Message ID | 1338376389-32256-1-git-send-email-javier.martin@vista-silicon.com |
---|---|
State | New |
Headers | show |
On Wed, May 30, 2012 at 01:13:09PM +0200, Javier Martin wrote: > Some GPIOs in Visstrim M10 are used without being registered. > This leads to USB and video malfunctions. This patch registers > those GPIOs to solve the issue. > > Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> > --- > arch/arm/mach-imx/mach-imx27_visstrim_m10.c | 13 ++++++++----- > 1 files changed, 8 insertions(+), 5 deletions(-) > > diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c > index e8741f9..db4aa6f 100644 > --- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c > +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c > @@ -116,6 +116,8 @@ static const int visstrim_m10_pins[] __initconst = { > PB23_PF_USB_PWR, > PB24_PF_USB_OC, > /* CSI */ > + TVP5150_RSTN | GPIO_GPIO | GPIO_OUT, > + TVP5150_PWDN | GPIO_GPIO | GPIO_OUT, > PB10_PF_CSI_D0, > PB11_PF_CSI_D1, > PB12_PF_CSI_D2, > @@ -182,10 +184,10 @@ static void __init visstrim_camera_init(void) > int dma; > > /* Initialize tvp5150 gpios */ > - mxc_gpio_mode(TVP5150_RSTN | GPIO_GPIO | GPIO_OUT); > - mxc_gpio_mode(TVP5150_PWDN | GPIO_GPIO | GPIO_OUT); > - gpio_set_value(TVP5150_RSTN, 1); > - gpio_set_value(TVP5150_PWDN, 0); > + gpio_request_one(TVP5150_RSTN, GPIOF_DIR_OUT | GPIOF_INIT_HIGH, > + "tvp5150_rstn"); > + gpio_request_one(TVP5150_PWDN, GPIOF_DIR_OUT | GPIOF_INIT_LOW, > + "tvp5150_pwdn"); > ndelay(1); > > gpio_set_value(TVP5150_PWDN, 1); > @@ -414,7 +416,8 @@ static struct i2c_board_info visstrim_m10_i2c_devices[] = { > /* USB OTG */ > static int otg_phy_init(struct platform_device *pdev) > { > - gpio_set_value(OTG_PHY_CS_GPIO, 0); > + gpio_request_one(OTG_PHY_CS_GPIO, GPIOF_DIR_OUT | GPIOF_INIT_LOW, > + "usbotg_cs"); Could you please combine all gpios for your board into a single gpio_request_array? Then you can add proper error checking aswell without much overhead. Sascha
diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c index e8741f9..db4aa6f 100644 --- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c @@ -116,6 +116,8 @@ static const int visstrim_m10_pins[] __initconst = { PB23_PF_USB_PWR, PB24_PF_USB_OC, /* CSI */ + TVP5150_RSTN | GPIO_GPIO | GPIO_OUT, + TVP5150_PWDN | GPIO_GPIO | GPIO_OUT, PB10_PF_CSI_D0, PB11_PF_CSI_D1, PB12_PF_CSI_D2, @@ -182,10 +184,10 @@ static void __init visstrim_camera_init(void) int dma; /* Initialize tvp5150 gpios */ - mxc_gpio_mode(TVP5150_RSTN | GPIO_GPIO | GPIO_OUT); - mxc_gpio_mode(TVP5150_PWDN | GPIO_GPIO | GPIO_OUT); - gpio_set_value(TVP5150_RSTN, 1); - gpio_set_value(TVP5150_PWDN, 0); + gpio_request_one(TVP5150_RSTN, GPIOF_DIR_OUT | GPIOF_INIT_HIGH, + "tvp5150_rstn"); + gpio_request_one(TVP5150_PWDN, GPIOF_DIR_OUT | GPIOF_INIT_LOW, + "tvp5150_pwdn"); ndelay(1); gpio_set_value(TVP5150_PWDN, 1); @@ -414,7 +416,8 @@ static struct i2c_board_info visstrim_m10_i2c_devices[] = { /* USB OTG */ static int otg_phy_init(struct platform_device *pdev) { - gpio_set_value(OTG_PHY_CS_GPIO, 0); + gpio_request_one(OTG_PHY_CS_GPIO, GPIOF_DIR_OUT | GPIOF_INIT_LOW, + "usbotg_cs"); mdelay(10);
Some GPIOs in Visstrim M10 are used without being registered. This leads to USB and video malfunctions. This patch registers those GPIOs to solve the issue. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> --- arch/arm/mach-imx/mach-imx27_visstrim_m10.c | 13 ++++++++----- 1 files changed, 8 insertions(+), 5 deletions(-)