From patchwork Thu Jun 16 01:37:45 2022 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Frank Zago X-Patchwork-Id: 1644061 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=2620:137:e000::1:20; helo=out1.vger.email; envelope-from=linux-i2c-owner@vger.kernel.org; receiver=) Received: from out1.vger.email (out1.vger.email [IPv6:2620:137:e000::1:20]) by bilbo.ozlabs.org (Postfix) with ESMTP id 4LNlDj6ZdMz9sFx for ; Thu, 16 Jun 2022 11:38:13 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1357523AbiFPBiM (ORCPT ); Wed, 15 Jun 2022 21:38:12 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:43422 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1357147AbiFPBiI (ORCPT ); Wed, 15 Jun 2022 21:38:08 -0400 Received: from relay12.mail.gandi.net (relay12.mail.gandi.net [IPv6:2001:4b98:dc4:8::232]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 3F56D56C10; Wed, 15 Jun 2022 18:38:05 -0700 (PDT) Received: (Authenticated sender: frank@zago.net) by mail.gandi.net (Postfix) with ESMTPSA id 51A41200004; Thu, 16 Jun 2022 01:38:00 +0000 (UTC) From: frank zago To: Greg Kroah-Hartman , linux-kernel@vger.kernel.org, Bartosz Golaszewski , Wolfram Sang , Johan Hovold , linux-usb@vger.kernel.org, Lee Jones , Linus Walleij , linux-gpio@vger.kernel.org, linux-i2c@vger.kernel.org, frank zago Subject: [PATCH v6 2/4] gpio: ch341: add GPIO MFD cell driver for the CH341 Date: Wed, 15 Jun 2022 20:37:45 -0500 Message-Id: <20220616013747.126051-3-frank@zago.net> X-Mailer: git-send-email 2.32.0 In-Reply-To: <20220616013747.126051-1-frank@zago.net> References: <20220616013747.126051-1-frank@zago.net> MIME-Version: 1.0 X-Spam-Status: No, score=-2.6 required=5.0 tests=BAYES_00,RCVD_IN_DNSWL_LOW, SPF_HELO_NONE,SPF_NONE,T_SCC_BODY_TEXT_LINE autolearn=ham autolearn_force=no version=3.4.6 X-Spam-Checker-Version: SpamAssassin 3.4.6 (2021-04-09) on lindbergh.monkeyblade.net Precedence: bulk List-ID: X-Mailing-List: linux-i2c@vger.kernel.org The GPIO interface offers 16 GPIOs. 6 are read/write, and 10 are read-only. Signed-off-by: frank zago Acked-by: Linus Walleij --- MAINTAINERS | 1 + drivers/gpio/Kconfig | 10 + drivers/gpio/Makefile | 1 + drivers/gpio/gpio-ch341.c | 385 ++++++++++++++++++++++++++++++++++++++ include/linux/mfd/ch341.h | 8 + 5 files changed, 405 insertions(+) create mode 100644 drivers/gpio/gpio-ch341.c diff --git a/MAINTAINERS b/MAINTAINERS index 628eeaa9bf68..8b93f6192704 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -21479,6 +21479,7 @@ WINCHIPHEAD CH341 I2C/GPIO MFD DRIVER M: Frank Zago L: linux-usb@vger.kernel.org S: Maintained +F: drivers/gpio/gpio-ch341.c F: drivers/mfd/ch341-core.c F: include/linux/mfd/ch341.h diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index b01961999ced..473b6e7226ca 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -1653,6 +1653,16 @@ endmenu menu "USB GPIO expanders" depends on USB +config GPIO_CH341 + tristate "CH341 USB to GPIO support" + select MFD_CH341 + help + If you say yes to this option, GPIO support will be included for the + WCH CH341, a USB to I2C/SPI/GPIO interface. + + This driver can also be built as a module. If so, the module + will be called gpio-ch341. + config GPIO_VIPERBOARD tristate "Viperboard GPIO a & b support" depends on MFD_VIPERBOARD diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 14352f6dfe8e..beef802cbfb1 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -44,6 +44,7 @@ obj-$(CONFIG_GPIO_BD9571MWV) += gpio-bd9571mwv.o obj-$(CONFIG_GPIO_BRCMSTB) += gpio-brcmstb.o obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o obj-$(CONFIG_GPIO_CADENCE) += gpio-cadence.o +obj-$(CONFIG_GPIO_CH341) += gpio-ch341.o obj-$(CONFIG_GPIO_CLPS711X) += gpio-clps711x.o obj-$(CONFIG_GPIO_SNPS_CREG) += gpio-creg-snps.o obj-$(CONFIG_GPIO_CRYSTAL_COVE) += gpio-crystalcove.o diff --git a/drivers/gpio/gpio-ch341.c b/drivers/gpio/gpio-ch341.c new file mode 100644 index 000000000000..233dfe1f2ae8 --- /dev/null +++ b/drivers/gpio/gpio-ch341.c @@ -0,0 +1,385 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * GPIO cell driver for the CH341A and CH341B chips. + * + * Copyright 2022, Frank Zago + * Copyright (c) 2017 Gunar Schorcht (gunar@schorcht.net) + * Copyright (c) 2016 Tse Lun Bien + * Copyright (c) 2014 Marco Gittler + * Copyright (c) 2006-2007 Till Harbaum (Till@Harbaum.org) + */ + +/* + * Notes. + * + * For the CH341, 0=IN, 1=OUT, but for the GPIO subsystem, 1=IN and + * 0=OUT. Translation happens in a couple places. + */ + +#include +#include +#include +#include +#include +#include +#include + +#define CH341_GPIO_NUM_PINS 16 /* Number of GPIO pins */ + +/* GPIO chip commands */ +#define CH341_PARA_CMD_STS 0xA0 /* Get pins status */ +#define CH341_CMD_UIO_STREAM 0xAB /* pin IO stream command */ + +#define CH341_CMD_UIO_STM_OUT 0x80 /* pin IO interface OUT command (D0~D5) */ +#define CH341_CMD_UIO_STM_DIR 0x40 /* pin IO interface DIR command (D0~D5) */ +#define CH341_CMD_UIO_STM_END 0x20 /* pin IO interface END command */ + +#define CH341_USB_MAX_INTR_SIZE 8 + +struct ch341_gpio { + struct gpio_chip gpio; + struct mutex gpio_lock; + u16 gpio_dir; /* 1 bit per pin, 0=IN, 1=OUT. */ + u16 gpio_last_read; /* last GPIO values read */ + u16 gpio_last_written; /* last GPIO values written */ + union { + u8 gpio_buf[SEG_SIZE]; + __le16 gpio_buf_status; + }; + + struct urb *irq_urb; + struct usb_anchor irq_urb_out; + u8 irq_buf[CH341_USB_MAX_INTR_SIZE]; + struct irq_chip irq_chip; + + struct ch341_ddata *ddata; +}; + +/* + * Masks to describe the 16 GPIOs. Pins D0 to D5 (mapped to GPIOs 0 to + * 5) can do input/output, but the other pins are input-only. + */ +static const u16 pin_can_output = 0b111111; + +/* Only GPIO 10 (INT# line) has hardware interrupt */ +#define CH341_GPIO_INT_LINE 10 + +/* Send a command and get a reply if requested */ +static int gpio_transfer(struct ch341_gpio *dev, int out_len, int in_len) +{ + struct ch341_ddata *ddata = dev->ddata; + int actual; + int ret; + + mutex_lock(&ddata->usb_lock); + + ret = usb_bulk_msg(ddata->usb_dev, + usb_sndbulkpipe(ddata->usb_dev, ddata->ep_out), + dev->gpio_buf, out_len, + &actual, DEFAULT_TIMEOUT_MS); + if (ret < 0) + goto out_unlock; + + if (in_len == 0) + goto out_unlock; + + ret = usb_bulk_msg(ddata->usb_dev, + usb_rcvbulkpipe(ddata->usb_dev, ddata->ep_in), + dev->gpio_buf, SEG_SIZE, &actual, DEFAULT_TIMEOUT_MS); + +out_unlock: + mutex_unlock(&ddata->usb_lock); + + if (ret < 0) + return ret; + + return actual; +} + +/* Read the GPIO line status. */ +static int read_inputs(struct ch341_gpio *dev) +{ + int ret; + + mutex_lock(&dev->gpio_lock); + + dev->gpio_buf[0] = CH341_PARA_CMD_STS; + + ret = gpio_transfer(dev, 1, 1); + + /* + * The status command returns 6 bytes of data. Byte 0 has + * status for lines 0 to 7, and byte 1 is lines 8 to 15. The + * 3rd has the status for the SCL/SDA/SCK pins. The 4th byte + * might have some remaining pin status. Byte 5 and 6 content + * is unknown. + */ + if (ret == 6) + dev->gpio_last_read = le16_to_cpu(dev->gpio_buf_status); + else + ret = -EIO; + + mutex_unlock(&dev->gpio_lock); + + if (ret < 0) + return ret; + + return 0; +} + +static int ch341_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct ch341_gpio *dev = gpiochip_get_data(chip); + int ret; + + ret = read_inputs(dev); + if (ret) + return ret; + + return !!(dev->gpio_last_read & BIT(offset)); +} + +static int ch341_gpio_get_multiple(struct gpio_chip *chip, + unsigned long *mask, unsigned long *bits) +{ + struct ch341_gpio *dev = gpiochip_get_data(chip); + int ret; + + ret = read_inputs(dev); + if (ret) + return ret; + + *bits = dev->gpio_last_read & *mask; + + return 0; +} + +static void write_outputs(struct ch341_gpio *dev) +{ + mutex_lock(&dev->gpio_lock); + + /* Only the first 6 lines can output. */ + dev->gpio_buf[0] = CH341_CMD_UIO_STREAM; + dev->gpio_buf[1] = CH341_CMD_UIO_STM_DIR | (dev->gpio_dir & pin_can_output); + dev->gpio_buf[2] = CH341_CMD_UIO_STM_OUT | + (dev->gpio_last_written & dev->gpio_dir & pin_can_output); + dev->gpio_buf[3] = CH341_CMD_UIO_STM_END; + + gpio_transfer(dev, 4, 0); + + mutex_unlock(&dev->gpio_lock); +} + +static void ch341_gpio_set(struct gpio_chip *chip, unsigned int offset, int value) +{ + struct ch341_gpio *dev = gpiochip_get_data(chip); + + if (value) + dev->gpio_last_written |= BIT(offset); + else + dev->gpio_last_written &= ~BIT(offset); + + write_outputs(dev); +} + +static void ch341_gpio_set_multiple(struct gpio_chip *chip, + unsigned long *mask, unsigned long *bits) +{ + struct ch341_gpio *dev = gpiochip_get_data(chip); + + dev->gpio_last_written = (dev->gpio_last_written & ~*mask) | (*bits & *mask); + + write_outputs(dev); +} + +static int ch341_gpio_get_direction(struct gpio_chip *chip, + unsigned int offset) +{ + struct ch341_gpio *dev = gpiochip_get_data(chip); + + return !(dev->gpio_dir & BIT(offset)); +} + +static int ch341_gpio_direction_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct ch341_gpio *dev = gpiochip_get_data(chip); + + dev->gpio_dir &= ~BIT(offset); + + write_outputs(dev); + + return 0; +} + +static int ch341_gpio_direction_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct ch341_gpio *dev = gpiochip_get_data(chip); + u16 mask = BIT(offset); + + if (!(pin_can_output & mask)) + return -EINVAL; + + dev->gpio_dir |= mask; + + ch341_gpio_set(chip, offset, value); + + return 0; +} + +static void ch341_complete_intr_urb(struct urb *urb) +{ + struct ch341_gpio *dev = urb->context; + int ret; + + if (urb->status) { + usb_unanchor_urb(dev->irq_urb); + } else { + /* + * Data is 8 bytes. Byte 0 might be the length of + * significant data, which is 3 more bytes. Bytes 1 + * and 2, and possibly 3, are the pin status. The byte + * order is different than for the GET_STATUS + * command. Byte 1 is GPIOs 8 to 15, and byte 2 is + * GPIOs 0 to 7. + */ + + handle_nested_irq(irq_find_mapping(dev->gpio.irq.domain, + CH341_GPIO_INT_LINE)); + + ret = usb_submit_urb(dev->irq_urb, GFP_ATOMIC); + if (ret) + usb_unanchor_urb(dev->irq_urb); + } +} + +static int ch341_gpio_irq_set_type(struct irq_data *data, unsigned int flow_type) +{ + const unsigned long offset = irqd_to_hwirq(data); + + if (offset != CH341_GPIO_INT_LINE || flow_type != IRQ_TYPE_EDGE_RISING) + return -EINVAL; + + return 0; +} + +static void ch341_gpio_irq_enable(struct irq_data *data) +{ + struct ch341_gpio *dev = irq_data_get_irq_chip_data(data); + int ret; + + /* + * The URB might have just been unlinked in + * ch341_gpio_irq_disable, but the completion handler hasn't + * been called yet. + */ + if (!usb_wait_anchor_empty_timeout(&dev->irq_urb_out, 5000)) + usb_kill_anchored_urbs(&dev->irq_urb_out); + + usb_anchor_urb(dev->irq_urb, &dev->irq_urb_out); + ret = usb_submit_urb(dev->irq_urb, GFP_KERNEL); + if (ret) + usb_unanchor_urb(dev->irq_urb); +} + +static void ch341_gpio_irq_disable(struct irq_data *data) +{ + struct ch341_gpio *dev = irq_data_get_irq_chip_data(data); + + usb_unlink_urb(dev->irq_urb); +} + +static int ch341_gpio_remove(struct platform_device *pdev) +{ + struct ch341_gpio *dev = platform_get_drvdata(pdev); + + usb_kill_anchored_urbs(&dev->irq_urb_out); + gpiochip_remove(&dev->gpio); + usb_free_urb(dev->irq_urb); + + return 0; +} + +static const struct irq_chip ch341_irqchip = { + .name = "CH341", + .irq_set_type = ch341_gpio_irq_set_type, + .irq_enable = ch341_gpio_irq_enable, + .irq_disable = ch341_gpio_irq_disable, + .flags = IRQCHIP_IMMUTABLE, + GPIOCHIP_IRQ_RESOURCE_HELPERS, +}; + +static int ch341_gpio_probe(struct platform_device *pdev) +{ + struct ch341_ddata *ddata = dev_get_drvdata(pdev->dev.parent); + struct gpio_irq_chip *girq; + struct ch341_gpio *dev; + struct gpio_chip *gpio; + int ret; + + dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL); + if (dev == NULL) + return -ENOMEM; + + platform_set_drvdata(pdev, dev); + dev->ddata = ddata; + mutex_init(&dev->gpio_lock); + + gpio = &dev->gpio; + gpio->label = dev_name(&pdev->dev); + gpio->parent = &pdev->dev; + gpio->owner = THIS_MODULE; + gpio->get_direction = ch341_gpio_get_direction; + gpio->direction_input = ch341_gpio_direction_input; + gpio->direction_output = ch341_gpio_direction_output; + gpio->get = ch341_gpio_get; + gpio->get_multiple = ch341_gpio_get_multiple; + gpio->set = ch341_gpio_set; + gpio->set_multiple = ch341_gpio_set_multiple; + gpio->base = -1; + gpio->ngpio = CH341_GPIO_NUM_PINS; + gpio->can_sleep = true; + + girq = &gpio->irq; + gpio_irq_chip_set_chip(girq, &ch341_irqchip); + girq->handler = handle_simple_irq; + girq->default_type = IRQ_TYPE_NONE; + + /* Create an URB for handling interrupt */ + dev->irq_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!dev->irq_urb) + return dev_err_probe(&pdev->dev, -ENOMEM, "Cannot allocate the int URB\n"); + + usb_fill_int_urb(dev->irq_urb, ddata->usb_dev, + usb_rcvintpipe(ddata->usb_dev, ddata->ep_intr), + dev->irq_buf, CH341_USB_MAX_INTR_SIZE, + ch341_complete_intr_urb, dev, ddata->ep_intr_interval); + + init_usb_anchor(&dev->irq_urb_out); + + ret = gpiochip_add_data(gpio, dev); + if (ret) { + ret = dev_err_probe(&pdev->dev, ret, "Could not add GPIO\n"); + goto release_urb; + } + + return 0; + +release_urb: + usb_free_urb(dev->irq_urb); + + return ret; +} + +static struct platform_driver ch341_gpio_driver = { + .driver.name = "ch341-gpio", + .probe = ch341_gpio_probe, + .remove = ch341_gpio_remove, +}; +module_platform_driver(ch341_gpio_driver); + +MODULE_AUTHOR("Frank Zago "); +MODULE_DESCRIPTION("CH341 USB to GPIO"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:ch341-gpio"); diff --git a/include/linux/mfd/ch341.h b/include/linux/mfd/ch341.h index 44f5da0720bd..804d671fbe45 100644 --- a/include/linux/mfd/ch341.h +++ b/include/linux/mfd/ch341.h @@ -4,6 +4,14 @@ #include #include +#define DEFAULT_TIMEOUT_MS 1000 /* 1s USB requests timeout */ + +/* + * All commands fit inside a 32-byte segment. There may be several of + * these segments in a USB command. + */ +#define SEG_SIZE 32 + struct usb_device; struct usb_interface;