| Message ID | 20171214130941.26666-3-kishon@ti.com |
|---|---|
| State | New |
| Headers | show |
| Series | mmc: sdhci-omap: Add UHS/HS200 mode support | expand |
On 14/12/17 15:09, Kishon Vijay Abraham I wrote: > card_busy ops is used by mmc core in > 1) mmc_set_uhs_voltage to verify voltage switch > 2) __mmc_start_request/mmc_poll_for_busy to check the card busy status > > While only DAT0 can be used to check the card busy status (in '2' above), > CMD and DAT[0..3] is used to verify voltage switch (in '1' above). > > The voltage switching sequence for AM572x platform is mentioned > in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of > AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM > (SPRUHZ6I - October 2014–Revised April 2017 [1]). > > Add card_busy host ops in sdhci_omap that checks for both CMD and > DAT[0..3]. card_busy here returns true if one of CMD and DAT[0..3] is > low though during voltage switch sequence all of CMD and DAT[0..3] has > to be low (however haven't observed a case where some DAT lines are low > and some are high). Isn't it better to check DAT0 only since that is all that is defined for 'busy'. > > In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON > should also be set after switching to 1.8v which is also taken > care in the card_busy ops. > > [1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf > > Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> > --- > drivers/mmc/host/sdhci-omap.c | 62 +++++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 62 insertions(+) > > diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c > index 96985786cadf..defe4eac020d 100644 > --- a/drivers/mmc/host/sdhci-omap.c > +++ b/drivers/mmc/host/sdhci-omap.c > @@ -31,11 +31,20 @@ > #define SDHCI_OMAP_CON 0x12c > #define CON_DW8 BIT(5) > #define CON_DMA_MASTER BIT(20) > +#define CON_CLKEXTFREE BIT(16) > +#define CON_PADEN BIT(15) > #define CON_INIT BIT(1) > #define CON_OD BIT(0) > > #define SDHCI_OMAP_CMD 0x20c > > +#define SDHCI_OMAP_PSTATE 0x0224 > +#define PSTATE_CLEV BIT(24) > +#define PSTATE_DLEV_SHIFT 20 > +#define PSTATE_DLEV_DAT(x) (1 << (PSTATE_DLEV_SHIFT + (x))) > +#define PSTATE_DLEV (PSTATE_DLEV_DAT(0) | PSTATE_DLEV_DAT(1) | \ > + PSTATE_DLEV_DAT(2) | PSTATE_DLEV_DAT(3)) > + > #define SDHCI_OMAP_HCTL 0x228 > #define HCTL_SDBP BIT(8) > #define HCTL_SDVS_SHIFT 9 > @@ -191,6 +200,58 @@ static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host, > } > } > > +static int sdhci_omap_card_busy(struct mmc_host *mmc) > +{ > + int i; > + u32 reg, ac12; > + int ret = true; > + struct sdhci_host *host = mmc_priv(mmc); > + struct sdhci_pltfm_host *pltfm_host; > + struct sdhci_omap_host *omap_host; > + u32 ier = host->ier; > + > + pltfm_host = sdhci_priv(host); > + omap_host = sdhci_pltfm_priv(pltfm_host); > + > + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); > + ac12 = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12); > + reg &= ~CON_CLKEXTFREE; > + if (ac12 & AC12_V1V8_SIGEN) > + reg |= CON_CLKEXTFREE; > + reg |= CON_PADEN; > + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); > + > + disable_irq(host->irq); > + ier |= SDHCI_INT_CARD_INT; > + sdhci_writel(host, ier, SDHCI_INT_ENABLE); > + sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE); > + > + for (i = 0; i < 5; i++) { > + /* > + * Delay is required for PSTATE to correctly reflect > + * DLEV/CLEV values after PADEM is set. > + */ > + usleep_range(100, 200); > + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_PSTATE); > + if ((reg & PSTATE_CLEV) && > + ((reg & PSTATE_DLEV) == PSTATE_DLEV)) { > + ret = false; > + goto ret; 'break' is better than 'goto' > + } > + } > + > +ret: > + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); > + reg &= ~(CON_CLKEXTFREE | CON_PADEN); > + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); > + > + sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); > + sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); > + enable_irq(host->irq); > + > + return ret; > +} > + > static int sdhci_omap_start_signal_voltage_switch(struct mmc_host *mmc, > struct mmc_ios *ios) > { > @@ -562,6 +623,7 @@ static int sdhci_omap_probe(struct platform_device *pdev) > host->mmc_host_ops.start_signal_voltage_switch = > sdhci_omap_start_signal_voltage_switch; > host->mmc_host_ops.set_ios = sdhci_omap_set_ios; > + host->mmc_host_ops.card_busy = sdhci_omap_card_busy; > > sdhci_read_caps(host); > host->caps |= SDHCI_CAN_DO_ADMA2; >
diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c index 96985786cadf..defe4eac020d 100644 --- a/drivers/mmc/host/sdhci-omap.c +++ b/drivers/mmc/host/sdhci-omap.c @@ -31,11 +31,20 @@ #define SDHCI_OMAP_CON 0x12c #define CON_DW8 BIT(5) #define CON_DMA_MASTER BIT(20) +#define CON_CLKEXTFREE BIT(16) +#define CON_PADEN BIT(15) #define CON_INIT BIT(1) #define CON_OD BIT(0) #define SDHCI_OMAP_CMD 0x20c +#define SDHCI_OMAP_PSTATE 0x0224 +#define PSTATE_CLEV BIT(24) +#define PSTATE_DLEV_SHIFT 20 +#define PSTATE_DLEV_DAT(x) (1 << (PSTATE_DLEV_SHIFT + (x))) +#define PSTATE_DLEV (PSTATE_DLEV_DAT(0) | PSTATE_DLEV_DAT(1) | \ + PSTATE_DLEV_DAT(2) | PSTATE_DLEV_DAT(3)) + #define SDHCI_OMAP_HCTL 0x228 #define HCTL_SDBP BIT(8) #define HCTL_SDVS_SHIFT 9 @@ -191,6 +200,58 @@ static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host, } } +static int sdhci_omap_card_busy(struct mmc_host *mmc) +{ + int i; + u32 reg, ac12; + int ret = true; + struct sdhci_host *host = mmc_priv(mmc); + struct sdhci_pltfm_host *pltfm_host; + struct sdhci_omap_host *omap_host; + u32 ier = host->ier; + + pltfm_host = sdhci_priv(host); + omap_host = sdhci_pltfm_priv(pltfm_host); + + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); + ac12 = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12); + reg &= ~CON_CLKEXTFREE; + if (ac12 & AC12_V1V8_SIGEN) + reg |= CON_CLKEXTFREE; + reg |= CON_PADEN; + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); + + disable_irq(host->irq); + ier |= SDHCI_INT_CARD_INT; + sdhci_writel(host, ier, SDHCI_INT_ENABLE); + sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE); + + for (i = 0; i < 5; i++) { + /* + * Delay is required for PSTATE to correctly reflect + * DLEV/CLEV values after PADEM is set. + */ + usleep_range(100, 200); + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_PSTATE); + if ((reg & PSTATE_CLEV) && + ((reg & PSTATE_DLEV) == PSTATE_DLEV)) { + ret = false; + goto ret; + } + } + +ret: + reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON); + reg &= ~(CON_CLKEXTFREE | CON_PADEN); + sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg); + + sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); + sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); + enable_irq(host->irq); + + return ret; +} + static int sdhci_omap_start_signal_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios) { @@ -562,6 +623,7 @@ static int sdhci_omap_probe(struct platform_device *pdev) host->mmc_host_ops.start_signal_voltage_switch = sdhci_omap_start_signal_voltage_switch; host->mmc_host_ops.set_ios = sdhci_omap_set_ios; + host->mmc_host_ops.card_busy = sdhci_omap_card_busy; sdhci_read_caps(host); host->caps |= SDHCI_CAN_DO_ADMA2;
card_busy ops is used by mmc core in 1) mmc_set_uhs_voltage to verify voltage switch 2) __mmc_start_request/mmc_poll_for_busy to check the card busy status While only DAT0 can be used to check the card busy status (in '2' above), CMD and DAT[0..3] is used to verify voltage switch (in '1' above). The voltage switching sequence for AM572x platform is mentioned in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM (SPRUHZ6I - October 2014–Revised April 2017 [1]). Add card_busy host ops in sdhci_omap that checks for both CMD and DAT[0..3]. card_busy here returns true if one of CMD and DAT[0..3] is low though during voltage switch sequence all of CMD and DAT[0..3] has to be low (however haven't observed a case where some DAT lines are low and some are high). In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON should also be set after switching to 1.8v which is also taken care in the card_busy ops. [1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- drivers/mmc/host/sdhci-omap.c | 62 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+)