| Message ID | 20230831101513.2042773-1-Naresh.Solanki@9elements.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v2,1/2] dt-bindings: i2c: Add custom properties for MAX7357/MAX7358 | expand |
On 31/08/2023 12:15, Naresh Solanki wrote: > From: Patrick Rudolph <patrick.rudolph@9elements.com> > > Both chips have a configuration register to enable additional > features. These features aren't enabled by default & its up to > board designer to enable the same. > > Add booleans for: > - maxim,isolate-stuck-channel > - maxim,send-flush-out-sequence > - maxim,preconnection-wiggle-test-enable > > Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> > Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com> Subject: still did not improve. You waited exactly 30 minutes for my feedback after sending your response. > --- > Changes in V2: > - Update properties. > --- > .../bindings/i2c/i2c-mux-pca954x.yaml | 31 +++++++++++++++++++ > 1 file changed, 31 insertions(+) > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > index 2d7bb998b0e9..fa73eadfdf7b 100644 > --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > @@ -71,6 +71,23 @@ properties: > description: A voltage regulator supplying power to the chip. On PCA9846 > the regulator supplies power to VDD2 (core logic) and optionally to VDD1. > > + maxim,isolate-stuck-channel: > + type: boolean > + description: Allows to use non faulty channels while a stuck channel is > + isolated from the upstream bus. If not set all channels are isolated from > + the upstream bus until the fault is cleared. Nothing improved here. As I said, please provide arguments or drop this property. > + > + maxim,send-flush-out-sequence: > + type: boolean > + description: Send a flush-out sequence to stuck auxiliary buses > + automatically after a stuck channel is being detected. Ditto > + > + maxim,preconnection-wiggle-test-enable: > + type: boolean > + description: Send a STOP condition to the auxiliary buses when the switch > + register activates a channel to detect a stuck high fault. On fault the > + channel is isolated from the upstream bus. Ditto Best regards, Krzysztof
Hi On Thu, 31 Aug 2023 at 17:33, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 31/08/2023 12:15, Naresh Solanki wrote: > > From: Patrick Rudolph <patrick.rudolph@9elements.com> > > > > Both chips have a configuration register to enable additional > > features. These features aren't enabled by default & it's up to > > board designer to enable the same. > > > > Add booleans for: > > - maxim,isolate-stuck-channel > > - maxim,send-flush-out-sequence > > - maxim,preconnection-wiggle-test-enable > > > > Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com> > > Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com> > > Subject: still did not improve. You waited exactly 30 minutes for my > feedback after sending your response. Will update the subject prefix to: 'dt-bindings: i2c: pca954x:' Also I'm adding three properties here so I guess 'Add custom properties..' should be fine. If you have a better suggestion then please let me know. > > > > > --- > > Changes in V2: > > - Update properties. > > --- > > .../bindings/i2c/i2c-mux-pca954x.yaml | 31 +++++++++++++++++++ > > 1 file changed, 31 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > > index 2d7bb998b0e9..fa73eadfdf7b 100644 > > --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > > +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > > @@ -71,6 +71,23 @@ properties: > > description: A voltage regulator supplying power to the chip. On PCA9846 > > the regulator supplies power to VDD2 (core logic) and optionally to VDD1. > > > > + maxim,isolate-stuck-channel: > > + type: boolean > > + description: Allows to use non faulty channels while a stuck channel is > > + isolated from the upstream bus. If not set all channels are isolated from > > + the upstream bus until the fault is cleared. > > Nothing improved here. As I said, please provide arguments or drop this > property. These features cannot be enabled by default because doing so may lead to unexpected behavior, such as bus disconnections(although that wasn't expected). These features should only be enabled after they have been validated by the board designer. Therefore, they cannot be enabled by default. Regards, Naresh > > > + > > + maxim,send-flush-out-sequence: > > + type: boolean > > + description: Send a flush-out sequence to stuck auxiliary buses > > + automatically after a stuck channel is being detected. > > Ditto > > > + > > + maxim,preconnection-wiggle-test-enable: > > + type: boolean > > + description: Send a STOP condition to the auxiliary buses when the switch > > + register activates a channel to detect a stuck high fault. On fault the > > + channel is isolated from the upstream bus. > > Ditto > > > Best regards, > Krzysztof >
On 11/09/2023 12:31, Naresh Solanki wrote: >>> diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml >>> index 2d7bb998b0e9..fa73eadfdf7b 100644 >>> --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml >>> +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml >>> @@ -71,6 +71,23 @@ properties: >>> description: A voltage regulator supplying power to the chip. On PCA9846 >>> the regulator supplies power to VDD2 (core logic) and optionally to VDD1. >>> >>> + maxim,isolate-stuck-channel: >>> + type: boolean >>> + description: Allows to use non faulty channels while a stuck channel is >>> + isolated from the upstream bus. If not set all channels are isolated from >>> + the upstream bus until the fault is cleared. >> >> Nothing improved here. As I said, please provide arguments or drop this >> property. > These features cannot be enabled by default because doing so may lead > to unexpected behavior, such as bus disconnections(although that > wasn't expected). > These features should only be enabled after they have been validated > by the board designer. > Therefore, they cannot be enabled by default. And what is needed to validate them for given board? IOW, what changes in hardware design that it can or cannot be used? Best regards, Krzysztof
Hi On Mon, 11 Sept 2023 at 16:13, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 11/09/2023 12:31, Naresh Solanki wrote: > > >>> diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > >>> index 2d7bb998b0e9..fa73eadfdf7b 100644 > >>> --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > >>> +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml > >>> @@ -71,6 +71,23 @@ properties: > >>> description: A voltage regulator supplying power to the chip. On PCA9846 > >>> the regulator supplies power to VDD2 (core logic) and optionally to VDD1. > >>> > >>> + maxim,isolate-stuck-channel: > >>> + type: boolean > >>> + description: Allows to use non faulty channels while a stuck channel is > >>> + isolated from the upstream bus. If not set all channels are isolated from > >>> + the upstream bus until the fault is cleared. > >> > >> Nothing improved here. As I said, please provide arguments or drop this > >> property. > > These features cannot be enabled by default because doing so may lead > > to unexpected behavior, such as bus disconnections(although that > > wasn't expected). > > These features should only be enabled after they have been validated > > by the board designer. > > Therefore, they cannot be enabled by default. > > And what is needed to validate them for given board? IOW, what changes > in hardware design that it can or cannot be used? Enabling PRECONNECT_TEST in my setup didn't work Although this wasn't expected. Regards, Naresh > > Best regards, > Krzysztof >
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml index 2d7bb998b0e9..fa73eadfdf7b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml @@ -71,6 +71,23 @@ properties: description: A voltage regulator supplying power to the chip. On PCA9846 the regulator supplies power to VDD2 (core logic) and optionally to VDD1. + maxim,isolate-stuck-channel: + type: boolean + description: Allows to use non faulty channels while a stuck channel is + isolated from the upstream bus. If not set all channels are isolated from + the upstream bus until the fault is cleared. + + maxim,send-flush-out-sequence: + type: boolean + description: Send a flush-out sequence to stuck auxiliary buses + automatically after a stuck channel is being detected. + + maxim,preconnection-wiggle-test-enable: + type: boolean + description: Send a STOP condition to the auxiliary buses when the switch + register activates a channel to detect a stuck high fault. On fault the + channel is isolated from the upstream bus. + required: - compatible - reg @@ -95,6 +112,20 @@ allOf: "#interrupt-cells": false interrupt-controller: false + - if: + not: + properties: + compatible: + contains: + enum: + - maxim,max7357 + - maxim,max7358 + then: + properties: + maxim,isolate-stuck-channel: false + maxim,send-flush-out-sequence: false + maxim,preconnection-wiggle-test-enable: false + unevaluatedProperties: false examples: