_up;
+ int32_t google_ramp_down;
+ int32_t s3s0_ramp_up;
+ int32_t s0_tick_delay[2]; /* AC=0/1 */
+ int32_t s0a_tick_delay[2]; /* AC=0/1 */
+ int32_t s0s3_ramp_down;
+ int32_t s3_sleep_for;
+ int32_t s3_ramp_up;
+ int32_t s3_ramp_down;
/* Oscillation */
uint8_t new_s0;
@@ -676,7 +1005,7 @@ struct ec_params_lightbar {
union {
struct {
/* no args */
- } dump, off, on, init, get_seq, get_params;
+ } dump, off, on, init, get_seq, get_params, version;
struct num {
uint8_t num;
@@ -710,6 +1039,11 @@ struct ec_response_lightbar {
struct lightbar_params get_params;
+ struct version {
+ uint32_t num;
+ uint32_t flags;
+ } version;
+
struct {
/* no return params */
} off, on, init, brightness, seq, reg, rgb, demo, set_params;
@@ -730,10 +1064,62 @@ enum lightbar_command {
LIGHTBAR_CMD_DEMO = 9,
LIGHTBAR_CMD_GET_PARAMS = 10,
LIGHTBAR_CMD_SET_PARAMS = 11,
+ LIGHTBAR_CMD_VERSION = 12,
LIGHTBAR_NUM_CMDS
};
/*****************************************************************************/
+/* LED control commands */
+
+#define EC_CMD_LED_CONTROL 0x29
+
+enum ec_led_id {
+ /* LED to indicate battery state of charge */
+ EC_LED_ID_BATTERY_LED = 0,
+ /*
+ * LED to indicate system power state (on or in suspend).
+ * May be on power button or on C-panel.
+ */
+ EC_LED_ID_POWER_LED,
+ /* LED on power adapter or its plug */
+ EC_LED_ID_ADAPTER_LED,
+
+ EC_LED_ID_COUNT
+};
+
+/* LED control flags */
+#define EC_LED_FLAGS_QUERY (1 << 0) /* Query LED capability only */
+#define EC_LED_FLAGS_AUTO (1 << 1) /* Switch LED back to automatic control */
+
+enum ec_led_colors {
+ EC_LED_COLOR_RED = 0,
+ EC_LED_COLOR_GREEN,
+ EC_LED_COLOR_BLUE,
+ EC_LED_COLOR_YELLOW,
+ EC_LED_COLOR_WHITE,
+
+ EC_LED_COLOR_COUNT
+};
+
+struct ec_params_led_control {
+ uint8_t led_id; /* Which LED to control */
+ uint8_t flags; /* Control flags */
+
+ uint8_t brightness[EC_LED_COLOR_COUNT];
+} __packed;
+
+struct ec_response_led_control {
+ /*
+ * Available brightness value range.
+ *
+ * Range 0 means color channel not present.
+ * Range 1 means on/off control.
+ * Other values means the LED is control by PWM.
+ */
+ uint8_t brightness_range[EC_LED_COLOR_COUNT];
+} __packed;
+
+/*****************************************************************************/
/* Verified boot commands */
/*
@@ -790,6 +1176,181 @@ enum ec_vboot_hash_status {
#define EC_VBOOT_HASH_OFFSET_RW 0xfffffffd
/*****************************************************************************/
+/*
+ * Motion sense commands. We'll make separate structs for sub-commands with
+ * different input args, so that we know how much to expect.
+ */
+#define EC_CMD_MOTION_SENSE_CMD 0x2B
+
+/* Motion sense commands */
+enum motionsense_command {
+ /*
+ * Dump command returns all motion sensor data including motion sense
+ * module flags and individual sensor flags.
+ */
+ MOTIONSENSE_CMD_DUMP = 0,
+
+ /*
+ * Info command returns data describing the details of a given sensor,
+ * including enum motionsensor_type, enum motionsensor_location, and
+ * enum motionsensor_chip.
+ */
+ MOTIONSENSE_CMD_INFO = 1,
+
+ /*
+ * EC Rate command is a setter/getter command for the EC sampling rate
+ * of all motion sensors in milliseconds.
+ */
+ MOTIONSENSE_CMD_EC_RATE = 2,
+
+ /*
+ * Sensor ODR command is a setter/getter command for the output data
+ * rate of a specific motion sensor in millihertz.
+ */
+ MOTIONSENSE_CMD_SENSOR_ODR = 3,
+
+ /*
+ * Sensor range command is a setter/getter command for the range of
+ * a specified motion sensor in +/-G's or +/- deg/s.
+ */
+ MOTIONSENSE_CMD_SENSOR_RANGE = 4,
+
+ /*
+ * Setter/getter command for the keyboard wake angle. When the lid
+ * angle is greater than this value, keyboard wake is disabled in S3,
+ * and when the lid angle goes less than this value, keyboard wake is
+ * enabled. Note, the lid angle measurement is an approximate,
+ * un-calibrated value, hence the wake angle isn't exact.
+ */
+ MOTIONSENSE_CMD_KB_WAKE_ANGLE = 5,
+
+ /* Number of motionsense sub-commands. */
+ MOTIONSENSE_NUM_CMDS
+};
+
+enum motionsensor_id {
+ EC_MOTION_SENSOR_ACCEL_BASE = 0,
+ EC_MOTION_SENSOR_ACCEL_LID = 1,
+ EC_MOTION_SENSOR_GYRO = 2,
+
+ /*
+ * Note, if more sensors are added and this count changes, the padding
+ * in ec_response_motion_sense dump command must be modified.
+ */
+ EC_MOTION_SENSOR_COUNT = 3
+};
+
+/* List of motion sensor types. */
+enum motionsensor_type {
+ MOTIONSENSE_TYPE_ACCEL = 0,
+ MOTIONSENSE_TYPE_GYRO = 1,
+};
+
+/* List of motion sensor locations. */
+enum motionsensor_location {
+ MOTIONSENSE_LOC_BASE = 0,
+ MOTIONSENSE_LOC_LID = 1,
+};
+
+/* List of motion sensor chips. */
+enum motionsensor_chip {
+ MOTIONSENSE_CHIP_KXCJ9 = 0,
+};
+
+/* Module flag masks used for the dump sub-command. */
+#define MOTIONSENSE_MODULE_FLAG_ACTIVE (1<<0)
+
+/* Sensor flag masks used for the dump sub-command. */
+#define MOTIONSENSE_SENSOR_FLAG_PRESENT (1<<0)
+
+/*
+ * Send this value for the data element to only perform a read. If you
+ * send any other value, the EC will interpret it as data to set and will
+ * return the actual value set.
+ */
+#define EC_MOTION_SENSE_NO_VALUE -1
+
+struct ec_params_motion_sense {
+ uint8_t cmd;
+ union {
+ /* Used for MOTIONSENSE_CMD_DUMP. */
+ struct {
+ /* no args */
+ } dump;
+
+ /*
+ * Used for MOTIONSENSE_CMD_EC_RATE and
+ * MOTIONSENSE_CMD_KB_WAKE_ANGLE.
+ */
+ struct {
+ /* Data to set or EC_MOTION_SENSE_NO_VALUE to read. */
+ int16_t data;
+ } ec_rate, kb_wake_angle;
+
+ /* Used for MOTIONSENSE_CMD_INFO. */
+ struct {
+ /* Should be element of enum motionsensor_id. */
+ uint8_t sensor_num;
+ } info;
+
+ /*
+ * Used for MOTIONSENSE_CMD_SENSOR_ODR and
+ * MOTIONSENSE_CMD_SENSOR_RANGE.
+ */
+ struct {
+ /* Should be element of enum motionsensor_id. */
+ uint8_t sensor_num;
+
+ /* Rounding flag, true for round-up, false for down. */
+ uint8_t roundup;
+
+ uint16_t reserved;
+
+ /* Data to set or EC_MOTION_SENSE_NO_VALUE to read. */
+ int32_t data;
+ } sensor_odr, sensor_range;
+ };
+} __packed;
+
+struct ec_response_motion_sense {
+ union {
+ /* Used for MOTIONSENSE_CMD_DUMP. */
+ struct {
+ /* Flags representing the motion sensor module. */
+ uint8_t module_flags;
+
+ /* Flags for each sensor in enum motionsensor_id. */
+ uint8_t sensor_flags[EC_MOTION_SENSOR_COUNT];
+
+ /* Array of all sensor data. Each sensor is 3-axis. */
+ int16_t data[3*EC_MOTION_SENSOR_COUNT];
+ } dump;
+
+ /* Used for MOTIONSENSE_CMD_INFO. */
+ struct {
+ /* Should be element of enum motionsensor_type. */
+ uint8_t type;
+
+ /* Should be element of enum motionsensor_location. */
+ uint8_t location;
+
+ /* Should be element of enum motionsensor_chip. */
+ uint8_t chip;
+ } info;
+
+ /*
+ * Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR,
+ * MOTIONSENSE_CMD_SENSOR_RANGE, and
+ * MOTIONSENSE_CMD_KB_WAKE_ANGLE.
+ */
+ struct {
+ /* Current value of the parameter queried. */
+ int32_t ret;
+ } ec_rate, sensor_odr, sensor_range, kb_wake_angle;
+ };
+} __packed;
+
+/*****************************************************************************/
/* USB charging control commands */
/* Set USB port charging mode */
@@ -868,20 +1429,27 @@ struct ec_response_port80_last_boot {
} __packed;
/*****************************************************************************/
-/* Thermal engine commands */
+/* Thermal engine commands. Note that there are two implementations. We'll
+ * reuse the command number, but the data and behavior is incompatible.
+ * Version 0 is what originally shipped on Link.
+ * Version 1 separates the CPU thermal limits from the fan control.
+ */
-/* Set thershold value */
#define EC_CMD_THERMAL_SET_THRESHOLD 0x50
+#define EC_CMD_THERMAL_GET_THRESHOLD 0x51
+
+/* The version 0 structs are opaque. You have to know what they are for
+ * the get/set commands to make any sense.
+ */
+/* Version 0 - set */
struct ec_params_thermal_set_threshold {
uint8_t sensor_type;
uint8_t threshold_id;
uint16_t value;
} __packed;
-/* Get threshold value */
-#define EC_CMD_THERMAL_GET_THRESHOLD 0x51
-
+/* Version 0 - get */
struct ec_params_thermal_get_threshold {
uint8_t sensor_type;
uint8_t threshold_id;
@@ -891,6 +1459,41 @@ struct ec_response_thermal_get_threshold {
uint16_t value;
} __packed;
+
+/* The version 1 structs are visible. */
+enum ec_temp_thresholds {
+ EC_TEMP_THRESH_WARN = 0,
+ EC_TEMP_THRESH_HIGH,
+ EC_TEMP_THRESH_HALT,
+
+ EC_TEMP_THRESH_COUNT
+};
+
+/* Thermal configuration for one temperature sensor. Temps are in degrees K.
+ * Zero values will be silently ignored by the thermal task.
+ */
+struct ec_thermal_config {
+ uint32_t temp_host[EC_TEMP_THRESH_COUNT]; /* levels of hotness */
+ uint32_t temp_fan_off; /* no active cooling needed */
+ uint32_t temp_fan_max; /* max active cooling needed */
+} __packed;
+
+/* Version 1 - get config for one sensor. */
+struct ec_params_thermal_get_threshold_v1 {
+ uint32_t sensor_num;
+} __packed;
+/* This returns a struct ec_thermal_config */
+
+/* Version 1 - set config for one sensor.
+ * Use read-modify-write for best results! */
+struct ec_params_thermal_set_threshold_v1 {
+ uint32_t sensor_num;
+ struct ec_thermal_config cfg;
+} __packed;
+/* This returns no data */
+
+/****************************************************************************/
+
/* Toggle automatic fan control */
#define EC_CMD_THERMAL_AUTO_FAN_CTRL 0x52
@@ -920,6 +1523,18 @@ struct ec_params_tmp006_set_calibration {
float b2;
} __packed;
+/* Read raw TMP006 data */
+#define EC_CMD_TMP006_GET_RAW 0x55
+
+struct ec_params_tmp006_get_raw {
+ uint8_t index;
+} __packed;
+
+struct ec_response_tmp006_get_raw {
+ int32_t t; /* In 1/100 K */
+ int32_t v; /* In nV */
+};
+
/*****************************************************************************/
/* MKBP - Matrix KeyBoard Protocol */
@@ -1118,11 +1733,41 @@ struct ec_params_switch_enable_backlight {
/* Enable/disable WLAN/Bluetooth */
#define EC_CMD_SWITCH_ENABLE_WIRELESS 0x91
+#define EC_VER_SWITCH_ENABLE_WIRELESS 1
-struct ec_params_switch_enable_wireless {
+/* Version 0 params; no response */
+struct ec_params_switch_enable_wireless_v0 {
uint8_t enabled;
} __packed;
+/* Version 1 params */
+struct ec_params_switch_enable_wireless_v1 {
+ /* Flags to enable now */
+ uint8_t now_flags;
+
+ /* Which flags to copy from now_flags */
+ uint8_t now_mask;
+
+ /*
+ * Flags to leave enabled in S3, if they're on at the S0->S3
+ * transition. (Other flags will be disabled by the S0->S3
+ * transition.)
+ */
+ uint8_t suspend_flags;
+
+ /* Which flags to copy from suspend_flags */
+ uint8_t suspend_mask;
+} __packed;
+
+/* Version 1 response */
+struct ec_response_switch_enable_wireless_v1 {
+ /* Flags to enable now */
+ uint8_t now_flags;
+
+ /* Flags to leave enabled in S3 */
+ uint8_t suspend_flags;
+} __packed;
+
/*****************************************************************************/
/* GPIO commands. Only available on EC if write protect has been disabled. */
@@ -1147,11 +1792,16 @@ struct ec_response_gpio_get {
/*****************************************************************************/
/* I2C commands. Only available when flash write protect is unlocked. */
+/*
+ * TODO(crosbug.com/p/23570): These commands are deprecated, and will be
+ * removed soon. Use EC_CMD_I2C_XFER instead.
+ */
+
/* Read I2C bus */
#define EC_CMD_I2C_READ 0x94
struct ec_params_i2c_read {
- uint16_t addr;
+ uint16_t addr; /* 8-bit address (7-bit shifted << 1) */
uint8_t read_size; /* Either 8 or 16. */
uint8_t port;
uint8_t offset;
@@ -1165,7 +1815,7 @@ struct ec_response_i2c_read {
struct ec_params_i2c_write {
uint16_t data;
- uint16_t addr;
+ uint16_t addr; /* 8-bit address (7-bit shifted << 1) */
uint8_t write_size; /* Either 8 or 16. */
uint8_t port;
uint8_t offset;
@@ -1174,11 +1824,20 @@ struct ec_params_i2c_write {
/*****************************************************************************/
/* Charge state commands. Only available when flash write protect unlocked. */
-/* Force charge state machine to stop in idle mode */
-#define EC_CMD_CHARGE_FORCE_IDLE 0x96
+/* Force charge state machine to stop charging the battery or force it to
+ * discharge the battery.
+ */
+#define EC_CMD_CHARGE_CONTROL 0x96
+#define EC_VER_CHARGE_CONTROL 1
-struct ec_params_force_idle {
- uint8_t enabled;
+enum ec_charge_control_mode {
+ CHARGE_CONTROL_NORMAL = 0,
+ CHARGE_CONTROL_IDLE,
+ CHARGE_CONTROL_DISCHARGE,
+};
+
+struct ec_params_charge_control {
+ uint32_t mode; /* enum charge_control_mode */
} __packed;
/*****************************************************************************/
@@ -1206,14 +1865,231 @@ struct ec_params_force_idle {
#define EC_CMD_BATTERY_CUT_OFF 0x99
/*****************************************************************************/
-/* Temporary debug commands. TODO: remove this crosbug.com/p/13849 */
+/* USB port mux control. */
/*
- * Dump charge state machine context.
- *
- * Response is a binary dump of charge state machine context.
+ * Switch USB mux or return to automatic switching.
+ */
+#define EC_CMD_USB_MUX 0x9a
+
+struct ec_params_usb_mux {
+ uint8_t mux;
+} __packed;
+
+/*****************************************************************************/
+/* LDOs / FETs control. */
+
+enum ec_ldo_state {
+ EC_LDO_STATE_OFF = 0, /* the LDO / FET is shut down */
+ EC_LDO_STATE_ON = 1, /* the LDO / FET is ON / providing power */
+};
+
+/*
+ * Switch on/off a LDO.
+ */
+#define EC_CMD_LDO_SET 0x9b
+
+struct ec_params_ldo_set {
+ uint8_t index;
+ uint8_t state;
+} __packed;
+
+/*
+ * Get LDO state.
+ */
+#define EC_CMD_LDO_GET 0x9c
+
+struct ec_params_ldo_get {
+ uint8_t index;
+} __packed;
+
+struct ec_response_ldo_get {
+ uint8_t state;
+} __packed;
+
+/*****************************************************************************/
+/* Power info. */
+
+/*
+ * Get power info.
+ */
+#define EC_CMD_POWER_INFO 0x9d
+
+struct ec_response_power_info {
+ uint32_t usb_dev_type;
+ uint16_t voltage_ac;
+ uint16_t voltage_system;
+ uint16_t current_system;
+ uint16_t usb_current_limit;
+} __packed;
+
+/*****************************************************************************/
+/* I2C passthru command */
+
+#define EC_CMD_I2C_PASSTHRU 0x9e
+
+/* Slave address is 10 (not 7) bit */
+#define EC_I2C_FLAG_10BIT (1 << 16)
+
+/* Read data; if not present, message is a write */
+#define EC_I2C_FLAG_READ (1 << 15)
+
+/* Mask for address */
+#define EC_I2C_ADDR_MASK 0x3ff
+
+#define EC_I2C_STATUS_NAK (1 << 0) /* Transfer was not acknowledged */
+#define EC_I2C_STATUS_TIMEOUT (1 << 1) /* Timeout during transfer */
+
+/* Any error */
+#define EC_I2C_STATUS_ERROR (EC_I2C_STATUS_NAK | EC_I2C_STATUS_TIMEOUT)
+
+struct ec_params_i2c_passthru_msg {
+ uint16_t addr_flags; /* I2C slave address (7 or 10 bits) and flags */
+ uint16_t len; /* Number of bytes to read or write */
+} __packed;
+
+struct ec_params_i2c_passthru {
+ uint8_t port; /* I2C port number */
+ uint8_t num_msgs; /* Number of messages */
+ struct ec_params_i2c_passthru_msg msg[];
+ /* Data to write for all messages is concatenated here */
+} __packed;
+
+struct ec_response_i2c_passthru {
+ uint8_t i2c_status; /* Status flags (EC_I2C_STATUS_...) */
+ uint8_t num_msgs; /* Number of messages processed */
+ uint8_t data[]; /* Data read by messages concatenated here */
+} __packed;
+
+/*****************************************************************************/
+/* Power button hang detect */
+
+#define EC_CMD_HANG_DETECT 0x9f
+
+/* Reasons to start hang detection timer */
+/* Power button pressed */
+#define EC_HANG_START_ON_POWER_PRESS (1 << 0)
+
+/* Lid closed */
+#define EC_HANG_START_ON_LID_CLOSE (1 << 1)
+
+ /* Lid opened */
+#define EC_HANG_START_ON_LID_OPEN (1 << 2)
+
+/* Start of AP S3->S0 transition (booting or resuming from suspend) */
+#define EC_HANG_START_ON_RESUME (1 << 3)
+
+/* Reasons to cancel hang detection */
+
+/* Power button released */
+#define EC_HANG_STOP_ON_POWER_RELEASE (1 << 8)
+
+/* Any host command from AP received */
+#define EC_HANG_STOP_ON_HOST_COMMAND (1 << 9)
+
+/* Stop on end of AP S0->S3 transition (suspending or shutting down) */
+#define EC_HANG_STOP_ON_SUSPEND (1 << 10)
+
+/*
+ * If this flag is set, all the other fields are ignored, and the hang detect
+ * timer is started. This provides the AP a way to start the hang timer
+ * without reconfiguring any of the other hang detect settings. Note that
+ * you must previously have configured the timeouts.
+ */
+#define EC_HANG_START_NOW (1 << 30)
+
+/*
+ * If this flag is set, all the other fields are ignored (including
+ * EC_HANG_START_NOW). This provides the AP a way to stop the hang timer
+ * without reconfiguring any of the other hang detect settings.
*/
-#define EC_CMD_CHARGE_DUMP 0xa0
+#define EC_HANG_STOP_NOW (1 << 31)
+
+struct ec_params_hang_detect {
+ /* Flags; see EC_HANG_* */
+ uint32_t flags;
+
+ /* Timeout in msec before generating host event, if enabled */
+ uint16_t host_event_timeout_msec;
+
+ /* Timeout in msec before generating warm reboot, if enabled */
+ uint16_t warm_reboot_timeout_msec;
+} __packed;
+
+/*****************************************************************************/
+/* Commands for battery charging */
+
+/*
+ * This is the single catch-all host command to exchange data regarding the
+ * charge state machine (v2 and up).
+ */
+#define EC_CMD_CHARGE_STATE 0xa0
+
+/* Subcommands for this host command */
+enum charge_state_command {
+ CHARGE_STATE_CMD_GET_STATE,
+ CHARGE_STATE_CMD_GET_PARAM,
+ CHARGE_STATE_CMD_SET_PARAM,
+ CHARGE_STATE_NUM_CMDS
+};
+
+/*
+ * Known param numbers are defined here. Ranges are reserved for board-specific
+ * params, which are handled by the particular implementations.
+ */
+enum charge_state_params {
+ CS_PARAM_CHG_VOLTAGE, /* charger voltage limit */
+ CS_PARAM_CHG_CURRENT, /* charger current limit */
+ CS_PARAM_CHG_INPUT_CURRENT, /* charger input current limit */
+ CS_PARAM_CHG_STATUS, /* charger-specific status */
+ CS_PARAM_CHG_OPTION, /* charger-specific options */
+ /* How many so far? */
+ CS_NUM_BASE_PARAMS,
+
+ /* Range for CONFIG_CHARGER_PROFILE_OVERRIDE params */
+ CS_PARAM_CUSTOM_PROFILE_MIN = 0x10000,
+ CS_PARAM_CUSTOM_PROFILE_MAX = 0x1ffff,
+
+ /* Other custom param ranges go here... */
+};
+
+struct ec_params_charge_state {
+ uint8_t cmd; /* enum charge_state_command */
+ union {
+ struct {
+ /* no args */
+ } get_state;
+
+ struct {
+ uint32_t param; /* enum charge_state_param */
+ } get_param;
+
+ struct {
+ uint32_t param; /* param to set */
+ uint32_t value; /* value to set */
+ } set_param;
+ };
+} __packed;
+
+struct ec_response_charge_state {
+ union {
+ struct {
+ int ac;
+ int chg_voltage;
+ int chg_current;
+ int chg_input_current;
+ int batt_state_of_charge;
+ } get_state;
+
+ struct {
+ uint32_t value;
+ } get_param;
+ struct {
+ /* no return values */
+ } set_param;
+ };
+} __packed;
+
/*
* Set maximum battery charging current.
@@ -1221,15 +2097,59 @@ struct ec_params_force_idle {
#define EC_CMD_CHARGE_CURRENT_LIMIT 0xa1
struct ec_params_current_limit {
- uint32_t limit;
+ uint32_t limit; /* in mA */
+} __packed;
+
+/*
+ * Set maximum external power current.
+ */
+#define EC_CMD_EXT_POWER_CURRENT_LIMIT 0xa2
+
+struct ec_params_ext_power_current_limit {
+ uint32_t limit; /* in mA */
+} __packed;
+
+/*****************************************************************************/
+/* Smart battery pass-through */
+
+/* Get / Set 16-bit smart battery registers */
+#define EC_CMD_SB_READ_WORD 0xb0
+#define EC_CMD_SB_WRITE_WORD 0xb1
+
+/* Get / Set string smart battery parameters
+ * formatted as SMBUS "block".
+ */
+#define EC_CMD_SB_READ_BLOCK 0xb2
+#define EC_CMD_SB_WRITE_BLOCK 0xb3
+
+struct ec_params_sb_rd {
+ uint8_t reg;
+} __packed;
+
+struct ec_response_sb_rd_word {
+ uint16_t value;
+} __packed;
+
+struct ec_params_sb_wr_word {
+ uint8_t reg;
+ uint16_t value;
+} __packed;
+
+struct ec_response_sb_rd_block {
+ uint8_t data[32];
+} __packed;
+
+struct ec_params_sb_wr_block {
+ uint8_t reg;
+ uint16_t data[32];
} __packed;
/*****************************************************************************/
/* System commands */
/*
- * TODO: this is a confusing name, since it doesn't necessarily reboot the EC.
- * Rename to "set image" or something similar.
+ * TODO(crosbug.com/p/23747): This is a confusing name, since it doesn't
+ * necessarily reboot the EC. Rename to "image" or something similar?
*/
#define EC_CMD_REBOOT_EC 0xd2
@@ -1308,6 +2228,7 @@ struct ec_params_reboot_ec {
#define EC_CMD_ACPI_QUERY_EVENT 0x84
/* Valid addresses in ACPI memory space, for read/write commands */
+
/* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */
#define EC_ACPI_MEM_VERSION 0x00
/*
@@ -1317,8 +2238,60 @@ struct ec_params_reboot_ec {
#define EC_ACPI_MEM_TEST 0x01
/* Test compliment; writes here are ignored. */
#define EC_ACPI_MEM_TEST_COMPLIMENT 0x02
+
/* Keyboard backlight brightness percent (0 - 100) */
#define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03
+/* DPTF Target Fan Duty (0-100, 0xff for auto/none) */
+#define EC_ACPI_MEM_FAN_DUTY 0x04
+
+/*
+ * DPTF temp thresholds. Any of the EC's temp sensors can have up to two
+ * independent thresholds attached to them. The current value of the ID
+ * register determines which sensor is affected by the THRESHOLD and COMMIT
+ * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme
+ * as the memory-mapped sensors. The COMMIT register applies those settings.
+ *
+ * The spec does not mandate any way to read back the threshold settings
+ * themselves, but when a threshold is crossed the AP needs a way to determine
+ * which sensor(s) are responsible. Each reading of the ID register clears and
+ * returns one sensor ID that has crossed one of its threshold (in either
+ * direction) since the last read. A value of 0xFF means "no new thresholds
+ * have tripped". Setting or enabling the thresholds for a sensor will clear
+ * the unread event count for that sensor.
+ */
+#define EC_ACPI_MEM_TEMP_ID 0x05
+#define EC_ACPI_MEM_TEMP_THRESHOLD 0x06
+#define EC_ACPI_MEM_TEMP_COMMIT 0x07
+/*
+ * Here are the bits for the COMMIT register:
+ * bit 0 selects the threshold index for the chosen sensor (0/1)
+ * bit 1 enables/disables the selected threshold (0 = off, 1 = on)
+ * Each write to the commit register affects one threshold.
+ */
+#define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK (1 << 0)
+#define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK (1 << 1)
+/*
+ * Example:
+ *
+ * Set the thresholds for sensor 2 to 50 C and 60 C:
+ * write 2 to [0x05] -- select temp sensor 2
+ * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET
+ * write 0x2 to [0x07] -- enable threshold 0 with this value
+ * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET
+ * write 0x3 to [0x07] -- enable threshold 1 with this value
+ *
+ * Disable the 60 C threshold, leaving the 50 C threshold unchanged:
+ * write 2 to [0x05] -- select temp sensor 2
+ * write 0x1 to [0x07] -- disable threshold 1
+ */
+
+/* DPTF battery charging current limit */
+#define EC_ACPI_MEM_CHARGING_LIMIT 0x08
+
+/* Charging limit is specified in 64 mA steps */
+#define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64
+/* Value to disable DPTF battery charging limit */
+#define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff
/* Current version of ACPI memory address space */
#define EC_ACPI_MEM_VERSION_CURRENT 1
@@ -1360,10 +2333,21 @@ struct ec_params_reboot_ec {
* Header bytes greater than this indicate a later version. For example,
* EC_CMD_VERSION0 + 1 means we are using version 1.
*
- * The old EC interface must not use commands 0dc or higher.
+ * The old EC interface must not use commands 0xdc or higher.
*/
#define EC_CMD_VERSION0 0xdc
#endif /* !__ACPI__ */
+/*****************************************************************************/
+/*
+ * Deprecated constants. These constants have been renamed for clarity. The
+ * meaning and size has not changed. Programs that use the old names should
+ * switch to the new names soon, as the old names may not be carried forward
+ * forever.
+ */
+#define EC_HOST_PARAM_SIZE EC_PROTO2_MAX_PARAM_SIZE
+#define EC_LPC_ADDR_OLD_PARAM EC_HOST_CMD_REGION1
+#define EC_OLD_PARAM_SIZE EC_HOST_CMD_REGION_SIZE
+
#endif /* __CROS_EC_COMMANDS_H */