| Message ID | alpine.DEB.2.21.2111201924390.10804@angie.orcam.me.uk |
|---|---|
| State | New |
| Headers | show |
| Series | pci: Work around ASMedia ASM2824 PCIe link training failures | expand |
On Sat, 20 Nov 2021, Maciej W. Rozycki wrote: > One case that has been nurturing me though is the reverse scenario, that > is where the Pericom PI7C9X2G304 switch is upstream while the ASMedia > ASM2824 switch is downstream. Presumably the same situation will happen, > so matching on the ASM2824 ID only would be a problem. Unfortunately the > other device does not implement the Data Link Layer Link Active status > bit, so a more complex approach, such as clearing and then checking for > the Link Bandwidth Management Status having been set again might be an > option. Unlike U-Boot we cannot do aggressive polling of the Link > Training bit. > > Option hardware with M.2 slots is commercially available with the ASM2824 > onboard, so a test environment can be in principle arranged, though I'm > not sure if just for the sake of such an experiment I'm willing to spend > money that will ultimately go to a manufacturer that cannot be bothered to > take responsibility for their faults and at the very least respond to a > problem report. And without verifying the actual problem exists I'm > reluctant to try and implement a workaround. On the other hand the > problem with the Unmatched board is real and this change addresses it, at > least for me. NB I have realised the reverse scenario cannot actually be reproduced with the Delock device as the downstream ports of the PI7C9X2G304 chip appear to have been strapped for 2.5GT/s operation. Or so it seems, as the Pericom datasheet seems unclear about such an option; all it says is: " 7.2.67 LINK CAPABILITIES REGISTER -- OFFSET CCh BIT FUNCTION TYPE DESCRIPTION Indicates the maximum speed of the Express link. 3:0 Maximum Link RO 0001b: 2.5 Gb/s Speed 0010b: 5.0 Gb/s Reset to 0010b. Indicates the maximum width of the given PCIe Link. 9:4 Maximum Link RO Reset to 000010b (x2) for Port 0. Reset to 000001b (x1) for Port 1. Reset to 000001b (x1) for Port 2. " and then: " 7.2.77 LINK CONTROL REGISTER 2 -- OFFSET F0h BIT FUNCTION TYPE DESCRIPTION 3:0 Target Link Speed RWS Reset to 0010b. " so it does tell the upstream port (port 0) and the downstream ports (port 1 & 2) apart where appropriate (link width), but says nothing about any ports capable of being strapped for 2.5GT/s operation. However the actual device reports: 06:01.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G304 EL/SL PCIe2 3-Port/4-Lane Packet Switch [12d8:2304] (rev 05) (prog-if 00 [Normal decode]) [...] Capabilities: [c0] Express (v2) Downstream Port (Slot+), MSI 00 [...] LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM not supported ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp- [...] LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- [...] LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB [...] -- note the discrepancy between the Maximum Link Speed and the Target Link Speed, possibly a device erratum. Also there's no usable Supported Speeds Vector to confirm either way: " 7.2.76 LINK CAPABILITIES REGISTER 2 -- OFFSET ECh BIT FUNCTION TYPE DESCRIPTION 31:0 Link Capabilities 2 RO Reset to 0000_0000h. " It could be possible to verify the reverse scenario perhaps with another manufactured device featuring the PI7C9X2G304 chip though, as they seem somewhat common. Also I got distracted mid-way through my submission and then forgot to mention that I was unable to verify the resume part of this workaround as the Unmatched hardware does not provide such a capability (it's out of scope for this kind of a development/evaluation board). And I have only minimally checked hot-plug operation as I dared not live unplug and replug hardware which may not be prepared for that (I did that once with an ISA board, not exactly on purpose as I didn't realise power was still applied, and all the pieces survived, but the system had to be power-cycled). Removing and rescanning buses behind the ASM2824 switch did work (and triggered rather a surprising oops/panic with the nicstar driver handling an ATM board downstream, which I then had to remove from my configuration for the purpose of this verification), but did not cause the offending link to go down, so the workaround didn't (have to) trigger. Last but not least I have chosen the timeout for retraining somewhat heuristically, so I'll appreciate advice from someone more experienced with PCIe than I am -- most of my involvement in this area so far has been with conventional PCI. Maciej
Index: linux/drivers/pci/quirks.c =================================================================== --- linux.orig/drivers/pci/quirks.c +++ linux/drivers/pci/quirks.c @@ -12,6 +12,7 @@ * file, where their drivers can use them. */ +#include <linux/bug.h> #include <linux/types.h> #include <linux/kernel.h> #include <linux/export.h> @@ -5795,3 +5796,98 @@ static void apex_pci_fixup_class(struct } DECLARE_PCI_FIXUP_CLASS_HEADER(0x1ac1, 0x089a, PCI_CLASS_NOT_DEFINED, 8, apex_pci_fixup_class); + +/* + * Retrain the link of a downstream PCIe port by hand if necessary. + * + * This is needed at least where a downstream port of the ASMedia ASM2824 + * Gen 3 switch is wired to the upstream port of the Pericom PI7C9X2G304 + * Gen 2 switch, and observed with the Delock Riser Card PCI Express x1 > + * 2 x PCIe x1 device, P/N 41433, plugged into the SiFive HiFive Unmatched + * board. + * + * In such a configuration the switches are supposed to negotiate the link + * speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link + * continues switching between the two speeds indefinitely and the data + * link layer never reaches the active state, with link training reported + * repeatedly active ~84% of the time. Forcing the target link speed to + * 2.5GT/s with the upstream ASM2824 device makes the two switches talk to + * each other correctly however. And more interestingly retraining with a + * higher target link speed afterwards lets the two successfully negotiate + * 5.0GT/s. + * + * With the ASM2824 we can rely on the otherwise optional Data Link Layer + * Link Active status bit and in the failed link training scenario it will + * be off along with the Link Bandwidth Management Status indicating that + * hardware has changed the link speed or width in an attempt to correct + * unreliable link operation. For a port that has been left unconnected + * both bits will be clear. So use this information to detect the problem + * rather than polling the Link Training bit and watching out for flips or + * at least the active status. + * + * Restrict the speed to 2.5GT/s then with the Target Link Speed field, + * request a retrain and wait 200ms for the data link to go up. If this + * turns out successful, then lift the restriction, letting the devices + * negotiate a higher speed. Also check for a 2.5GT/s speed restriction + * the firmware may have already arranged and lift it too with ports that + * already report their data link being up. + */ +static void pcie_downstream_link_retrain(struct pci_dev *dev) +{ + u16 lnksta, lnkctl2; + u8 pos; + + pos = pci_find_capability(dev, PCI_CAP_ID_EXP); + BUG_ON(!pos); + + pci_read_config_word(dev, pos + PCI_EXP_LNKCTL2, &lnkctl2); + pci_read_config_word(dev, pos + PCI_EXP_LNKSTA, &lnksta); + if ((lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) == + PCI_EXP_LNKSTA_LBMS) { + unsigned long timeout; + u16 lnkctl; + + pci_info(dev, "broken device, retraining non-functional downstream link at 2.5GT/s...\n"); + + pci_read_config_word(dev, pos + PCI_EXP_LNKCTL, &lnkctl); + lnkctl |= PCI_EXP_LNKCTL_RL; + lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; + lnkctl2 |= PCI_EXP_LNKCTL2_TLS_2_5GT; + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL2, lnkctl2); + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL, lnkctl); + + timeout = jiffies + msecs_to_jiffies(200); + do { + pci_read_config_word(dev, pos + PCI_EXP_LNKSTA, + &lnksta); + if (lnksta & PCI_EXP_LNKSTA_DLLLA) + break; + usleep_range(10000, 20000); + } while (time_before(jiffies, timeout)); + + pci_info(dev, "retraining %s!\n", + lnksta & PCI_EXP_LNKSTA_DLLLA ? + "succeeded" : "failed"); + } + + if ((lnksta & PCI_EXP_LNKSTA_DLLLA) && + (lnkctl2 & PCI_EXP_LNKCTL2_TLS) == PCI_EXP_LNKCTL2_TLS_2_5GT) { + u32 lnkcap; + u16 lnkctl; + + pci_info(dev, "removing 2.5GT/s downstream link speed restriction\n"); + pci_read_config_word(dev, pos + PCI_EXP_LNKCTL, &lnkctl); + pci_read_config_dword(dev, pos + PCI_EXP_LNKCAP, &lnkcap); + lnkctl |= PCI_EXP_LNKCTL_RL; + lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; + lnkctl2 |= lnkcap & PCI_EXP_LNKCAP_SLS; + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL2, lnkctl2); + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL, lnkctl); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ASMEDIA, + PCI_DEVICE_ID_ASMEDIA_ASM2824, + pcie_downstream_link_retrain); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ASMEDIA, + PCI_DEVICE_ID_ASMEDIA_ASM2824, + pcie_downstream_link_retrain); Index: linux/include/linux/pci_ids.h =================================================================== --- linux.orig/include/linux/pci_ids.h +++ linux/include/linux/pci_ids.h @@ -2562,6 +2562,7 @@ #define PCI_SUBDEVICE_ID_QEMU 0x1100 #define PCI_VENDOR_ID_ASMEDIA 0x1b21 +#define PCI_DEVICE_ID_ASMEDIA_ASM2824 0x2824 #define PCI_VENDOR_ID_REDHAT 0x1b36
Attempt to handle cases with a downstream port of the ASMedia ASM2824 PCIe switch where link training never completes and the link continues switching between speeds indefinitely with the data link layer never reaching the active state. It has been observed with a downstream port of the ASMedia ASM2824 Gen 3 switch wired to the upstream port of the Pericom PI7C9X2G304 Gen 2 switch, using a Delock Riser Card PCI Express x1 > 2 x PCIe x1 device, P/N 41433, wired to a SiFive HiFive Unmatched board. In this setup the switches are supposed to negotiate the link speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link continues oscillating between the two speeds, at the rate of 34-35 times per second, with link training reported repeatedly active ~84% of the time, e.g.: 02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode]) [...] Bus: primary=02, secondary=05, subordinate=05, sec-latency=0 [...] Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00 [...] LnkSta: Speed 5GT/s (downgraded), Width x1 (ok) TrErr- Train+ SlotClk+ DLActive- BWMgmt+ ABWMgmt- [...] LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB [...] Forcibly limiting the target link speed to 2.5GT/s with the upstream ASM2824 device makes the two switches communicate correctly however: 02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode]) [...] Bus: primary=02, secondary=05, subordinate=09, sec-latency=0 [...] Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00 [...] LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok) TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- [...] LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB [...] and then: 05:00.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G304 EL/SL PCIe2 3-Port/4-Lane Packet Switch [12d8:2304] (rev 05) (prog-if 00 [Normal decode]) [...] Bus: primary=05, secondary=06, subordinate=09, sec-latency=0 [...] Capabilities: [c0] Express (v2) Upstream Port, MSI 00 [...] LnkSta: Speed 2.5GT/s (downgraded), Width x1 (downgraded) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- [...] LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB [...] Removing the speed restriction afterwards makes the two devices switch to 5.0GT/s then. Make use of these observations then and detect the inability to train the link, by checking for the Data Link Layer Link Active status bit implemented by the ASM2824 being off while the Link Bandwidth Management Status indicating that hardware has changed the link speed or width in an attempt to correct unreliable link operation. Restrict the speed to 2.5GT/s then with the Target Link Speed field, request a retrain and wait 200ms for the data link to go up. If this turns out successful, then lift the restriction, letting the devices negotiate a higher speed. Also check for a 2.5GT/s speed restriction the firmware may have already arranged and lift it too with ports that already report their data link being up. Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> --- Hi, This proposal includes support for a scenario where the firmware has restricted the speed for a port already, for access to any downstream boot devices if nothing else, such as with the U-Boot change proposed here: <https://lists.denx.de/pipermail/u-boot/2021-November/467852.html>. This is why the removal of the 2.5GT/s speed restriction is done regardless of whether it was us to put it in place in the first place. Credit goes to Stefan for a suggestion to check for any interaction with the de-emphasis level, which gave me incentive for further experimentation that has eventually made me discover that lifting the restriction makes the two devices negotiate 5GT/s. This is especially worthwhile given that the Delock part (<https://www.delock.com/produkt/41433/merkmale.html>), since discontinued, has a 5GT/s x1 upstream port and a pair of 2.5GT/s x1 downstream ports so keeping the upstream port at it's maximum speed avoids a bottleneck there. For the background story as to how I tried to get the manufacturers of the devices involved, unsuccessfully, except for the guys from SiFive who were at least sympathetic (thank you!), but this level of hardware debug was beyond their skills and/or resources, and then how I discovered how to persuade the two devices to talk to each other at all, at 2.5GT/s, see: <https://lists.denx.de/pipermail/u-boot/2021-November/467199.html>. One case that has been nurturing me though is the reverse scenario, that is where the Pericom PI7C9X2G304 switch is upstream while the ASMedia ASM2824 switch is downstream. Presumably the same situation will happen, so matching on the ASM2824 ID only would be a problem. Unfortunately the other device does not implement the Data Link Layer Link Active status bit, so a more complex approach, such as clearing and then checking for the Link Bandwidth Management Status having been set again might be an option. Unlike U-Boot we cannot do aggressive polling of the Link Training bit. Option hardware with M.2 slots is commercially available with the ASM2824 onboard, so a test environment can be in principle arranged, though I'm not sure if just for the sake of such an experiment I'm willing to spend money that will ultimately go to a manufacturer that cannot be bothered to take responsibility for their faults and at the very least respond to a problem report. And without verifying the actual problem exists I'm reluctant to try and implement a workaround. On the other hand the problem with the Unmatched board is real and this change addresses it, at least for me. NB the BUG_ON there is a safety valve really for an "impossible" case. The ASM2824 is a PCIe device and necessarily it does have the PCI Express capability. Poking at that unguarded though just didn't feel right to me, while doing any kind of full-fledged recovery seemed like an overkill. Questions, comments, concerns? Otherwise please apply. Maciej --- drivers/pci/quirks.c | 96 ++++++++++++++++++++++++++++++++++++++++++++++++ include/linux/pci_ids.h | 1 2 files changed, 97 insertions(+) linux-pcie-asm2824-manual-retrain.diff