| Message ID | 20200410004738.19668-2-ansuelsmth@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | Move tx-deempth and tx swing to pci.txt | expand |
On 4/9/2020 5:47 PM, Ansuel Smith wrote: > Document tx-deempth, tx swing and rx-eq property property used on some > device (qcom ipq806x or imx6q) to tune and fix init error of the pci > bridge. Those properties are not specific to the host bridge per-se, but to the PCIe PHY, therefore, one would expect to find those properties within the PCIe PHY node if it exists. Given you want this binding to be generic, this is an important thing to correct here.
Looks like "dt-bindings: PCI: " is the convention here. $ git log --oneline Documentation/devicetree/bindings/pci/ 11be8af70d86 dt-bindings: PCI: Convert PCIe Host/Endpoint in Cadence platform to DT schema 69501078fc60 dt-bindings: PCI: cadence: Add PCIe RC/EP DT schema for Cadence PCIe 847dbf4e1aba dt-bindings: PCI: Add PCI Endpoint Controller Schema f9f711efd441 arm64: tegra: Fix Tegra194 PCIe compatible string 9f04d18b1edf dt-bindings: PCI: tegra: Add DT support for PCIe EP nodes in Tegra194 6e5f77031cc9 dt-bindings: PCI: meson: Update PCIE bindings documentation 3edeb49525bb dt-bindings: PCI: Add NXP Layerscape SoCs PCIe Gen4 controller 34129bb831cc dt-bindings: PCI: intel: Fix dt_binding_check compilation failure On Fri, Apr 10, 2020 at 02:47:35AM +0200, Ansuel Smith wrote: > Document tx-deempth, tx swing and rx-eq property property used on some > device (qcom ipq806x or imx6q) to tune and fix init error of the pci > bridge. s/tx-deempth/tx-deemph/ (in subject and commit log) s/tx swing/tx-swing/ (both places also) s/rx-eq/rx-equalization/ (ditto) s/property property/properties/ s/pci/PCI/ in English text (not C variables, function names, etc). If these are made generic, remove the "qcom ipq806x or imx6q" part. > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> > --- > Documentation/devicetree/bindings/pci/pci.txt | 18 ++++++++++++++++++ > 1 file changed, 18 insertions(+) > > diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt > index 29bcbd88f457..df37486f1853 100644 > --- a/Documentation/devicetree/bindings/pci/pci.txt > +++ b/Documentation/devicetree/bindings/pci/pci.txt > @@ -24,6 +24,24 @@ driver implementation may support the following properties: > unsupported link speed, for instance, trying to do training for > unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' > for gen2, and '1' for gen1. Any other values are invalid. > +- tx-deemph-gen1 > + If present this property will tune the Transmit De-Emphasis level for GEN1 if > + supported by the driver. > +- tx-deemph-gen2-3p5db > + If present this property will tune the Transmit De-Emphasis level for GEN2 in > + 3.5db band if supported by the driver. > +- tx-deempth-gen2-6db > + If present this property will tune the Transmit De-Emphasis level for GEN2 in > + 6db band if supported by the driver. > +- tx-swing-full > + If present this property will tune the Tx Swing Full value if supported by the > + driver. > +- tx-swing-low > + If present this property will tune the Tx Swing Low value if supported by the Wrap all of these to fit in 78 columns. Some of them fit in 80 columns, which is sort of OK. This one is 81, which is definitely too long. > + driver. > +- rx-equalization > + If present this property will tune the Rx equalization value if supported by > + the driver. > - reset-gpios: > If present this property specifies PERST# GPIO. Host drivers can parse the > GPIO and apply fundamental reset to endpoints. > -- > 2.25.1 >
> On 4/9/2020 5:47 PM, Ansuel Smith wrote: > > Document tx-deempth, tx swing and rx-eq property property used on > some > > device (qcom ipq806x or imx6q) to tune and fix init error of the pci > > bridge. > > Those properties are not specific to the host bridge per-se, but to the > PCIe PHY, therefore, one would expect to find those properties within > the PCIe PHY node if it exists. Given you want this binding to be > generic, this is an important thing to correct here. > -- > Florian So where should I put these? If I understand this properly I should move this to the PHY directory but no PCIe PHY node exist for both imx6q and ipq806x. How I should proceed? It would be better to just drop this and add qcom specific binding to the driver?
diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 29bcbd88f457..df37486f1853 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -24,6 +24,24 @@ driver implementation may support the following properties: unsupported link speed, for instance, trying to do training for unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' for gen2, and '1' for gen1. Any other values are invalid. +- tx-deemph-gen1 + If present this property will tune the Transmit De-Emphasis level for GEN1 if + supported by the driver. +- tx-deemph-gen2-3p5db + If present this property will tune the Transmit De-Emphasis level for GEN2 in + 3.5db band if supported by the driver. +- tx-deempth-gen2-6db + If present this property will tune the Transmit De-Emphasis level for GEN2 in + 6db band if supported by the driver. +- tx-swing-full + If present this property will tune the Tx Swing Full value if supported by the + driver. +- tx-swing-low + If present this property will tune the Tx Swing Low value if supported by the + driver. +- rx-equalization + If present this property will tune the Rx equalization value if supported by + the driver. - reset-gpios: If present this property specifies PERST# GPIO. Host drivers can parse the GPIO and apply fundamental reset to endpoints.
Document tx-deempth, tx swing and rx-eq property property used on some device (qcom ipq806x or imx6q) to tune and fix init error of the pci bridge. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- Documentation/devicetree/bindings/pci/pci.txt | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)