@@ -23,9 +23,20 @@ config MTD_PHYSMAP
To compile this driver as a module, choose M here: the
module will be called physmap.
+config MTD_PHYSMAP_COMPAT
+ bool "Physmap compat support"
+ depends on MTD_PHYSMAP
+ default n
+ help
+ Setup a simple mapping via the Kconfig options. Normally the
+ physmap configuration options are done via your board's
+ resource file.
+
+ If unsure, say N here.
+
config MTD_PHYSMAP_START
hex "Physical start address of flash mapping"
- depends on MTD_PHYSMAP
+ depends on MTD_PHYSMAP_COMPAT
default "0x8000000"
help
This is the physical memory location at which the flash chips
@@ -37,7 +48,7 @@ config MTD_PHYSMAP_START
config MTD_PHYSMAP_LEN
hex "Physical length of flash mapping"
- depends on MTD_PHYSMAP
+ depends on MTD_PHYSMAP_COMPAT
default "0"
help
This is the total length of the mapping of the flash chips on
@@ -51,7 +62,7 @@ config MTD_PHYSMAP_LEN
config MTD_PHYSMAP_BANKWIDTH
int "Bank width in octets"
- depends on MTD_PHYSMAP
+ depends on MTD_PHYSMAP_COMPAT
default "2"
help
This is the total width of the data bus of the flash devices
@@ -259,14 +259,7 @@ static struct platform_driver physmap_flash_driver = {
};
-#ifdef CONFIG_MTD_PHYSMAP_LEN
-#if CONFIG_MTD_PHYSMAP_LEN != 0
-#warning using PHYSMAP compat code
-#define PHYSMAP_COMPAT
-#endif
-#endif
-
-#ifdef PHYSMAP_COMPAT
+#ifdef CONFIG_MTD_PHYSMAP_COMPAT
static struct physmap_flash_data physmap_flash_data = {
.width = CONFIG_MTD_PHYSMAP_BANKWIDTH,
};
@@ -310,7 +303,7 @@ static int __init physmap_init(void)
int err;
err = platform_driver_register(&physmap_flash_driver);
-#ifdef PHYSMAP_COMPAT
+#ifdef CONFIG_MTD_PHYSMAP_COMPAT
if (err == 0)
platform_device_register(&physmap_flash);
#endif
@@ -320,7 +313,7 @@ static int __init physmap_init(void)
static void __exit physmap_exit(void)
{
-#ifdef PHYSMAP_COMPAT
+#ifdef CONFIG_MTD_PHYSMAP_COMPAT
platform_device_unregister(&physmap_flash);
#endif
platform_driver_unregister(&physmap_flash_driver);
@@ -334,8 +327,7 @@ MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>");
MODULE_DESCRIPTION("Generic configurable MTD map driver");
/* legacy platform drivers can't hotplug or coldplg */
-#ifndef PHYSMAP_COMPAT
+#ifndef CONFIG_MTD_PHYSMAP_COMPAT
/* work with hotplug and coldplug */
MODULE_ALIAS("platform:physmap-flash");
#endif
-
The current method for always showing physmap compat address, size, and width is a bit confusing. If length is set to 0, then the address and width are still shown but silently unused. The physmap code itself already has logic which sets compat based on length, so just pull that out and into the Kconfig to make everything clear. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Bryan Wu <Bryan.Wu@analog.com> --- drivers/mtd/maps/Kconfig | 17 ++++++++++++++--- drivers/mtd/maps/physmap.c | 16 ++++------------ 2 files changed, 18 insertions(+), 15 deletions(-)