| Message ID | 20240621112915.3434402-3-daire.mcnamara@microchip.com |
|---|---|
| State | New |
| Headers | show |
| Series | Fix address translations on MPFS PCIe controller | expand |
On Fri, 21 Jun 2024, daire.mcnamara@microchip.com wrote: > From: Daire McNamara <daire.mcnamara@microchip.com> > > On Microchip PolarFire SoC the PCIe Root Port can be behind one of three > general purpose Fabric Interface Controller (FIC) buses that encapsulates > an AXI-S bus. Depending on which FIC(s) the Root Port is connected > through to CPU space, and what address translation is done by that FIC, > the Root Port driver's inbound address translation may vary. > > For all current supported designs and all future expected designs, > inbound address translation done by a FIC on PolarFire SoC varies > depending on whether PolarFire SoC in operating in dma-coherent mode or > dma-noncoherent mode. > > The setup of the outbound address translation tables in the root port > driver only needs to handle these two cases. > > Setup the inbound address translation tables to one of two address > translations, depending on whether the rootport is marked as dma-coherent or > dma-noncoherent. > > Fixes: 6f15a9c9f941 ("PCI: microchip: Add Microchip Polarfire PCIe controller driver") > > Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com> Hi, As mentioned against v3 1/3, don't leave empty lines between tags. > --- > drivers/pci/controller/pcie-microchip-host.c | 102 +++++++++++++++++-- > 1 file changed, 93 insertions(+), 9 deletions(-) > > diff --git a/drivers/pci/controller/pcie-microchip-host.c b/drivers/pci/controller/pcie-microchip-host.c > index 853adce24492..d0489bd42bef 100644 > --- a/drivers/pci/controller/pcie-microchip-host.c > +++ b/drivers/pci/controller/pcie-microchip-host.c > @@ -30,6 +30,9 @@ > #define MC_PCIE_BRIDGE_ADDR (MC_PCIE1_BRIDGE_ADDR) > #define MC_PCIE_CTRL_ADDR (MC_PCIE1_CTRL_ADDR) > > +#define MC_MAX_NUM_INBOUND_WINDOWS 8 > +#define MPFS_NC_BOUNCE_ADDR 0x80000000 > + > /* PCIe Bridge Phy Regs */ > #define PCIE_PCI_IRQ_DW0 0xa8 > #define MSIX_CAP_MASK BIT(31) > @@ -97,14 +100,15 @@ > > /* PCIe AXI slave table init defines */ > #define ATR0_AXI4_SLV0_SRCADDR_PARAM 0x800u > -#define ATR_SIZE_SHIFT 1 > -#define ATR_IMPL_ENABLE 1 > +#define ATR_SIZE_MASK GENMASK(6, 1) #include <linux/bits.h> > +#define ATR_IMPL_ENABLE_MASK 1 This would be BIT(0), I think. IMO, you don't need to add _MASK postfix for it, since it's just 1-bit wide field. > #define ATR0_AXI4_SLV0_SRC_ADDR 0x804u > #define ATR0_AXI4_SLV0_TRSL_ADDR_LSB 0x808u > #define ATR0_AXI4_SLV0_TRSL_ADDR_UDW 0x80cu > #define ATR0_AXI4_SLV0_TRSL_PARAM 0x810u > #define PCIE_TX_RX_INTERFACE 0x00000000u > #define PCIE_CONFIG_INTERFACE 0x00000001u > +#define TRSL_ID_AXI4_MASTER_0 0x00000004u > > #define ATR_ENTRY_SIZE 32 > > @@ -931,6 +935,86 @@ static int mc_pcie_init_irq_domains(struct mc_pcie *port) > return mc_allocate_msi_domains(port); > } > > +static void mc_pcie_setup_inbound_atr(int window_index, u64 axi_addr, u64 pcie_addr, size_t size) > +{ > + void __iomem *bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR; > + u32 table_offset = window_index * ATR_ENTRY_SIZE; > + void __iomem *table_addr = bridge_base_addr + table_offset; > + u32 atr_sz; > + u32 val; > + > + atr_sz = ilog2(size) - 1; You should add explicit includes you use: #include <linux/log2.h> > + > + val = ALIGN_DOWN(lower_32_bits(pcie_addr), SZ_4K); #include <linux/align.h> > + val |= FIELD_PREP(ATR_SIZE_MASK, atr_sz); > + val |= FIELD_PREP(ATR_IMPL_ENABLE_MASK, 1); > + > + writel(val, table_addr + ATR0_PCIE_WIN0_SRCADDR_PARAM); > + > + writel(upper_32_bits(pcie_addr), table_addr + ATR0_PCIE_WIN0_SRC_ADDR); #include <linux/wordpart.h> > + writel(lower_32_bits(axi_addr), table_addr + ATR0_PCIE_WIN0_TRSL_ADDR_LSB); > + writel(upper_32_bits(axi_addr), table_addr + ATR0_PCIE_WIN0_TRSL_ADDR_UDW); > + > + writel(TRSL_ID_AXI4_MASTER_0, table_addr + ATR0_PCIE_WIN0_TRSL_PARAM); > +} > + > +static int mc_pcie_setup_inbound_ranges(struct platform_device *pdev, struct mc_pcie *port) > +{ > + struct device *dev = &pdev->dev; > + struct device_node *dn = dev->of_node; > + struct of_range_parser parser; > + struct of_range range; > + int atr_index = 0; > + > + /* > + * MPFS PCIe root port is 32-bit only, behind a Fabric Interface > + * Controller FPGA logic block which contains the AXI-S interface. > + * > + * From the point of view of the PCIe root port, There are only > + * two supported Root Port configurations > + * > + * Configuration 1: for use with fully coherent designs; supports a > + * window from 0x0 (CPU space) to specified PCIe space. > + * > + * Configuration 2: for use with non-coherent designs; supports two > + * 1 Gb wide windows to CPU space; one mapping cpu space 0 to pcie > + * space 0x80000000 and mapping cpu space 0x40000000 to pcie > + * space 0xc0000000. This cfg needs two windows because of how > + * the MSI space is allocated in the AXI-S range on MPFS. > + * > + * The FIC interface outside the PCIe block *must* complete the inbound > + * address translation as per MCHP MPFS FPGA design guidelines. > + */ > + if (device_property_read_bool(dev, "dma-noncoherent")) { > + /* > + * Always need same two tables in this case. Need two tables > + * due to hardware interactions between address and size. > + */ > + mc_pcie_setup_inbound_atr(0, 0, MPFS_NC_BOUNCE_ADDR, SZ_1G); > + mc_pcie_setup_inbound_atr(1, SZ_1G, MPFS_NC_BOUNCE_ADDR + SZ_1G, SZ_1G); > + } else { > + /* Find any dma-ranges */ > + if (of_pci_dma_range_parser_init(&parser, dn)) { > + /* No dma-range property - setup default */ > + mc_pcie_setup_inbound_atr(0, 0, 0, SZ_4G); > + return 0; > + } > + > + for_each_of_range(&parser, &range) { > + if (atr_index >= MC_MAX_NUM_INBOUND_WINDOWS) { > + dev_err(dev, "too many inbound ranges; %d available tables\n", > + MC_MAX_NUM_INBOUND_WINDOWS); > + return -EINVAL; > + } > + mc_pcie_setup_inbound_atr(atr_index, 0, range.pci_addr, range.size); > + atr_index++; > + } > + } > + > + return 0; > +} > + > static void mc_pcie_setup_window(void __iomem *bridge_base_addr, u32 index, > phys_addr_t axi_addr, phys_addr_t pci_addr, > u64 size) > @@ -946,8 +1030,9 @@ static void mc_pcie_setup_window(void __iomem *bridge_base_addr, u32 index, > writel(val, bridge_base_addr + (index * ATR_ENTRY_SIZE) + > ATR0_AXI4_SLV0_TRSL_PARAM); > > - val = lower_32_bits(axi_addr) | (atr_sz << ATR_SIZE_SHIFT) | > - ATR_IMPL_ENABLE; > + val = ALIGN_DOWN(lower_32_bits(axi_addr), SZ_4K); > + val |= FIELD_PREP(ATR_SIZE_MASK, atr_sz); > + val |= FIELD_PREP(ATR_IMPL_ENABLE_MASK, 1); This can be just val |= ATR_IMPL_ENABLE when you don't have _MASK there which is easier to read (IMO). It would be nice to put the GENMASK()/FIELD_PREP() refactor into a preparatory patch on top of which you'd make the actual fix to keep the fix change itself simpler. Nonetheless, this was already much better than the previous version.
diff --git a/drivers/pci/controller/pcie-microchip-host.c b/drivers/pci/controller/pcie-microchip-host.c index 853adce24492..d0489bd42bef 100644 --- a/drivers/pci/controller/pcie-microchip-host.c +++ b/drivers/pci/controller/pcie-microchip-host.c @@ -30,6 +30,9 @@ #define MC_PCIE_BRIDGE_ADDR (MC_PCIE1_BRIDGE_ADDR) #define MC_PCIE_CTRL_ADDR (MC_PCIE1_CTRL_ADDR) +#define MC_MAX_NUM_INBOUND_WINDOWS 8 +#define MPFS_NC_BOUNCE_ADDR 0x80000000 + /* PCIe Bridge Phy Regs */ #define PCIE_PCI_IRQ_DW0 0xa8 #define MSIX_CAP_MASK BIT(31) @@ -97,14 +100,15 @@ /* PCIe AXI slave table init defines */ #define ATR0_AXI4_SLV0_SRCADDR_PARAM 0x800u -#define ATR_SIZE_SHIFT 1 -#define ATR_IMPL_ENABLE 1 +#define ATR_SIZE_MASK GENMASK(6, 1) +#define ATR_IMPL_ENABLE_MASK 1 #define ATR0_AXI4_SLV0_SRC_ADDR 0x804u #define ATR0_AXI4_SLV0_TRSL_ADDR_LSB 0x808u #define ATR0_AXI4_SLV0_TRSL_ADDR_UDW 0x80cu #define ATR0_AXI4_SLV0_TRSL_PARAM 0x810u #define PCIE_TX_RX_INTERFACE 0x00000000u #define PCIE_CONFIG_INTERFACE 0x00000001u +#define TRSL_ID_AXI4_MASTER_0 0x00000004u #define ATR_ENTRY_SIZE 32 @@ -931,6 +935,86 @@ static int mc_pcie_init_irq_domains(struct mc_pcie *port) return mc_allocate_msi_domains(port); } +static void mc_pcie_setup_inbound_atr(int window_index, u64 axi_addr, u64 pcie_addr, size_t size) +{ + void __iomem *bridge_base_addr = port->axi_base_addr + MC_PCIE_BRIDGE_ADDR; + u32 table_offset = window_index * ATR_ENTRY_SIZE; + void __iomem *table_addr = bridge_base_addr + table_offset; + u32 atr_sz; + u32 val; + + atr_sz = ilog2(size) - 1; + + val = ALIGN_DOWN(lower_32_bits(pcie_addr), SZ_4K); + val |= FIELD_PREP(ATR_SIZE_MASK, atr_sz); + val |= FIELD_PREP(ATR_IMPL_ENABLE_MASK, 1); + + writel(val, table_addr + ATR0_PCIE_WIN0_SRCADDR_PARAM); + + writel(upper_32_bits(pcie_addr), table_addr + ATR0_PCIE_WIN0_SRC_ADDR); + + writel(lower_32_bits(axi_addr), table_addr + ATR0_PCIE_WIN0_TRSL_ADDR_LSB); + writel(upper_32_bits(axi_addr), table_addr + ATR0_PCIE_WIN0_TRSL_ADDR_UDW); + + writel(TRSL_ID_AXI4_MASTER_0, table_addr + ATR0_PCIE_WIN0_TRSL_PARAM); +} + +static int mc_pcie_setup_inbound_ranges(struct platform_device *pdev, struct mc_pcie *port) +{ + struct device *dev = &pdev->dev; + struct device_node *dn = dev->of_node; + struct of_range_parser parser; + struct of_range range; + int atr_index = 0; + + /* + * MPFS PCIe root port is 32-bit only, behind a Fabric Interface + * Controller FPGA logic block which contains the AXI-S interface. + * + * From the point of view of the PCIe root port, There are only + * two supported Root Port configurations + * + * Configuration 1: for use with fully coherent designs; supports a + * window from 0x0 (CPU space) to specified PCIe space. + * + * Configuration 2: for use with non-coherent designs; supports two + * 1 Gb wide windows to CPU space; one mapping cpu space 0 to pcie + * space 0x80000000 and mapping cpu space 0x40000000 to pcie + * space 0xc0000000. This cfg needs two windows because of how + * the MSI space is allocated in the AXI-S range on MPFS. + * + * The FIC interface outside the PCIe block *must* complete the inbound + * address translation as per MCHP MPFS FPGA design guidelines. + */ + if (device_property_read_bool(dev, "dma-noncoherent")) { + /* + * Always need same two tables in this case. Need two tables + * due to hardware interactions between address and size. + */ + mc_pcie_setup_inbound_atr(0, 0, MPFS_NC_BOUNCE_ADDR, SZ_1G); + mc_pcie_setup_inbound_atr(1, SZ_1G, MPFS_NC_BOUNCE_ADDR + SZ_1G, SZ_1G); + } else { + /* Find any dma-ranges */ + if (of_pci_dma_range_parser_init(&parser, dn)) { + /* No dma-range property - setup default */ + mc_pcie_setup_inbound_atr(0, 0, 0, SZ_4G); + return 0; + } + + for_each_of_range(&parser, &range) { + if (atr_index >= MC_MAX_NUM_INBOUND_WINDOWS) { + dev_err(dev, "too many inbound ranges; %d available tables\n", + MC_MAX_NUM_INBOUND_WINDOWS); + return -EINVAL; + } + mc_pcie_setup_inbound_atr(atr_index, 0, range.pci_addr, range.size); + atr_index++; + } + } + + return 0; +} + static void mc_pcie_setup_window(void __iomem *bridge_base_addr, u32 index, phys_addr_t axi_addr, phys_addr_t pci_addr, u64 size) @@ -946,8 +1030,9 @@ static void mc_pcie_setup_window(void __iomem *bridge_base_addr, u32 index, writel(val, bridge_base_addr + (index * ATR_ENTRY_SIZE) + ATR0_AXI4_SLV0_TRSL_PARAM); - val = lower_32_bits(axi_addr) | (atr_sz << ATR_SIZE_SHIFT) | - ATR_IMPL_ENABLE; + val = ALIGN_DOWN(lower_32_bits(axi_addr), SZ_4K); + val |= FIELD_PREP(ATR_SIZE_MASK, atr_sz); + val |= FIELD_PREP(ATR_IMPL_ENABLE_MASK, 1); writel(val, bridge_base_addr + (index * ATR_ENTRY_SIZE) + ATR0_AXI4_SLV0_SRCADDR_PARAM); @@ -962,11 +1047,6 @@ static void mc_pcie_setup_window(void __iomem *bridge_base_addr, u32 index, val = upper_32_bits(pci_addr); writel(val, bridge_base_addr + (index * ATR_ENTRY_SIZE) + ATR0_AXI4_SLV0_TRSL_ADDR_UDW); - - val = readl(bridge_base_addr + ATR0_PCIE_WIN0_SRCADDR_PARAM); - val |= (ATR0_PCIE_ATR_SIZE << ATR0_PCIE_ATR_SIZE_SHIFT); - writel(val, bridge_base_addr + ATR0_PCIE_WIN0_SRCADDR_PARAM); - writel(0, bridge_base_addr + ATR0_PCIE_WIN0_SRC_ADDR); } static int mc_pcie_setup_windows(struct platform_device *pdev, @@ -1129,6 +1209,10 @@ static int mc_platform_init(struct pci_config_window *cfg) if (ret) return ret; + ret = mc_pcie_setup_inbound_ranges(pdev, port); + if (ret) + return ret; + /* Address translation is up; safe to enable interrupts */ ret = mc_init_interrupts(pdev, port); if (ret)