diff mbox

i2c:i2c-bfin-twi: Read and write the FIFO in loop.

Message ID 1369737669-14226-1-git-send-email-sonic.adi@gmail.com
State Accepted
Headers show

Commit Message

Sonic Zhang May 28, 2013, 10:41 a.m. UTC 
From: Sonic Zhang <sonic.zhang@analog.com>

Reported-by: Bob Maris <mail@maris-ee.eu>

TWI transfer interrupts may be lost when system is heavily handling other
interrupts, while current transfer handler depends on each accurate interrupt
and misses some data in this case. Because there are 2 2-byte FIFOs in blackfin
TWI controller, the occurrence of the data loss can be reduced by reading till
the RX FIFO is empty and writing till the TX FIFO is full.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
---
 drivers/i2c/busses/i2c-bfin-twi.c | 47 ++++++++++++++++++++++-----------------
 1 file changed, 27 insertions(+), 20 deletions(-)

Comments

Wolfram Sang June 12, 2013, 6:13 p.m. UTC | #1 
On Tue, May 28, 2013 at 06:41:09PM +0800, Sonic Zhang wrote:
> From: Sonic Zhang <sonic.zhang@analog.com>
> 
> Reported-by: Bob Maris <mail@maris-ee.eu>
> 
> TWI transfer interrupts may be lost when system is heavily handling other
> interrupts, while current transfer handler depends on each accurate interrupt
> and misses some data in this case. Because there are 2 2-byte FIFOs in blackfin
> TWI controller, the occurrence of the data loss can be reduced by reading till
> the RX FIFO is empty and writing till the TX FIFO is full.
> 
> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Applied to for-next, thanks!
diff mbox

Patch

diff --git a/drivers/i2c/busses/i2c-bfin-twi.c b/drivers/i2c/busses/i2c-bfin-twi.c
index 05080c4..13ea1c2 100644
--- a/drivers/i2c/busses/i2c-bfin-twi.c
+++ b/drivers/i2c/busses/i2c-bfin-twi.c
@@ -39,33 +39,40 @@  static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 	unsigned short mast_stat = read_MASTER_STAT(iface);
 
 	if (twi_int_status & XMTSERV) {
+		if (iface->writeNum <= 0) {
+			/* start receive immediately after complete sending in
+			 * combine mode.
+			 */
+			if (iface->cur_mode == TWI_I2C_MODE_COMBINED)
+				write_MASTER_CTL(iface,
+					read_MASTER_CTL(iface) | MDIR);
+			else if (iface->manual_stop)
+				write_MASTER_CTL(iface,
+					read_MASTER_CTL(iface) | STOP);
+			else if (iface->cur_mode == TWI_I2C_MODE_REPEAT &&
+				iface->cur_msg + 1 < iface->msg_num) {
+				if (iface->pmsg[iface->cur_msg + 1].flags &
+					I2C_M_RD)
+					write_MASTER_CTL(iface,
+						read_MASTER_CTL(iface) |
+						MDIR);
+				else
+					write_MASTER_CTL(iface,
+						read_MASTER_CTL(iface) &
+						~MDIR);
+			}
+		}
 		/* Transmit next data */
-		if (iface->writeNum > 0) {
+		while (iface->writeNum > 0 &&
+			(read_FIFO_STAT(iface) & XMTSTAT) != XMT_FULL) {
 			SSYNC();
 			write_XMT_DATA8(iface, *(iface->transPtr++));
 			iface->writeNum--;
 		}
-		/* start receive immediately after complete sending in
-		 * combine mode.
-		 */
-		else if (iface->cur_mode == TWI_I2C_MODE_COMBINED)
-			write_MASTER_CTL(iface,
-				read_MASTER_CTL(iface) | MDIR);
-		else if (iface->manual_stop)
-			write_MASTER_CTL(iface,
-				read_MASTER_CTL(iface) | STOP);
-		else if (iface->cur_mode == TWI_I2C_MODE_REPEAT &&
-		         iface->cur_msg + 1 < iface->msg_num) {
-			if (iface->pmsg[iface->cur_msg + 1].flags & I2C_M_RD)
-				write_MASTER_CTL(iface,
-					read_MASTER_CTL(iface) | MDIR);
-			else
-				write_MASTER_CTL(iface,
-					read_MASTER_CTL(iface) & ~MDIR);
-		}
 	}
 	if (twi_int_status & RCVSERV) {
-		if (iface->readNum > 0) {
+		while (iface->readNum > 0 &&
+			(read_FIFO_STAT(iface) & RCVSTAT)) {
 			/* Receive next data */
 			*(iface->transPtr) = read_RCV_DATA8(iface);
 			if (iface->cur_mode == TWI_I2C_MODE_COMBINED) {