@@ -237,7 +237,7 @@ static int hisi_spi_nor_dma_transfer(struct spi_nor *nor, loff_t start_off,
reg = readl(host->regbase + FMC_CFG);
reg &= ~(FMC_CFG_OP_MODE_MASK | SPI_NOR_ADDR_MODE_MASK);
reg |= FMC_CFG_OP_MODE_NORMAL;
- reg |= (nor->addr_width == 4) ? SPI_NOR_ADDR_MODE_4BYTES
+ reg |= (nor->addr_nbytes == 4) ? SPI_NOR_ADDR_MODE_4BYTES
: SPI_NOR_ADDR_MODE_3BYTES;
writel(reg, host->regbase + FMC_CFG);
@@ -203,7 +203,7 @@ static ssize_t nxp_spifi_write(struct spi_nor *nor, loff_t to, size_t len,
SPIFI_CMD_DATALEN(len) |
SPIFI_CMD_FIELDFORM_ALL_SERIAL |
SPIFI_CMD_OPCODE(nor->program_opcode) |
- SPIFI_CMD_FRAMEFORM(spifi->nor.addr_width + 1);
+ SPIFI_CMD_FRAMEFORM(spifi->nor.addr_nbytes + 1);
writel(cmd, spifi->io_base + SPIFI_CMD);
for (i = 0; i < len; i++)
@@ -230,7 +230,7 @@ static int nxp_spifi_erase(struct spi_nor *nor, loff_t offs)
cmd = SPIFI_CMD_FIELDFORM_ALL_SERIAL |
SPIFI_CMD_OPCODE(nor->erase_opcode) |
- SPIFI_CMD_FRAMEFORM(spifi->nor.addr_width + 1);
+ SPIFI_CMD_FRAMEFORM(spifi->nor.addr_nbytes + 1);
writel(cmd, spifi->io_base + SPIFI_CMD);
return nxp_spifi_wait_for_cmd(spifi);
@@ -252,12 +252,12 @@ static int nxp_spifi_setup_memory_cmd(struct nxp_spifi *spifi)
}
/* Memory mode supports address length between 1 and 4 */
- if (spifi->nor.addr_width < 1 || spifi->nor.addr_width > 4)
+ if (spifi->nor.addr_nbytes < 1 || spifi->nor.addr_nbytes > 4)
return -EINVAL;
spifi->mcmd |= SPIFI_CMD_OPCODE(spifi->nor.read_opcode) |
SPIFI_CMD_INTLEN(spifi->nor.read_dummy / 8) |
- SPIFI_CMD_FRAMEFORM(spifi->nor.addr_width + 1);
+ SPIFI_CMD_FRAMEFORM(spifi->nor.addr_nbytes + 1);
return 0;
}
@@ -38,7 +38,7 @@
*/
#define CHIP_ERASE_2MB_READY_WAIT_JIFFIES (40UL * HZ)
-#define SPI_NOR_MAX_ADDR_WIDTH 4
+#define SPI_NOR_MAX_ADDR_NBYTES 4
#define SPI_NOR_SRST_SLEEP_MIN 200
#define SPI_NOR_SRST_SLEEP_MAX 400
@@ -198,7 +198,7 @@ static ssize_t spi_nor_spimem_read_data(struct spi_nor *nor, loff_t from,
{
struct spi_mem_op op =
SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, from, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, from, 0),
SPI_MEM_OP_DUMMY(nor->read_dummy, 0),
SPI_MEM_OP_DATA_IN(len, buf, 0));
bool usebouncebuf;
@@ -262,7 +262,7 @@ static ssize_t spi_nor_spimem_write_data(struct spi_nor *nor, loff_t to,
{
struct spi_mem_op op =
SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, to, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, to, 0),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(len, buf, 0));
ssize_t nbytes;
@@ -1113,7 +1113,7 @@ int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
if (nor->spimem) {
struct spi_mem_op op =
SPI_NOR_SECTOR_ERASE_OP(nor->erase_opcode,
- nor->addr_width, addr);
+ nor->addr_nbytes, addr);
spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
@@ -1126,13 +1126,13 @@ int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
* Default implementation, if driver doesn't have a specialized HW
* control
*/
- for (i = nor->addr_width - 1; i >= 0; i--) {
+ for (i = nor->addr_nbytes - 1; i >= 0; i--) {
nor->bouncebuf[i] = addr & 0xff;
addr >>= 8;
}
return spi_nor_controller_ops_write_reg(nor, nor->erase_opcode,
- nor->bouncebuf, nor->addr_width);
+ nor->bouncebuf, nor->addr_nbytes);
}
/**
@@ -2249,9 +2249,9 @@ static int spi_nor_default_setup(struct spi_nor *nor,
return 0;
}
-static int spi_nor_set_addr_width(struct spi_nor *nor)
+static int spi_nor_set_addr_nbytes(struct spi_nor *nor)
{
- if (nor->addr_width) {
+ if (nor->addr_nbytes) {
/* already configured from SFDP */
} else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) {
/*
@@ -2266,26 +2266,26 @@ static int spi_nor_set_addr_width(struct spi_nor *nor)
* Force all 8D-8D-8D flashes to use an address width of 4 to
* avoid this situation.
*/
- nor->addr_width = 4;
- } else if (nor->info->addr_width) {
- nor->addr_width = nor->info->addr_width;
+ nor->addr_nbytes = 4;
+ } else if (nor->info->addr_nbytes) {
+ nor->addr_nbytes = nor->info->addr_nbytes;
} else {
- nor->addr_width = 3;
+ nor->addr_nbytes = 3;
}
- if (nor->addr_width == 3 && nor->params->size > 0x1000000) {
+ if (nor->addr_nbytes == 3 && nor->params->size > 0x1000000) {
/* enable 4-byte addressing if the device exceeds 16MiB */
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
}
- if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
+ if (nor->addr_nbytes > SPI_NOR_MAX_ADDR_NBYTES) {
dev_dbg(nor->dev, "address width is too large: %u\n",
- nor->addr_width);
+ nor->addr_nbytes);
return -EINVAL;
}
/* Set 4byte opcodes when possible. */
- if (nor->addr_width == 4 && nor->flags & SNOR_F_4B_OPCODES &&
+ if (nor->addr_nbytes == 4 && nor->flags & SNOR_F_4B_OPCODES &&
!(nor->flags & SNOR_F_HAS_4BAIT))
spi_nor_set_4byte_opcodes(nor);
@@ -2304,7 +2304,7 @@ static int spi_nor_setup(struct spi_nor *nor,
if (ret)
return ret;
- return spi_nor_set_addr_width(nor);
+ return spi_nor_set_addr_nbytes(nor);
}
/**
@@ -2497,7 +2497,7 @@ static void spi_nor_sfdp_init_params_deprecated(struct spi_nor *nor)
if (spi_nor_parse_sfdp(nor)) {
memcpy(nor->params, &sfdp_params, sizeof(*nor->params));
- nor->addr_width = 0;
+ nor->addr_nbytes = 0;
nor->flags &= ~SNOR_F_4B_OPCODES;
}
}
@@ -2718,7 +2718,7 @@ static int spi_nor_init(struct spi_nor *nor)
nor->flags & SNOR_F_SWP_IS_VOLATILE))
spi_nor_try_unlock_all(nor);
- if (nor->addr_width == 4 &&
+ if (nor->addr_nbytes == 4 &&
nor->read_proto != SNOR_PROTO_8_8_8_DTR &&
!(nor->flags & SNOR_F_4B_OPCODES)) {
/*
@@ -2845,7 +2845,7 @@ static void spi_nor_put_device(struct mtd_info *mtd)
void spi_nor_restore(struct spi_nor *nor)
{
/* restore the addressing mode */
- if (nor->addr_width == 4 && !(nor->flags & SNOR_F_4B_OPCODES) &&
+ if (nor->addr_nbytes == 4 && !(nor->flags & SNOR_F_4B_OPCODES) &&
nor->flags & SNOR_F_BROKEN_RESET)
nor->params->set_4byte_addr_mode(nor, false);
@@ -3030,7 +3030,7 @@ static int spi_nor_create_read_dirmap(struct spi_nor *nor)
{
struct spi_mem_dirmap_info info = {
.op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, 0, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, 0, 0),
SPI_MEM_OP_DUMMY(nor->read_dummy, 0),
SPI_MEM_OP_DATA_IN(0, NULL, 0)),
.offset = 0,
@@ -3061,7 +3061,7 @@ static int spi_nor_create_write_dirmap(struct spi_nor *nor)
{
struct spi_mem_dirmap_info info = {
.op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, 0, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, 0, 0),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(0, NULL, 0)),
.offset = 0,
@@ -84,9 +84,9 @@
SPI_MEM_OP_NO_DUMMY, \
SPI_MEM_OP_NO_DATA)
-#define SPI_NOR_SECTOR_ERASE_OP(opcode, addr_width, addr) \
+#define SPI_NOR_SECTOR_ERASE_OP(opcode, addr_nbytes, addr) \
SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 0), \
- SPI_MEM_OP_ADDR(addr_width, addr, 0), \
+ SPI_MEM_OP_ADDR(addr_nbytes, addr, 0), \
SPI_MEM_OP_NO_DUMMY, \
SPI_MEM_OP_NO_DATA)
@@ -429,7 +429,7 @@ struct spi_nor_fixups {
* isn't necessarily called a "sector" by the vendor.
* @n_sectors: the number of sectors.
* @page_size: the flash's page size.
- * @addr_width: the flash's address width.
+ * @addr_nbytes: number of address bytes to send.
*
* @parse_sfdp: true when flash supports SFDP tables. The false value has no
* meaning. If one wants to skip the SFDP tables, one should
@@ -488,7 +488,7 @@ struct flash_info {
unsigned sector_size;
u16 n_sectors;
u16 page_size;
- u16 addr_width;
+ u16 addr_nbytes;
bool parse_sfdp;
u16 flags;
@@ -550,11 +550,11 @@ struct flash_info {
.n_sectors = (_n_sectors), \
.page_size = 256, \
-#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width) \
+#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_nbytes) \
.sector_size = (_sector_size), \
.n_sectors = (_n_sectors), \
.page_size = (_page_size), \
- .addr_width = (_addr_width), \
+ .addr_nbytes = (_addr_nbytes), \
.flags = SPI_NOR_NO_ERASE | SPI_NOR_NO_FR, \
#define OTP_INFO(_len, _n_regions, _base, _offset) \
@@ -20,7 +20,7 @@ is25lp256_post_bfpt_fixups(struct spi_nor *nor,
*/
if ((bfpt->dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) ==
BFPT_DWORD1_ADDRESS_BYTES_3_ONLY)
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
return 0;
}
@@ -35,13 +35,13 @@
*/
int spi_nor_otp_read_secr(struct spi_nor *nor, loff_t addr, size_t len, u8 *buf)
{
- u8 addr_width, read_opcode, read_dummy;
+ u8 addr_nbytes, read_opcode, read_dummy;
struct spi_mem_dirmap_desc *rdesc;
enum spi_nor_protocol read_proto;
int ret;
read_opcode = nor->read_opcode;
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
read_dummy = nor->read_dummy;
read_proto = nor->read_proto;
rdesc = nor->dirmap.rdesc;
@@ -54,7 +54,7 @@ int spi_nor_otp_read_secr(struct spi_nor *nor, loff_t addr, size_t len, u8 *buf)
ret = spi_nor_read_data(nor, addr, len, buf);
nor->read_opcode = read_opcode;
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->read_dummy = read_dummy;
nor->read_proto = read_proto;
nor->dirmap.rdesc = rdesc;
@@ -85,11 +85,11 @@ int spi_nor_otp_write_secr(struct spi_nor *nor, loff_t addr, size_t len,
{
enum spi_nor_protocol write_proto;
struct spi_mem_dirmap_desc *wdesc;
- u8 addr_width, program_opcode;
+ u8 addr_nbytes, program_opcode;
int ret, written;
program_opcode = nor->program_opcode;
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
write_proto = nor->write_proto;
wdesc = nor->dirmap.wdesc;
@@ -113,7 +113,7 @@ int spi_nor_otp_write_secr(struct spi_nor *nor, loff_t addr, size_t len,
out:
nor->program_opcode = program_opcode;
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->write_proto = write_proto;
nor->dirmap.wdesc = wdesc;
@@ -134,7 +134,7 @@ struct sfdp_4bait {
/**
* spi_nor_read_raw() - raw read of serial flash memory. read_opcode,
- * addr_width and read_dummy members of the struct spi_nor
+ * addr_nbytes and read_dummy members of the struct spi_nor
* should be previously
* set.
* @nor: pointer to a 'struct spi_nor'
@@ -178,21 +178,21 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)
static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr,
size_t len, void *buf)
{
- u8 addr_width, read_opcode, read_dummy;
+ u8 addr_nbytes, read_opcode, read_dummy;
int ret;
read_opcode = nor->read_opcode;
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
read_dummy = nor->read_dummy;
nor->read_opcode = SPINOR_OP_RDSFDP;
- nor->addr_width = 3;
+ nor->addr_nbytes = 3;
nor->read_dummy = 8;
ret = spi_nor_read_raw(nor, addr, len, buf);
nor->read_opcode = read_opcode;
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->read_dummy = read_dummy;
return ret;
@@ -462,11 +462,11 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
switch (bfpt.dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) {
case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY:
case BFPT_DWORD1_ADDRESS_BYTES_3_OR_4:
- nor->addr_width = 3;
+ nor->addr_nbytes = 3;
break;
case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY:
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
break;
default:
@@ -637,12 +637,12 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
}
/**
- * spi_nor_smpt_addr_width() - return the address width used in the
+ * spi_nor_smpt_addr_nbytes() - return the number of address bytes used in the
* configuration detection command.
* @nor: pointer to a 'struct spi_nor'
* @settings: configuration detection command descriptor, dword1
*/
-static u8 spi_nor_smpt_addr_width(const struct spi_nor *nor, const u32 settings)
+static u8 spi_nor_smpt_addr_nbytes(const struct spi_nor *nor, const u32 settings)
{
switch (settings & SMPT_CMD_ADDRESS_LEN_MASK) {
case SMPT_CMD_ADDRESS_LEN_0:
@@ -653,7 +653,7 @@ static u8 spi_nor_smpt_addr_width(const struct spi_nor *nor, const u32 settings)
return 4;
case SMPT_CMD_ADDRESS_LEN_USE_CURRENT:
default:
- return nor->addr_width;
+ return nor->addr_nbytes;
}
}
@@ -690,7 +690,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
u32 addr;
int err;
u8 i;
- u8 addr_width, read_opcode, read_dummy;
+ u8 addr_nbytes, read_opcode, read_dummy;
u8 read_data_mask, map_id;
/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */
@@ -698,7 +698,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
if (!buf)
return ERR_PTR(-ENOMEM);
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
read_dummy = nor->read_dummy;
read_opcode = nor->read_opcode;
@@ -709,7 +709,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
break;
read_data_mask = SMPT_CMD_READ_DATA(smpt[i]);
- nor->addr_width = spi_nor_smpt_addr_width(nor, smpt[i]);
+ nor->addr_nbytes = spi_nor_smpt_addr_nbytes(nor, smpt[i]);
nor->read_dummy = spi_nor_smpt_read_dummy(nor, smpt[i]);
nor->read_opcode = SMPT_CMD_OPCODE(smpt[i]);
addr = smpt[i + 1];
@@ -756,7 +756,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
/* fall through */
out:
kfree(buf);
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->read_dummy = read_dummy;
nor->read_opcode = read_opcode;
return ret;
@@ -1044,7 +1044,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
/*
* We need at least one 4-byte op code per read, program and erase
* operation; the .read(), .write() and .erase() hooks share the
- * nor->addr_width value.
+ * nor->addr_nbytes value.
*/
if (!read_hwcaps || !pp_hwcaps || !erase_mask)
goto out;
@@ -1098,7 +1098,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
* Spansion memory. However this quirk is no longer needed with new
* SFDP compliant memories.
*/
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
nor->flags |= SNOR_F_4B_OPCODES | SNOR_F_HAS_4BAIT;
/* fall through */
@@ -31,7 +31,7 @@
.sector_size = (8 * (_page_size)), \
.n_sectors = (_n_sectors), \
.page_size = (_page_size), \
- .addr_width = 3, \
+ .addr_nbytes = 3, \
.flags = SPI_NOR_NO_FR
/* Xilinx S3AN share MFR with Atmel SPI NOR */
@@ -351,7 +351,7 @@ struct spi_nor_flash_parameter;
* @bouncebuf_size: size of the bounce buffer
* @info: SPI NOR part JEDEC MFR ID and other info
* @manufacturer: SPI NOR manufacturer
- * @addr_width: number of address bytes
+ * @addr_nbytes: number of address bytes
* @erase_opcode: the opcode for erasing a sector
* @read_opcode: the read opcode
* @read_dummy: the dummy needed by the read operation
@@ -381,7 +381,7 @@ struct spi_nor {
size_t bouncebuf_size;
const struct flash_info *info;
const struct spi_nor_manufacturer *manufacturer;
- u8 addr_width;
+ u8 addr_nbytes;
u8 erase_opcode;
u8 read_opcode;
u8 read_dummy;