| Message ID | 20180831163817.23970-1-marcel@ziswiler.com |
|---|---|
| Headers | show |
| Series | ARM: dts: tegra: apalis_t30: major revamp incl. v1.1 hardware support | expand |
On Fri, Aug 31, 2018 at 06:37:42PM +0200, Marcel Ziswiler wrote: > This series is a major overhaul and adds support for the V1.1 hardware > revision of the Toradex Apalis T30 system on module. > > Changes in v2: > - Clean-up PCIe controller/port status' as well. > - Also move serial UART "nvidia,tegra30-hsuart" compatible to module > level device trees. > - Also add two missing newlines. > - Also replace underscores in node names with dashes. > - Explicitly disable input of BKL1_ON as well. > - Replace underscores in node names with dashes. > - When running some more tests I realized that the reg-addr should > really be 0x3f. Fix this. > - Get rid of fake clocks simple bus as suggested by Rob. > - Replace "[PATCH 27/28] ARM: tegra: apalis_t30: fix pcie switch vendor > compatible" with "[PATCH v2 26/34] dt-bindings: add broadcom (formerly > plx technology) vendor prefix" as suggested by Stefan. > - New patch as suggested by Rob. > - New patch. > - Drop "[PATCH 01/28] ARM: tegra: apalis_t30: enable broken-hpi on emmc" > which should already be handled by the broken-hpi quirk as pointed out > by Dmitry. If I would find more eMMC parts which exhibit the issue I > will add them to the quirk as a separate patch. > - Updated V1.1 device trees with all applicable previous fixes. > > Marcel Ziswiler (34): > ARM: tegra: apalis_t30: fix mmc1 cmd pull-up > ARM: tegra: apalis_t30: pull-up sd card detect pins > ARM: tegra: apalis_t30: add local-mac-address property > ARM: tegra: apalis_t30: reorder pcie properties > ARM: tegra: apalis_t30: annotate/clean-up pcie controller/port nodes > ARM: tegra: apalis_t30: reorder host1x/hdmi properties > ARM: tegra: apalis_t30: regulator clean-up > ARM: tegra: apalis_t30: add missing regulators > ARM: tegra: apalis_t30: annotate uarts and move compatible to board > ARM: tegra: apalis_t30: drop unused cami2c label > ARM: tegra: apalis_t30: white-space/newline clean-up > ARM: tegra: apalis_t30: drop unused mmc1/sd1 labels > ARM: tegra: apalis_t30: annotate mmc1/sd1 > ARM: tegra: apalis_t30: move dr_mode property from phy to controller > ARM: tegra: apalis_t30: reorder backlight properties > ARM: tegra: apalis_t30: drop pwmleds > ARM: tegra: apalis_t30: pinmux clean-up > ARM: tegra: apalis_t30: add missing pinmux > ARM: tegra: apalis_t30: use proper irq-gpio for stmpe811 > ARM: tegra: apalis_t30: further lm95245 temperature sensor annotation > ARM: tegra: apalis_t30: add i2c-thermtrip > ARM: tegra: apalis_t30: add proper emmc vmmc and vqmmc supplies > ARM: tegra: apalis_t30: enable emmc ddr52 mode > ARM: tegra: apalis_t30: get rid of fake clocks simple bus > ARM: tegra: apalis_t30: line break long compatible property line > dt-bindings: add broadcom (formerly plx technology) vendor prefix > ARM: tegra: apalis_t30: drop module level model and compatible > ARM: tegra: apalis_t30: drop obsolete spidev nodes > ARM: tegra: apalis_t30: hog group for pcie switch reset gpio > ARM: tegra: apalis_t30: rename hdmiddc to hdmi_ddc > ARM: tegra: apalis_t30: rename tps65911@2d, stmpe811@41 and > tps62362@60 > ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarity > ARM: tegra: apalis_t30: move hda node from carrier to module > ARM: tegra: apalis_t30: support v1.1 hardware revision > > Documentation/devicetree/bindings/arm/tegra.txt | 2 + > .../devicetree/bindings/vendor-prefixes.txt | 1 + > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/tegra30-apalis-eval.dts | 148 +-- > arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts | 266 +++++ > arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 1189 ++++++++++++++++++++ > arch/arm/boot/dts/tegra30-apalis.dtsi | 705 +++++++++--- > 7 files changed, 2064 insertions(+), 248 deletions(-) > create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts > create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi Applied, thanks. Thierry
This series is a major overhaul and adds support for the V1.1 hardware revision of the Toradex Apalis T30 system on module. Changes in v2: - Clean-up PCIe controller/port status' as well. - Also move serial UART "nvidia,tegra30-hsuart" compatible to module level device trees. - Also add two missing newlines. - Also replace underscores in node names with dashes. - Explicitly disable input of BKL1_ON as well. - Replace underscores in node names with dashes. - When running some more tests I realized that the reg-addr should really be 0x3f. Fix this. - Get rid of fake clocks simple bus as suggested by Rob. - Replace "[PATCH 27/28] ARM: tegra: apalis_t30: fix pcie switch vendor compatible" with "[PATCH v2 26/34] dt-bindings: add broadcom (formerly plx technology) vendor prefix" as suggested by Stefan. - New patch as suggested by Rob. - New patch. - Drop "[PATCH 01/28] ARM: tegra: apalis_t30: enable broken-hpi on emmc" which should already be handled by the broken-hpi quirk as pointed out by Dmitry. If I would find more eMMC parts which exhibit the issue I will add them to the quirk as a separate patch. - Updated V1.1 device trees with all applicable previous fixes. Marcel Ziswiler (34): ARM: tegra: apalis_t30: fix mmc1 cmd pull-up ARM: tegra: apalis_t30: pull-up sd card detect pins ARM: tegra: apalis_t30: add local-mac-address property ARM: tegra: apalis_t30: reorder pcie properties ARM: tegra: apalis_t30: annotate/clean-up pcie controller/port nodes ARM: tegra: apalis_t30: reorder host1x/hdmi properties ARM: tegra: apalis_t30: regulator clean-up ARM: tegra: apalis_t30: add missing regulators ARM: tegra: apalis_t30: annotate uarts and move compatible to board ARM: tegra: apalis_t30: drop unused cami2c label ARM: tegra: apalis_t30: white-space/newline clean-up ARM: tegra: apalis_t30: drop unused mmc1/sd1 labels ARM: tegra: apalis_t30: annotate mmc1/sd1 ARM: tegra: apalis_t30: move dr_mode property from phy to controller ARM: tegra: apalis_t30: reorder backlight properties ARM: tegra: apalis_t30: drop pwmleds ARM: tegra: apalis_t30: pinmux clean-up ARM: tegra: apalis_t30: add missing pinmux ARM: tegra: apalis_t30: use proper irq-gpio for stmpe811 ARM: tegra: apalis_t30: further lm95245 temperature sensor annotation ARM: tegra: apalis_t30: add i2c-thermtrip ARM: tegra: apalis_t30: add proper emmc vmmc and vqmmc supplies ARM: tegra: apalis_t30: enable emmc ddr52 mode ARM: tegra: apalis_t30: get rid of fake clocks simple bus ARM: tegra: apalis_t30: line break long compatible property line dt-bindings: add broadcom (formerly plx technology) vendor prefix ARM: tegra: apalis_t30: drop module level model and compatible ARM: tegra: apalis_t30: drop obsolete spidev nodes ARM: tegra: apalis_t30: hog group for pcie switch reset gpio ARM: tegra: apalis_t30: rename hdmiddc to hdmi_ddc ARM: tegra: apalis_t30: rename tps65911@2d, stmpe811@41 and tps62362@60 ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarity ARM: tegra: apalis_t30: move hda node from carrier to module ARM: tegra: apalis_t30: support v1.1 hardware revision Documentation/devicetree/bindings/arm/tegra.txt | 2 + .../devicetree/bindings/vendor-prefixes.txt | 1 + arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/tegra30-apalis-eval.dts | 148 +-- arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts | 266 +++++ arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 1189 ++++++++++++++++++++ arch/arm/boot/dts/tegra30-apalis.dtsi | 705 +++++++++--- 7 files changed, 2064 insertions(+), 248 deletions(-) create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi