diff -puN /dev/null arch/arm/mach-davinci/include/mach/nand.h
--- /dev/null
+++ a/arch/arm/mach-davinci/include/mach/nand.h
@@ -0,0 +1,80 @@
+/*
+ * mach-davinci/nand.h
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ *
+ * Ported to 2.6.23 Copyright (C) 2008 by
+ *   Sander Huijsen <Shuijsen@optelecom-nkf.com>
+ *   Troy Kisky <troy.kisky@boundarydevices.com>
+ *   Dirk Behme <Dirk.Behme@gmail.com>
+ *
+ * --------------------------------------------------------------------------
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ARCH_ARM_DAVINCI_NAND_H
+#define __ARCH_ARM_DAVINCI_NAND_H
+
+#include <linux/mtd/nand.h>
+
+#define NRCSR_OFFSET		0x00
+#define AWCCR_OFFSET		0x04
+#define A1CR_OFFSET		0x10
+#define NANDFCR_OFFSET		0x60
+#define NANDFSR_OFFSET		0x64
+#define NANDF1ECC_OFFSET	0x70
+
+/* 4-bit ECC syndrome registers */
+#define NAND_4BIT_ECC_LOAD_OFFSET	0xbc
+#define NAND_4BIT_ECC1_OFFSET		0xc0
+#define NAND_4BIT_ECC2_OFFSET		0xc4
+#define NAND_4BIT_ECC3_OFFSET		0xc8
+#define NAND_4BIT_ECC4_OFFSET		0xcc
+#define NAND_ERR_ADD1_OFFSET		0xd0
+#define NAND_ERR_ADD2_OFFSET		0xd4
+#define NAND_ERR_ERRVAL1_OFFSET		0xd8
+#define NAND_ERR_ERRVAL2_OFFSET		0xdc
+
+/* NOTE:  boards don't need to use these address bits
+ * for ALE/CLE unless they support booting from NAND.
+ * They're used unless platform data overrides them.
+ */
+#define	MASK_ALE		0x08
+#define	MASK_CLE		0x10
+
+struct davinci_nand_pdata {		/* platform_data */
+	u32			mask_ale;
+	u32			mask_cle;
+
+	/* for packages using two chipselects */
+	u32			mask_chipsel;
+
+	/* board's default static partition info */
+	struct mtd_partition	*parts;
+	unsigned		nr_parts;
+
+	/* none  == NAND_ECC_NONE (strongly *not* advised!!)
+	 * soft  == NAND_ECC_SOFT
+	 * 1-bit == NAND_ECC_HW
+	 * 4-bit == NAND_ECC_HW_SYNDROME (not on all chips)
+	 */
+	nand_ecc_modes_t	ecc_mode;
+
+	/* e.g. NAND_BUSWIDTH_16 or NAND_USE_FLASH_BBT */
+	unsigned		options;
+};
+
+#endif	/* __ARCH_ARM_DAVINCI_NAND_H */
diff -puN drivers/mtd/nand/Kconfig~nand-davinci_nand-driver drivers/mtd/nand/Kconfig
--- a/drivers/mtd/nand/Kconfig~nand-davinci_nand-driver
+++ a/drivers/mtd/nand/Kconfig
@@ -433,4 +433,11 @@ config MTD_NAND_TXX9NDFMC
 	help
 	  This enables the NAND flash controller on the TXx9 SoCs.
 
+config MTD_NAND_DAVINCI
+        tristate "Support NAND on DaVinci SoC"
+        depends on ARCH_DAVINCI
+        help
+	  Enable the driver for NAND flash chips on Texas Instruments
+	  DaVinci processors.
+
 endif # MTD_NAND
diff -puN drivers/mtd/nand/Makefile~nand-davinci_nand-driver drivers/mtd/nand/Makefile
--- a/drivers/mtd/nand/Makefile~nand-davinci_nand-driver
+++ a/drivers/mtd/nand/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_NAND_AU1550)		+= au1550
 obj-$(CONFIG_MTD_NAND_BF5XX)		+= bf5xx_nand.o
 obj-$(CONFIG_MTD_NAND_PPCHAMELEONEVB)	+= ppchameleonevb.o
 obj-$(CONFIG_MTD_NAND_S3C2410)		+= s3c2410.o
+obj-$(CONFIG_MTD_NAND_DAVINCI)		+= davinci_nand.o
 obj-$(CONFIG_MTD_NAND_DISKONCHIP)	+= diskonchip.o
 obj-$(CONFIG_MTD_NAND_H1900)		+= h1910.o
 obj-$(CONFIG_MTD_NAND_RTC_FROM4)	+= rtc_from4.o
diff -puN /dev/null drivers/mtd/nand/davinci_nand.c
--- /dev/null
+++ a/drivers/mtd/nand/davinci_nand.c
@@ -0,0 +1,584 @@
+/*
+ * davinci_nand.c - NAND Flash Driver for DaVinci family chips
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ *
+ * Port to 2.6.23 Copyright (C) 2008 by:
+ *   Sander Huijsen <Shuijsen@optelecom-nkf.com>
+ *   Troy Kisky <troy.kisky@boundarydevices.com>
+ *   Dirk Behme <Dirk.Behme@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+
+#include <mach/cpu.h>
+#include <mach/nand.h>
+
+#include <asm/mach-types.h>
+
+
+#ifdef CONFIG_MTD_PARTITIONS
+static inline int mtd_has_partitions(void) { return 1; }
+#else
+static inline int mtd_has_partitions(void) { return 0; }
+#endif
+
+#ifdef CONFIG_MTD_CMDLINE_PARTS
+static inline int mtd_has_cmdlinepart(void) { return 1; }
+#else
+static inline int mtd_has_cmdlinepart(void) { return 0; }
+#endif
+
+
+/*
+ * This is a device driver for the NAND flash controller found on the
+ * various DaVinci family chips.  It handles up to four SoC chipselects,
+ * and some flavors of secondary chipselect (e.g. based on A12) as used
+ * with multichip packages.
+ *
+ * The 1-bit ECC hardware is supported, but not yet the newer 4-bit ECC
+ * available on chips like the DM355 and OMAP-L137 and needed with the
+ * more error-prone MLC NAND chips.
+ *
+ * This driver assumes EM_WAIT connects all the NAND devices' RDY/nBUSY
+ * outputs in a "wire-AND" configuration, with no per-chip signals.
+ */
+struct davinci_nand_info {
+	struct mtd_info		mtd;
+	struct nand_chip	chip;
+
+	struct device		*dev;
+	struct clk		*clk;
+	bool			partitioned;
+
+	void __iomem		*base;
+	void __iomem		*vaddr;
+
+	u32			ioaddr;
+	u32			current_cs;
+
+	u32			mask_chipsel;
+	u32			mask_ale;
+	u32			mask_cle;
+
+	u32			core_chipsel;
+};
+
+static DEFINE_SPINLOCK(davinci_nand_lock);
+
+#define to_davinci_nand(m) container_of(m, struct davinci_nand_info, mtd)
+
+
+static inline unsigned int davinci_nand_readl(struct davinci_nand_info *info,
+		int offset)
+{
+	return __raw_readl(info->base + offset);
+}
+
+static inline void davinci_nand_writel(struct davinci_nand_info *info,
+		int offset, unsigned long value)
+{
+	__raw_writel(value, info->base + offset);
+}
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Access to hardware control lines:  ALE, CLE, secondary chipselect.
+ */
+
+static void nand_davinci_hwcontrol(struct mtd_info *mtd, int cmd,
+				   unsigned int ctrl)
+{
+	struct davinci_nand_info	*info = to_davinci_nand(mtd);
+	u32				addr = info->current_cs;
+	struct nand_chip		*nand = mtd->priv;
+
+	/* Did the control lines change? */
+	if (ctrl & NAND_CTRL_CHANGE) {
+		if ((ctrl & NAND_CTRL_CLE) == NAND_CTRL_CLE)
+			addr |= info->mask_cle;
+		else if ((ctrl & NAND_CTRL_ALE) == NAND_CTRL_ALE)
+			addr |= info->mask_ale;
+
+		nand->IO_ADDR_W = (void __iomem __force *)addr;
+	}
+
+	if (cmd != NAND_CMD_NONE)
+		iowrite8(cmd, nand->IO_ADDR_W);
+}
+
+static void nand_davinci_select_chip(struct mtd_info *mtd, int chip)
+{
+	struct davinci_nand_info	*info = to_davinci_nand(mtd);
+	u32				addr = info->ioaddr;
+
+	/* maybe kick in a second chipselect */
+	if (chip > 0)
+		addr |= info->mask_chipsel;
+	info->current_cs = addr;
+
+	info->chip.IO_ADDR_W = (void __iomem __force *)addr;
+	info->chip.IO_ADDR_R = info->chip.IO_ADDR_W;
+}
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * 1-bit hardware ECC ... context maintained for each core chipselect
+ */
+
+static inline u32 nand_davinci_readecc_1bit(struct mtd_info *mtd)
+{
+	struct davinci_nand_info *info = to_davinci_nand(mtd);
+
+	return davinci_nand_readl(info, NANDF1ECC_OFFSET
+			+ 4 * info->core_chipsel);
+}
+
+static void nand_davinci_hwctl_1bit(struct mtd_info *mtd, int mode)
+{
+	struct davinci_nand_info *info;
+	u32 nandcfr;
+	unsigned long flags;
+
+	info = to_davinci_nand(mtd);
+
+	/* Reset ECC hardware */
+	nand_davinci_readecc_1bit(mtd);
+
+	spin_lock_irqsave(&davinci_nand_lock, flags);
+
+	/* Restart ECC hardware */
+	nandcfr = davinci_nand_readl(info, NANDFCR_OFFSET);
+	nandcfr |= BIT(8 + info->core_chipsel);
+	davinci_nand_writel(info, NANDFCR_OFFSET, nandcfr);
+
+	spin_unlock_irqrestore(&davinci_nand_lock, flags);
+}
+
+/*
+ * Read hardware ECC value and pack into three bytes
+ */
+static int nand_davinci_calculate_1bit(struct mtd_info *mtd,
+				      const u_char *dat, u_char *ecc_code)
+{
+	unsigned int ecc_val = nand_davinci_readecc_1bit(mtd);
+	unsigned int ecc24 = (ecc_val & 0x0fff) | ((ecc_val & 0x0fff0000) >> 4);
+
+	/* invert so that erased block ecc is correct */
+	ecc24 = ~ecc24;
+	ecc_code[0] = (u_char)(ecc24);
+	ecc_code[1] = (u_char)(ecc24 >> 8);
+	ecc_code[2] = (u_char)(ecc24 >> 16);
+
+	return 0;
+}
+
+static int nand_davinci_correct_1bit(struct mtd_info *mtd, u_char *dat,
+				     u_char *read_ecc, u_char *calc_ecc)
+{
+	struct nand_chip *chip = mtd->priv;
+	u_int32_t eccNand = read_ecc[0] | (read_ecc[1] << 8) |
+					  (read_ecc[2] << 16);
+	u_int32_t eccCalc = calc_ecc[0] | (calc_ecc[1] << 8) |
+					  (calc_ecc[2] << 16);
+	u_int32_t diff = eccCalc ^ eccNand;
+
+	if (diff) {
+		if ((((diff >> 12) ^ diff) & 0xfff) == 0xfff) {
+			/* Correctable error */
+			if ((diff >> (12 + 3)) < chip->ecc.size) {
+				dat[diff >> (12 + 3)] ^= BIT((diff >> 12) & 7);
+				return 1;
+			} else {
+				return -1;
+			}
+		} else if (!(diff & (diff - 1))) {
+			/* Single bit ECC error in the ECC itself,
+			 * nothing to fix */
+			return 1;
+		} else {
+			/* Uncorrectable error */
+			return -1;
+		}
+
+	}
+	return 0;
+}
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * NOTE:  NAND boot requires ALE == EM_A[1], CLE == EM_A[2], so that's
+ * how these chips are normally wired.  This translates to both 8 and 16
+ * bit busses using ALE == BIT(3) in byte addresses, and CLE == BIT(4).
+ *
+ * For now we assume that configuration, or any other one which ignores
+ * the two LSBs for NAND access ... so we can issue 32-bit reads/writes
+ * and have that transparently morphed into multiple NAND operations.
+ */
+static void nand_davinci_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+
+	if ((0x03 & ((unsigned)buf)) == 0 && (0x03 & len) == 0)
+		ioread32_rep(chip->IO_ADDR_R, buf, len >> 2);
+	else if ((0x01 & ((unsigned)buf)) == 0 && (0x01 & len) == 0)
+		ioread16_rep(chip->IO_ADDR_R, buf, len >> 1);
+	else
+		ioread8_rep(chip->IO_ADDR_R, buf, len);
+}
+
+static void nand_davinci_write_buf(struct mtd_info *mtd,
+		const uint8_t *buf, int len)
+{
+	struct nand_chip *chip = mtd->priv;
+
+	if ((0x03 & ((unsigned)buf)) == 0 && (0x03 & len) == 0)
+		iowrite32_rep(chip->IO_ADDR_R, buf, len >> 2);
+	else if ((0x01 & ((unsigned)buf)) == 0 && (0x01 & len) == 0)
+		iowrite16_rep(chip->IO_ADDR_R, buf, len >> 1);
+	else
+		iowrite8_rep(chip->IO_ADDR_R, buf, len);
+}
+
+/*
+ * Check hardware register for wait status. Returns 1 if device is ready,
+ * 0 if it is still busy.
+ */
+static int nand_davinci_dev_ready(struct mtd_info *mtd)
+{
+	struct davinci_nand_info *info = to_davinci_nand(mtd);
+
+	return davinci_nand_readl(info, NANDFSR_OFFSET) & BIT(0);
+}
+
+static void __init nand_dm6446evm_flash_init(struct davinci_nand_info *info)
+{
+	u32 regval, a1cr;
+
+	/*
+	 * NAND FLASH timings @ PLL1 == 459 MHz
+	 *  - AEMIF.CLK freq   = PLL1/6 = 459/6 = 76.5 MHz
+	 *  - AEMIF.CLK period = 1/76.5 MHz = 13.1 ns
+	 */
+	regval = 0
+		| (0 << 31)           /* selectStrobe */
+		| (0 << 30)           /* extWait (never with NAND) */
+		| (1 << 26)           /* writeSetup      10 ns */
+		| (3 << 20)           /* writeStrobe     40 ns */
+		| (1 << 17)           /* writeHold       10 ns */
+		| (0 << 13)           /* readSetup       10 ns */
+		| (3 << 7)            /* readStrobe      60 ns */
+		| (0 << 4)            /* readHold        10 ns */
+		| (3 << 2)            /* turnAround      ?? ns */
+		| (0 << 0)            /* asyncSize       8-bit bus */
+		;
+	a1cr = davinci_nand_readl(info, A1CR_OFFSET);
+	if (a1cr != regval) {
+		dev_dbg(info->dev, "Warning: NAND config: Set A1CR " \
+		       "reg to 0x%08x, was 0x%08x, should be done by " \
+		       "bootloader.\n", regval, a1cr);
+		davinci_nand_writel(info, A1CR_OFFSET, regval);
+	}
+}
+
+/*----------------------------------------------------------------------*/
+
+static int __init nand_davinci_probe(struct platform_device *pdev)
+{
+	struct davinci_nand_pdata	*pdata = pdev->dev.platform_data;
+	struct davinci_nand_info	*info;
+	struct resource			*res1;
+	struct resource			*res2;
+	void __iomem			*vaddr;
+	void __iomem			*base;
+	int				ret;
+	u32				val;
+	nand_ecc_modes_t		ecc_mode;
+
+	/* which external chipselect will we be managing? */
+	if (pdev->id < 0 || pdev->id > 3)
+		return -ENODEV;
+
+	info = kzalloc(sizeof(*info), GFP_KERNEL);
+	if (!info) {
+		dev_err(&pdev->dev, "unable to allocate memory\n");
+		ret = -ENOMEM;
+		goto err_nomem;
+	}
+
+	platform_set_drvdata(pdev, info);
+
+	res1 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	res2 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (!res1 || !res2) {
+		dev_err(&pdev->dev, "resource missing\n");
+		ret = -EINVAL;
+		goto err_nomem;
+	}
+
+	vaddr = ioremap(res1->start, res1->end - res1->start);
+	base = ioremap(res2->start, res2->end - res2->start);
+	if (!vaddr || !base) {
+		dev_err(&pdev->dev, "ioremap failed\n");
+		ret = -EINVAL;
+		goto err_ioremap;
+	}
+
+	info->dev		= &pdev->dev;
+	info->base		= base;
+	info->vaddr		= vaddr;
+
+	info->mtd.priv		= &info->chip;
+	info->mtd.name		= dev_name(&pdev->dev);
+	info->mtd.owner		= THIS_MODULE;
+
+	info->chip.IO_ADDR_R	= vaddr;
+	info->chip.IO_ADDR_W	= vaddr;
+	info->chip.chip_delay	= 0;
+	info->chip.select_chip	= nand_davinci_select_chip;
+
+	/* options such as NAND_USE_FLASH_BBT or 16-bit widths */
+	info->chip.options	= pdata ? pdata->options : 0;
+
+	info->ioaddr		= (u32 __force) vaddr;
+
+	info->current_cs	= info->ioaddr;
+	info->core_chipsel	= pdev->id;
+	info->mask_chipsel	= pdata->mask_chipsel;
+
+	/* use nandboot-capable ALE/CLE masks by default */
+	if (pdata && pdata->mask_ale)
+		info->mask_ale	= pdata->mask_cle;
+	else
+		info->mask_ale	= MASK_ALE;
+	if (pdata && pdata->mask_cle)
+		info->mask_cle	= pdata->mask_cle;
+	else
+		info->mask_cle	= MASK_CLE;
+
+	/* Set address of hardware control function */
+	info->chip.cmd_ctrl	= nand_davinci_hwcontrol;
+	info->chip.dev_ready	= nand_davinci_dev_ready;
+
+	/* Speed up buffer I/O */
+	info->chip.read_buf     = nand_davinci_read_buf;
+	info->chip.write_buf    = nand_davinci_write_buf;
+
+	/* use board-specific ECC config; else, the best available */
+	if (pdata)
+		ecc_mode = pdata->ecc_mode;
+	else if (cpu_is_davinci_dm355())
+		ecc_mode = NAND_ECC_HW_SYNDROME;
+	else
+		ecc_mode = NAND_ECC_HW;
+
+	switch (ecc_mode) {
+	case NAND_ECC_NONE:
+	case NAND_ECC_SOFT:
+		break;
+	case NAND_ECC_HW:
+		info->chip.ecc.calculate = nand_davinci_calculate_1bit;
+		info->chip.ecc.correct = nand_davinci_correct_1bit;
+		info->chip.ecc.hwctl = nand_davinci_hwctl_1bit;
+		info->chip.ecc.size = 512;
+		info->chip.ecc.bytes = 3;
+		break;
+	case NAND_ECC_HW_SYNDROME:
+		/* FIXME implement */
+		info->chip.ecc.size = 512;
+		info->chip.ecc.bytes = 10;
+
+		dev_warn(&pdev->dev, "4-bit ECC nyet supported\n");
+		/* FALL THROUGH */
+	default:
+		ret = -EINVAL;
+		goto err_ecc;
+	}
+	info->chip.ecc.mode = ecc_mode;
+
+	info->clk = clk_get(&pdev->dev, "AEMIFCLK");
+	if (IS_ERR(info->clk)) {
+		ret = PTR_ERR(info->clk);
+		dev_dbg(&pdev->dev, "unable to get AEMIFCLK, err %d\n", ret);
+		goto err_clk;
+	}
+
+	ret = clk_enable(info->clk);
+	if (ret < 0) {
+		dev_dbg(&pdev->dev, "unable to enable AEMIFCLK, err %d\n", ret);
+		goto err_clk_enable;
+	}
+
+	/* EMIF timings should normally be set by the boot loader,
+	 * especially after boot-from-NAND.  The *only* reason to
+	 * have this special casing for the DM6446 EVM is to work
+	 * with boot-from-NOR ... with CS0 manually re-jumpered
+	 * (after startup) so it addresses the NAND flash, not NOR.
+	 * Even for dev boards, that's unusually rude...
+	 */
+	if (machine_is_davinci_evm())
+		nand_dm6446evm_flash_init(info);
+
+	spin_lock_irq(&davinci_nand_lock);
+
+	/* put CSxNAND into NAND mode */
+	val = davinci_nand_readl(info, NANDFCR_OFFSET);
+	val |= BIT(info->core_chipsel);
+	davinci_nand_writel(info, NANDFCR_OFFSET, val);
+
+	spin_unlock_irq(&davinci_nand_lock);
+
+	/* Scan to find existence of the device(s) */
+	ret = nand_scan(&info->mtd, pdata->mask_chipsel ? 2 : 1);
+	if (ret < 0) {
+		dev_dbg(&pdev->dev, "no NAND chip(s) found\n");
+		goto err_scan;
+	}
+
+	if (mtd_has_partitions()) {
+		struct mtd_partition	*mtd_parts = NULL;
+		int			mtd_parts_nb = 0;
+
+		if (mtd_has_cmdlinepart()) {
+			static const char *probes[] __initconst =
+				{ "cmdlinepart", NULL };
+
+			const char		*master_name;
+
+			/* Set info->mtd.name = 0 temporarily */
+			master_name		= info->mtd.name;
+			info->mtd.name		= (char *)0;
+
+			/* info->mtd.name == 0, means: don't bother checking
+			   <mtd-id> */
+			mtd_parts_nb = parse_mtd_partitions(&info->mtd, probes,
+							    &mtd_parts, 0);
+
+			/* Restore info->mtd.name */
+			info->mtd.name = master_name;
+		}
+
+		if (mtd_parts_nb <= 0 && pdata) {
+			mtd_parts = pdata->parts;
+			mtd_parts_nb = pdata->nr_parts;
+		}
+
+		/* Register any partitions */
+		if (mtd_parts_nb > 0) {
+			ret = add_mtd_partitions(&info->mtd,
+					mtd_parts, mtd_parts_nb);
+			if (ret == 0)
+				info->partitioned = true;
+		}
+
+	} else if (pdata && pdata->nr_parts) {
+		dev_warn(&pdev->dev, "ignoring %d default partitions on %s\n",
+				pdata->nr_parts, info->mtd.name);
+	}
+
+	/* If there's no partition info, just package the whole chip
+	 * as a single MTD device.
+	 */
+	if (!info->partitioned)
+		ret = add_mtd_device(&info->mtd) ? -ENODEV : 0;
+
+	if (ret < 0)
+		goto err_scan;
+
+	val = davinci_nand_readl(info, NRCSR_OFFSET);
+	dev_info(&pdev->dev, "controller rev. %d.%d\n",
+	       (val >> 8) & 0xff, val & 0xff);
+
+	return 0;
+
+err_scan:
+	clk_disable(info->clk);
+
+err_clk_enable:
+	clk_put(info->clk);
+
+err_ecc:
+err_clk:
+err_ioremap:
+	if (base)
+		iounmap(base);
+	if (vaddr)
+		iounmap(vaddr);
+
+err_nomem:
+	kfree(info);
+	return ret;
+}
+
+static int __exit nand_davinci_remove(struct platform_device *pdev)
+{
+	struct davinci_nand_info *info = platform_get_drvdata(pdev);
+	int status;
+
+	if (mtd_has_partitions() && info->partitioned)
+		status = del_mtd_partitions(&info->mtd);
+	else
+		status = del_mtd_device(&info->mtd);
+
+	iounmap(info->base);
+	iounmap(info->vaddr);
+
+	nand_release(&info->mtd);
+
+	clk_disable(info->clk);
+	clk_put(info->clk);
+
+	kfree(info);
+
+	return 0;
+}
+
+static struct platform_driver nand_davinci_driver = {
+	.remove		= __exit_p(nand_davinci_remove),
+	.driver		= {
+		.name	= "davinci_nand",
+	},
+};
+MODULE_ALIAS("platform:davinci_nand");
+
+static int __init nand_davinci_init(void)
+{
+	return platform_driver_probe(&nand_davinci_driver, nand_davinci_probe);
+}
+module_init(nand_davinci_init);
+
+static void __exit nand_davinci_exit(void)
+{
+	platform_driver_unregister(&nand_davinci_driver);
+}
+module_exit(nand_davinci_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Texas Instruments");
+MODULE_DESCRIPTION("Davinci NAND flash driver");
+
