@@ -1369,10 +1369,14 @@ struct qmp_phy_cfg {
/* Init sequence for PHY blocks - serdes, tx, rx, pcs */
struct qmp_phy_cfg_tables primary;
/*
- * Init sequence for PHY blocks, providing additional register
- * programming. Unless required it can be left omitted.
+ * Init sequences for PHY blocks, providing additional register
+ * programming. They are used for providing separate sequences for the
+ * Root Complex and for the End Point usecases.
+ *
+ * If EP mode is not supported, both tables can be left empty.
*/
- struct qmp_phy_cfg_tables secondary;
+ struct qmp_phy_cfg_tables secondary_rc; /* for the RC only */
+ struct qmp_phy_cfg_tables secondary_ep; /* for the EP only */
/* clock ids to be requested */
const char * const *clk_list;
@@ -1422,6 +1426,7 @@ struct qmp_phy_cfg {
* @index: lane index
* @qmp: QMP phy to which this lane belongs
* @mode: current PHY mode
+ * @secondary: currently selected PHY secondary init table set
*/
struct qmp_phy {
struct phy *phy;
@@ -1434,6 +1439,7 @@ struct qmp_phy {
void __iomem *rx2;
void __iomem *pcs_misc;
struct clk *pipe_clk;
+ const struct qmp_phy_cfg_tables *secondary;
unsigned int index;
struct qcom_qmp *qmp;
enum phy_mode mode;
@@ -1687,7 +1693,15 @@ static const struct qmp_phy_cfg sm8250_qmp_gen3x1_pciephy_cfg = {
.pcs_misc_tbl = sm8250_qmp_pcie_pcs_misc_tbl,
.pcs_misc_tbl_num = ARRAY_SIZE(sm8250_qmp_pcie_pcs_misc_tbl),
},
- .secondary = {
+ /*
+ * For sm8250 the split between the primary and secondary_rc tables is
+ * historical, it reflects the programming sequence common to all PCIe
+ * PHYs on this platform and a sequence required for this particular
+ * PHY type. If EP support for sm8250 is required, the
+ * primary/secondary_rc split is to be reconsidered and adjusted
+ * according to EP programming sequence.
+ */
+ .secondary_rc = {
.serdes_tbl = sm8250_qmp_gen3x1_pcie_serdes_tbl,
.serdes_tbl_num = ARRAY_SIZE(sm8250_qmp_gen3x1_pcie_serdes_tbl),
.rx_tbl = sm8250_qmp_gen3x1_pcie_rx_tbl,
@@ -1730,7 +1744,15 @@ static const struct qmp_phy_cfg sm8250_qmp_gen3x2_pciephy_cfg = {
.pcs_misc_tbl = sm8250_qmp_pcie_pcs_misc_tbl,
.pcs_misc_tbl_num = ARRAY_SIZE(sm8250_qmp_pcie_pcs_misc_tbl),
},
- .secondary = {
+ /*
+ * For sm8250 the split between the primary and secondary_rc tables is
+ * historical, it reflects the programming sequence common to all PCIe
+ * PHYs on this platform and a sequence required for this particular
+ * PHY type. If EP support for sm8250 is required, the
+ * primary/secondary_rc split is to be reconsidered and adjusted
+ * according to EP programming sequence.
+ */
+ .secondary_rc = {
.tx_tbl = sm8250_qmp_gen3x2_pcie_tx_tbl,
.tx_tbl_num = ARRAY_SIZE(sm8250_qmp_gen3x2_pcie_tx_tbl),
.rx_tbl = sm8250_qmp_gen3x2_pcie_rx_tbl,
@@ -1955,7 +1977,7 @@ static int qcom_qmp_phy_pcie_serdes_init(struct qmp_phy *qphy)
void __iomem *serdes = qphy->serdes;
qcom_qmp_phy_pcie_configure(serdes, cfg->regs, cfg->primary.serdes_tbl, cfg->primary.serdes_tbl_num);
- qcom_qmp_phy_pcie_configure(serdes, cfg->regs, cfg->secondary.serdes_tbl, cfg->secondary.serdes_tbl_num);
+ qcom_qmp_phy_pcie_configure(serdes, cfg->regs, qphy->secondary->serdes_tbl, qphy->secondary->serdes_tbl_num);
return 0;
}
@@ -2049,6 +2071,10 @@ static int qcom_qmp_phy_pcie_power_on(struct phy *phy)
unsigned int mask, val, ready;
int ret;
+ /* Default to RC mode if the mode was not selected using phy_set_mode_ext() */
+ if (!qphy->secondary)
+ qphy->secondary = &cfg->secondary_rc;
+
qcom_qmp_phy_pcie_serdes_init(qphy);
ret = clk_prepare_enable(qphy->pipe_clk);
@@ -2061,39 +2087,39 @@ static int qcom_qmp_phy_pcie_power_on(struct phy *phy)
qcom_qmp_phy_pcie_configure_lane(tx, cfg->regs,
cfg->primary.tx_tbl, cfg->primary.tx_tbl_num, 1);
qcom_qmp_phy_pcie_configure_lane(tx, cfg->regs,
- cfg->secondary.tx_tbl, cfg->secondary.tx_tbl_num, 1);
+ qphy->secondary->tx_tbl, qphy->secondary->tx_tbl_num, 1);
/* Configuration for other LANE for USB-DP combo PHY */
if (cfg->is_dual_lane_phy) {
qcom_qmp_phy_pcie_configure_lane(qphy->tx2, cfg->regs,
cfg->primary.tx_tbl, cfg->primary.tx_tbl_num, 2);
qcom_qmp_phy_pcie_configure_lane(qphy->tx2, cfg->regs,
- cfg->secondary.tx_tbl, cfg->secondary.tx_tbl_num, 2);
+ qphy->secondary->tx_tbl, qphy->secondary->tx_tbl_num, 2);
}
qcom_qmp_phy_pcie_configure_lane(rx, cfg->regs,
cfg->primary.rx_tbl, cfg->primary.rx_tbl_num, 1);
qcom_qmp_phy_pcie_configure_lane(rx, cfg->regs,
- cfg->secondary.rx_tbl, cfg->secondary.rx_tbl_num, 1);
+ qphy->secondary->rx_tbl, qphy->secondary->rx_tbl_num, 1);
if (cfg->is_dual_lane_phy) {
qcom_qmp_phy_pcie_configure_lane(qphy->rx2, cfg->regs,
cfg->primary.rx_tbl, cfg->primary.rx_tbl_num, 2);
qcom_qmp_phy_pcie_configure_lane(qphy->rx2, cfg->regs,
- cfg->secondary.rx_tbl, cfg->secondary.rx_tbl_num, 2);
+ qphy->secondary->rx_tbl, qphy->secondary->rx_tbl_num, 2);
}
qcom_qmp_phy_pcie_configure(pcs, cfg->regs,
cfg->primary.pcs_tbl, cfg->primary.pcs_tbl_num);
qcom_qmp_phy_pcie_configure(pcs, cfg->regs,
- cfg->secondary.pcs_tbl, cfg->secondary.pcs_tbl_num);
+ qphy->secondary->pcs_tbl, qphy->secondary->pcs_tbl_num);
qcom_qmp_phy_pcie_configure(pcs_misc, cfg->regs,
cfg->primary.pcs_misc_tbl,
cfg->primary.pcs_misc_tbl_num);
qcom_qmp_phy_pcie_configure(pcs_misc, cfg->regs,
- cfg->secondary.pcs_misc_tbl,
- cfg->secondary.pcs_misc_tbl_num);
+ qphy->secondary->pcs_misc_tbl,
+ qphy->secondary->pcs_misc_tbl_num);
/*
* Pull out PHY from POWER DOWN state.
@@ -2195,6 +2221,11 @@ static int qcom_qmp_phy_pcie_set_mode(struct phy *phy,
qphy->mode = mode;
+ if (submode)
+ qphy->secondary = &qphy->cfg->secondary_ep;
+ else
+ qphy->secondary = &qphy->cfg->secondary_rc;
+
return 0;
}
The PCIe QMP PHY requires different programming sequences when being used for the RC (Root Complex) or for the EP (End Point) modes. Allow selecting the submode and thus selecting a set of PHY programming tables. Since the RC and EP modes share common some common init sequence, the common sequence is kept in the primary table and the different ones were in secondary. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 57 ++++++++++++++++++------ 1 file changed, 44 insertions(+), 13 deletions(-)