| Message ID | 20210104152909.22038-1-kishon@ti.com |
|---|---|
| Headers | show |
| Series | Implement NTB Controller using multiple PCI EP | expand |
+MAINTAINERS for platforms supporting PCIe EP mode Hi All, I've looped you in since the platform you maintain supports PCIe EP mode. This series builds NTB functionality on top of PCIe endpoint framework. For NTB functionality it needs atleast two endpoint instances. I'm trying to see if someone can help me test this series in any of the platforms you support. Even if your platform cannot enable NTB, if you can just apply this patch series and test pci_epf_test that would be very much helpful. Thanks in advance for your help. Best Regards, Kishon On 04/01/21 8:58 pm, Kishon Vijay Abraham I wrote: > This series is about implementing SW defined Non-Transparent Bridge (NTB) > using multiple endpoint (EP) instances. This series has been tested using > 2 endpoint instances in J7 connected to J7 board on one end and DRA7 board > on the other end. However there is nothing platform specific for the NTB > functionality. > > This was presented in Linux Plumbers Conference. Link to presentation > and video can be found @ [1] > Created a video demo @ [9] > > RFC patch series can be found @ [2] > v1 patch series can be found @ [3] > v2 patch series can be found @ [4] > v3 patch series can be found @ [5] > v4 patch series can be found @ [6] > v5 patch series can be found @ [7] > v6 patch series can be found @ [8] > v7 patch series can be found @ [10] > v8 patch series can be found @ [11] > > Changes from v8: > 1) Do not use devm_request_irq/devm_free_irq as pci_free_irq_vectors() > has to be used after free_irq > 2) Drop "NTB: tool: Enable the NTB/PCIe link on the local or remote side > of bridge" as there is a debugfs entry to enable the link > > Changes from v7: > 1) Used values stored in ctrl_reg_bar, peer_spad_reg_bar and db_reg_bar > instead of hardcoded values in pci_iomap of ntb_hw_epf.c driver > > Changes from v6: > 1) Fixed issues when multiple NTB devices are creating using multiple > functions > 2) Fixed issue with writing scratchpad register > 3) Created a video demo @ [9] > > Changes from v5: > 1) Fixed a formatting issue in Kconfig pointed out by Randy > 2) Checked for Error or Null in pci_epc_add_epf() > > Changes from v4: > 1) Fixed error condition checks in pci_epc_add_epf() > > Changes from v3: > 1) Fixed Documentation edits suggested by Randy Dunlap <rdunlap@infradead.org> > > Changes from v2: > 1) Add support for the user to create sub-directory of 'EPF Device' > directory (for endpoint function specific configuration using > configfs). > 2) Add documentation for NTB specific attributes in configfs > 3) Check for PCI_CLASS_MEMORY_RAM (PCIe class) before binding ntb_hw_epf > driver > 4) Other documentation fixes > > Changes from v1: > 1) As per Rob's comment, removed support for creating NTB function > device from DT > 2) Add support to create NTB EPF device using configfs (added support in > configfs to associate primary and secondary EPC with EPF. > > Changes from RFC: > 1) Converted the DT binding patches to YAML schema and merged the > DT binding patches together > 2) NTB documentation is converted to .rst > 3) One HOST can now interrupt the other HOST using MSI-X interrupts > 4) Added support for teardown of memory window and doorbell > configuration > 5) Add support to provide support 64-bit memory window size from > DT > > [1] -> https://linuxplumbersconf.org/event/4/contributions/395/ > [2] -> http://lore.kernel.org/r/20190926112933.8922-1-kishon@ti.com > [3] -> http://lore.kernel.org/r/20200514145927.17555-1-kishon@ti.com > [4] -> http://lore.kernel.org/r/20200611130525.22746-1-kishon@ti.com > [5] -> http://lore.kernel.org/r/20200904075052.8911-1-kishon@ti.com > [6] -> http://lore.kernel.org/r/20200915042110.3015-1-kishon@ti.com > [7] -> http://lore.kernel.org/r/20200918064227.1463-1-kishon@ti.com > [8] -> http://lore.kernel.org/r/20200924092519.17082-1-kishon@ti.com > [9] -> https://youtu.be/dLKKxrg5-rY > [10] -> http://lore.kernel.org/r/20200930153519.7282-1-kishon@ti.com > [11] -> http://lore.kernel.org/r/20201111153559.19050-1-kishon@ti.com > > Kishon Vijay Abraham I (17): > Documentation: PCI: Add specification for the *PCI NTB* function > device > PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit > BAR > PCI: endpoint: Add helper API to get the 'next' unreserved BAR > PCI: endpoint: Make *_free_bar() to return error codes on failure > PCI: endpoint: Remove unused pci_epf_match_device() > PCI: endpoint: Add support to associate secondary EPC with EPF > PCI: endpoint: Add support in configfs to associate two EPCs with EPF > PCI: endpoint: Add pci_epc_ops to map MSI irq > PCI: endpoint: Add pci_epf_ops for epf drivers to expose function > specific attrs > PCI: endpoint: Allow user to create sub-directory of 'EPF Device' > directory > PCI: cadence: Implement ->msi_map_irq() ops > PCI: cadence: Configure LM_EP_FUNC_CFG based on epc->function_num_map > PCI: endpoint: Add EP function driver to provide NTB functionality > PCI: Add TI J721E device to pci ids > NTB: Add support for EPF PCI-Express Non-Transparent Bridge > Documentation: PCI: Add configfs binding documentation for pci-ntb > endpoint function > Documentation: PCI: Add userguide for PCI endpoint NTB function > > .../PCI/endpoint/function/binding/pci-ntb.rst | 38 + > Documentation/PCI/endpoint/index.rst | 3 + > .../PCI/endpoint/pci-endpoint-cfs.rst | 10 + > .../PCI/endpoint/pci-ntb-function.rst | 351 +++ > Documentation/PCI/endpoint/pci-ntb-howto.rst | 160 ++ > drivers/misc/pci_endpoint_test.c | 1 - > drivers/ntb/hw/Kconfig | 1 + > drivers/ntb/hw/Makefile | 1 + > drivers/ntb/hw/epf/Kconfig | 6 + > drivers/ntb/hw/epf/Makefile | 1 + > drivers/ntb/hw/epf/ntb_hw_epf.c | 754 ++++++ > .../pci/controller/cadence/pcie-cadence-ep.c | 60 +- > drivers/pci/endpoint/functions/Kconfig | 12 + > drivers/pci/endpoint/functions/Makefile | 1 + > drivers/pci/endpoint/functions/pci-epf-ntb.c | 2114 +++++++++++++++++ > drivers/pci/endpoint/functions/pci-epf-test.c | 13 +- > drivers/pci/endpoint/pci-ep-cfs.c | 176 +- > drivers/pci/endpoint/pci-epc-core.c | 130 +- > drivers/pci/endpoint/pci-epf-core.c | 105 +- > include/linux/pci-epc.h | 39 +- > include/linux/pci-epf.h | 28 +- > include/linux/pci_ids.h | 1 + > 22 files changed, 3932 insertions(+), 73 deletions(-) > create mode 100644 Documentation/PCI/endpoint/function/binding/pci-ntb.rst > create mode 100644 Documentation/PCI/endpoint/pci-ntb-function.rst > create mode 100644 Documentation/PCI/endpoint/pci-ntb-howto.rst > create mode 100644 drivers/ntb/hw/epf/Kconfig > create mode 100644 drivers/ntb/hw/epf/Makefile > create mode 100644 drivers/ntb/hw/epf/ntb_hw_epf.c > create mode 100644 drivers/pci/endpoint/functions/pci-epf-ntb.c >
Hi, On 04/01/21 9:16 pm, Kishon Vijay Abraham I wrote: > +MAINTAINERS for platforms supporting PCIe EP mode > > Hi All, > > I've looped you in since the platform you maintain supports PCIe EP > mode. This series builds NTB functionality on top of PCIe endpoint > framework. For NTB functionality it needs atleast two endpoint > instances. I'm trying to see if someone can help me test this series in > any of the platforms you support. > > Even if your platform cannot enable NTB, if you can just apply this > patch series and test pci_epf_test that would be very much helpful. > > Thanks in advance for your help. Gentle ping for providing your "Reviewed-by" and "Tested-by". Thank You, Kishon > > Best Regards, > Kishon > > On 04/01/21 8:58 pm, Kishon Vijay Abraham I wrote: >> This series is about implementing SW defined Non-Transparent Bridge (NTB) >> using multiple endpoint (EP) instances. This series has been tested using >> 2 endpoint instances in J7 connected to J7 board on one end and DRA7 board >> on the other end. However there is nothing platform specific for the NTB >> functionality. >> >> This was presented in Linux Plumbers Conference. Link to presentation >> and video can be found @ [1] >> Created a video demo @ [9] >> >> RFC patch series can be found @ [2] >> v1 patch series can be found @ [3] >> v2 patch series can be found @ [4] >> v3 patch series can be found @ [5] >> v4 patch series can be found @ [6] >> v5 patch series can be found @ [7] >> v6 patch series can be found @ [8] >> v7 patch series can be found @ [10] >> v8 patch series can be found @ [11] >> >> Changes from v8: >> 1) Do not use devm_request_irq/devm_free_irq as pci_free_irq_vectors() >> has to be used after free_irq >> 2) Drop "NTB: tool: Enable the NTB/PCIe link on the local or remote side >> of bridge" as there is a debugfs entry to enable the link >> >> Changes from v7: >> 1) Used values stored in ctrl_reg_bar, peer_spad_reg_bar and db_reg_bar >> instead of hardcoded values in pci_iomap of ntb_hw_epf.c driver >> >> Changes from v6: >> 1) Fixed issues when multiple NTB devices are creating using multiple >> functions >> 2) Fixed issue with writing scratchpad register >> 3) Created a video demo @ [9] >> >> Changes from v5: >> 1) Fixed a formatting issue in Kconfig pointed out by Randy >> 2) Checked for Error or Null in pci_epc_add_epf() >> >> Changes from v4: >> 1) Fixed error condition checks in pci_epc_add_epf() >> >> Changes from v3: >> 1) Fixed Documentation edits suggested by Randy Dunlap <rdunlap@infradead.org> >> >> Changes from v2: >> 1) Add support for the user to create sub-directory of 'EPF Device' >> directory (for endpoint function specific configuration using >> configfs). >> 2) Add documentation for NTB specific attributes in configfs >> 3) Check for PCI_CLASS_MEMORY_RAM (PCIe class) before binding ntb_hw_epf >> driver >> 4) Other documentation fixes >> >> Changes from v1: >> 1) As per Rob's comment, removed support for creating NTB function >> device from DT >> 2) Add support to create NTB EPF device using configfs (added support in >> configfs to associate primary and secondary EPC with EPF. >> >> Changes from RFC: >> 1) Converted the DT binding patches to YAML schema and merged the >> DT binding patches together >> 2) NTB documentation is converted to .rst >> 3) One HOST can now interrupt the other HOST using MSI-X interrupts >> 4) Added support for teardown of memory window and doorbell >> configuration >> 5) Add support to provide support 64-bit memory window size from >> DT >> >> [1] -> https://linuxplumbersconf.org/event/4/contributions/395/ >> [2] -> http://lore.kernel.org/r/20190926112933.8922-1-kishon@ti.com >> [3] -> http://lore.kernel.org/r/20200514145927.17555-1-kishon@ti.com >> [4] -> http://lore.kernel.org/r/20200611130525.22746-1-kishon@ti.com >> [5] -> http://lore.kernel.org/r/20200904075052.8911-1-kishon@ti.com >> [6] -> http://lore.kernel.org/r/20200915042110.3015-1-kishon@ti.com >> [7] -> http://lore.kernel.org/r/20200918064227.1463-1-kishon@ti.com >> [8] -> http://lore.kernel.org/r/20200924092519.17082-1-kishon@ti.com >> [9] -> https://youtu.be/dLKKxrg5-rY >> [10] -> http://lore.kernel.org/r/20200930153519.7282-1-kishon@ti.com >> [11] -> http://lore.kernel.org/r/20201111153559.19050-1-kishon@ti.com >> >> Kishon Vijay Abraham I (17): >> Documentation: PCI: Add specification for the *PCI NTB* function >> device >> PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit >> BAR >> PCI: endpoint: Add helper API to get the 'next' unreserved BAR >> PCI: endpoint: Make *_free_bar() to return error codes on failure >> PCI: endpoint: Remove unused pci_epf_match_device() >> PCI: endpoint: Add support to associate secondary EPC with EPF >> PCI: endpoint: Add support in configfs to associate two EPCs with EPF >> PCI: endpoint: Add pci_epc_ops to map MSI irq >> PCI: endpoint: Add pci_epf_ops for epf drivers to expose function >> specific attrs >> PCI: endpoint: Allow user to create sub-directory of 'EPF Device' >> directory >> PCI: cadence: Implement ->msi_map_irq() ops >> PCI: cadence: Configure LM_EP_FUNC_CFG based on epc->function_num_map >> PCI: endpoint: Add EP function driver to provide NTB functionality >> PCI: Add TI J721E device to pci ids >> NTB: Add support for EPF PCI-Express Non-Transparent Bridge >> Documentation: PCI: Add configfs binding documentation for pci-ntb >> endpoint function >> Documentation: PCI: Add userguide for PCI endpoint NTB function >> >> .../PCI/endpoint/function/binding/pci-ntb.rst | 38 + >> Documentation/PCI/endpoint/index.rst | 3 + >> .../PCI/endpoint/pci-endpoint-cfs.rst | 10 + >> .../PCI/endpoint/pci-ntb-function.rst | 351 +++ >> Documentation/PCI/endpoint/pci-ntb-howto.rst | 160 ++ >> drivers/misc/pci_endpoint_test.c | 1 - >> drivers/ntb/hw/Kconfig | 1 + >> drivers/ntb/hw/Makefile | 1 + >> drivers/ntb/hw/epf/Kconfig | 6 + >> drivers/ntb/hw/epf/Makefile | 1 + >> drivers/ntb/hw/epf/ntb_hw_epf.c | 754 ++++++ >> .../pci/controller/cadence/pcie-cadence-ep.c | 60 +- >> drivers/pci/endpoint/functions/Kconfig | 12 + >> drivers/pci/endpoint/functions/Makefile | 1 + >> drivers/pci/endpoint/functions/pci-epf-ntb.c | 2114 +++++++++++++++++ >> drivers/pci/endpoint/functions/pci-epf-test.c | 13 +- >> drivers/pci/endpoint/pci-ep-cfs.c | 176 +- >> drivers/pci/endpoint/pci-epc-core.c | 130 +- >> drivers/pci/endpoint/pci-epf-core.c | 105 +- >> include/linux/pci-epc.h | 39 +- >> include/linux/pci-epf.h | 28 +- >> include/linux/pci_ids.h | 1 + >> 22 files changed, 3932 insertions(+), 73 deletions(-) >> create mode 100644 Documentation/PCI/endpoint/function/binding/pci-ntb.rst >> create mode 100644 Documentation/PCI/endpoint/pci-ntb-function.rst >> create mode 100644 Documentation/PCI/endpoint/pci-ntb-howto.rst >> create mode 100644 drivers/ntb/hw/epf/Kconfig >> create mode 100644 drivers/ntb/hw/epf/Makefile >> create mode 100644 drivers/ntb/hw/epf/ntb_hw_epf.c >> create mode 100644 drivers/pci/endpoint/functions/pci-epf-ntb.c >>
On Mon, 4 Jan 2021 20:58:52 +0530, Kishon Vijay Abraham I wrote: > This series is about implementing SW defined Non-Transparent Bridge (NTB) > using multiple endpoint (EP) instances. This series has been tested using > 2 endpoint instances in J7 connected to J7 board on one end and DRA7 board > on the other end. However there is nothing platform specific for the NTB > functionality. > > This was presented in Linux Plumbers Conference. Link to presentation > and video can be found @ [1] > Created a video demo @ [9] > > [...] Applied to pci/ntb to give it more visibility and testing, aiming for v5.12. [01/17] Documentation: PCI: Add specification for the *PCI NTB* function device https://git.kernel.org/lpieralisi/pci/c/75e6ac86ca [02/17] PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit BAR https://git.kernel.org/lpieralisi/pci/c/b6c7a2a2b5 [03/17] PCI: endpoint: Add helper API to get the 'next' unreserved BAR https://git.kernel.org/lpieralisi/pci/c/43e293914d [04/17] PCI: endpoint: Make *_free_bar() to return error codes on failure https://git.kernel.org/lpieralisi/pci/c/293e2c258c [05/17] PCI: endpoint: Remove unused pci_epf_match_device() https://git.kernel.org/lpieralisi/pci/c/9a25bdab98 [06/17] PCI: endpoint: Add support to associate secondary EPC with EPF https://git.kernel.org/lpieralisi/pci/c/868fe90ea4 [07/17] PCI: endpoint: Add support in configfs to associate two EPCs with EPF https://git.kernel.org/lpieralisi/pci/c/632c92ec12 [08/17] PCI: endpoint: Add pci_epc_ops to map MSI irq https://git.kernel.org/lpieralisi/pci/c/310511a301 [09/17] PCI: endpoint: Add pci_epf_ops for epf drivers to expose function specific attrs https://git.kernel.org/lpieralisi/pci/c/34fb8ab2e3 [10/17] PCI: endpoint: Allow user to create sub-directory of 'EPF Device' directory https://git.kernel.org/lpieralisi/pci/c/3a5c112c7a [11/17] PCI: cadence: Implement ->msi_map_irq() ops https://git.kernel.org/lpieralisi/pci/c/d5c3d2ae7c [12/17] PCI: cadence: Configure LM_EP_FUNC_CFG based on epc->function_num_map https://git.kernel.org/lpieralisi/pci/c/d3f4973104 [13/17] PCI: endpoint: Add EP function driver to provide NTB functionality https://git.kernel.org/lpieralisi/pci/c/7dc64244f9 [14/17] PCI: Add TI J721E device to pci ids https://git.kernel.org/lpieralisi/pci/c/17d49876c3 [15/17] NTB: Add support for EPF PCI-Express Non-Transparent Bridge https://git.kernel.org/lpieralisi/pci/c/5d0db3f429 [16/17] Documentation: PCI: Add configfs binding documentation for pci-ntb endpoint function https://git.kernel.org/lpieralisi/pci/c/099f07051e [17/17] Documentation: PCI: Add userguide for PCI endpoint NTB function https://git.kernel.org/lpieralisi/pci/c/27f22f76c3 Thanks, Lorenzo
This series is about implementing SW defined Non-Transparent Bridge (NTB) using multiple endpoint (EP) instances. This series has been tested using 2 endpoint instances in J7 connected to J7 board on one end and DRA7 board on the other end. However there is nothing platform specific for the NTB functionality. This was presented in Linux Plumbers Conference. Link to presentation and video can be found @ [1] Created a video demo @ [9] RFC patch series can be found @ [2] v1 patch series can be found @ [3] v2 patch series can be found @ [4] v3 patch series can be found @ [5] v4 patch series can be found @ [6] v5 patch series can be found @ [7] v6 patch series can be found @ [8] v7 patch series can be found @ [10] v8 patch series can be found @ [11] Changes from v8: 1) Do not use devm_request_irq/devm_free_irq as pci_free_irq_vectors() has to be used after free_irq 2) Drop "NTB: tool: Enable the NTB/PCIe link on the local or remote side of bridge" as there is a debugfs entry to enable the link Changes from v7: 1) Used values stored in ctrl_reg_bar, peer_spad_reg_bar and db_reg_bar instead of hardcoded values in pci_iomap of ntb_hw_epf.c driver Changes from v6: 1) Fixed issues when multiple NTB devices are creating using multiple functions 2) Fixed issue with writing scratchpad register 3) Created a video demo @ [9] Changes from v5: 1) Fixed a formatting issue in Kconfig pointed out by Randy 2) Checked for Error or Null in pci_epc_add_epf() Changes from v4: 1) Fixed error condition checks in pci_epc_add_epf() Changes from v3: 1) Fixed Documentation edits suggested by Randy Dunlap <rdunlap@infradead.org> Changes from v2: 1) Add support for the user to create sub-directory of 'EPF Device' directory (for endpoint function specific configuration using configfs). 2) Add documentation for NTB specific attributes in configfs 3) Check for PCI_CLASS_MEMORY_RAM (PCIe class) before binding ntb_hw_epf driver 4) Other documentation fixes Changes from v1: 1) As per Rob's comment, removed support for creating NTB function device from DT 2) Add support to create NTB EPF device using configfs (added support in configfs to associate primary and secondary EPC with EPF. Changes from RFC: 1) Converted the DT binding patches to YAML schema and merged the DT binding patches together 2) NTB documentation is converted to .rst 3) One HOST can now interrupt the other HOST using MSI-X interrupts 4) Added support for teardown of memory window and doorbell configuration 5) Add support to provide support 64-bit memory window size from DT [1] -> https://linuxplumbersconf.org/event/4/contributions/395/ [2] -> http://lore.kernel.org/r/20190926112933.8922-1-kishon@ti.com [3] -> http://lore.kernel.org/r/20200514145927.17555-1-kishon@ti.com [4] -> http://lore.kernel.org/r/20200611130525.22746-1-kishon@ti.com [5] -> http://lore.kernel.org/r/20200904075052.8911-1-kishon@ti.com [6] -> http://lore.kernel.org/r/20200915042110.3015-1-kishon@ti.com [7] -> http://lore.kernel.org/r/20200918064227.1463-1-kishon@ti.com [8] -> http://lore.kernel.org/r/20200924092519.17082-1-kishon@ti.com [9] -> https://youtu.be/dLKKxrg5-rY [10] -> http://lore.kernel.org/r/20200930153519.7282-1-kishon@ti.com [11] -> http://lore.kernel.org/r/20201111153559.19050-1-kishon@ti.com Kishon Vijay Abraham I (17): Documentation: PCI: Add specification for the *PCI NTB* function device PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit BAR PCI: endpoint: Add helper API to get the 'next' unreserved BAR PCI: endpoint: Make *_free_bar() to return error codes on failure PCI: endpoint: Remove unused pci_epf_match_device() PCI: endpoint: Add support to associate secondary EPC with EPF PCI: endpoint: Add support in configfs to associate two EPCs with EPF PCI: endpoint: Add pci_epc_ops to map MSI irq PCI: endpoint: Add pci_epf_ops for epf drivers to expose function specific attrs PCI: endpoint: Allow user to create sub-directory of 'EPF Device' directory PCI: cadence: Implement ->msi_map_irq() ops PCI: cadence: Configure LM_EP_FUNC_CFG based on epc->function_num_map PCI: endpoint: Add EP function driver to provide NTB functionality PCI: Add TI J721E device to pci ids NTB: Add support for EPF PCI-Express Non-Transparent Bridge Documentation: PCI: Add configfs binding documentation for pci-ntb endpoint function Documentation: PCI: Add userguide for PCI endpoint NTB function .../PCI/endpoint/function/binding/pci-ntb.rst | 38 + Documentation/PCI/endpoint/index.rst | 3 + .../PCI/endpoint/pci-endpoint-cfs.rst | 10 + .../PCI/endpoint/pci-ntb-function.rst | 351 +++ Documentation/PCI/endpoint/pci-ntb-howto.rst | 160 ++ drivers/misc/pci_endpoint_test.c | 1 - drivers/ntb/hw/Kconfig | 1 + drivers/ntb/hw/Makefile | 1 + drivers/ntb/hw/epf/Kconfig | 6 + drivers/ntb/hw/epf/Makefile | 1 + drivers/ntb/hw/epf/ntb_hw_epf.c | 754 ++++++ .../pci/controller/cadence/pcie-cadence-ep.c | 60 +- drivers/pci/endpoint/functions/Kconfig | 12 + drivers/pci/endpoint/functions/Makefile | 1 + drivers/pci/endpoint/functions/pci-epf-ntb.c | 2114 +++++++++++++++++ drivers/pci/endpoint/functions/pci-epf-test.c | 13 +- drivers/pci/endpoint/pci-ep-cfs.c | 176 +- drivers/pci/endpoint/pci-epc-core.c | 130 +- drivers/pci/endpoint/pci-epf-core.c | 105 +- include/linux/pci-epc.h | 39 +- include/linux/pci-epf.h | 28 +- include/linux/pci_ids.h | 1 + 22 files changed, 3932 insertions(+), 73 deletions(-) create mode 100644 Documentation/PCI/endpoint/function/binding/pci-ntb.rst create mode 100644 Documentation/PCI/endpoint/pci-ntb-function.rst create mode 100644 Documentation/PCI/endpoint/pci-ntb-howto.rst create mode 100644 drivers/ntb/hw/epf/Kconfig create mode 100644 drivers/ntb/hw/epf/Makefile create mode 100644 drivers/ntb/hw/epf/ntb_hw_epf.c create mode 100644 drivers/pci/endpoint/functions/pci-epf-ntb.c