deleted file mode 100644
@@ -1,207 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2010 Jason Wang <jason77.wang@gmail.com>
- */
-
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/module.h>
-#include <linux/smsc911x.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include "3ds_debugboard.h"
-#include "hardware.h"
-
-/* LAN9217 ethernet base address */
-#define LAN9217_BASE_ADDR(n) (n + 0x0)
-/* External UART */
-#define UARTA_BASE_ADDR(n) (n + 0x8000)
-#define UARTB_BASE_ADDR(n) (n + 0x10000)
-
-#define BOARD_IO_ADDR(n) (n + 0x20000)
-/* LED switchs */
-#define LED_SWITCH_REG 0x00
-/* buttons */
-#define SWITCH_BUTTONS_REG 0x08
-/* status, interrupt */
-#define INTR_STATUS_REG 0x10
-#define INTR_MASK_REG 0x38
-#define INTR_RESET_REG 0x20
-/* magic word for debug CPLD */
-#define MAGIC_NUMBER1_REG 0x40
-#define MAGIC_NUMBER2_REG 0x48
-/* CPLD code version */
-#define CPLD_CODE_VER_REG 0x50
-/* magic word for debug CPLD */
-#define MAGIC_NUMBER3_REG 0x58
-/* module reset register*/
-#define MODULE_RESET_REG 0x60
-/* CPU ID and Personality ID */
-#define MCU_BOARD_ID_REG 0x68
-
-#define MXC_MAX_EXP_IO_LINES 16
-
-/* interrupts like external uart , external ethernet etc*/
-#define EXPIO_INT_ENET 0
-#define EXPIO_INT_XUART_A 1
-#define EXPIO_INT_XUART_B 2
-#define EXPIO_INT_BUTTON_A 3
-#define EXPIO_INT_BUTTON_B 4
-
-static void __iomem *brd_io;
-static struct irq_domain *domain;
-
-static struct resource smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- } , {
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
-};
-
-static struct platform_device smsc_lan9217_device = {
- .name = "smsc911x",
- .id = -1,
- .dev = {
- .platform_data = &smsc911x_config,
- },
- .num_resources = ARRAY_SIZE(smsc911x_resources),
- .resource = smsc911x_resources,
-};
-
-static void mxc_expio_irq_handler(struct irq_desc *desc)
-{
- u32 imr_val;
- u32 int_valid;
- u32 expio_irq;
-
- /* irq = gpio irq number */
- desc->irq_data.chip->irq_mask(&desc->irq_data);
-
- imr_val = imx_readw(brd_io + INTR_MASK_REG);
- int_valid = imx_readw(brd_io + INTR_STATUS_REG) & ~imr_val;
-
- expio_irq = 0;
- for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
- if ((int_valid & 1) == 0)
- continue;
- generic_handle_irq(irq_find_mapping(domain, expio_irq));
- }
-
- desc->irq_data.chip->irq_ack(&desc->irq_data);
- desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * Irq is an expio virtual irq number
- */
-static void expio_mask_irq(struct irq_data *d)
-{
- u16 reg;
- u32 expio = d->hwirq;
-
- reg = imx_readw(brd_io + INTR_MASK_REG);
- reg |= (1 << expio);
- imx_writew(reg, brd_io + INTR_MASK_REG);
-}
-
-static void expio_ack_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
-
- imx_writew(1 << expio, brd_io + INTR_RESET_REG);
- imx_writew(0, brd_io + INTR_RESET_REG);
- expio_mask_irq(d);
-}
-
-static void expio_unmask_irq(struct irq_data *d)
-{
- u16 reg;
- u32 expio = d->hwirq;
-
- reg = imx_readw(brd_io + INTR_MASK_REG);
- reg &= ~(1 << expio);
- imx_writew(reg, brd_io + INTR_MASK_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
- .irq_ack = expio_ack_irq,
- .irq_mask = expio_mask_irq,
- .irq_unmask = expio_unmask_irq,
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
- REGULATOR_SUPPLY("vdd33a", "smsc911x"),
- REGULATOR_SUPPLY("vddvario", "smsc911x"),
-};
-
-int __init mxc_expio_init(u32 base, u32 intr_gpio)
-{
- u32 p_irq = gpio_to_irq(intr_gpio);
- int irq_base;
- int i;
-
- brd_io = ioremap(BOARD_IO_ADDR(base), SZ_4K);
- if (brd_io == NULL)
- return -ENOMEM;
-
- if ((imx_readw(brd_io + MAGIC_NUMBER1_REG) != 0xAAAA) ||
- (imx_readw(brd_io + MAGIC_NUMBER2_REG) != 0x5555) ||
- (imx_readw(brd_io + MAGIC_NUMBER3_REG) != 0xCAFE)) {
- pr_info("3-Stack Debug board not detected\n");
- iounmap(brd_io);
- brd_io = NULL;
- return -ENODEV;
- }
-
- pr_info("3-Stack Debug board detected, rev = 0x%04X\n",
- readw(brd_io + CPLD_CODE_VER_REG));
-
- /*
- * Configure INT line as GPIO input
- */
- gpio_request(intr_gpio, "expio_pirq");
- gpio_direction_input(intr_gpio);
-
- /* disable the interrupt and clear the status */
- imx_writew(0, brd_io + INTR_MASK_REG);
- imx_writew(0xFFFF, brd_io + INTR_RESET_REG);
- imx_writew(0, brd_io + INTR_RESET_REG);
- imx_writew(0x1F, brd_io + INTR_MASK_REG);
-
- irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
- WARN_ON(irq_base < 0);
-
- domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
- &irq_domain_simple_ops, NULL);
- WARN_ON(!domain);
-
- for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
- irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
- irq_clear_status_flags(i, IRQ_NOREQUEST);
- }
- irq_set_irq_type(p_irq, IRQF_TRIGGER_LOW);
- irq_set_chained_handler(p_irq, mxc_expio_irq_handler);
-
- /* Register Lan device on the debugboard */
- regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
- smsc911x_resources[0].start = LAN9217_BASE_ADDR(base);
- smsc911x_resources[0].end = LAN9217_BASE_ADDR(base) + 0x100 - 1;
- smsc911x_resources[1].start = irq_find_mapping(domain, EXPIO_INT_ENET);
- smsc911x_resources[1].end = irq_find_mapping(domain, EXPIO_INT_ENET);
- platform_device_register(&smsc_lan9217_device);
-
- return 0;
-}
deleted file mode 100644
@@ -1,11 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#ifndef __ASM_ARCH_MXC_3DS_DB_H__
-#define __ASM_ARCH_MXC_3DS_DB_H__
-
-extern int __init mxc_expio_init(u32 base, u32 intr_gpio);
-
-#endif /* __ASM_ARCH_MXC_3DS_DB_H__ */
deleted file mode 100644
@@ -1,28 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * Based on code for mobots boards,
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31LILLY_H__
-#define __ASM_ARCH_MXC_BOARD_MX31LILLY_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31lilly_boards {
- MX31LILLY_NOBOARD = 0,
- MX31LILLY_DB = 1,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31lilly_db_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31LILLY_H__ */
deleted file mode 100644
@@ -1,29 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright 2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * Based on code for mobots boards,
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31LITE_H__
-#define __ASM_ARCH_MXC_BOARD_MX31LITE_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31lite_boards {
- MX31LITE_NOBOARD = 0,
- MX31LITE_DB = 1,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31lite_db_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31LITE_H__ */
deleted file mode 100644
@@ -1,30 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__
-#define __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__
-
-#ifndef __ASSEMBLY__
-
-enum mx31moboard_boards {
- MX31NOBOARD = 0,
- MX31DEVBOARD = 1,
- MX31MARXBOT = 2,
- MX31SMARTBOT = 3,
- MX31EYEBOT = 4,
-};
-
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- */
-
-extern void mx31moboard_devboard_init(void);
-extern void mx31moboard_marxbot_init(void);
-extern void mx31moboard_smartbot_init(int board);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_MX31MOBOARD_H__ */
deleted file mode 100644
@@ -1,579 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane@minirl.com)
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/serial_8250.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-#include <linux/mfd/wm8350/audio.h>
-#include <linux/mfd/wm8350/core.h>
-#include <linux/mfd/wm8350/pmic.h>
-#endif
-
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/* Base address of PBC controller */
-#define PBC_BASE_ADDRESS MX31_CS4_BASE_ADDR_VIRT
-
-/* PBC Board interrupt status register */
-#define PBC_INTSTATUS 0x000016
-
-/* PBC Board interrupt current status register */
-#define PBC_INTCURR_STATUS 0x000018
-
-/* PBC Interrupt mask register set address */
-#define PBC_INTMASK_SET 0x00001A
-
-/* PBC Interrupt mask register clear address */
-#define PBC_INTMASK_CLEAR 0x00001C
-
-/* External UART A */
-#define PBC_SC16C652_UARTA 0x010000
-
-/* External UART B */
-#define PBC_SC16C652_UARTB 0x010010
-
-#define PBC_INTSTATUS_REG (PBC_INTSTATUS + PBC_BASE_ADDRESS)
-#define PBC_INTMASK_SET_REG (PBC_INTMASK_SET + PBC_BASE_ADDRESS)
-#define PBC_INTMASK_CLEAR_REG (PBC_INTMASK_CLEAR + PBC_BASE_ADDRESS)
-
-#define EXPIO_INT_XUART_INTA 10
-#define EXPIO_INT_XUART_INTB 11
-
-#define MXC_MAX_EXP_IO_LINES 16
-
-/* CS8900 */
-#define EXPIO_INT_ENET_INT 8
-#define CS4_CS8900_MMIO_START 0x20000
-
-static struct irq_domain *domain;
-
-/*
- * The serial port definition structure.
- */
-static struct plat_serial8250_port serial_platform_data[] = {
- {
- .membase = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTA),
- .mapbase = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTA),
- .uartclk = 14745600,
- .regshift = 0,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
- }, {
- .membase = (void *)(PBC_BASE_ADDRESS + PBC_SC16C652_UARTB),
- .mapbase = (unsigned long)(MX31_CS4_BASE_ADDR + PBC_SC16C652_UARTB),
- .uartclk = 14745600,
- .regshift = 0,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_AUTO_IRQ,
- },
- {},
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = 0,
- .dev = {
- .platform_data = serial_platform_data,
- },
-};
-
-static struct resource mx31ads_cs8900_resources[] __initdata = {
- DEFINE_RES_MEM(MX31_CS4_BASE_ADDR + CS4_CS8900_MMIO_START, SZ_64K),
- DEFINE_RES_IRQ(-1),
-};
-
-static const struct platform_device_info mx31ads_cs8900_devinfo __initconst = {
- .name = "cs89x0",
- .id = 0,
- .res = mx31ads_cs8900_resources,
- .num_res = ARRAY_SIZE(mx31ads_cs8900_resources),
-};
-
-static int __init mxc_init_extuart(void)
-{
- serial_platform_data[0].irq = irq_find_mapping(domain,
- EXPIO_INT_XUART_INTA);
- serial_platform_data[1].irq = irq_find_mapping(domain,
- EXPIO_INT_XUART_INTB);
- return platform_device_register(&serial_device);
-}
-
-static void __init mxc_init_ext_ethernet(void)
-{
- mx31ads_cs8900_resources[1].start =
- irq_find_mapping(domain, EXPIO_INT_ENET_INT);
- mx31ads_cs8900_resources[1].end =
- irq_find_mapping(domain, EXPIO_INT_ENET_INT);
- platform_device_register_full(
- (struct platform_device_info *)&mx31ads_cs8900_devinfo);
-}
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static unsigned int uart_pins[] = {
- MX31_PIN_CTS1__CTS1,
- MX31_PIN_RTS1__RTS1,
- MX31_PIN_TXD1__TXD1,
- MX31_PIN_RXD1__RXD1
-};
-
-static inline void mxc_init_imx_uart(void)
-{
- mxc_iomux_setup_multiple_pins(uart_pins, ARRAY_SIZE(uart_pins), "uart-0");
- imx31_add_imx_uart0(&uart_pdata);
-}
-
-static void mx31ads_expio_irq_handler(struct irq_desc *desc)
-{
- u32 imr_val;
- u32 int_valid;
- u32 expio_irq;
-
- imr_val = imx_readw(PBC_INTMASK_SET_REG);
- int_valid = imx_readw(PBC_INTSTATUS_REG) & imr_val;
-
- expio_irq = 0;
- for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
- if ((int_valid & 1) == 0)
- continue;
-
- generic_handle_irq(irq_find_mapping(domain, expio_irq));
- }
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * @param d an expio virtual irq description
- */
-static void expio_mask_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
- /* mask the interrupt */
- imx_writew(1 << expio, PBC_INTMASK_CLEAR_REG);
- imx_readw(PBC_INTMASK_CLEAR_REG);
-}
-
-/*
- * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
- * @param d an expio virtual irq description
- */
-static void expio_ack_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
- /* clear the interrupt status */
- imx_writew(1 << expio, PBC_INTSTATUS_REG);
-}
-
-/*
- * Enable a expio pin's interrupt by clearing the bit in the imr.
- * @param d an expio virtual irq description
- */
-static void expio_unmask_irq(struct irq_data *d)
-{
- u32 expio = d->hwirq;
- /* unmask the interrupt */
- imx_writew(1 << expio, PBC_INTMASK_SET_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
- .name = "EXPIO(CPLD)",
- .irq_ack = expio_ack_irq,
- .irq_mask = expio_mask_irq,
- .irq_unmask = expio_unmask_irq,
-};
-
-static void __init mx31ads_init_expio(void)
-{
- int irq_base;
- int i, irq;
-
- printk(KERN_INFO "MX31ADS EXPIO(CPLD) hardware\n");
-
- /*
- * Configure INT line as GPIO input
- */
- mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_GPIO1_4, IOMUX_CONFIG_GPIO), "expio");
-
- /* disable the interrupt and clear the status */
- imx_writew(0xFFFF, PBC_INTMASK_CLEAR_REG);
- imx_writew(0xFFFF, PBC_INTSTATUS_REG);
-
- irq_base = irq_alloc_descs(-1, 0, MXC_MAX_EXP_IO_LINES, numa_node_id());
- WARN_ON(irq_base < 0);
-
- domain = irq_domain_add_legacy(NULL, MXC_MAX_EXP_IO_LINES, irq_base, 0,
- &irq_domain_simple_ops, NULL);
- WARN_ON(!domain);
-
- for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
- irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
- irq_clear_status_flags(i, IRQ_NOREQUEST);
- }
- irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_4));
- irq_set_irq_type(irq, IRQ_TYPE_LEVEL_HIGH);
- irq_set_chained_handler(irq, mx31ads_expio_irq_handler);
-}
-
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
-/* This section defines setup for the Wolfson Microelectronics
- * 1133-EV1 PMU/audio board. When other PMU boards are supported the
- * regulator definitions may be shared with them, but for now they can
- * only be used with this board so would generate warnings about
- * unused statics and some of the configuration is specific to this
- * module.
- */
-
-/* CPU */
-static struct regulator_consumer_supply sw1a_consumers[] = {
- {
- .supply = "cpu_vcc",
- }
-};
-
-static struct regulator_init_data sw1a_data = {
- .constraints = {
- .name = "SW1A",
- .min_uV = 1275000,
- .max_uV = 1600000,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_MODE,
- .valid_modes_mask = REGULATOR_MODE_NORMAL |
- REGULATOR_MODE_FAST,
- .state_mem = {
- .uV = 1400000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .initial_state = PM_SUSPEND_MEM,
- .always_on = 1,
- .boot_on = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(sw1a_consumers),
- .consumer_supplies = sw1a_consumers,
-};
-
-/* System IO - High */
-static struct regulator_init_data viohi_data = {
- .constraints = {
- .name = "VIOHO",
- .min_uV = 2800000,
- .max_uV = 2800000,
- .state_mem = {
- .uV = 2800000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .initial_state = PM_SUSPEND_MEM,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-/* System IO - Low */
-static struct regulator_init_data violo_data = {
- .constraints = {
- .name = "VIOLO",
- .min_uV = 1800000,
- .max_uV = 1800000,
- .state_mem = {
- .uV = 1800000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .initial_state = PM_SUSPEND_MEM,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-/* DDR RAM */
-static struct regulator_init_data sw2a_data = {
- .constraints = {
- .name = "SW2A",
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .state_mem = {
- .uV = 1800000,
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 1,
- },
- .state_disk = {
- .mode = REGULATOR_MODE_NORMAL,
- .enabled = 0,
- },
- .always_on = 1,
- .boot_on = 1,
- .initial_state = PM_SUSPEND_MEM,
- },
-};
-
-static struct regulator_init_data ldo1_data = {
- .constraints = {
- .name = "VCAM/VMMC1/VMMC2",
- .min_uV = 2800000,
- .max_uV = 2800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- .apply_uV = 1,
- },
-};
-
-static struct regulator_consumer_supply ldo2_consumers[] = {
- { .supply = "AVDD", .dev_name = "1-001a" },
- { .supply = "HPVDD", .dev_name = "1-001a" },
-};
-
-/* CODEC and SIM */
-static struct regulator_init_data ldo2_data = {
- .constraints = {
- .name = "VESIM/VSIM/AVDD",
- .min_uV = 3300000,
- .max_uV = 3300000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- .apply_uV = 1,
- },
- .num_consumer_supplies = ARRAY_SIZE(ldo2_consumers),
- .consumer_supplies = ldo2_consumers,
-};
-
-/* General */
-static struct regulator_init_data vdig_data = {
- .constraints = {
- .name = "VDIG",
- .min_uV = 1500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .apply_uV = 1,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-/* Tranceivers */
-static struct regulator_init_data ldo4_data = {
- .constraints = {
- .name = "VRF1/CVDD_2.775",
- .min_uV = 2500000,
- .max_uV = 2500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .apply_uV = 1,
- .always_on = 1,
- .boot_on = 1,
- },
-};
-
-static struct wm8350_led_platform_data wm8350_led_data = {
- .name = "wm8350:white",
- .default_trigger = "heartbeat",
- .max_uA = 27899,
-};
-
-static struct wm8350_audio_platform_data imx32ads_wm8350_setup = {
- .vmid_discharge_msecs = 1000,
- .drain_msecs = 30,
- .cap_discharge_msecs = 700,
- .vmid_charge_msecs = 700,
- .vmid_s_curve = WM8350_S_CURVE_SLOW,
- .dis_out4 = WM8350_DISCHARGE_SLOW,
- .dis_out3 = WM8350_DISCHARGE_SLOW,
- .dis_out2 = WM8350_DISCHARGE_SLOW,
- .dis_out1 = WM8350_DISCHARGE_SLOW,
- .vroi_out4 = WM8350_TIE_OFF_500R,
- .vroi_out3 = WM8350_TIE_OFF_500R,
- .vroi_out2 = WM8350_TIE_OFF_500R,
- .vroi_out1 = WM8350_TIE_OFF_500R,
- .vroi_enable = 0,
- .codec_current_on = WM8350_CODEC_ISEL_1_0,
- .codec_current_standby = WM8350_CODEC_ISEL_0_5,
- .codec_current_charge = WM8350_CODEC_ISEL_1_5,
-};
-
-static int mx31_wm8350_init(struct wm8350 *wm8350)
-{
- wm8350_gpio_config(wm8350, 0, WM8350_GPIO_DIR_IN,
- WM8350_GPIO0_PWR_ON_IN, WM8350_GPIO_ACTIVE_LOW,
- WM8350_GPIO_PULL_UP, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_ON);
-
- wm8350_gpio_config(wm8350, 3, WM8350_GPIO_DIR_IN,
- WM8350_GPIO3_PWR_OFF_IN, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_ON);
-
- wm8350_gpio_config(wm8350, 4, WM8350_GPIO_DIR_IN,
- WM8350_GPIO4_MR_IN, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 7, WM8350_GPIO_DIR_IN,
- WM8350_GPIO7_HIBERNATE_IN, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_DOWN, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 6, WM8350_GPIO_DIR_OUT,
- WM8350_GPIO6_SDOUT_OUT, WM8350_GPIO_ACTIVE_HIGH,
- WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 8, WM8350_GPIO_DIR_OUT,
- WM8350_GPIO8_VCC_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
- WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_gpio_config(wm8350, 9, WM8350_GPIO_DIR_OUT,
- WM8350_GPIO9_BATT_FAULT_OUT, WM8350_GPIO_ACTIVE_LOW,
- WM8350_GPIO_PULL_NONE, WM8350_GPIO_INVERT_OFF,
- WM8350_GPIO_DEBOUNCE_OFF);
-
- wm8350_register_regulator(wm8350, WM8350_DCDC_1, &sw1a_data);
- wm8350_register_regulator(wm8350, WM8350_DCDC_3, &viohi_data);
- wm8350_register_regulator(wm8350, WM8350_DCDC_4, &violo_data);
- wm8350_register_regulator(wm8350, WM8350_DCDC_6, &sw2a_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_1, &ldo1_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_2, &ldo2_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_3, &vdig_data);
- wm8350_register_regulator(wm8350, WM8350_LDO_4, &ldo4_data);
-
- /* LEDs */
- wm8350_dcdc_set_slot(wm8350, WM8350_DCDC_5, 1, 1,
- WM8350_DC5_ERRACT_SHUTDOWN_CONV);
- wm8350_isink_set_flash(wm8350, WM8350_ISINK_A,
- WM8350_ISINK_FLASH_DISABLE,
- WM8350_ISINK_FLASH_TRIG_BIT,
- WM8350_ISINK_FLASH_DUR_32MS,
- WM8350_ISINK_FLASH_ON_INSTANT,
- WM8350_ISINK_FLASH_OFF_INSTANT,
- WM8350_ISINK_FLASH_MODE_EN);
- wm8350_dcdc25_set_mode(wm8350, WM8350_DCDC_5,
- WM8350_ISINK_MODE_BOOST,
- WM8350_ISINK_ILIM_NORMAL,
- WM8350_DC5_RMP_20V,
- WM8350_DC5_FBSRC_ISINKA);
- wm8350_register_led(wm8350, 0, WM8350_DCDC_5, WM8350_ISINK_A,
- &wm8350_led_data);
-
- wm8350->codec.platform_data = &imx32ads_wm8350_setup;
-
- regulator_has_full_constraints();
-
- return 0;
-}
-
-static struct wm8350_platform_data __initdata mx31_wm8350_pdata = {
- .init = mx31_wm8350_init,
-};
-#endif
-
-static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = {
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
- {
- I2C_BOARD_INFO("wm8350", 0x1a),
- .platform_data = &mx31_wm8350_pdata,
- /* irq number is run-time assigned */
- },
-#endif
-};
-
-static void __init mxc_init_i2c(void)
-{
-#ifdef CONFIG_MACH_MX31ADS_WM1133_EV1
- mx31ads_i2c1_devices[0].irq =
- gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
-#endif
- i2c_register_board_info(1, mx31ads_i2c1_devices,
- ARRAY_SIZE(mx31ads_i2c1_devices));
-
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MOSI, IOMUX_CONFIG_ALT1));
- mxc_iomux_mode(IOMUX_MODE(MX31_PIN_CSPI2_MISO, IOMUX_CONFIG_ALT1));
-
- imx31_add_imx_i2c1(NULL);
-}
-
-static unsigned int ssi_pins[] = {
- MX31_PIN_SFS5__SFS5,
- MX31_PIN_SCK5__SCK5,
- MX31_PIN_SRXD5__SRXD5,
- MX31_PIN_STXD5__STXD5,
-};
-
-static void __init mxc_init_audio(void)
-{
- imx31_add_imx_ssi(0, NULL);
- mxc_iomux_setup_multiple_pins(ssi_pins, ARRAY_SIZE(ssi_pins), "ssi");
-}
-
-/*
- * Static mappings, starting from the CS4 start address up to the start address
- * of the CS8900.
- */
-static struct map_desc mx31ads_io_desc[] __initdata = {
- {
- .virtual = (unsigned long)MX31_CS4_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX31_CS4_BASE_ADDR),
- .length = CS4_CS8900_MMIO_START,
- .type = MT_DEVICE
- },
-};
-
-static void __init mx31ads_map_io(void)
-{
- mx31_map_io();
- iotable_init(mx31ads_io_desc, ARRAY_SIZE(mx31ads_io_desc));
-}
-
-static void __init mx31ads_init(void)
-{
- imx31_soc_init();
-
- mxc_init_imx_uart();
- mxc_init_audio();
-}
-
-static void __init mx31ads_late(void)
-{
- mx31ads_init_expio();
- mxc_init_extuart();
- mxc_init_i2c();
- mxc_init_ext_ethernet();
-}
-
-static void __init mx31ads_timer_init(void)
-{
- mx31_clocks_init(26000000);
-}
-
-MACHINE_START(MX31ADS, "Freescale MX31ADS")
- /* Maintainer: Freescale Semiconductor, Inc. */
- .atag_offset = 0x100,
- .map_io = mx31ads_map_io,
- .init_early = imx31_init_early,
- .init_irq = mx31_init_irq,
- .init_time = mx31ads_timer_init,
- .init_machine = mx31ads_init,
- .init_late = mx31ads_late,
- .restart = mxc_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,154 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LogicPD i.MX31 SOM-LV development board support
- *
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- *
- * based on code for other MX31 boards,
- *
- * Copyright 2005-2007 Freescale Semiconductor
- * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "board-mx31lite.h"
-#include "common.h"
-#include "devices-imx31.h"
-#include "hardware.h"
-#include "iomux-mx3.h"
-
-/*
- * This file contains board-specific initialization routines for the
- * LogicPD i.MX31 SOM-LV development board, aka 'LiteKit'.
- * If you design an own baseboard for the module, use this file as base
- * for support code.
- */
-
-static unsigned int litekit_db_board_pins[] __initdata = {
- /* SDHC1 */
- MX31_PIN_SD1_DATA0__SD1_DATA0,
- MX31_PIN_SD1_DATA1__SD1_DATA1,
- MX31_PIN_SD1_DATA2__SD1_DATA2,
- MX31_PIN_SD1_DATA3__SD1_DATA3,
- MX31_PIN_SD1_CLK__SD1_CLK,
- MX31_PIN_SD1_CMD__SD1_CMD,
-};
-
-/* MMC */
-
-static int gpio_det, gpio_wp;
-
-#define MMC_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
- PAD_CTL_ODE_CMOS)
-
-static int mxc_mmc1_get_ro(struct device *dev)
-{
- return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_GPIO1_6));
-}
-
-static int mxc_mmc1_init(struct device *dev,
- irq_handler_t detect_irq, void *data)
-{
- int ret;
-
- gpio_det = IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1);
- gpio_wp = IOMUX_TO_GPIO(MX31_PIN_GPIO1_6);
-
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA0,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA1,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA2,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_DATA3,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_CMD,
- MMC_PAD_CFG | PAD_CTL_PUE_PUD | PAD_CTL_100K_PU);
- mxc_iomux_set_pad(MX31_PIN_SD1_CLK, MMC_PAD_CFG);
-
- ret = gpio_request(gpio_det, "MMC detect");
- if (ret)
- return ret;
-
- ret = gpio_request(gpio_wp, "MMC w/p");
- if (ret)
- goto exit_free_det;
-
- gpio_direction_input(gpio_det);
- gpio_direction_input(gpio_wp);
-
- ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)),
- detect_irq,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC detect", data);
- if (ret)
- goto exit_free_wp;
-
- return 0;
-
-exit_free_wp:
- gpio_free(gpio_wp);
-
-exit_free_det:
- gpio_free(gpio_det);
-
- return ret;
-}
-
-static void mxc_mmc1_exit(struct device *dev, void *data)
-{
- gpio_free(gpio_det);
- gpio_free(gpio_wp);
- free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_DCD_DCE1)), data);
-}
-
-static const struct imxmmc_platform_data mmc_pdata __initconst = {
- .get_ro = mxc_mmc1_get_ro,
- .init = mxc_mmc1_init,
- .exit = mxc_mmc1_exit,
-};
-
-/* GPIO LEDs */
-
-static const struct gpio_led litekit_leds[] __initconst = {
- {
- .name = "GPIO0",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_COMPARE),
- .active_low = 1,
- .default_state = LEDS_GPIO_DEFSTATE_OFF,
- },
- {
- .name = "GPIO1",
- .gpio = IOMUX_TO_GPIO(MX31_PIN_CAPTURE),
- .active_low = 1,
- .default_state = LEDS_GPIO_DEFSTATE_OFF,
- }
-};
-
-static const struct gpio_led_platform_data
- litekit_led_platform_data __initconst = {
- .leds = litekit_leds,
- .num_leds = ARRAY_SIZE(litekit_leds),
-};
-
-void __init mx31lite_db_init(void)
-{
- mxc_iomux_setup_multiple_pins(litekit_db_board_pins,
- ARRAY_SIZE(litekit_db_board_pins),
- "development board pins");
- imx31_add_mxc_mmc(0, &mmc_pdata);
- gpio_led_register_device(-1, &litekit_led_platform_data);
- imx31_add_imx2_wdt();
- imx31_add_mxc_rtc();
-}
deleted file mode 100644
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __PCM037_H__
-#define __PCM037_H__
-
-enum pcm037_board_variant {
- PCM037_PCM970,
- PCM037_EET,
-};
-
-extern enum pcm037_board_variant pcm037_variant(void);
-
-#ifdef CONFIG_MACH_PCM037_EET
-int pcm037_eet_init_devices(void);
-#else
-static inline int pcm037_eet_init_devices(void) { return 0; }
-#endif
-
-#endif
i.MX31 is a devicetree only platform. Remove remaining i.MX31 board code. Signed-off-by: Fabio Estevam <festevam@gmail.com> --- arch/arm/mach-imx/3ds_debugboard.c | 207 --------- arch/arm/mach-imx/3ds_debugboard.h | 11 - arch/arm/mach-imx/board-mx31lilly.h | 28 -- arch/arm/mach-imx/board-mx31lite.h | 29 -- arch/arm/mach-imx/board-mx31moboard.h | 30 -- arch/arm/mach-imx/mach-mx31ads.c | 579 -------------------------- arch/arm/mach-imx/mx31lite-db.c | 154 ------- arch/arm/mach-imx/pcm037.h | 18 - 8 files changed, 1056 deletions(-) delete mode 100644 arch/arm/mach-imx/3ds_debugboard.c delete mode 100644 arch/arm/mach-imx/3ds_debugboard.h delete mode 100644 arch/arm/mach-imx/board-mx31lilly.h delete mode 100644 arch/arm/mach-imx/board-mx31lite.h delete mode 100644 arch/arm/mach-imx/board-mx31moboard.h delete mode 100644 arch/arm/mach-imx/mach-mx31ads.c delete mode 100644 arch/arm/mach-imx/mx31lite-db.c delete mode 100644 arch/arm/mach-imx/pcm037.h